Search Documents

By G. C. Lindeque

"A downward trend in tyre life on haul trucks at an open pit iron ore mine prompted an investigation into the current tyre management strategy in order to improve tyre life. ‘Best practice’ was compared to the current tyre management strategy at the mine to determine aspects that could be improved. Aspects that showed significant room for improvement included employee tyre awareness, tyre pressure maintenance, and road conditions. For each of these aspects a plausible alternative was suggested.A new tyre management strategy was formulated as a step-by-step guide on how to implement the proposed changes. Each step introduces new initiatives but at the same time builds on the previous step’s success. A sensitivity analyses was performed to determine the impact of the proposed changes, with the variables being the reduction in the percentage of premature tyre failure, and the reduction of the site wear rate.The ‘most likely’ scenario showed an increase in tyre life of 41% for the Komatsu 730 trucks and 105% for the CAT 777 trucks if the entire tyre management model is implemented. This would result in a possible annual saving related to tyre usage of R9.2 million. OverviewThe study focused on the tyre life on the main haul fleet at an open pit iron ore mine. The haul fleet consisted of 17 Komatsu 730 (180 t) haul trucks and 12 CAT 777 (90 t) haul trucks.The haulage operation consists entirely of tyre-based haul trucks. Five per cent of the total mining budget is related to tyre costs. Since 2012 there has been a steady decrease in tyre life as measured in operating hours (Figure 1) due to the high percentage of tyres that fail prematurely. In 2014 a total of 41% of all tyres failed prematurely and 61% were classified as ‘worn out’."

Jan 1, 2016

By N. du Preez, J. Christie, F. Crundwell

Precipitation is a key process in the recovery of copper and cobalt. While there is a wealth of experience in operating precipitation steps, improving their performance remains challenging. Chemically, the reaction might be controlled by reaction kinetics, be limited by oxygen mass transfer, or be at equilibrium. In this paper, we examine these different operating regimes and demonstrate how they can be identified from plant operating data, process modelling, and pilot plant test work

Jan 1, 2023

Review Mining annual review June 1979. London, Mining Journal, 1979. 624 pp. Available as part of the subscription to the Mining Journal or at £12,50 per copy. This annual review is recognized internationally as the world leader in reporting on metals and minerals, and is eagerly awaited each year for its authoritative content, which is compiled by well-respected experts throughout the world.

Jan 1, 1979

By R. T. Muller

Contribution to the above paper by R. T. Muller (Visitor) Demands are being made and pressure is being brought to bear on employers in South Africa to narrow or eliminate the wage gap between their White and Black employees. Few thinking people will dispute the fact that a constant improvement in the wages of Black personnel is essential, but this cannot be done merely by a redistribution of income in South Africa.

Jan 7, 1974

By A. A. Bradley, P. J. D. Lloyd, A. J. Freemantle

Developments in centrifugal milling by A. A. BRADLEY,B.Sc. (Rhodes) (Visitor), A. J. FREEMANTLE, B.Sc. Hons. (Wits) (Visitor), and P. J. D. LLOYD, B.Sc. (Chem. Eng.), Ph.D. (Cape) (Fellow) The theoretical and experimental results of a study of centrifugalmills are reviewed. Means for the scaling up of such mills are suggested, and tests on a prototype mill are described. Despite the high lining wear in the centrifugal machine, which reduces its productive availability, its other advantages suggest that there is merit in pursuing its further development.

Jan 6, 1974

By I. Soto, E. Córdova, A. Anani

The new caving megaprojects that are planned to go into production in the next decade have scheduled horizontal developments at very high rates, which are difficult to achieve. Research has been conducted that seeks to model the construction times for underground developments to determine the feasibility of achieving the planned rates. However, these previous attempts do not consider all the operational aspects that make up the mine development cycle. Here, we present a discrete event simulation (DES) model that individualizes each unit operation of the development cycle to determine the construction rates that new projects will be able to attain. The developed model was applied to the New Mine Level (NML) of the El Teniente Division (DET). The results indicate that it would be impractical to achieve the advance rates scheduled in the original plans if the unit operations of the mine continue to be executed using the status quo. The metres developed after six years in the sections analysed can be significantly improved by changing the maintenance strategy for the equipment (457 metres increase), orepass availability (194 metres increase), and the initial planning sequence (1 598 metres increase). It is recommended that the mine implements a flexible maintenance strategy, defines a strategy to ensure and increase orepass availability to contractors, and makes use of current simulation tools for a more robust development sequence planning.

