Search Documents

By Jogeshwara Sahu, Sapan Kumar Kandi, SANDEEP KUMAR JENA, Sachida Nanda Sahu, Sarada Prasad Das

The present article reports the recovery of potassium from mica scrap using carbide lime waste and NaCl. The acid leaching of mica [4 M H2SO4 at 90 °C] can recover a maximum of 25% potassium. However, in the chlorination roasting (with CLW and NaCl) water leaching process, it was possible to recover potassium to the tune of 94% [900 °C, 50 min roasting; mica:CLW:NaCl 1:0.75:1]. The formation of water-soluble phase like sylvite (KCl) and water-insoluble phases like anorthite ( CaAl2Si2O8) and nepheline ( NaAlSiO4) confirms the complete breakdown of the mica crystal structure. The extraction mechanism proceeds with the formation of a transition state followed by the release of potassium as KCl. The characterisation studies using ICP-OES, XRD, FTIR and FESEM support the proposed extraction mechanism. The salt produced by the evaporation of roast-leached liquor confirms the presence of sylvite and halite only, which can be separated to get the fertiliser grade KCl.

Sep 29, 2021

By Mohamed A. Younis, Robert J. F. Goodfellow

This paper investigates the design approaches taken and the philosophy employed during the construction of the Metropolitan Airport Commission (MAC) storm tunnels, part of the Phase 4 Segment of the MAC Trunk Storm Sewer Project at Minneapolis St.-Paul International Airport, located in Minneapolis, Minnesota. URS Corporation was retained to provide a design and Construction Management (CM)services for the MAC Trunk Storm Sewer Project. A case history of the design and construction challenges of the project is presented. The MAC storm tunnels consisted of the construction of twin 10-foot inside diameter (I.D.) tunnels within 7 feet of an existing 72-inch I.D. storm pipe at the base of a 70-foot high highway embankment. The analysis required during the design stage of the project is discussed. This analysis and our design approach provided a defensible framework and justification to make design decisions on relevant issues including: allowable spacing of new and existing structures; preferred order of construction; expected ground deformation behavior; response of lining types to adjacent construction; and effects of proposed changes to design at the submittal stage and during construction.

Jan 1, 2003

By F. Habashi

Siberia, a vast country rich in mineral resources and a large number of different ethnic groups. To the east of Lake Baikal is Buryatia with capital Ulan Ude. The Buryat are closely related to the Mongolians. Ulan Ude is connected to Ulaan Baatar (Ulan Bator) the capital of Mongolia by train – a 26 hours trip. Getting a visa to Russia is not a simple case. Visits to metallurgical research laboratories, Lake Baikal, and historical museums are enriching experience.

Jan 1, 2006

By William Gleason

"It is the largest mining exhibition in the world that attracts thousands of attendees from around the world to Las Vegas, NV once every four years. Despite the recent struggles in the mining industry, MINExpo International 2016 promises to be as big as ever. In the following pages, Mining Engineering takes a look what some of the more than 1,800 companies plan to showcase during the three-day exhibition.CaterpillarCaterpillar will support MINExpo 2016 with an exhibit showcasing machines, technology, expertise and practical knowledge that miners can apply to help address their cost, productivity and efficiency challenges in today’s mining environment.Caterpillar will once again occupy the largest space at the event and will showcase both surface and underground machines, but the talk at the booth will focus on how Cat technology and know-how combines to help mining operations address and solve the issues that are most important to them. The main stage in the exhibit will feature presentations describing how mining companies, Cat dealers and Caterpillar work together to improve operations.“The challenge for all in the mining industry now is to optimize operations — to drive costs down while creating sustainable businesses that can weather downturns,” said Caterpillar Resource Industries group president Denise Johnson. “We believe that through our expertise and the knowledge of our dealers —combined with innovative technologies and our growing data analysis capabilities — we can help them not only survive, but thrive in these challenging times.” Johnson was selected by the National Mining Association (NMA) to chair MINExpo 2016. “Chairing this show is a great honor, and it’s a testament to Caterpillar’s partnership with this critical industry,” she said. “We’re proud to be a long-time supporter of the NMA, and we are excited to participate in another MINExpo. It’s an opportunity for us all to learn from each other how to increase productivity, control costs and improve overall operations.”Surface mining displays. The surface mining section of the Caterpillar exhibit will showcase the new MD6420C rotary drill. This is autonomy ready and optionally equipped to leverage the safety and productivity benefits of Cat MineStar Terrain. This high-precision drill management system optimizes utilization and improves drilling and blasting operations by accurately guiding the operator and improving precision of hole placement and drilling depth — and the next step is fully autonomous operation, Command for drilling. The third-generation drill incorporates proven Cat components throughout for superior reliability and durability."

