Search Documents

By R. Xie, J. Liu, Y. Zhu, Y. Li

The surface chemistry features of spodumene and feldspar were investigated by XPS, zeta potential measurements and first principle calculation. The results indicated that the zeta potential of feldspar was more negative than that of spodumene. The most possible active sites on spodumene and feldspar were Al sites and O sites. However, the number, type and activity of these sites were different. The flotation behaviour of five new collectors (cationic collector decyloxy-propyl-amine (DPA), anionic collector α-bromododecanoic acid (α-BDDA), N-Dodecyliminodiacetic acid (DIDA), and mixed collector DPA-BDDA and DPA-DIDA) were investigated through micro flotation experiments and analysed based on the surface chemistry features of spodumene and feldspar. The results revealed that cationic collector DPA processed a high collecting capacity for both minerals. The highest recovery of spodumene and feldspar was 91.60% and 95.30% respectively. The anionic collector α-BDDA and DIDA showed poor flotation behaviour. The recovery of spodumene and feldspar when using α-BDDA as collector was less than 5% and when using DIDA as collector was less than 1%. For the mixed collector DPA-BDDA, the recovery of spodumene and feldspar was 82.27% and 32.61% respectively at pH 4.5. For mixed collector DPA-DIDA, the recovery of spodumene and feldspar was 35.69% and 9.08% respectively at pH 5.8. The results indicated that the cationic collector had high collecting capacity, but low selectivity. The collecting capacity of anionic collector for spodumene and feldspar was poor at the same concentration compared with cationic collectors. Mixed collector DPA-BDDA showed good flotation behaviour and selectivity on spodumene. The ―COO- in mixed collector might improve the selectivity. However, too much ―COO- would increase the electrostatic repulsion, which might cause low selectively and poor recovery. Keywords: Spodumene, feldspar, surface chemistry features, mixed collector, flotation

Jan 1, 2020

By P. R. Jochens

South Africa depends to a considerable measure on the exploitation of mineral reserves and the processing of these minerals. One of the prime requirements for the mining and metallurgical industry to continue in this vital role is access to sufficient energy in a suitable form. Hence, four important questions are discussed: Does South Africa have sufficient energy for the processing of its minerals and metals! Will the cost of energy allow South Africa's minerals and metals to compete on world markets? Can mining and metallurgical processes become more energy-efficiency Can mining and metallurgical processes be adapted to the various forms of energy that may have to be utilized in the future? It is concluded that about 26 per cent of the extractable reserves of coal would be required in the mining and processing of 50 per cent of South Africa's reserves of gold, platinum-group metals, copper, iron, ferrochromium, and ferromanganese. However, the reducing agents required exceed the extractable reserves but not the total estimates of mineable in situ resources of metallurgical coal and anthracitic coal. Even under the severe constraint that coal could become virtually the sole source of energy, only about three-quarters of the extractable reserves of coal would have been consumed by the year 2025. The reasonably assured resources of uranium metal that can be recovered at less than $80 per kilogram are considerable and, at current conversion efficiencies to electricity, are equivalent to one-fifth of the extractable reserves of coal. The rate of exportation of energy in the form of U30. was about five times that of coal in 1978. It is pointed out that the price of energy has a direct effect on the competitiveness of metals, and, although constituting only a small proportion of the selling price of precious metals, it represents a significant proportion of the selling price of copper and metals recovered from oxide ores. The scope for the conservation of energy appears to be greater in the extraction and conversion of primary energy-carriers to electrical energy than in other mining or metallurgical fields. Provided that alternative sources of energy can be converted to electrical energy, they can be applied to the mining and metallurgical industries. The decision as to which type of energy should be used in specific mining and metallurgical situations is complicated, and is likely to be subjected to closer scrutiny than in the past. The hope is expressed that the tentative conclusions reached will give rise to more-quantitative analyses from those qualified to undertake such an exercise. Inevitably, the questions asked at the outset give rise to more questions, and the more interesting ones are posed in the context of each conclusion.