Oct 1, 2022

By T. M. Russell

"Face mapping is a simple but invaluable means of geological and geotechnical data acquisition whereby intact rock properties, rock mass properties, discontinuity properties, and structural orientation can be assessed. Although traditionally done via direct contact with the mapping face through techniques such as line mapping or window mapping, remote face mapping using various digital techniques has become increasingly popular in recent years. Sishen is a large open pit mining operation requiring a comprehensive geotechnical data-set to evaluate pit wall design and stability with the necessary level of confidence. Geotechnical borehole data, face mapping data, geotechnical laboratory testing data, and implicit structural models provide the main sources of this information. Although a large geotechnical borehole database has always been maintained at the mine, face mapping has in the past been restricted to sporadic and isolated stability assessments. In 2013 the mine acquired a terrestrial laser scanner with the resolution, photographic capabilities, and software required to carry out geotechnical face mapping. A face mapping procedure was set up based on accepted face mapping methods, the data requirements of the mine, and capabilities of the laser scanner system. Mapping data obtained from the scans was integrated into the Acquire geological data management system, a purpose-designed structured query language (SQL) database system used for storing the mine’s geotechnical data. Within the geotechnical design process, having face mapping data available has improved confidence in the properties of the rock mass and structural environment, allowing for better definition of geotechnical design sectors. Overall, the face mapping and geotechnical analysis features of the terrestrial laser scanner in use make it an invaluable geotechnical data capture tool, provided a system is in place to store mapping data in a manner that allows for meaningful rock mass and structural information to be produced. IntroductionFundamental to the geotechnical design process is the acquisition of a reliable and complete geotechnical data-set. Geotechnical data acquisition will typically commence during the early stages of a project and continue well into the operational life of the mine, with the data confidence progressively increasing as the amount of data captured increases. Sishen mine currently bases all open pit geotechnical designs and geotechnical risk assessment on geotechnical borehole data in conjunction with interpreted structural models. Boreholes are logged and the data is captured in an ongoing process. This process forms the initial step in the geotechnical design and risk assessment process whereby the raw data is used to classify the strength properties for each lithology, provide inputs for geotechnical block models, and ultimately provide the inputs for slope design analyses. To date, borehole data has provided the only largescale, organized data-set for input into geotechnical analyses at Sishen. Although borehole data is the best and most comprehensive form of geotechnical data, there are some shortfalls that can be addressed by other data collection methods. These shortfalls are as follows."

Jan 1, 2018

10th COMMONWEALTH MINING AND METALLURGICAL CONGRESS-CANADA, 1974 The Commonwealth Council of Mining and Metallurgical Institutions has received and accepted an invitation from The Canadian Institute of Mining and Metallurgy for the 10th Commonwealth Mining and Metallurgical Congress to be convened in Canada in April, 1974, immediately following the Annual General Meeting of The Canadian Institute of Mining and Metallurgy. It is proposed that the Congress centre will be Montreal and that, after technical sessions, tours of operations will be arranged. Further information will be issued in due course by The Canadian Institute of Mining and Metallurgy and enquiries should be addressed to the Executive Director of the Institute, 906-1117 Ste. Catherine Street West, Montreal 110, P. Quebec. NOTICE TO ALL STUDENT MEMBERS OF THE SOUTH AFRICAN INSTITUTE OF MINING AND METALLURGY The Institute offers each year for competition among Student Members of the Institute a prize, or prizes, should entries so warrant it, of up to the value of R100 to be awarded to the Student Member or Members who submit the best paper or dissertation on a topic appropriate to the interests of the Institute. In the case of Student Members who are in full time study at a university the dissertation or thesis which they may have to write in part fulfilment of their university curriculum may be accepted provided it is presented in a manner and on a topic suitable for publication in the Journal. The closing date for the receipt of papers shall be 31st December each year.

By C. J. Lenz

The results of prospecting operations involving geological data and a large number of geochemical determinations of the metal content of soil samples are plotted and evaluated by computer. Anomalous areas are identified in each type of environment by selecting probability or population boundary values from frequency distributions. The anomalies are plotted to permit correlation with geographical or geological features. Ranking of prospecting targets is made using geographic pattern, geology, absolute value and metal ratios. Three short case histories are presented.

