Search Documents

By M. D. G. Salamon

In view of an urgent need for a simple means of simulating the behaviour of stratified rock masses, a long-dormant linear model is revived, generalized, and discussed in some depth. The model is piecewise homogeneous, consisting of a pile of homogeneous isotropic laminae in which the interfaces between beds are parallel and free of shear stresses and cohesion. The continuity of stresses and normal displacements is assured across the bedding planes and, to maintain simplicity, the theory of thin plates is used as the kernel of the model. The paper covers the case where the rock mass consists of discrete beds in which the layers are arranged either heterogeneously or systematically. The stratification is regarded as uniform when all the layers are of the same thickness and their Young's modulus changes exponentially with depth; and as homogeneous when all the laminae have identical thickness and properties. The case of uniform stratification is also treated on the basis of an equivalent quasi-continuum derived from the basic model. Attention is focused on the derivation of influence functions. It is demonstrated that the quasi-continuous models, when they are available, can replace their distinct-layer counterparts. The homogeneous quasi-continuum, which permits the derivation of its influence functions in closed form, facilitates the determination of the roof and floor convergence. In the case of a significant class of problems, the convergence distribution is defined by a second-order differential equation in the xy plane, which simplifies to a Poisson's equation if the mining excavations are unsupported. With this result, the paper prepares for the solution of a host of practical problems. These solutions are presented in a series of papers that are in the course of publication.

Jan 1, 1991

By H. E. Cross

The conversion of a uranium plant to the recovery of zinc by H. E. CROSS. B.Sc. (Eng.)(Hons.) Rand (Fellow) The conversion of the Vogelstruisbult Uranium Plant into a plant for the production of electrolytic zinc is described. The reasons for the conversion, the preliminary investigations. and the basic design principles are all outlined, and a brief account is given of operating experience.. during the commissioning of the plant, with equipment that had been put to a use for which it was not originally Intended.

Jan 11, 1973

By R. J. Davidson, N. Schoeman

SYNOPSIS The paper describes each of the stages in a carbon-in-pulp (CIP) or carbon-in-leach (CIL) plant, and details the steps that can be taken to achieve effective carbon management by referring to practices at the Daggafontein CIP plant. This approach was adopted because of the difficulty in summarizing current carbon management in the many varying operations in South Africa, Daggafontein being chosen as a high-tonnage dedicated well-run plant of recent design. Because of the major role played by the consumption of carbon in the operating costs of CIP and CIL plants, an attempt is made to develop a series of indexes based on quality parameters and price that can be used as a guide In the selection of carbon.

Jan 1, 1991

By R. Heunis

The hazard of rock bursts and rock falls as experienced in South African gold mines is examined in the light of recent research findings. The problem areas include high fatality rates, losses in production and equipment, and a detrimental influence on the recruitment of labour. The nature of the hazard is analysed, and it is shown that rock bursts are strongly related to the spatial rate of energy release by mining but that rock falls are not. The role of blasting and geological discontinuities is discussed. Practical rock-burst control strategies are compared, including the use of stabilizing pillars, back-filling and, in particular, techniques for reducing the frequency and severity of accidents resulting from large rock bursts. The latest stope-support experiments and their potential implications to mining are consid~red. It is concluded that a better understanding of the rock-burst and rock-fall hazard has resulted from the industry's research efforts. The findings can be applied towards obtaining an improved underground environment for men and machines.