Sep 1, 2016

By QINGXIANG CAI, Lin Li, PENG LIU, IZHAR MITHAL JISKANI, XIANG LU, Wei Zhou, YONGLI ZHOU

The concept of green mining is to improve the mining industry in a holistic way so that it is safe, efficient, and environmentally sustainable. The purpose of this study was to develop an evaluation index system of green surface mining based on the theory of green grades. The evaluation model is comprised of three attributes (safety, efficiency, and environment), nine criteria, and 35 indicators. The fuzzy comprehensive evaluation method was used to determine the weights of indicators by taking into consideration degree centrality, closeness centrality, and betweenness centrality. Findings indicate that the environment is the most critical aspect of green surface mining, followed by efficiency and safety. The top five ranked green mining success indicators were the application of new technology, starting-off-rate of equipment, science and technology input to total investment, the number of accidents (decreased), and the production (increased). It was observed that more improvements are needed to overcome water, air, waste, and sound pollution. Attention should also be paid to land reclamation and post-mining land uses, which are key factors in green mining. The proposed model can be applied to evaluate and improve the level of green surface mining in other regions. This study provides a tool for decision-makers that can offer technical assistance to green mining.

May 26, 2020

By P. D. Morrell

Jetbelt is the trade name for the air supported belt conveyor. It does not use troughing rollers. Jetbelt conveyors support the conveyor belt on a thin film of air. The belt rides in a steel trough which has small holes equally spaced along the bottom of the trough. Air comes through the holes under the belt, thereby supporting the belt. The air pressure is provided by a single centrifugal blower that creates very low pressure, between 249 Pa and747 Pa [10" and 30" water column], depending upon the tonnage being conveyed. The volume of air required ranges between .001415 m3/S and .00283 m3/S [3 and 6 CFM] per lineal foot of conveyor. Therefore, depending on tonnage being conveyed, a 304.8m[1000'] conveyor might require as little as 1.415m3/S [3000 CFM] or as much as 2.83m3/S [6000 CFM.]. (See Figure 1) Horsepower requirements can be less than troughing idler conveyors and considerably less than some other forms of bulk conveying. Savings are most significant in horizontal and down hill (regenerative) conveyor designs. Horsepower to lift material, of course, does not change.

Jan 1, 1984

By J. Drelich

The wetting behavior of liquid polymers at solid surfaces and the adhesion forces involved at polymer-filler interfaces should always be considered in the fabrication of high quality polymer composites, including those made with mineral fillers. Spontaneous polymer spreading over the filler surface is a basic condition in the fabrication of the polymer-mineral composites. In this regard, the wetting and adhesion characteristics of polymer-mineral systems are reviewed in this contribution. It appears that several aspects of wetting phenomena at mineral filler surfaces are not well described in the literature and require further systematic study. Specifically, it is clear from this review that efforts should be made to determine the effects of mineral surface contamination (including surface hydration) on wetting and adhesion phenomena, and to determine the wetting characteristics of molten polymers at mineral filler surfaces. It is expected that any improved fundamental understanding of wetting and adhesion phenomena for the polymer-mineral composites will provide the basis for further technological development.

Jan 1, 1995

By Stephen J. Swan

Feed-forward control (i.e. the forward flow of information in a control system ) is a simple and flexible approach to over-all control of a ball mill-rake classifier grinding circuit. The system described here uses mill power, feed rate, mill dilution water flow rate, and classifier dilution water flow rate only, to control mill load, throughput, mill solids, and classifier solids as well as classifier overflow grind. The mill load is controlled by a simple feed-back control loop, while mill solids and overflow grind are controlled within close limits by a unique non-linear feed-forward water control system. In effect the control follows a limited mathematical model of the grinding circuit. The configuration minimizes deviations in overflow grind due to changing ore conditions, but since it is open-loop, and the model is not complete, it is affected by changes in total ball charge and liner wear. These effects are fortunately gradual, and changes in the grind can usually be kept to within ± 1% of a target continuously for several days without adjustment. Control adjustments are made with feed-back from laboratory composites. This control system has won enthusiastic operator acceptance; it is easily started up and shut down; grind-outs have been eliminated along with flotation machine flooding and mill spills. Standard measurements and components are used throughout providing a trouble-free system design at a moderate cost.