Jan 1, 2014

By J. Rabe

Tasked with developing a flow sheet for a new resource, one typically turns the experts for help. The advice of an expert can be invaluable in reducing the time and costs associated with characterizing an ore (not to mention extracting maximum information from limited samples). While guiding and optimizing a metallurgical concept study requires a certain skill set, selling a project is something different. The metallurgical specialist is usually not responsible for sharing the results of investigations with potential investors. However, the person responsible for selling the project can ensure that a metallurgical concept study is conducted thoroughly and responsibly without having the ability to do the work, while being sufficiently familiar with the metallurgical aspects to authoritatively sell the project. The process of identifying suitable process routes through to constructing a concept flow sheet and mass balance is discussed as a basic example. From basic mineralogical information and a thorough literature survey, the most likely beneficiation routes can be identified and targeted testing conducted. The final top size will depend on the required product properties (mainly grade), the selected beneficiation technology, and the ore?s liberation properties. Once the required top size has been identified, comminution options can be evaluated. Once again, literature surveys can be used to supplement concept-level comminution property information, and select possible equipment and circuit configurations. Marketing, material handling, and logistics-related information can be used to determine required dewatering technologies. At this stage, enough information is available to develop a concept mass balance and conduct basic equipment sizing..

Jan 1, 2014

By R. Van Deventer

The BIOX® process was developed for the biological pre-treatment of refractory gold ores and concentrates ahead of conventional cyanide leach gold recovery. Rights to the process are currently with BIOMIN Technologies SA, a subsidiary of Gold Fields Limited. There are currently eight operating installations worldwide employing the process on a commercial scale. EKATO is a company specializing in developing new or optimizing existing mixing applications. EKATO has acquired a vast amount of expertise in agitation over its 75 year history. In a joint research project the reactors of the BIOX® process were characterized from the aspect of their mixing performance. BIOMIN is constantly testing new mixing solutions and reviewing potential vendors to increase the efficiency of the BIOX® process. EKATO?s intention was to qualify as an approved vendor for supplying agitation equipment to the BIOX® process. A two step approach was planned: In phase one of the project EKATO would develop an alternative agitation solution to the established option, exhibiting at least similar performance levels. In phase two potential possibilities to improve the overall design would be developed. This paper focuses on phase one and addresses the systematic approach applied by EKATO in characterizing the mixing processes. Mixing tasks were assessed individually applying basic theory and scale-up and -down rules to the individual tasks. Testing with model systems was done at the EKATO technology center in Schopfheim, Germany, on scales of 50 liters and 1 m³. The results showed that the ISOJET-B impeller design showed promising performance under BIOX® reactor conditions. Scale-up with the ISOJET-B was done in order to apply it in the 21 m³ live volume test reactor at Fairview mine in South Africa. At Fairview tests were performed using model systems and eventually under real plant conditions with BIOX® slurries. The results were a success and confirmed that the scale-up factors determined during the testing at EKATO?s technology center could be substantiated in the ?model scale? 25 m³ reactor. Testing under the actual process conditions showed that all design parameters were within the desired range to be considered an excellent leaching performance. This successful joint development shows the importance of a close cooperation of technology licensors or end-users and equipment suppliers. It is vital for understanding all factors influencing the mixing performance of processes. Exercises such as this will provide equipment suppliers and plant operators more confidence in managing further scale ups at ever larger engineered plants.

Jan 1, 2009

By Stephen Hughes

Ausmelt Top Submerged Lancing (TSL) Technology has gained widespread commercial acceptance in the lead and zinc industries, as an efficient and highly flexible pyrometallurgical reactor with accompanying excellent environmental performance. For the processing of lead and zinc bearing feed materials twenty one (21) Ausmelt furnaces are now in operation, under design or under construction. With recent increases in the value of both lead and zinc and an ever increasing focus on the sustainable use of resources, interest in the processing of secondary feed material sources as well as metal containing residues has substantially increased. Ausmelt Technology has proven to be well suited to the economic recovery of values from such sources. This has for example culminated in Ausmelt?s commitment to the Whyalla Zinc project as the owner/operator of a facility for the treatment of zinc bearing secondary feeds. This paper describes Ausmelt?s recent developments in the fields of lead and zinc processing, as well as further investigations into new processing areas, including the direct smelting of zinc concentrates. Ausmelt?s TSL Technology can now be regarded as Best Available Technology (BAT) for metal production.

