Search Documents

By G. M. Wilemon

The U.S. Bureau of Mines has conducted investigations on extracting phosphate values from wastes generated during the mining and beneficiation of phosphate matrix. These wastes may contain up to one third of the phosphate originally present in untreated ore. Samples of wastes were air-dried and leached using 93 pct sulfuric acid in the presence of methanol. Evidence for the formation of a calcium sulfate hemihydrate coating that hinders complete dissolution of phosphate is presented. Solid-liquid separations were enhanced when flocculation was effected using poly(ethylene oxide) (PEO) in conjunction with hydroxypropyl cellulose (HPC) or hydroxyethyl cellulose (HEC. A conceptual flowsheet for a proposed process using an acid-alcohol leaching technique is presented.

Jan 1, 1990

By A. A. Dor

Recent developments in the design of concentration plants have reflected the increased recognition that has been given to the economic and metallurgical advantages of autogenous grinding. This has manifested itself in the increasing adoption of primary auto genous grinding in iron ore 'beneficiation plants in North America. Table 1 lists eleven major iron ore beneficiation plants which have either been put in operation since 1961 or are under construction at present. Seven out of these eleven plants have adopted primary autogenous grinding. Four of them have coarse grinding mills (8 to 14 mesh) and three have fine grinding primary circuits (48 to 65 mesh). Their nominal capacity totals 26. 2 million ltpy of concentrates or pellets, representing very nearly 75% of the aggregate capacity 135. 3 million ltpy) of the eleven concentrators listed. For a long time there was a tendency to consider that primary autogenous grinding was only applicable to suitable coarse grained ores, However, extensive testing of a very wide variety of ores, and actual operating performance in several commercial plants, seem to have established beyond reasonable doubt, that the majority of mineral ores which the beneficiation engineer may be called upon to process can be ground autogenously. The basis for the selection of autogenous or conventional grinding mills, becomes principally economic and depends on the liberation characteristics of the ores under consideration and their relative hardness and grindability.

Jan 1, 1965

By Matthew S. Sanchez, Richard J. Lee, Matthew D. Zock, Drew R. Van Orden

"Current Environmental Protection Agency (EPA) risk models and asbestos fiber counting techniques for monitoring airborne exposures treat all fibers as being equivalent and ignore the effect of dimension on toxicity. While this may have been appropriate when modern analytical methods were not available, the measurement world is now fully capable of making the appropriate distinctions. The importance of width as a determinant of carcinogenicity has been recognized for nearly 30 years within the published literature. Stanton,1 in a landmark study of a suite of fibrous materials, found that durable mineral fibers with widths less than 0.25 mm and lengths longer than 8 mm were causally associated with the induction of tumors. Pott,2 in a later study, postulated a fiber toxicity model that agreed reasonably well with the Stanton findings, but extended the concept to include varying toxicity as a function of length and width. Wylie et al.3 reanalyzed samples used by Davis et al.4 and found that tumor generation was strongly and inversely correlated with fiber width. Crump5 testified increasing fiber length was correlated with disease occurrence. Lippman6 reviewed a number of studies and suggested that mesothelioma was closely associated with long, thin fibers. Berman et al.7 published a risk model, which found that disease was correlated almost exclusively with fibers longer than 40 mm and width less than 0.25 mm. Recently, Loomis et al.8 reanalyzed textile mill samples and found that aspect ratios greater than 40:1 were highly correlated with disease. Incorporation of width into risk models has been limited by the availability of data from operating asbestos plants and, in particular, the observation of an asbestos plant for which there is no observable mesothelioma. There have been only limited studies published on the dimensions of asbestos fibers, with a few serving as the primary references in other literature.9_13 A rare opportunity to collect detailed concentration and dimensional data of airborne crocidolite from an operating asbestos-cement plant using modern analytical procedures arose, providing a chance to supplement the existing literature on airborne fiber dimensions. The asbestos-cement plant is located in the eastern end of Cochabamba, Bolivia along Highway 4. Cochabamba is a relatively large city located in the Andes Mountains, approximately 250 km southeast of the capital La Paz. The city sits in a valley that runs east-west with mountains to the north and south. The crocidolite used in the products made at this facility is mined in central Bolivia, approximately 75 km northwest of Santa Cruz. The crocidolite is a fibrous magnesioriebeckite 14 (blue asbestos). Crocidolite fibers from Bolivia were the subject of prior reports suggesting the fibers are generally longer and thicker than crocidolite from Australia or South Africa.9 At the cement plant, the run-of-mine crocidolite was first pulverized using a hammer mill and then sieved on vibratory sieves to produce fibers of limited size ranges for use in the cement. The sieved crocidolite is mixed with other components, including recycled cement product, to produce a slurry that is vacuum filtered into sheet form. The sheets are then manually molded into a corrugated shape, air dried, and sawed (using circular saws) to accepted dimensions. The sawed sheets are cured in soaking pits for 28 days before being shipped to the consumer. Prior to shipping, the sheets are finished by a light hand sanding followed (at customer request) by applying one or more coats of paint. A detailed description of the cement plant and the industrial hygiene results can be found in Van Orden et al.15"