Jan 1, 1970

By Arthur R. Still, Paul A. Bailly

5.1-PURPOSE, PROCEDURE, METHODS, MANAGEMENT Exploration can be technologically defined, with regard to the discovery of new mineral deposits, as all the activities and evaluations necessary before an intelligent decision can be made establishing size, initial flowsheet and annual output of new extractive operations. The purpose of mineral exploration is the discovery and acquisition of new mineral deposits amenable to economic extractive operations now or in the future. A prime objective of mineral exploration, however, is to find and acquire a maximum number of such mineral deposits at a minimum cost and within a minimum time. Immediately upon the heels of a successful ''exploration" discovery follow activities called, first, development, then operation. Under U.S. Internal Revenue Code regulations (Secs. 1.615.1 and 1.616.1) in effect at the time of this writing, which state that the "development stage" has been reached when "deposits of ore or other minerals are shown to exist in sufficient quantity and quality to reasonably justify commercial exploitation by the taxpayer," exploration in the technological sense may well continue after a mineral property has entered the "development stage" as defined for tax purposes. In many instances continued exploration, after reaching the tax defined "development stage," has disclosed additional reserves which justify a much larger, more efficient and more profitable operation than that which would constitute the minimum feasible. Even after a mine goes into production, continued ore search generally will increase the reserves, either justifying expansions in plant capacity or prolonging the life of the operation, but this work (actually "exploration") is normally considered, for bookkeeping and tax purposes, a part of mine development. Each exploration entity defines its own objectives in terms of acceptable mini- mum rate of return on investment for any deposit found and retained, and in terms of which commodities, and markets, are to be involved. For these reasons, exploration programs, and aims, will vary over a wide range, although all have the common objective of endeavouring to create new profit centers for the future. 5.1.2-EXPLORATION METHODS Exploration has evolved in the past several decades into a highly sophisticated and expensive endeavor in which large corporate entities, or subsidaries, normally are directed and staffed by highly trained exploration specialists. In some instances consultants, with expertise in a given field, are utilized to the benefit of such corporate groups. The "grasshopper" approach to exploration-searching only for outcropping minerals and/or investigating only mineral prospects offered by the discoverers of such outcrops has given us most of the past and present mines in the US., but this method is rapidly approaching the point of diminishing returns in areas that have been thoroughly prospected for currently marketable commodities. With

Jan 1, 1973

By Rasik H. Raythatha

Calcium carbonate is perhaps the most widely used mineral in the world. With total consumption of all calcium carbonate exceeding over 25 million tom per year, within this class of filler, a relatively smaller segment of precipitated calcium carbonates (PCC) is often misunderstood as a commodity product and bundled in the same category as ground calcium carbonate. However, each material has a distinctly digerent role and characteristics. Precipitated calcium carbonates are used to influence specific performance in a specific application whereas ground calcium carbonate is used primarily to reduce cost in many applications. In this paper, attempts are made to demonstrate the role of nano-fine-PCC in improving shear-thinning characteristics of common and specialized sealants and automotive underbody coating and how such "nano-particle" cal- cium carbonate properties can be exploited to process PVC plastics while reducing overall cost. We also review the role of precipitated calcium carbonate as "nano" material and why it must be viewed as a specialty additive.

Jan 1, 2003

By P. M. Soupios

There is an increasing requirement for geophysical surveys carried out during geotechnical investigations to provide direct information about rock quality or other geotechnical parameters. With the paucity of information to correlate geophysical results with actual rock properties, this is still difficult to achieve and additional research effort needs to be performed to address this issue. Nowadays, several researchers have been described detailed studies which designed specifically to investigate this matter. Generally, geophysical techniques which are used to estimate seismic velocities in the subsurface focus on the low strain levels that are not large enough to induce significant nonlinear, nonelastic stress-strain behavior (Luna and Jadi, 2000), which is normally evaluated when addressing liquefaction potential of soils in the shallow subsurface. Soil parameters relevant to seismic ground response (Rechtien, 1996) are density, relative density and void ratio, permeability, shear modulus, water saturation, soil fabric and stress history. Detailed characterization of elastic properties near a major construction site (e.g. a bridge) is useful for near field dynamic analysis of soil-structure interaction (SSI) effects. The coupled effect of the bridge foundation (piles, piers or abutments) and the soil immediately surrounding these substructure elements is essential for dynamic SSI analysis of these critical bridge structures. This paper presents a geophysical investigation performed along the under construction highway of Egnatia Odos, approximately 13 km west from the town of Xanthi in N. Greece. Twelve geotechnical boreholes, drilled at the maximum depth of 75 m, approximately located 20 m from the Nestos River. The objective of the survey was to obtain the high-resolution compressional and shear wave velocities of the shallow subsurface for computation of elastic engineering properties of the unconsolidated material interposed between the investigated boreholes. Joint interpretation of borehole logs and velocity images obtained by P- and S-wave traveltime inversions outlined shallow geological anomalies.