Jan 1, 2008

By P. Hand

Most coal plants must run under conditions of varying feed conditions or are asked to produce qualities different from that used in the design. This can cause overloaded conditions as the ?bottlenecks? within the plant, depending on plant operation or as the feed changes. During plant design, geological information can be used to determine washability envelopes and blends that may be expected. Historical data can also be used to develop a size distribution envelope as well as to assign reasonable models for each of the unit processes. In operation, a plant can be sampled to determine changes and to refine process models. The information obtained can then be used in an accurate simulation to define how the plant can deal with the changing environment. This paper uses Limn: The Flowsheet Processor to simulate the coal plant in detail and will produce an accurate model, in terms of equipment sizing as well as water, medium, and solids balance, for each change in feed condition. It will show examples of running the simulation through complete density and size ranges and will determine the equipment required to address each part of the performance envelope.

Jan 1, 2010

By M. Pierce, E. Karampinos

"One of the main challenges in the numerical modelling of ground support in underground excavations is to reproduce the performance of the sequential installation of the reinforcement while capturing the rock mass behaviour of an advancing face in 3D. The 3D modelling approaches used to simulate the progressive advance of excavations are mostly continuum and often cannot reproduce the rock mass failure mechanisms. The 3D discrete element method (DEM) can better reproduce structurally controlled rock mass failure mechanisms and can explicitly represent the reinforcement elements. This paper builds on previous work that reproduced the structurally controlled squeezing conditions in an underground hard-rock mine using 3D DEM and the in situ behaviour of reinforcement under pull conditions. It addresses important issues on the way reinforcement is explicitly introduced in discrete element models. A pseudo-3D model is employed to overcome the computational restrictions and time limitations of a 3D modelling approach. The work focuses on the scaling of the material properties of the ground support elements when the thickness of the model is not equal to the out-of-plane spacing of reinforcement. It demonstrates the scaling methodology based on the type of the modelled reinforcement elements used and investigates the significance of this approach. The advantages and disadvantages of this approach with respect to 2D and 3D methods are discussed. The results are compared with field data and previous modelling work done at the mine. IntroductionNumerical models can provide significant insight into the anticipated behaviour of underground excavations. The modelling of ground support, however, is not a trivial exercise. An effective representation of ground support in underground excavations should capture the behaviour of both the rock mass and the support elements. When numerical models are used for design purposes, the complexity of the problem requires significant time and expertise (Sweby, Dight, and Potvin, 2016).At a laboratory scale, numerical models have successfully reproduced the results of laboratory tests on rockbolts by explicit modelling of the bolt, the borehole, and the grout. Chen and Li (2015) used a continuum FLAC3D (Itasca Consulting Group Inc., 2012) model to simulate the mechanical behaviour of D-bolts as observed experimentally. Grasselli (2005) used a 3D finite element code to model the behaviour of fully grouted rods and expandable bolts under shear."

Dec 1, 2018

A project was funded by the Australian coal industry to investigate the mechanisms that might lead to sample bias when using cross-belt cutters, in order to help coal industry personnel to make better decisions about the purchase, maintenance and operation. It concentrated on DEM modelling of skew cutters. These are set at an angle to the belt with the intention of minimizing disturbance to the non-sampled material. Two bias mechanisms are likely to cause bias for cross-belt cutters. Waves of material are bulldozed off the belt by the upstream side of the body of square cutters and material is thrown by the leading edges of cutter blades for all types of cross-belt cutters. These mechanisms cause some parts of the load of material on a belt to be over-represented. The effects of these mechanisms cannot be made to be negligible, so cross-belt samplers cannot be trusted to produce unbiased samples, especially for segregated streams of material. However, it is possible to give a bound on the maximum likely bias. The grades of two portions of the stream can be estimated by stopping the belt and shovelling off 1/3 of the cross-section of the load on the belt into a container, concentrating on the final side of the belt and the top of the load. The remaining material should be put into another container and the difference in grade determined. The maximum likely bias is typically about 10% of this difference. For a cross-belt cutter, having an extraction ratio near to 100% is not a reliable indication that the cutter has little or no bias. Some bias mechanisms affecting cross-belt sample cutters make sample mass too high and some make it too low, so an extraction ratio near 100% can occur if two bias mechanisms are both active. Keywords: sampling, DEM simulation, sample bias, accuracy, precision