Jan 1, 1980

By M. J. A. Leal-Gomes

There is a set of settled ideas in the field of the mechanics of rock mass joints, that need a deep revision, after the last experimental works of several authors. In this paper, this theme is approached under several viewpoints, like the following ones: the essential influence of the mating or mismatching of rock joints on their strength (different strength models are applicable to these two situations, one leading preferably to normal scale effects, and the other to inverse scale effects); Patton's model is a bad formulation of the joint strength, whenever there is a dilation effect in the slidings (actually, the essential consideration of the amplitude of the roughess isn't made by any limit equilibrium model, like Patton's model); the joint strength increases as the width perpendicular to the sliding direction is reduced (previous works of other authors suggested the independence of the strength on that width); the reduction of the anisotropy of the roughness, as the sample symmetry and sample dimensions increase; there is no scale effect in the discontinuity mechanics, if there is no roughness heterogeneity; when only the same roughness and undulation orders are involved in the tests, shorter samples have larger peak displacements and lower shear stiffnesses than larger samples (usually, the contrary is admitted). For all these reasons, there isn't an easy correlation between the small scale tests and the natural large joint scale. Only "in situ" large scale tests have some representativeness. All the above mentioned questions are correlated to each other. Es gibt eine Menge eingewurzelter Ideen im Gebiet der Mechanik von Felsklüften, die, nach den letzten experimentellen Arbeiten von mehreren Verfassern, eine tiefe Überprüfung benötigen. In dieser Mitteilung, wird dieses Thema unter mehreren Blickpunkten angegangen, wie die folgenden: der wesentliche Einfluß des Zusammenpassens oder nicht Zusammenpassens von Gesteinsklüften auf ihre Festigkeit (verschiedene Festigkeitsmodelle sind auf diese zwei Situationen anwendbar, eins, das vorzugsweise zu normalen Maßstabseffekten führt, und das andere, das zu umgekehrten Maßstabseffekten führt); Pattons Modell ist eine schlechte Formulierung der Kluftfestigkeit, immer wenn es einen Dilatationseffekt in den Verschiebungen gibt (in Wahrheit, wird die wesentliche Berücksichtigung der Rauheitsamplitude von keinem Grenzgleichgewichtsmodell beachtet, wie Pattons Modell); die Kluftfestigkeit wächst wenn sich die Breite senkrecht zur Verschiebungsrichtung verringert (frühere Arbeiten anderer Verfasser suggerierten die Unabhängigkeit der Festigkeit von jener Breite); die Verringerung der Rauheitsanisotropìe, wenn die Probekörpersymmetrie und Probekörperabmessungen zunehmen; es gibt keinen Maßstabseffekt auf die Trennflächenmechanik, wenn es keine Rauhheitsheterogenität gibt; wenn nur die gleichen Rauheits- und Ondulationsgrößenordnungen in den Versuchen verwickelt sind, haben kürzere Probekörper größere Spitzenverschiebungen und geringere Schersteifigkeiten als größere Probekörper (gewöhnlich, wird das Gegenteil angenommen). Wegen aller dieser Gründe, gibt es keine einfache Korrelation zwischen den Versuchen im kleinen Maßstab und dem natürlichen großen Kluftmaßstab. Nur "in situ" Versuche im großen Maßstab sind einigermaßen repräsentativ. Alle die oben erwähnten Fragen hängen miteinander zusammen. Il y a un ensemble de des bien établies arrière-pensées idées dans le champ de la mécanique des discontinuités en massifs rocheux qui ont besoin d'une profonde revision, après les derniers travaux de divers auteurs. Dans cet article cette matière est abordée sous divers points de vue, comme les suivants: la signification essentiel de l'ajustement ou du désajustement des discontinuités dans leur résistance. Des différents modèles sont applicables à ces deux situations, une conduisant de préference à des effets d'échelle normaux et l'autre à des effets d'échelle inverses; le modèle de Patton est une mauvaise formulation de la résistance des joints quand il y a effet dilatant dans les glissement. En effet la contribuition essentielle de l'amplitude de la rugosité n'est pas consideré par aucun modèle d'équilibre limite comme le modèle de Patton; la résistance des joints croit au fur et à mesure que la largueur perpendiculaire à la direction de glissement est réduite. Des travaux antérieurs d'autres auteurs suggéraient que la résistance était indépendant de cette largueur; la réduction de l'anisotropie de rugosité au fur et à mesure que la symétrie et les

Jan 1, 2003

By J. P. G. Pretorius

The size effect in tests of the compressive strength of coal specimens differs from predictions based on the Weakest Link theory. Predictions of the size effect in tensile tests on lengths of cotton yarn and glass fibre, the behaviour of which is analogous to the weak link process, also differ from observations. This discrepancy is shown to be caused by the correlation between the strengths of the unit lengths in a composite specimen. The Weakest Link theory is reformulated as the Weakness Correlation theory to account for such correlation. It is shown that weakness correlation is found in rock and it is concluded that at least part of the discrepancy between the predicted and observed size effect in rock strength tests could be attributed to this correlation.

