Search Documents

By L. Dison

This technical note is issued in two parts, as follows: Part I, after a brief introduction, discusses the value of patents and the law of patents, including patent applications and the exploitation of inventions. This is followed by some comments for the benefit of would-be inventors and potential users of patents. Part II, which will appear in the February issue of this Journal, focuses on the mining industry and then discusses views on patents that were Quoted in Part I. The last section makes recommendations as to how II1ventors and users (including mining authorities) should handle patents.

Jan 1, 1992

By M. C. Harris

Float-sink analysis has wide application in the coal laboratory. This paper evaluates the established methods used for the float-sink analysis of fine coal, and then describes a new method and apparatus that can be used for material down to a few micrometres in size. The method is rapid and accurate, and requires only a small amount of sample. The results presented show close agreement with the float-sink analyses obtained by the more classical technique using separating columns. The new centrifugal method reduces the time required for the analysis by a factor of ten.

Jan 1, 1986

By R. Rubin, P. A. Laxen, G. S. M. Becker

An account is given of developments in the use of activated carbon for the recovery of gold from cyanide solutions. The carbon-In-pulp process employed at the Homestake Mine is described, and its various applications in South Africa and their effectiveness are discussed. Probable future work on the carbon-in-pulp process and other possible applications of carbon for the recovery of gold are outlined.

Jan 1, 1979

By R. J. Mason

The paper discusses the claim that the remains of mines in Southern Africa date from ancient times, rather than from a more modern period. The evidence indicates that these mines were excavated by Iron Age Black people, who moved into South Africa from about A.D. 100 onwards. Details are given of the finds made in 1981 in an investigation of the remains of copper mines in the Dwarsberg, which probably date from the nineteenth century.

Jan 1, 1982

By A. A. Hazell

Mine management by objectives By A. A. HAZELL The author discusses the objective areas of mine management. Setting objectives is seen to be a conscious process which starts at the highest level of management. This enables clear objectives to be set at each lower management level. The methods of setting objectives in the areas of stope production, productivity and manager performance are set out in detail. In the area of manager performance emphasis must be placed on the practice of management. It is concluded from results obtained that "management by objectives" produces better than average perormances.

By B. C. Alberts

This. paper indicates how the South African Iron and Steel Industrial Corporation Limited (Iscor), as a major consumer of raw materials, determines the tonnage and quality of essential raw materials required to satisfy an increasing demand for steel and how this led to the establishment of a coal mine with a highly sophisticated beneficiation plant in the Waterberg coalfield, near Ellisras in the Transvaal. The planning of the project, with specific reference to the limited reserves of metallurgical coal in South Africa, the quality and quantity of the coal to be produced, and the way in which the project was managed is discussed briefly.

Jan 1, 1982

By J. H. Bulloch

A short review is given of the effects of corrosion fatigue on the materials used in pressurized water-reactor vessels. Selected topics such as testing procedures, test data, and mechanisms in simulated environments are discussed. The main fact that emerges is that most of the data on the growth of fatigue cracks reside below the ASME X1 1980 High-R 'Wet' design-code lines, Le. they fall within that specification. Finally, some recent advances in the understanding of the corrosion-fatigue behaviour of such materials in pressurized water reactors are highlighted.

Jan 1, 1987

By L. A. Vermeulen, C. P. Campbell, D. D. Howat

The production 01material liner than 75 µm in a number of open-circuit mills was investigated. The mils ranged from laboratory rod and ball mils treating a variety 01 ores to large industrial rod mils treating gold and copper ores. It was shown that the dependence on feed rate 01 the production 01 material liner than 751J.1T1 can be accurately described by a simple formula that was derived in previous work. In some 01 the systems reviewed, it proved possible to assess the feed rate 01 ore to the mil at which the rate 01 production 01 material finer than 75 µm can be maximized.