Jan 1, 2009

Notices TRANSPORTATION AND THE ENVIRO NMENT The 5th Quinquennial Convention of the S.A. Institution of Civil Engineers will take place at the Carlton Centre, Johannesburg, from 20th to 24th August, 1973. ENVIRONMENTAL ENGINEERING A conference on environmental engineering problems in industrialized and developing countries is to be held at the United Engineering Centre, New York, on 19th and 20th September, 1973. RABCEWICZ-COLLOQUY The Austrian Society for Geomechanics is to honour Professor Ladislaus V. Rabcewicz, on the occasion of his 80th birthday, with a meeting in Salzburg Congress Hall on 11th and 12th October, 1973. The themes of the four half-day sessions will be as follows. PYRO MET ALL URG ICAL EVENTS IN 1974 Diisseldorf is to be the venue for the following three events: International Iron and Steel Congress O.F.S. Branch Welkom THE MARCH GENERAL MEETING OF THE BRANCH WAS HELD IN THE ST. HELENA CLUB AT 8.00 P.M. ON TUESDAY, 6TH MARCH, 1973 O.F.S. Branch Welkom MINUTES OF A GENERAL MEETING HELD IN THE ST. HELENA CLUB ON WEDNESDAY, 16TH MAY, 1973, AT 8.00 P.M.

By T. Könighofer

Processing of copper-cobalt orebodies in Africa?s Copper Belt has received much recent attention with various flowsheet options being developed specifically for the refining of cobalt. The upfront leach and copper refining routes are well understood whereas the refining of cobalt is more complex, requiring numerous impurity removal steps to produce high purity metal. This paper describes an investigation into one of the possible processing steps in the refining of cobalt, namely, cobalt solvent extraction. The paper emphasizes the importance of upstream impurity removal to achieve the required cobalt solvent extraction feed composition. 18% (v/v) Cyanex 272 in an aliphatic diluents is used as the organic phase. The pH profiles in the various stages are evaluated in order to obtain a raffinate containing <10mg/l cobalt and with a low magnesium content reporting to the stripping section. The pH profile is also used to minimize the impurity deportment to the cobalt electrolyte. The effect of adding a pre-neutralization stage before feeding the organic phase to the extraction circuit is investigated. Zinc build-up in the stripping stages is also looked at. It is recommended for the purpose of this study that four extraction stages at an O:A ratio of 1 with a pH profile from 4.9 to 5.7 be employed. The pH is controlled with 40g/l NaOH. A pre-neutralization stage is required, where the organic phase is contacted with 10 M NaOH. Two scrubbing stages are recommended at an O:A ratio of 40, using the cobalt electrowinning advance electrolyte as the scrub liquor. Three strip stages are to be employed at an O:A ratio of 0.67.

Jan 1, 2009

By K. Barani, F. Moradpouri, M. Godarzi

A sampling campaign carried out on the lead flotation circuit at Lakan lead-zinc processing plant demonstrated that the Pb recovery was only about 68-69%. Characterization of the Pb flotation tailing showed that 61.4% of the Pb is in the –37 μm size fraction, which is difficult to recover by flotation. Batch flotation experiments were carried out on a plant sample of the lead flotation feed and high-intensity conditioning (HIC) was used to improve flotation recovery. The results showed that increasing the collector conditioning time from 1 to 3 minutes significantly increases the Pb recovery from 42.5% to 57.3%. Further increases in conditioning time to 5 to 7 minutes decreased the Pb recovery. With a collector conditioning time of more than 3 minutes, due to the surface cleaning effect, increasing collector and frother dosage improved the flotation selectivity and recovery, even at higher collector dosages. The Pb recovery increased from 69.1% to 79.8% with increasing impeller speed from 600 to 1250 r/min. HIC increases the flotation kinetics and greatly improves the flotation recovery and concentrate grade.