Jan 1, 2012

By K. A. Perry, R. Q. Eades

The University of Kentucky conducted inerting tests and angle of ejection tests on three types of rock dust. A newly developed hydrophobic dust was compared against typical dry and wet dust applications. This new product is designed to alleviate respirable dust concerns for dry dusting and caking issues with wet dusting. Samples for both test types were prepared in a laboratory and subjected to temperature and humidity cycles that are typical of an underground coal mine. Inerting tests were conducted in a 38-L chamber with a 5-kJ Sobbe igniter. Angle of ejection testing was conducted at the University of Kentucky Explosives Research Team’s laboratory in Georgetown, KY. The results of these tests indicate that the newly developed dust has improved results for flame suppression and ejection compared with typical wet dust applications. The significance of these results is discussed with regard to existing respirable dust regulations and the issues associated with caking.

Jan 1, 2016

By D. Van Orden, Y. Kamiya, R. Lee, E. Ilgren

Crocidolite is a well-known causative agent for mesothelioma. However, studies have shown that the pathogenicity of the fiber from different mines varies considerably and it has been postulated the parameter that appears most likely to account for this variation is fiber width although this has never been formally confirmed. To date, crocidolite appears to be the only asbestos mineral for which an epidemiological study comparing the risk of mesothelioma in a population exposed to ‘thin’ fibers with another exposed to ‘thick’ fibers of the same species may be carried out. Finnish anthophyllite, South African amosite, and African Transvaal crocidolite can also be classified as thick fibers, and there is a paucity of mesotheliomas in populations exposed to them compared to those exposed to thin Cape crocidolite. No thin occurrences of these minerals are known. Our previous study looked at crocidolite from several sources. The present study considers the amphibole anthophyllite found in many places in the world. This mineral, regardless of source, does not show the same variation in fiber width found with crocidolite from different areas. All anthophyllite fibers that have been mined may be classified as thick and populations exposed show very low levels of mesothelioma. We suggest the most likely explanation is related to the fiber width distribution and a concomitant reduction in the ‘Stanton fiber size’ fraction.

Jan 1, 2012

By D. L. Boreck

With increasing land development, the potential of fatalities from abandoned mine shafts increases. To minimize potential liability, shaft closure should be a critical part of mined land reclamation. The Bureau of Mines is conducting research into using lightweight foam concrete in sealing abandoned coal mine shafts. A demonstration seal consisted of a 3m thick foam concrete plug to provide lateral stability inside the shaft. A high density concrete cap provided load-bearing capacity for a 100-year service life. The USBM has also completed research into changes in foam concrete when it is pumped or dropped from different heights. It is concluded from the research that foam concrete can undergo significant air loss with pumping or dropping. This foretells significant changes in the characteristics of the concrete as well as an increase in the weight and cost of the in-place concrete seal. When using foam concrete to seal abandoned mine shafts, care must be taken to minimize air loss during placement.