Jan 1, 1980

By J. van der Walt, W. Spiteri

Flyrock remains a significant threat to the health and safety of mine employees and integrity of infrastructure, as well as to the safety of the neighbouring communities and their property. This investigation was motivated by the general lack of fundamental research and mathematically quantifiable data in the literature regarding the relationship between blast design parameters and their impact on flyrock. The focus was to develop a concept that can be used to mathematically quantify the trajectory of flyrock resulting from a blast, which can be used for future research. The ultimate goal for this technique, once it has been fully developed, is to: ➤ Enable mining operations to generate a database with accurate historical flyrock measurements resulting from their blasting operations ➤ Allow research teams to conduct scientific investigations into flyrock and the impact of various blast design parameters ➤ Generate point-cloud data to visualize blasts and flyrock in a virtual reality environment for training and education purposes. This paper summarizes a conceptual technique and preliminary fieldwork that was carried out to determine the technique’s feasibility and motivate further development. The results show conclusively that a modified photogrammetric technique is capable of capturing flyrock data for further processing and analysis. The data acquisition procedure can, at this point, be used to meet the first aim of the project, namely to gather a field database of historical flyrock generation. Further development of the technique is ongoing and it is envisioned that the scientific-based technique will provide a method whereby future flyrock studies will be comparable and that assumptions will be limited.

Apr 5, 2023

By R. Kuyvenhoven, A. Parbhakar-Fox, X. Prieto, J. Quevedo, L. V. Danyushevsky

This paper presents the results of a study focussed on determining the distribution of cobalt in different types of pyrite of the La Estrella IOCG deposit in Chile. In the IOCG mineral deposits, where copper is the main product, the quantification and distribution of cobalt is required to correctly define the technical and economic viability of recovering cobalt as a by-product. In the La Estrella mineral deposit, seven alteration and mineralisation events were recognised through both optical and automated electronic mineralogical analysis. Of these seven events, five different types of pyrites were identified, each with unique characteristics of the pyrite crystals. Through advanced elemental analysis of these five types of pyrites, it was determined that the concentration and distribution of cobalt within the pyrite crystal is dependent on the mineralisation event. The results indicate high cobalt concentrations in the early pyrite mineralisation events, associated with relatively fine pyrite grains, and cobalt generally occurring in a solid form in the pyrite core. The late pyrite mineralisation event exhibits the lowest concentrations of cobalt, with cobalt predominantly present along the outer periphery of the pyrite. These results are relevant from a metallurgical point of view because the preferential location of cobalt within the pyrite crystal will influence the maximum metallurgical recovery of cobalt. For this, a cobaltiferous pyrite concentrate must be formed which, according to the characteristics of pyrite, must be processed with the optimal solubilisation method. The overall objective is to ensure both good cobalt recovery and a high concentration of cobalt in the leach solution resulting from pyrite leaching. Keywords: Cobalt, pyrite, IOCG, copper, metallurgical recovery, solubilisation, Chile

Jan 1, 2020

By Turgay Gurun

"Digital simulation can be used as an analytical tool to optimize the design of crushing plants without need for large-scale experimental programs.General mathematical description of a crushing operation permits the simulation of a crushing plant flowsheet under various operating conditions. The process model encompasses multistage open- and closed-circuit crushing of hard and soft rock. Crushing balances are analyzed in the light of crusher and screen performance and a comparison of different closed-circuit arrangements is made in terms of process and layout criteria.The simulation model allows comparison of process alternatives to be made in terms of equipment selection and capital and operating cost estimation. It thus provides the pertinent practical information to maximize plant efficiency, and to minimize expenditures in such items as equipment, structures, power consumption, and so on."