Apr 2, 2022

COUNCIL The following served on Council during the year under review: Office bearers: Messrs V. C. Robinson (President), Prof D. D. Howat and Dr J. P. Hugo (Vice-Presidents), J. K. E. Douglas (Immediate Past President) and D. G. Maxwell (Honorary Treasurer). Ordinary Members of Council: Dr M. G. Atmore, Dr J. M. Bereza, H. P. Carlisle, W. W. Malan, C. E. Mavrocordatos, Prof R. P. Plewman, Dr R. E. Robinson, Dr M. D. G. Salamon, P. W. J. van Rensburg, L. W. P. van den Bosch, P. A. von Wielligh. Branch Chairmen: J. Meintjes, J. M. Meyer (Acting), J. N. Saunders (Retired). Past Presidents serving on Council: R. J. Adamson, M. Barcza, H. Britten, R. C. J. Goode, P. Lambooy, Prof J. de V. Lambrechts, Dr J. T. Mclntyre, J. F. Reid, H. Simon. Ten Council meetings were held during the year with an average attendance of eighteen and the standing committees held forty-six meetings. FINANCE The annual accounts, which are attached to this report, show an excess of income over expenditure of R5 051 compared with an excess of expenditure over income last year of R4 608. This major reversal of fortunes is due in the first instance, of course, to the increased subscriptions. There were, however, other important contributors, particularly sales of the Proceedings of the Symposium on Open Pit Mining and profits on the operation of symposia and colloquia. It would appear from a study of the accounts that there has been a substantial drop in expenditure on secretarial fees. In actual fact, however, our total expenditure on secretarial fees was higher. A portion of this expenditure was charged against the administration of the Symposium on Open Pit Mining and, in addition, the charge against the Journal accounts for secretarial fees was increased. It will be recalled that in last year&apos;s annual report it was mentioned that subsequent to the new arrangement for publication of the Journal, the expected improvement in the finances of the Journal had been slow in materialising. After a total period of 18 months there was still no sign of improvement and it was accordingly decided to end the arrangement. As a result, the drain on the finances of the Institute was considerably lessened in the second half of the year. During the course of the year Council became concerned about the rapid depletion of our accumulated funds and gave careful and detailed attention to all aspects of the Institute&apos;s financial affairs. Particular attention was given to: 1. The fact that the Institute does not have a solid financial backing and must appeal for funds every time any special event such as a symposium is held. 2. The responsibilities of the Institute to the profession and the community, with particular reference to the desirability of establishing Institute bursaries and participating in other educational activities. 3. The rapidly rising cost of living. 4. The immediate financial position of the Institute. 5. The rapidly increasing cost of publishing the Journal due to the increasing number of papers available. In the meantime the immediate financial position of the Institute has improved but as this is due largely to non-recurring or irregular items of revenue, it should not be given undue weight. After careful consideration it was decided that an appeal should be made to industry for financial assistance, which would be used to cover the cost of symposia and other unusual expenditure and also, if possible, to build up the capital resources of the Institute so that there is a solid foundation for the future. Before appealing to industry, Council wished to be quite certain that there could be no criticism of the Institute for not having done our best in a personal capacity. Furthermore, Council examined many comparative statistics, including those circulated to members, which showed that, while expenditure per member has risen at an average annual rate of 7,5% over the last fifteen years, subscription revenue per member has risen at only 3,4% per annum. It was with this background that your Council decided to raise the subscriptions. Initial approaches have been made to the big mining groups and there has been a very generous response, although the details of how financial assistance will be provided have not yet been worked out. It seems likely that some form of affiliated company membership will be the most suitable method of achieving this. When these details have been fixed, it is the intention to extend the appeal to all corners of the mining industry as well as manufacturing and metallurgical industries. It is believed that these measures will ensure that the finances of the Institute are placed on a firm foundation on which the expanding activities can be planned. The MacArthur Forrest Memorial Fund shows an excess of income over expenditure of R73 and the total fund was, therefore, increased by this amount to R4 411. The balance sheet shows that the market value of quoted shares and debentures increased during the year fron R6 540 to R9 160. The market value is now almost exactly the same as the book value. Accumulated funds now amount to R23 010 compared with R17 959 a year ago.

Excessive dust generation from unpaved mine haul roads is a problem common to most surface mining operations. While optimal road wearing course material selection parameters reduce the inherent dust generation potential, they do not totally eliminate fugitive dust. Many different classes of suppression or palliative treatments are available for mine haul roads and this paper initially ascertains basic selection guidelines, using a set of ideal dust palliative product, application and performance parameters based on mine road-user requirements. An evaluation and modelling methodology for truck generated fugitive dust emissions is developed as a basis for the comparative assessment of dust control strategies. For water-based spraying, a watering model was developed to estimate individual mine road watering frequencies for characteristic site parameter combinations during summer and winter operating conditions, for a required level of control or maximum dust defect. This forms the base-case scenario with which to compare the performance of other types of dust palliatives under the same conditions. Finally, a basic palliative economic evaluation model is introduced with the aim of identifying and costing the establishment, application and maintenance rejuvenation activities associated with the use of chemical palliatives. While palliative cost and performance is generally site specific, it is shown that under certain combinations of conditions, the use of dust palliatives has the potential to deliver cost savings when compared to water-based spraying.

Jan 1, 2007