Jan 1, 1994

Caterpillar unveiled a new dozer, the new Cat D10T2 dozer, that builds on the success the company has had with its D10T model. The newest version of the dozer includes refinements to its power train, automated controls and structures. The result, the company said, is high productivity with superior fuel efficiency, reliable operation with long-lived structures, as well as enhanced access for service technicians and operators. The D10T2 uses the latest load-sensing hydraulics technology combined with Cat advanced engine controls to maximize the amount of material moved for every drop of fuel burned. Improved filtration protects the fuel system, hydraulic system and power train oil system to help ensure high reliability and minimal machine downtime. Refined large structures, such as redesigned track roller frames, deliver longer service before rebuilds. Improved access and egress features enhance safety and productivity of technicians and operators, and optional powered access systems and platforms enable configuring the D10T2 for the site. Caterpillar offers the D10T2 with two variations of the Cat C27 engine with ACERT Technology. One version is U.S. Environmental Protection Agency (EPA) Tier 4 Final certified, and the other is capable of achieving emission levels equivalent to EPA Tier 2 standards. Both engine configurations produce net power of 447 kW (600 hp) in forward gears and 538 kW (722 hp) in reverse gears. The engine controller automatically adjusts power output based on the direction of travel. With the new system, the D10T2 has about 20 percent more power in reverse compared to its predecessor model. The result is faster cycle times and greater productivity in certain applications. The D10T2 is suited for a variety of applications including mining, heavy construction and bulk materials handling.

Mar 1, 2014

By James R. Garvey

The impact of conversion on the coal industry can be summarized very briefly: We are going to have to mine an awful lot of coal. Fortunately, the United States has the coal reserves available, and given the right conditions, we can mine it. The coal reserves of the United States are enormous. If we consider them on the basis of proved reserves, using the standards of the petroleum industry--that is, resources mapped and explored and recoverable with present techniques at close to present costs--and compare that with the reserves of other fuels, coal constitutes 88 per cent of the proved recoverable energy resources of the nation. That includes oil, natural gas, oil shale and uranium, so long as the uranium is used in burner reactors. If we consider resources on the basis of "ultimate recoverable" reserves, that is, those resources which can be extracted with improved technology and at somewhat higher costs--and if we include those resources of all fuels not yet found but believed to be waiting discovery--coal still accounts for 74 per cent of the national total. We have built a hydrocarbon economy in which about 76 per cent of our total energy needs are supplied by petroleum and natural gas, and about 20 per cent by coal. Domestic resources of oil and gas are running dangerously low and, assuming a continued hydrocarbon economy, the 20 per cent supplied by coal may increase dramatically. We already import nearly a quarter of the petroleum we consume, and the chief source of additional imports seems to lie in the politically unstable Middle East. Natural gas is in even shorter supply, and the problems of importing it seem at least as difficult as those of oil. The fact is, the United States is already relying to an increasing extent on foreign fuel sources. There is an obvious national risk in making an important part of energy supply hostage to foreign governments of uncertain tenure and friendliness. There is also an economic risk--one of the chief reasons for last year's economic freeze was to try to correct the deficit in our balance of payments; it is obvious

Jan 1, 1972

By T. M. Gurr

The United States is the world's leading producer of phosphate rock. In 1975 according to the U. S. Bureau of Mines' statistics, 44.3 million tonnes (48.8 million short tons) of phosphate rock were produced in the United States', which is 40.6 percent of the world's production2. The major phosphate producing areas of the United States are located in Figure 1 and the production for 1975 is listed as follows: Million Million Short Tonnes Tons Florida and North Carolina 36.9 40.7 Western States 5.3 5.8 Tennessee 2.1 2.3 All of these areas produce phosphate from deposits which are sedimentary marine in origin. Occurrences of phosphate exist throughout the United States in numerous locations that are of both igneous and sedimentary origins. However, these other phosphate occurrences vary greatly in extent and economic significance. Georgia, South Carolina, California, Texas, Arkansas, Kansas, Iowa, Alabama, Kentucky and Virginia are but a few of the states in which phosphate is thought or known to