Jan 1, 2014

By Y. Sagawa

The Hishikari Gold Mine consists of epithermal vein type Au-Ag deposits, each of which has several veins standing almost in parallel each other and inclining 70 to 90 degrees. The veins have 1 to 3m widths and are extracted mainly by drifting and bench stoping with waste rock fill. The Hishikari has tried to optimise the stope dimensions by the Potvin’s Stability Graph Method, which is well known as an easy and effective tool to design appropriate stope dimensions. The method, however, has some limitations of application due to its simplicity so that it has been used only in limited cases. The authors developed a new numerical approach, based on 2D FEM solu-tion for the stability analysis. As a result, it has been possible to solve the Hishikari situation. The authors also introduce the concept of the design approach and compare the results obtained by us-ing the approach with the database of the Stability Graph Method for validation. La mine d’or Hishikari se compose de gisements d'Au-AG avec des types de filons épither-maux dont chacun a plusieurs veines qui sont presque parallèle les unes par rapport aux autres et sont inclinées de 70 à 90 degrés. Les veines ont de 1 à 3 m de largueur et elles sont principalement extraites en creusant et en abattant des bancs de roches encaissantes. Hishikari a essayé d’optimiser les dimensions du chantier d’exploitation avec la méthode de graphique de stabilité de Potvin, bien connue comme un outil facile et efficace pour avoir des dimensions de chantier d’exploitation appropriées. Toutefois, la méthode a certaines limites d’application dues à sa sim-plicité de sorte qu’elle a été utilisée seulement dans des cas limités. Les auteurs ont développé une nouvelle approche numérique, basée sur la solution 2D FEM, pour l’analyse de stabilité. Par conséquent, il a été possible d'expliquer la situation de Hishikari. Les auteurs présentent le concept de l'approche et ils comparent les résultats donnés en l'employant avec la base de données de la méthode de graphique de stabilité pour la validation. Die Hishikari-Goldmine besteht aus Au-Ag-Ablagerungen mit epithermalen Adern, die jeweils mehrere Adern aufweisen, die mit einer Neigung zwischen 70 und 90 Grad nahezu parallel zueinander verlaufen. Die Adern haben eine Breite von 1 bis 3 Metern und werden überwiegend durch Vortrieb von Stollen und Bergversatz abgebaut. Hishikari hat versucht, die Abmessungen des Abbauorts durch das Potvins Stabilitätskurvenverfahren zu optimieren, das als einfaches und effizientes Mittel für die Erzielung angemessener Abmessungen des Abbauorts bekannt ist. Das Verfahren weist jedoch aufgrund seiner Einfachheit einige Anwendungsbeschränkungen auf, so dass es nur in einigen Fällen benutzt worden ist. Vor diesem Hintergrund haben die Autoren einen neuen numerischen Ansatz entwickelt, der hinsichtlich der Stabilitätsanalyse auf der 2D-FEM-Lösung beruht. Dadurch wurde es möglich, das Problem von Hishikari zu lösen. In diesem Dokument stellen die Autoren die Grundlagen des Ansatzes vor und vergleichen die erzielten Resultate durch Benutzung der Datenbank des Stabilitätskurvenverfahrens zur Validierung.

Jan 1, 2003

By H. Ramazi, A. Amini

"This article is devoted to the introduction of a new technique of electrical resistivity data processing called residual resistivity (RR). We define RR as measured resistivity minus background resistivity. To determine the background resistivity, the data acquired from electrical resistivity measurements along a given survey line is evaluated, and then an equation is fitted to the data corresponding to a chosen measurement station as a function of current electrode spacing (or array length). The RR technique was applied to several synthetic models to compare the conventional resistivity inversion of each model with its RR-based inversion. A case study was carried out in a karstic area in Zarrinabad, Lorestan Province, western Iran, to detect the location and geometry of probable cavities by conventional resistivity inversion and RR-based inversion. The results showed that the anomalous zones are better highlighted in the RR-based inversion images in comparison with the conventional inversion images. In some cases, anomalies detected by the RR-based images were hidden in the conventional method. IntroductionThe geoelectrical resistivity method has been widely used since the early 20th century, and plays an important role in several fields such as groundwater and subsurface mineral exploration, geotechnical and environmental investigations, and archeological studies (Bayrak and Senel, 2012; Candansayar and Basokur, 2001; Fehdi et al., 2011; Hee et al., 2010; Osella et al., 2003; Wilkinson et al., 2010). The goal of geoelectrical resistivity surveys is to determine the distribution of subsurface resistivity by measuring the current-potential difference on the ground surface (Aizebeokhai et al., 2010). In the electrical resistivity method, an electrical current is injected into the ground by two electrodes, called current electrodes (AB), and the potential difference is measured between another pair of electrodes, the potential electrodes (MN). Several methods of interpretation are available for application to electrical resistivity data, the simplest being the graphical interpretation of the apparent electrical resistivity pseudo-sections along each survey line. A second method, electrical resistivity inversion, has been developed to create relatively accurate two- and threedimensional computational resistivity models of subsurface sections (Loke and Barker, 1996; Niwas and Mehrotra, 1997; Nordiana et al., 2014; Oldenburg and Li, 1994; Papadopoulos et al., 2009; Yilmaz and Narman, 2014). In the inversion method, models of subsurface objectives are mathematically inverted to reach optimal solutions subject to prescribed objective functions, constrains, and convergence criteria. A common problem when using the electrical resistivity inversion method is that the inversion model of an electrical resistivity profile may be non-unique because different inhomogeneities in the investigation media can result in the same electrical response (Smith and Vozzof, 1984)."