By J. A. Ryder

A high proportion of damaging rockbursts are thought to be underlain by seismic events that represent shear or rupture along planes of weakness (faults, joints, dyke contacts). Such events are controlled by shear stresses and friction properties along the plane. Excess shear stress (ESS) is a measure that can be evaluated numerically and that, in principle, can be used in an assessment of the possible magnitude and relative likelihood of seismic activity. Methods for the calculation of ESS in practical mining contexts, and for the estimation of the magnitudes of possible seismic event progressions, are briefly reviewed. The effects of variables such as depth, stoping width and, in particular, virgin horizontal stresses on general shear-type seismic hazards are investigated. Attempted back-analyses of two large rockbursts are described.

Jan 1, 1988

By Lene Hansen

Sulphuric acid plants now and then see unexpected increases in SO2 emissions. Our experience is that it is not always easy for the acid plants to pin point the exact reason for the SO2 increase. Sometimes a catalyst bed is sacrificed even though reliable emperature readings and gas analyses could have verified satisfactory activity, hence the leaking heat exchanger is never discovered and after the shutdown the SO2 emissions are still too high. This paper will look into some basic catalyst management tools: Good record keeping is a necessity for collection of representative catalyst samples, reliable operating data is an inevitable starting point for all analysis and trending of operating data is a must for plant optimisation and troubleshooting. In addition these catalyst management tools will give a continuous updated knowledge of the catalyst status in each bed providing the basis for a more effective replacement strategy. The most typical reasons for increasing SO2 emissions will be presented together with easy guidelines for cross-checking of operating data, temperature optimisation and good record keeping.

Jan 1, 2009

By C. Chongo, F. X. Paquot, C. Ngulube

"Over the last six years, the Kansanshi copper-gold mine has continued to process significant quantities of complex transitional mixed ores. Initially, the ore treated came predominantly from accumulated stockpiles. Subsequently, the feed source shifted primarily to freshly mined ore that generally showed less tarnish with better flotation kinetics, but with the downside of lower concentrate grades. A number of changes were made to improve the efficiency of the rougher circuit and quality of concentrate produced. These changes were as a result of initial mineralogical studies and laboratory flotation test work that were discussed at length in a previous paper1. Salient among the recommendations adopted as a result of previous work were increased circuit capacity and a modified configuration to increase the residence time and the number of sulphidization stages. These modifications were completed and commissioned in 2011. This, however, resulted in significantly low rougher concentrate grades and a below-specification final concentrate product. This was due primarily to higher mass pulls from the extended rougher bank with multiple concentrate discharge streams, and which necessitated an enlarged cleaning capability. The extra cleaning capacity came on stream in 2014. Of note was the development of a recovery model, based on the strong correlation between the total copper and acid-soluble copper ratio, as a tool for monitoring plant performance. IntroductionThe Kansanshi mine, the largest copper mine in Africa, is 80% owned by Kansanshi Mining plc, a subsidiary of First Quantum Minerals. The remaining 20% is owned by the state through the parastatal Zambia Consolidated Copper Mines Ltd (ZCCM). The mine is located approximately 10 km north of the town of Solwezi and 180 km to the northwest of the Copperbelt town of Chingola. The mine has been in commercial operation since 2005."

Jan 1, 2016

Measurements of the rates of penetration at various throttle air pressures are presented as a function of thrust for three different rockdrills when drilling quartzites with strengths of 45 000 lb/in2 and 39 000 lb/in2, The rate of penetration at optimum thrust is shown to agree well with the predictions of theory and curves of air consumption as a function of throttle air pressure are presented. Man-held machines are shown to be under-thrusted at throttle air pressures above 40 lb/in2g. Measurements of bit wear as a function of distance drilled are presented graphically and discussed in terms of the theory developed in Part 1.

By C. Dechert, J. Norwood

Compañia Minera Antamina, Peru has recently completed a fifth year of operation of their 301-km concentrate pipeline. The pipeline was commissioned by PSI in May of 2001. The Antamina pipeline is generally accepted as one of the most complex slurry pipeline operations worldwide. The pipeline transports an average of 1.6 million tonnes of copper and zinc concentrates from the Yanacancha mine site at an elevation of 4 155 metres above sea level (masl) to the port of Huarmey at an elevation of 62 masl. Currently ten different types of concentrates are being transported as separate batches. The pipeline traverses oneof the most rugged areas in the world. It utilizes three different pipe diameters, and four remote valve stations to optimize the hydraulic design. PSI has recently completed an overall operational audi tof the Antamina pipeline. This paper evaluates the operational effectiveness of specific design features and operating philosophies, implemented during the engineering phase, over the last five years of operation.