Jan 1, 1977

By Gilmore R. Tostengard

The advent of inexpensive computers has opened vast opportunities for improved planning and control of capital projects. The mining and mineral processing industries have welcomed the opportunity, and new and improved quantitative management techniques have abounded. This chapter will discuss commonly used computer applications for economic justification of the project, preparation of the cost estimate, planning the work schedule, monitoring work progress, and control of costs and productivity. Finally, there is a review of the degree to which the industry uses these applications. Our experience suggests that while we in the industry have been quick to adopt the new techniques, the quality of our input data has not always kept pace. During the next decade, our push should be toward improving the quality of the basic data and assumptions so that we can fully benefit from the sophisticated techniques. The GIGO (garbage in, garbage out) principle is a wellworn cliche, but it is especially valid here. One of the keys to getting good input is commitment. Unless the managers who are to use or benefit from the system are committed to it, the effort will fail. They must be com- mitted to the underlying principles of planning and control sufficiently to expend their time and resources on them; planning should be especially given emphasis. They can't be too busy to plan.

Jan 1, 1979

By J. Bilant, B. Carlson, N. Gow

"High-pressure grinding roll (HPGR) technology was evaluated to replace tertiary cone crushing at Coeur Rochester operations (Coeur Rochester Inc.) as an opportunity to improve silver recovery. In 2016 and 2017, onsite and third-party pilot programs were initiated to evaluate the impact on metallurgical recovery and heap leach performance of crushed product generated by an HPGR. In 2018, Forte Dynamics evaluated the HPGR laboratory metallurgical data from Coeur Rochester and all third parties to develop field-scale leach curves based on new crushing scenarios. The laboratory recovery test work data were consolidated and scaled to field conditions to determine projected heap leach performance. Based on the metallurgical testing conducted, the replacement of current tertiary cone crushers with HPGR technology has the potential to increase Coeur Rochester’s silver recovery rate by 8 percentage points, from 61 percent to 69 percent, and shorten the overall timing of silver recoveries from 20 years to just more than two years.The Rochester Mine, and associated valley fill heap leach facilities is an openpit silver and gold mine located in Pershing County, NV, approximately 42 km (26 miles) northeast of the city of Lovelock. In 2017, Rochester produced approximately 4.7 million oz silver (Ag) and 51,000 troy oz gold (Au). Ore mined at Rochester is either fed directly to the primary X-Pit crusher, crushed at an in-pit crusher system, or placed directly onto a heap leach pad as run-of-mine (ROM). Both crushing circuits are comprised of three stages of crushing to produce a nominal 3/8 in. ore. Primary crushing consists of jaw crushing while secondary and tertiary crushing are composed of varying cone crushers.Historical recovery rates of crushed Rochester ore averaged 61.4 percent Ag and 95.9 percent Au over a period of 20 years (Robinson et al., 2018). These rates were derived from third-party verification of in-house metallurgical test results, crusher production and heap leach production results from 1986 through 2004 in a private report for Rochester produced by KD Engineering Co., Inc. Recovery rates are regularly verified by compositing daily samples of ore delivered to each leach pad from the X-pit crusher, in-pit crusher and/ or ROM. A proportionate split of each sample is used to generate monthly composites for metallurgical analysis utilizing column leaching and bottle roll leaching. These tests are run in a manner analogous with production conditions and deliver test results that provide expected heap leach performance. As the Rochester oxide deposit has been mineralogically and metallurgically consistent, the gold and silver recovery trends have also been consistent over the life of the project."