Jan 1, 2016

By T. Bhambhani, J. Jankolovits

Sphalerite flotation using copper sulfate has been performed in the industry for decades and the mechanism of Cu activation is well established. Despite its ubiquity, many practical questions surrounding copper sulfate persist. It is not clear how iron selectivity is achieved in zinc circuits given the propensity of iron sulfides to be activated by copper. Also, the large variation in copper sulfate dosages across different plants and ore types cannot be explained. Lastly, Zn flotation with greatly reduced copper sulfate dosages attracts significant interest and has been demonstrated in certain laboratory settings, but no information is available on why those laboratory solutions have not been adopted in plant practice. Flotation studies are presented that demonstrate that Zn flotation with very low copper sulfate dosages is possible when using certain novel collectors that are not practised in the industry. However, these reagent schemes are impractical because of a heretofore unappreciated and critical role that copper sulfate plays in Fe rejection. With both very low and standard copper sulfate dosages, copper sulfate influences both Zn flotation and Fe rejection. The results highlight the multifaceted role of copper sulfate in zinc flotation and the need to holistically consider complex systems’ behaviour to understand flotation reagent mechanisms and optimise plant performance. Keywords: Sphalerite flotation, metal activation, copper sulfate, iron rejection

Jan 1, 2020

By J. Githiria, C. Musingwini, J. Muriuki

"The maximization of net present value (NPV) is a primary objective in open pit mine planning processes. In an attempt to meet this objective, cut-off grades are considered in all the stages of mining. There are three stages involved in resource extraction, namely mining, processing, and refining/marketing, which are all defined in Lane’s approach. Using Lane’s approach, the economics involved in each stage are identified independently and interact to provide an optimum cut-off grade.A hypothetical block model is used to illustrate how a computer application (Cut-off Grade Optimiser) that was developed in this study is used in the optimization of cut-off grades using Lane’s algorithm. This paper analyses the application of Lane’s approach for a single element in cut-off grade optimization as applied in the calculation of the optimum cut-off grade through a computer-aided application.Although Lane’s approach is not complex it is not widely applied to maximize the NPV of mining operations as the iterative calculations can be lengthy. The computer application developed in this study shows how Lane’s algorithm combined with a linear programming function can optimize cut-off grade with regard to the complex situations faced by mining operations. The application saves users from performing otherwise lengthy, iterative calculations.Background and previous researchAn open pit mining complex constitutes multiple pits, ore processing streams, and metal refining options. An open pit mine produces ore (valuable) and waste material. Ore is transported to an appropriate processing stream for producing concentrate. A refinery processes the concentrate to produce marketable metal product (Lane, 1964, 1988).Cut-off grade optimization is based on Lane’s theory, where a mining system consists of three major stages such as mining, milling, and refining. In this approach the cut-off grade selection is done between six cut-off grades that involve all stages of a mining operation. Selection of the optimum cut-off grade influences the net present value (NPV) by maximizing the net cash flows from the operation."

Jan 1, 2016

By S. W. Jacobsz, Y. Narainsamy

Several high-impact tailings dam failures around the world in recent years have placed a renewed focus on the stability of tailings dams and pointed to potential shortcomings in traditional drained design and safety evaluation procedures. A need to consider undrained shear strength in the design of tailings facilities has become apparent. However, there are specific requirements that need to be met before undrained shearing occurs. In South Africa, the last major failure was likely the Merriespruit disaster in 1994, which leads to the question of whether the conditions required for undrained shearing are readily applicable to South African tailings dams. This paper describes research at the University of Pretoria that has recently commenced to further investigate the conditions required for undrained failure to occur. The research includes laboratory and field testing to replicate these conditions in the laboratory and relate them to those found in an active tailings dam.