Jan 1, 2005

By ZHONGLING ZHAO, WANTING SONG, GUOZHONG LIU, LEIXIN SHI, ZUI WANG, YUANYUAN LIU, KE GAO, DONGHONG JIANG, WANG LUO, PEICHAO LU, Jianwei Cheng, WANCHENG ZHENG, Gang Zhao, YUNGANG WANG, JIANBING ZHAO

Coal spontaneous combustion is one of the disasters occurring in underground coal mines. As a typical case, the spontaneous combustion of broken coal left in the longwall gobs often happen which could greatly interrupt the normal mining production. Such concealed thermal event is featured as rapid development and difficulty in locating “hot” spots. If such spontaneous combustion fails to be timely prevented and controlled, a large amount of toxic gases (mainly CO) and smoke could flow and diffuse in the underground working sections, which could present safety hazards for coal miners. In this paper, based on an coal spontaneous combustion event happened in a Chinese gassy mine, the fire ratios derived from the gas composition data obtained through the tube bundle mine atmospheric monitoring system are used in determining the fire status. A comprehensive and collaborative fire extinguishing effort including inert gas injection, underground pressure balance, and sealing enhancement are made to control the fire progress. Simultaneously, the effects of such works to control the spontaneous combustion event have also been quantified using the fire ratios to justify again. Finally, the danger of coal spontaneous combustion in gob is eliminated, and the longwall panel is successfully re-opened for normal production.

May 6, 2021

By Jorgen Elbrond

The capacity calculation of complex transportation systems involving variable activity times such as encountered in the mining industry are often worked out by means of simulation, which reconstructs waiting times and cycle times. The queuing theory, which mathematically calculates waiting times, has been used mainly to describe the, phenomena. This is due partly to the difficulties encountered in modelling complex systems and partly to the difficulty of reconciling the required time distribution laws with the real phenomena by means of the queuing theory. It is, however, obvious that formulas for capacity calculations would be preferable to simulation procedures because of their higher calculation speed, shorter and more flexible programs and shorter programming work. The calculation procedure presented in this paper is composed of some rather simple models, which are based on the queuing theory, and on some probabilistic and some deterministic considerations. The models are supported by observations, and to some extent by simulations. It has been attempted to find all the components of the cycle time and to include them in a comprehensive model. It is the intention to demonstrate that even quite complex mine transportation systems can be treated by means of the queuing theory with the advantages mentionned above and, without sacrificing the precision of the estimates. The speed of calculation of a wide range of parameter combinations is such that the procedure can be used extensively by a project engineer in the search for optimal modifications of the entire transportation system.

Jan 1, 1979

By Bodo Peinemann

For more than 35 years Lurgi has been providing its fluid bed roasters on a world­wide basis. The current total annual capaci­ty of the 250 Lurgi roasters approaches 26 million mt of sulphide minerals, including gold-bearing flotation pyrite concentrates. While the stationary fluid bed has been uti­lized for roasting exclusively, Lurgi has now commercially introduced its Circulating Fluid Bed (CFB) technology for gold roasting in a successful effort to maximize gold re­covery.

Jan 1, 1990

By Haydn H. Murray

Kaolin is defined and described as an industrial mineral. In addition the types of deposits -primary and secondary are defined and the genesis of kaolin from feldspars and other minerals discussed. The major deposits of the world found in the United States, Great Britain, Brazil, and Czechoslovakia are described along with many of the minor kaolin deposits. Four areas which have very large deposits of kaolin could, with technological breakthroughs to reduce viscosity significantly, become important factors in supplying the world markets which are increasing year by year.