Sep 1, 2019

By William Gleason

Since 2004, Dave Kanagy has served as the executive director and chief executive officer of SME. In that role, he has worked with 22 SME Presidents, traveling the world to represent the Society. His prestigious one-million-mile status with United Airlines is a testament to these efforts. He has been to six of seven continents while leading the Society on a journey from a struggling association in 2004 to the largest and arguably the most influential professional mining society in the world. In the following pages, some of those past SME Presidents reflect on their time with Kanagy and paint the picture of a visionary leader who was willing to make the hard decisions for the betterment of the Society while remaining open to new ideas and opportunities. One of his first accomplishments as the executive director was to streamline the SME Boad of Directors from 29 members to nine, making it much more effective. With a keen financial sense, he was able to add value while cutting excess to expand the Society in every measure. As the leader of SME, Kanagy helped facilitate much of the Society’s growth and innovation as the world’s largest mining related organization. He has a B.S. degree in industrial education from the University of Maryland, an M.S. degree in technology education from Eastern Illinois University and is a certified association executive by the American Society of Association Executives. Under his leadership, several unique programs were created or advanced, including OneMine.org, the world’s foremost online mining research library. He enhanced legacy programs and increased collaboration with international organizations. Kanagy is the recipient of prestigious awards, including the Colorado Society of Association Executives’ Professional of the Year award and the Mining and Metallurgical Society of America’s Gold Medal award.

Feb 1, 2026

By J. J. Fallon

The subject is "Mergers, Acquisitions and Divestitures in Industrial Minerals, but my remarks could also be applied to new product development, resource development and other new business development activities. At the kernel of the subject is due diligence in major decision-making, that is, where major money amounts and a large corporate commitment are at stake. The "due diligence" means how carefully we do our homework before making the decision. The homework or feasibility study addresses different parts of the decision. In the industrial minerals business the study seeks to uncover the pros and cons in: o The mineral reserves, quantity, quality, mineability, access, etc. o The environmental impact of mining, processing and transporting. o The economics of operations. o Financial aspects o Legal aspects o Many other aspects o And -oh yes! the marketing aspects.

Jan 1, 1990

By T. G. Melkus

A Setaram C-80 heat flux micro- calorimeter was used to study the surface and interfacial properties of fine coal particles in water containing flotation agents via heat of immersion measurements. Heat of immersion (?Himm) is usually a small exothermic quantity and can be used' to characterize a solid in terms of its relative hydrophobicity or hydrophilicity. The effects of coal type, surface oxidation, mineral matter content, kerosene concentration, and pH on the wetting characteristics were investigated. Results obtained from the calorimetry experiments correlated well with results from independent flotation experiments.

Jan 1, 1987

By M. L. Wouden

The Bureau of Mines investigated pegmatite and granite formations at Copper Mountain, Fremont County, Wyoming, for recovery of tantalum and niobium. Sampling of surface exposures identified about 1.27 mega tonne of pegmatite resource material ranging between 0.02 and 0.04% Ta20, and 0.007% Hb20,. Beneficiation studies were conducted involving coarse-grained and fine grained pegmatite samples. Over 80% recovery of the coarse-grained tantalite was achieved in a concentrate averaging over 45% combined tantalum-niobium oxide. Lower concentrate grades and recoveries resulted from the treatment of fine-grained pegmatite.

Jan 1, 1991

By W. G. Pariseau

Face and pillar bursts, bumps and bounces are violent failures that occur in underground coal mines in response to a complicated interplay of face and pillar geometry, seam depth, coal strength and moduli and interactions between roof, seam and floor strata. Additional complications arise from the presence of gas, mainly methane, and associated pressure and flow that vary with time and are further influenced by the rate of face advance. Numerical models provide a means of quantitatively accounting for the various complications of mining geometry, the stratigraphic column, mechanical properties, gas flow properties and associated interactions. A fully coupled hydromechanical finiteelement code, utAH4, serves the purpose well and allows study of the important interaction between stress concentration and gas pressure in determining safety and stability of the face during the advance of a longwall panel in a deep underground coal mine in central Utah. Face advance is relatively fast compared with gas flow and depressurization in coal seams of low gas permeability. Consequently, gas pressure is high at the face. When a longwall is stationary, depressurization occurs at the face, so effective stress and strength increase. thus, when gas flow at the face is high and requires a pause in face advance to bring gas concentration to an acceptable level, a second benefit occurs because of timely depressurization. However, quantitative analysis of a deep coal mine shows that regardless of gas pressure, high stress concentration is more likely to pose a threat to face and pillar wall stability.