Jan 1, 1991

By R. D. Hancock

The complex responsible for the poisoning of anion-exchange resins is identified as the anionic cobaltic penta¬cyanide mono aquo species. It is shown that, at high concentration, this species polymerizes in solutions of pH less than 9. A mechanism for poisoning is presented that involves adsorption of anionic cobalt cyanide by a normal ion-exchange process, followed by polymerization within the resin matrix to form complexes that are too large to diffuse readily through the resin pores. The effects of resin structure and functionality on the extent of cobalt poisoning are examined, and the effect of cobalt poisoning on the kinetics and equilibrium loading of uranium is discussed.

Jan 1, 1979

By C. van Loggerenbergt, P. E. Ventert

A strong incentive exists for the coal-preparation engineer to improve plant efficiency by modifying circuits and upgrading process equipment, since these result in lower production costs and more valuable plant products. At the Grootegeluk Coal Mine, it was found that the overall plant efficiency could be improved by modifications to the dense-medium circuits, the installation of additional process equipment for the recovery of fine coal, and improvement of the fine-material processing circuit. Apart from these modifications, there is still potential to increase the plant efficiency, particularly in the utilization of plant waste, the recovery of slimes, and even the improvement of cycloning performance as a result of new cyclone design. This paper points to the potential wealth locked up in existing coal-preparation plants, and shows how the coal-preparation engineer, with new technology at his disposal, can unlock this wealth.

Jan 1, 1992

By P. V. Scheers

A rotating-cylinder electrode (RCE) was used to simulate the effect of flow velocity on pipe corrosion. A comparison is made between the electrochemical measurements obtained and those measured with a laboratory-scale flow loop. There is good general agreement if the speed of rotation of the RCE is adjusted to give the same value of mass transfer Coefficient as in the other system. Hence, it appears that the RCE is well suited to simulate actual flow conditions in pipes. The simultaneous effect of flow velocity and pH value on the corrosion rate of mild steel in a synthetic mine water was investigated. The i1nrease of corrosion rate was found to be more pronounced at lower pH values and, apart from a sharp increase below pH 4, the initial corrosion rate also increased at pH 7 and 6.

Jan 1, 1992

By R F. Sandenbergh, Y Wei

The flotation separation of the Rosh Pinah ore into lead and zinc concentrates are based on the selective flotation of the lead containing minerals followed by the activation and recovery of the zinc sulfides. In the present work the influence of the composition of the water on the selective flotation of the lead containing minerals is reviewed and the results given of the laboratory investigation of the influence of activating species such as silver, lead and copper, on the selective recovery of lead minerals from the Rosh Pinah ore. It was found that it was difficult to prevent the activation of the sphalerite by the metal species in solution in the absence of cyanide, and that colloidal precipitates most probably also serves as a significant carrier of these activators in the flotation circuit. Removal of heavy metal species from the solution by means of an adsorbent is possible, but most probably not practical.

Jan 1, 2007

By R. G. B. Pickering, H. H. Haase

Few innovations in the South African gold mining industry could have a more significant impact on improving profitability than non-explosive methods of mining. The far-reaching benefits of this approach are explained and the progress made through development work funded by the industry is described. Three methods are considered: impact ripping, sloting with abrasive waterjets and diamond saws, and breaking from drilled holes with waterguns and electric pulses. Of these methods, impact ripping is the most advanced and requires only minor refinements before production applications can be initiated. Although this method, based on current performance, is expected to yield considerably increased profits, it is predicted that it could perform several times better than at present with further development. The other methods of rockbreaking also show potential. Waterguns and electric rockbreaking would be attractive in unfractured rock for difficult geological conditions, and for confined areas such as gullies and development ends. Methods based on sloting could be combined with any of the other methods to enhance their effectiveness and thus yield further improvements in profitability; also, they could be used to advantage in specific applications. Al the discussed methods, therefore, deserve to be developed further.