Jan 1, 2007

By M. W. Hildyard, J. A. L. Napier

The improved design of support systems and stoping strategies when changes in depth, stratigraphy, or mine layouts are considered must rely on the designer's fundamental understanding of the deformation mechanisms adjacent to underground openings so that he can extrapolate and predict expected mining conditions. This paper presents a numerical approach to the modeling of the growth and interaction of mining-induced fractures near the edges of deep tabular excavations in brittle rock. Fractures are represented by displacement-discontinuity elements that are allowed to propagate according to prescribed growth rules. This procedure is justified by the reproduction of several features observed in laboratory simulations of fracturing around openings in blocks of rock subjected to uniaxial and biaxial compression. An attempt is then made to explain some of the attributes of the fracture zone surrounding tabular stopes. Particular questions of interest are the sequence in which fractures form and are mobilized in front of the mining face, the effect of parting planes parallel to the plane of the excavation, and the distribution of stress parallel to the hangingwall and footwall.

Jan 1, 1992

By D. D. Howat, J. van der Colf

This paper is the first in a series of three dealing with this subject and also with the rate of oxygen removal from the slags in the presence of solid carbon and with the physicochemical properties of the reduced slags. For selected members of the system, the melting temperatures and primary crystallization products were determined. as were the viscosity and the electrical resistivity of the corresponding melts. All the experiments were conducted in a neutral atmosphere. Where determined, the primary phase was found to be either perovskite or magnesium aluminium titanate. The composition variable exerting the most pronounced influence on viscosity or resistivity was found to be the basicity expressed as the mass ratio (CaO + MgO)jSiO,. The ratio CaOjMgO became important only at Iow basi<:ity values. Although generally there is a direct proportionality between log (viscosity) and log (resistivity), slags h&apos;lving either a very high silica content or a very high titania content have anomalously Iow electrical resistance.

Jan 1, 1979

By N. C. Joughin, A. C. Buckmaster

The use of face conveyors in gold mines by N. C. JOUGHIN. B.Sc. (Eng.). Ph.D. (Wits) (Member) and A. C. BUCKMASTER; M.A. (Cantab.) A mechanized stope-cleaning system has been developed around an armoured face conveyor, which was tested on the surface and in two underground trials. In the second underground trial, an average face advance of 8,5 m per month was obtained with a labour productivity of 27 ca/worker/month on a two-shift blast cycle. Two new face cleaning systems have been built, each incorporating an armoured face conveyor, a loading plough, a collapsible self-advancing barricade, and an integral roof-support system. These are about to be tested. A new type of reciprocating flight conveyor is being developed for stope use. This is cheaper, lighter, and more compact, and exhibits better wear characteristics, than an armoured face conveyor. In the early stages of the trials, this conveyor frequently achieved a singleshift blast cycle. It should be possible to achieve face advances of up to 40 ca/worker/month with a consistent one-shift blast cycle. The use of drill rigs and a self-advancing roof-support system would improve the productivity to over 50 ca/worker/month.

Jan 2, 1976

By S. L. Crouch

This paper describes a numerical procedure for the computation of the displacements and stresses induced by the mining of a tabular ore deposit in faulted ground. The numerical procedure is based on the displacement discontinuity method, which can be regarded as an application of Salamon&apos;s &apos;face element principle&apos; to cases in which the reef plane is faulted into several sections, or even folded in an arbitrary way. An element of a fault is modelled in the same manner as an element of the reef, except that a fault element is allowed to undergo permanent inelastic deformation (i.e., slip) if the stresses transmitted through the fault-filling material satisfy a Mohr-Coulomb yield condition. An iterative technique for the incorporation of a Mohr-Coulomb yield condition in the general displacement discontinuity method is explained. This technique is illustrated by means of a simple example involving the mining of a flat-lying reef intersected by a fault. The displacements and stresses at selected locations along the fault are examined as the reef is mined, element by element. A consideration of the energy changes reveals that the occurrence of slip along a fault leads to a sudden increase in the energy release rate due to mining as the excavation intersects the fault. The energy release rate then falls off abruptly to a value less than that which would occur in the absence of any slip, and gradually builds up to re-establish the conditions that would exist in unfaulted ground.