Aug 1, 2013

By H. K. Lin

The free-milling ore characteristics of the Fort Knox gold deposit are ideal for studying gold and silver behaviors in various processing circuits without serious interference of sulfide minerals and other refractory factors. A galvanic effect leads to faster silver dissolution than gold dissolution and, as a result, the Au/Ag solution concentration ratio increases through the leach circuit. In the CIP circuit, Au adsorption is more effective than Ag adsorption. The Au/Ag solution concentration ratio decreases from 10.0 to 1.0 as the slurry advances from CIP tank #1 to CIP tank #5, while Au/Ag ratio in the carbon increases from 3.2 to 15.3, as the carbon advances from CIP tank #5 to CIP tank #1. Silver is stripped more effectively than gold from the loaded carbon. The Au/Ag ratio in solution reaches 2.0 in the first 75,700 L of strip solution that pass through the loaded carbon; as the stripping process continues, the Au/Ag ratio in the strip solution increases. In the electrowinning circuit, the Au/Ag ratio in the spent electrowinning solution is significantly lower than that in the electrowinning feed, indicating that Au is more rapidly deposited onto the cathode than Ag.

Jan 1, 2010

By A. J. Basu

Geotechnical design plays a key role in mine design. I A proper geotechnical design provides a safe working environment and facilitates efficient mining operation. There are mainly three design approaches I) judgmental, based on observational and experiential facts, 2) empirical, based on empirical design formulae, and 3) analytical, incorporating numerical analysis. Most design applications are based on the design methods one and two as mentioned earlier. However, complexities arise in deep underground mining operations and deep open pit mines. These complexities and difficult geological environment introduce more uncertainties and simple empirical formulae would not be adequate as a design tool. These situations require numerical modelling and analysis of the design problems including interpretation of the results obtained from the analysis. There are several tools available for performing the numerical modelling and analysis. A brief review of the available tools was addressed earlier (Basu and Kuruppu, 1995). The authors selected ANSYS (a general purpose finite element analysis tool) for use in mining geomechanics and geotechnical design. This paper includes several examples demonstrating the applicability of this software in designing structures applicable to mining geomechnics. The authors hope that the design examples will demonstrate the use of the numerical modelling and analysis application in excavation design.

Jan 1, 1996

By J. K. Wilmshurst

Absorption, emission and reflection techniques for the study of [molten] inorganic materials at high temperatures have been critically examined. In general, the reflection technique is the most satisfactory for tine study of pure materials, while the absorption, and possibly also the emission techniques, may be useful for studies of certain dilute solutions. In the present investigation infrared emission spectra for sodium nitrate and silver chloride were obtained together with absorption spectra derived from reflectivity data by the method of Robinson and Price for sodium nitrate, silver chloride, lithium and potassium fluoride and their 1:2, 1:1 and 2:1 mixtures and for solutions of zirconium tetrafluoride in lithium-potassium fluoride (1:1) and sodium-potassium fluoride (1:1). It is concluded that vibrational spectroscopy cannot give unambiguous information concerning the existence of complex ions in fused salt, mixtures.

Jan 1, 1963

By H. Y. Sohn

Considering the two most important issues the ironmaking industry faces today, i.e., energy consumption and greenhouse gas emissions, it would be advantageous to utilize the concentrate-size raw materials directly without pelletizing or sintering, especially without the use of coke. This plenary lecture describes two such processes developed at the University of Utah. One is the Flash Ironmaking Technology (FIT) and the other is a moving-bed process for continuous ironmaking with gaseous reduction of iron ore concentrate (MBIT). These technologies are designed to produce iron directly from iron concentrate without requiring pelletization/sintering and cokemaking in two significantly different temperature ranges. They take advantage of the high reactivity of the concentrate particles and will considerably reduce energy consumption and carbon dioxide emissions compared with the current processes. The process of the development from the conception of the idea, to kinetic feasibility establishment, to laboratory flash furnace, and finally to the operation of a prototype facility for the development of the FIT is discussed. The development of the MBIT also started with the formulation of the process concept, followed by kinetics feasibility establishment, and the design of a potential industrial reactor. The results of economic analyses on the FIT are briefly described.

May 12, 2023