Jan 1, 1991

By M. H. Moys

The capacity of grinding mills can be maximized by use of measurements of mill power and bearing pressures. The criterion is as follows. If the derivatives with respect to time of the power and bearing pressure signals have the same sign, the volume of the mill load is smaller than the optimum value; if they have different signs, the volume of the mill load is greater than the optimum value. Few attempts have been made to use measurements of bearing pressure in the estimation of absolute values for the parameters that define the state of the mill load (e.g, mass, volume, and dynamic angle of repose) because the bearing-pressure signal is a complex function of these and other parameters. This paper gives a mathematical model that relates bearing pressures to these parameters. The theoretical values obtained from this model are compared with experimental values, and it is concluded that the model constitutes a good description of experimental reality. If accurate measurements of the load supported by each bearing are available, the model can be used in the estimation of the mass of the load in the mill. If independent estimates of the volume of the load or the dynamic angle of repose are available, the other parameter can be estimated from measurements of the bearing loads.

Jan 1, 1980

By L. A. Vermeulen, D. D. Howat

New distribution functions are derived to describe the size distribution of grinding elements in ball mils. The formulations are based on the assumption that abrasive as well as impactive interactions occur during bal milling-an assumption that is supported by a large body of experimental evidence. It is shown that the functions can be used in the estimation of the magnitudes of abrasive and impactive components in the total rate of bal wear. The relative magnitudes of the wear components provide a basis for optimization of the chemical and metallurgical properties of the balls in a given milling situation. However, it is contended that these quantities are also useful indicators of the relative intensities of the abrasive and impactive interactions that are operative in the size reduction of mineral particles within ball mils. These quantities can be determined for any industrial ball mil, and their magnitudes provide practical guidelines for mil operation. The theory is used in an analysis of samples of ball charges from two industrial ball mils, and it is also applied to al the data on bal-size distributions found in the literature. The qualitative correlation between the calculated values of the wear components and the reported operating conditions is good for a variety of industrial ball mils, in conformity with the hypothesis that the relative magnitudes of the wear components are related to the milling conditions.

Jan 1, 1986

By L. C. Stilwell

The paper will place into perspective the contribution that platinum makes to the South African economy. It will use statistics from official sources, namely the Department of Minerals and Energy, the Department of Customs and Excise, the South African Reserve Bank and Statistics South Africa. Surprisingly few people are aware of these statistics, especially Supply and Usage tables, published by Statistics South Africa, and trade statistics, published by the Customs and Excise division of the South African Revenue Service. The paper will therefore contain a concise explanation of input-output tables and supply usage tables, as well as the derivation of gross domestic product and an outline of the System of National Accounts, of which Input-Output Tables and supply and usage tables are components. GDP is a commonly used, but poorly understood, measure of the wealth of an economy. The paper will explain the methods used by SSA to calculate this indicator and its place in the System of National Accounts (SNA). South Africa exports almost all its platinum production (87.5% in 2002). Exports are a final demand, as opposed to intermediate demand from secondary industries, and therefore do not enter the value-adding process, which is the essence of GDP. By definition, therefore, platinum on its own is not a major contributor to GDP. The platinum industry does, however, have an impact (known as the multiplier effect) on other sectors of the economy. The paper will explain the meaning and derivation of these multipliers, using a model based on an Inverse Leontief Matrix.

Jan 1, 2004

By D. R. Hardman

South Africa is the third-largest supplier of coal on the world's export markets after Australia and the USA, and the second-largest supplier of bituminous steam coal following Australia. There are many Similarities between the coal industries of South Africa and those of Australia and the USA, in contrast to the coal industries in Europe. For South Africa to maintain a competitive position on the export markets, it must continue to compete against these two countries. It is therefore important that the performance of the loca1 coal industry should against that of the Australian and US coal industries. Although financial performance is the major criterion, financial information is not easily obtained, and the paper therefore uses employee productivity in the form of tonnes per man year as a means of comparison. The paper reviews recent trends in the level of production and numbers of employees prior to review1ng the productivity. The influence on productivity of some mining methods is highlighted. It is realized that published information (information available within the public domain) can contain anomalies, but every effort is made to compare data of a similar type. Notwithstanding possible inaccuracies, it is shown that South African coal-De productivity lags far behind that of Australia and the USA. The significance of the difference is that the South African coal industry is able to apply overseas practices and procedures that have been shown to give improved performance, and that the increased use of more productive extraction techniques has limited application.