Jun 2, 2022

By F. Shi , D. Lay, C. Antonio

High Voltage Pulse (HVP) technology has the potential to transform traditional mineral processing practice in the mining industry. HVP pre-treatment has been shown to enable ore preconcentration, achieve ore pre-weakening and improve mineral liberation. In order to improve the efficiencies of these novel HVP applications, it is essential to understand how HVP operational factors affect ore breakage in HVP pre-treatment. A two-level fractional factorial experiment using two rock samples, a gold-copper ore and a basalt sample, was performed to determine which factors have statistically significant influences on breakage probability, size reduction, and energy efficiency, and which factors have insignificant influences. Operational factors investigated include applied voltage, electrode gap, number of pulse discharges, the number of rocks being processed per batch, and rock size. In total, 1920 batch tests were conducted. For ore breakage characterised in terms of breakage probability and the degree of size reduction during HVP pre-treatment, the dominant factors were identified to be the number of pulse discharges, voltage, and the number of particles present in the processing zone. As all these three factors are related to the specific energy, it is concluded that the specific energy is the most important factor controlling ore breakage in HVP treatment. In terms of the efficiency by which spark energy is transferred from the generator energy, the factors found to have the most dominating influence were the particle size, the number of rock particles present in the processing zone and the voltage. Increasing the values of these factors reduced the loss of HVP energy during the energy transfer process. The factorial experiment using the two ore samples with vastly different mineralisation produced similar results. This proves that the dominant factors affecting HVP breakage are generally applicable to different ores types. Keywords: High voltage pulse, ore breakage, factorial experiment, specific energy

Jan 1, 2020

By T. Szendrei, S. Tose

The generally accepted view in rock blasting is that the sources of energy for the fracture and movement of rock reside in the shock wave and gas action resulting from the explosion, and yet the mechanisms by which these sources interact with the rock have remained unclarified. It has also been noted that up to 50% of the work capacity of an explosive released in a blast cannot be accounted for by field measurements of energy partitioning. In this study, we describe a physical model that details the response of rock to both shock wave and gas action. An analytical model based on momentum conservation is derived to describe the dynamics of shock-driven expansion of the blasthole. Radial expansion of the hole is the key parameter that permits the derivation of the following characteristics of rock response to shock loads: hole expansion time; volume of displaced rock; energy consumed per unit volume; expansion energy efficiency; stress wave pulse length; gas pressure in enlarged hole. Soon after the completion of hole expansion, the shock wave degenerates to an elastic stress wave that runs through the burden. Blasthole expansions of between 50% and 300% of diameter are completed in under 1 ms and, depending on rock properties, consume 32% to 42% of the detonation energy or about 55% of the available mechanical (Gurney) energy. Gas pressure in the enlarged holes in five rock types is between 35 MPa and 650 MPa, and drives the mass movement of burden rock.

Oct 9, 2024

By G. Song, X. Liu

The global coal industry has changed significantly in recent years. In this paper we analyse the coal production and consumption, imports and exports, and coal prices in China and other major coal-producing countries during the past four decades. The analysis shows that global coal production and consumption have declined over the last three years, in striking contrast to the continuous growth for most of the past 35 years. Australia, Indonesia, and Russia have become the world’s major coal providers, while China, India, and the USA, and Germany are the major coal consumers. The world’s, and China‘s, coal industry can be classified into four stages of development: the stable growth phase, stable phase, rapid growth phase, and high-quality phase. Coal prices rose in the world’s four major coal markets in 2016 after four consecutive years of falling prices. The elimination of overcapacity and production-optimizing operations in China could assist in achieving a demand and supply balance.

Aug 8, 2024

By H. Möller, L. Mashigo, C. Gassmann

Wire-arc additive manufacturing (WAAM) is a directed-energy deposition technology that uses arc welding procedures to produce computer-aided designed parts, such as three-dimensional printed metal components. A challenge of additive manufacturing is the anisotropy. Interstitial elements play a significant role in the mechanical properties of Ti6Al4V of different grades. In this research, the mechanical properties of Grade 5 and Grade 23 Ti6Al4V were compared for this application. Samples were extracted from WAAM-produced Ti6Al4V walls in different directions (horizontal and vertical) and at different positions (top and bottom). The samples were subjected to optical microscopy and tensile and hardness tests. Grade 5 Ti6Al4V samples were found to have greater strength, greater hardness, and lower ductility, owing to the higher content of interstitial elements compared with Grade 23. The bottom samples had higher strength than the top samples, which is attributed to thermal cycling during manufacturing, resulting in different microstructures.