Jan 1, 1979

By T. T. Matuludi

Kleinkopje Colliery has five Wemco drums that were installed and commissioned in 1978. Over the years, there have been remarkable changes in mining and geological conditions at the colliery. First, an increase in the percentage of fines was recorded, which resulted in an uneven split or an imbalance in silo levels between material feeding the cyclone (-12 mm) and Wemco drum (+12 mm) sections respectively. This problem was solved by doing modifications around the banana screens to allow finer material to the drums. The imbalance challenge was then followed by spontaneous combustion that takes place in situ and results in low product yield. The results obtained from efficiency tests indicate that although there is a limit in the percentage of -6 mm material in the feed, Wemco drums are still very efficient and applicable to the current mining conditions. These results also suggest that it is essential to lower the throughput when the drums are treating low yielding coal.

Jan 1, 2010

By D. G. Krige

Some basic considerations in the application of geostatistics to the valuation of ore in South African gold mines by D. G. KRIGE, Pr. Eng., D.Se. (Eng.) Rand (Fellow) There is much room for improvement in the statistical procedures that have been used by gold mines over the past decade in the valuation of their ore reserves. Improvement depends on the establishment of the extent to which the patterns of frequency distributions and the directional variograms for the gold values vary from area to area within each section of a mine. The application of the lognormal distribution and of the De Wijsian variogram model for routine ore-reserve valuations requires detailed study before some of the reservations still held by mathematical statisticians can be met. This paper provides some preliminary evidence of the extent to which these models can be used with confidence, as well as suggesting how they can be applied to their full potential.

Jan 4, 1976

By S. M. Spottiswoode, A. J. Jager, N. C. Gay, J. A. Ryder

The South African mining industry is at present planning to extract orebodies at depths of up to 4 km. To do this cost effectively and, at the same time, ensure safe working conditions for mining, the personnel will require both the development of new strategies and the implementation of current rock-engineering technological developments on a wide scale. This paper covers most of the technological developments likely to be required for mining at very high stresses, but it is clear that improved regional support systems will need to be developed to ensure defective stability of the rockmass during mining operations. Similarly, it is clear that improved strategies for mining in large-scale geologically disturbed areas, where slip on faults or dykes can result in wide-spread rockburst damage, will have to be addressed

Jan 1, 1995

The kinetics of adsorption of gold di-cyanide onto activated carbon has been investigated extensively over the past two decades. These studies have demonstrated that both film and intra-particle mass transfer affect the kinetics. The dominant mechanism of intra-particle mass transfer has not yet been identified. In the work described, surface diffusion and pore diffusion are considered as possible rate-determining mechanisms of intra-particle mass transfer. Mathematical models are described that incorporate film mass transfer and the respective intra-particle mass transfer mechanism with equilibrium described by a Freundlich isotherm. Rate constants of film mass transfer and pore or surface diffusivities were estimated by the fitting of the respective models to experimental carbon adsorption data. The estimated pore diffusivities, after they had been corrected for the porosity and tortuosity of the carbon, were found in most instances to be higher than the molecular diffusivity of dilute gold di-cyanide in aqueous solution. This situation is not physically viable. The surface diffusion mechanism acting in parallel with the pore-diffusion mechanism is thus responsible for the intra-particle transportation of most of the gold.

Jan 1, 1996

By P V. Savage, T Glück, RCA Minnitt, C Bothma

Manganese Metal Operations ?Manganese Metal Company (MMC), a subsidiary of Samancor BHP Billiton, has two production facilities for electrolytic manganese metal in South Africa and produces a range of about 44 Mn metal products. ?The company is accredited with ISO 9000 and uses Six SigmaTM for continuous improvement. ?The control of the process relies on the effective functioning of approximately 250 different control loops at 50% automation.. ?Approximately 50000 samples are analysed every month. ?There are pyro, hydro and physical unit operations for the production of electrolytic manganese metal flake and value added products ? [ ]

Jan 1, 2005