Jan 1, 1996

By M. L. Young, J. B. See

Effective thermal conductivities of packed beds of chromite ores by M. L. YOUNG, B.Se. (Rand), M.Sc. (Rand) (Visitor) and J. B. SEE, B.Sc. (Hons), Ph.D. (New South Wales), M.I.M., M.I.M.M. (Member) The effective thermal conductivities in stagnant air of packed beds of fines, lumps, and indurated and pre-reduced pellets of two chromite ores with different chromium-to-iron ratios were determined in the temperature range 300 to I 100°C by the heat-sink technique. Packed beds of fines, whether of the size fraction between 20 and 65 mesh, between 65 and 100 mesh, or between 100 and 150 mesh, were found to have the same values of effective thermal conductivity. For one ore, the effective thermal conductivities of packed beds of fines between 20 and 48 mesh at tem peratures above 600"C were higher than those for finer particles. This difference is explained as being due to the increase in importance of radiation heat transfer, but no definite conclusions are reached about the relative contributions of conduction and radiation heat transfer to the effective thermal conductivities of packed beds of fines between 20 and 48 mesh. Two published models were used for the theoretical prediction of values for thermal conductivities of the indurated and pre-reduced pellets as well as of lump ore. The experimental and theoretical results were in good agreement in view of the uncertainties in the assumed values of emissivity and thermal conductivity of the chromite ore.

Jan 12, 1976

By L. N. Stewart, H. L. Bovey

Since 1955 extensive pressure-leaching testwork has been conducted by Anglo American Research Laboratories (AARL) in laboratory-scale batch autoclaves. In 1958asmall continuous pilot-plantof45 kgofsolids per hourwas operated by AARL. In 1974, when high uranium prices were anticipated, Anglo American, encouraged by successful commercial- scale autoclave operations as practised by Outokumpu, Sherritt Gordon, and Impala Platinum, decided to install a continuous pilot plant at Western Deep Levels. At that time the proposed pilot plant was considered to be of prototype size. The project was funded by members of the Nuclear Fuels Corporation (Nufcor). Since its commissioning in February 1977, the pilot plant at Western Deep Levels, which can treat between 10 and 20 tons of dry solids per hour, has been used to test ores from four different mines. The paper compares the uranium extractions and pyrite oxidation obtained in laboratory batch autoclaves with those obtained in the continuous pilot plant. In general, differences in uranium extraction are not great and can be explained; the differences in pyrite oxidation are less well understood. The effect on plant design of the evolution of carbon dioxide during leaching is discussed. Evaluation of the equipment and materials of construction would have been almost impossible in a small-scale batch autoclave. It is doubtful whether such results would have generated the necessary confidence to permit decisions to install a commercial-size plant. The development and performance of the multistage pumps, instrumentation, shaft seals, and shaft-seal water treatment are discussed. It is concluded that the operation of a largescale continuous pressure-leaching pilot plant to supplement laboratory batch autoclave tests has been a necessary part of the development of this process.

Jan 1, 1979

By C. Ringas

Pipelines are used extensively in industry to convey various products. Internal corrosion of pipelines can lead to perforation and leakage of the product. A growing problem, not often accurately recognized, is internal corrosion of pipelines caused by bacteria. Microbiologically-induced corrosion (MIC) refers to corrosion caused by a variety of micro-organisms. This form of corrosion is not widely recognized in many industries, although it is widespread and causes many corrosion problems in pipelines, both internal and external. Sulphate-reducing bacteria (SRB) are responsible for the bulk of the corrosion problems caused by MIC. Corrosion caused by SRB is found extensively in water pipelines conveying raw, potable and waste water, as well as in pipelines conveying slurries. This problem also occurs in pipelines conveying crude oil. This paper describes internal corrosion problems of slurry pipelines caused by bacteria and outlines mitigation methods to improve slurry pipeline integrity, thereby extending the life of such pipelines.

Jan 1, 2007