Jan 1, 1977

By Lynn B. Hales

Unfortunately, the term "control" has a negative connotation in the minds of many of our operating plant personnel. Whereas the opposite is true of those associated with research and technical centers in our industry. The magnitude of this difference in opinion and actual experience has often proved to be a major factor influencing the success or failure of process control applications. Through the years, many plant people have endured a number of unsuccessful attempts by "outside" people to "optimize" their plants; and these experiences have proved to have had quite a callousing effect on them. On the other hand, in many plants, successful process control efforts have made firm allies of the operating personnel, and have increased the number of metallurgical people who are well qualified and experienced in process control. The instrumentation industry, computer industry, and the mining industry's ability to quantify what is really happening in our processes have grown and developed rapidly since the first control efforts were made in the 1930's (1). Because of this-,: new control opportunities are becoming increasingly more feasible and older well established ones are becoming even more practical and necessary with regard to the economic s of our industry.

Jan 1, 1979

By R. J. Sheets

In 2009, the Gold Quarry openpit mine experienced multiple large-scale slope failures of the upper east highwall that reduced gold ore extraction for nearly 18 months. The slope failures occurred within a weak, consolidated sedimentary sequence that exhibits strength characteristics that are transitional between soil and rock. Instability initiated as mining exposed the lower, high plasticity subunits of the Carlin Formation. This deformation created preferential flow paths that allowed ground water from the upper sandy subunits to infiltrate low-permeability, clay-rich subunits, thereby enhancing deformation of the slope toe, which, in turn, destabilized the upper portion of the highwall. The outcome was a 160 m high slope failure that had a lateral run-out of 850 m. The effort to return the pit to ore production required geotechnical and hydrogeological investigations and the preliminary remediation mining activity to be concurrent. This required the development of detailed safety procedures and a requirement to modify the remediation design as new results were obtained. An initial challenge was to mitigate a near vertical, 90 m headscarp with localized, blast-induced slope failures. Back-analyses with numerical modeling software indicated that the failure surface could be shallower, which contradicted the initial failure interpretations. Eventually, drilling results confirmed this alternative failure geometry. The final remediation design incorporated shallower slope geometries and an approximately 3 Mt buttress along the base of the Carlin Formation and bedrock contact to reinforce the subunits with residual strength properties. The results are a stable highwall within the Carlin Formation following nearly 10 years of repeated slope failures, and an example of the necessity to conduct appropriate geotechnical and hydrogeological studies during the early stages of a new layback evaluation or new openpit development.

By S. K. Bhatt

This paper reviews major developments in continuous haulage technology for underground coal mines. Haulage systems, both in use and development, are investigated through a comprehensive literature search and visits to mines and manufacturers. The systems include flexible conveyor train, mobile conveyor, multiple-unit continuous haulage, extensible, and belt turning systems. Strengths and weaknesses of the systems are assessed in light of their operating under remote control and their application to the computer-assisted continuous mining machine being developed by the U.S. Bureau of mines. Through mining scenarios, candidate haulage systems are conceptualized to be consistent with the capabilities of the mining machine.

Jan 1, 1990

By Taghi Sherizadeh, Kutay E. Karadeniz, Dogukan Guner, Samuel Nowak

Underground mining environments bring occupational health and safety issues with some severe dangers such as mine disasters like explosions. During such events, miners might escape using main access openings, or find a safe haven like refuge alternatives (RAs) to wait and be rescued and evacuated to the surface. In this paper, RAs are explained with their early and current applications. A classification as permanent and portable is explained depending on the conditions and their abilities. This classification is followed by the utilization and survivability of RAs with the requirements and recommendations of the main mining countries. Based on the utilization and survivability constraints, basic human requirements, waiting for a rescue team, and the required physical specifications of RAs during the events are analyzed in detail for various countries with their regulations. Among these, the specification, resistance to the explosion, is discussed in particular, and the studies in the literature are examined in terms of structural deformation. The highest deformed zones, the beneficiation of reinforcing steel components such as stiffeners, and the simulation approaches are investigated through this review.

Sep 24, 2022

By G. Zhu

Bulk and differential laboratory flotation tests have been carried out using a synthetic mixture of chalcopyrite and molybdenum ore. In addition to boiling and roasting, six different depressants are tested so that the best conditions of separation can be identified. These reagents include sodium cyanide with and without zinc sulfate, potassium ferrocyanide, sodium hydrosulfide, arsenic Noke's reagent, and sodium sulfide. The data indicate that most of these reagents are effective chalcopyrite depressants. However, sodium hydrosul fide can be used preferably if economic, operational, and environmental factors are taken into consideration.

Jan 1, 1983