Jul 1, 2021

By M. Paricheh, M. Rahmanpour

"The cost efficiency and high reliability of semi-mobile or combined in-pit crushing-conveying (IPCC) and truck systems, compared to conventional truck-shovel systems alone, make them more attractive for use in modern mining operations. Semi-mobile systems, which are the most common systems in open-pit mining, combine the advantages of both systems such that fewer trucks are required, operating costs are lowered, and the operation is environmentally sound. One major aspect of utilizing this system is determining the location of the in-pit crusher and the timing of relocations. Facility location models are rarely used in the mining sector, but these models may be used for solving the in-pit crusher location problem. To this end, the main parameters affecting the IPCC location in open pit mines are reviewed and examples given of how they are applied to a dynamic location-relocation problem. Subsequently, the model is implemented for Sungun copper mine in Iran and the number and the exact time of relocations of the IPCC units determined. IntroductionNowadays, compared to the last century, metal prices are more volatile, average and cut-off grades have decreased, and stripping ratios increased. From a mining engineering point of view, many ore deposits with simple access and low capital and operating costs have been exhausted. The remaining deposits are located at depth, with no easy access, which requires high initial capital costs (Osanloo, 2012). Mining at great depths and high tonnages is possible only through open pit mining. Today, more than 80% of open pit mines in the world use a shovel-truck system for loading-hauling operations (Osanloo, 2010).With increasing depth, haulage distances increase and the number of loads per truck decreases. As a result, fuel, tyre, and depreciation costs per ton increase. Owing to these factors, open pit mining at great depth (300 to 1000 m) using shovel-truck systems faces some technical and economic problems. In-pit crushing-conveying (IPCC) systems have been known in the mining industry for many decades. The idea was introduced in 1956 in Germany. Today, the cost efficiency and high reliability of IPCC make it more appealing than conventional shovel-truck operation, especially in longer life projects with lengthy transportation distances and high production rates (Koehler, 2003). Since 1956, different aspects of this system have been reviewed by many researchers. Barua and Lanergan (1985) developed a computer program that compares the tonnage aspects of various conveyor layouts. They believed that to maximize the economic benefit of lower haulage costs associated with in-pit conveying, one must first minimize the cost of the flatter slope, which is expressed in terms of additional stripping or tied-up ore. Dos Santos and Stanisic (1987) evaluated the design of a high-angle conveyor at the Majdanpek copper mine. Then, Sturgul (1987) applied GPSS (general purpose simulation system) to find the best location of an in-pit crusher."

Jan 1, 2017

By Y. Belloa, C. Dorfling

The presence of impurities such as Se and Te in copper sulfate leach solutions can have a detrimental effect on electrowinning efficiency. These elements can be removed from the solution by precipitation; sulfurous acid is commonly used as a precipitation reagent, while studies have also reported improved precipitation with the addition of metallic copper. This paper aimed to determine the effect of conditions used during the solution purification step on the characteristics of the precipitates that formed. Precipitation tests were performed in a batch reactor with copper sulfate leach solutions obtained from the base metal refinery of a platinum group metal producer. The effects of agitation rate (250 and 500 rpm), SO2 flow rate (4.4 and 5.8 mL/min.L), temperature (65 and 95°C) and metallic copper powder addition (0, 1 and 2 g/L) on the characteristics of the precipitates formed during the tests were determined using scanning electron microscopy. The major phases detected in the precipitates formed when using SO2 as the only precipitation reagent were elemental Se and Cu2Se. The introduction of copper powder led to the production of different sulfide phases for the experiments conducted at 65°C irrespective of the values of the other reaction parameters. At 95°C, Cu crystals, Cu2O and tiny inclusions of Cu2(Se,Te) were the prominent phases noticed in the precipitates produced from all the tests conducted with copper powder as precipitation enhancing reagent. Keywords: copper, precipitation, selenium, tellurium

Jan 1, 2020

By E. D. Musin, S. S. Gudkov, A. V. Epiforov, S. V. Balikov

The standard technology for processing of gold-bearing sulfide raw material has many problems associated with the use of cyanide as a gold lixiviant. Therefore, many tests to find alternative gold recovery methods are being undertaken. This paper describes some technological solutions, which can become alternatives to cyanide technology in the future. Pressure oxidation (POX) of refractory gold-bearing sulfide concentrates from five different Russian gold deposits were investigated. Concentrate 1 was gold-copper concentrate. Concentrate 2 was gold-pyrite concentrate. Concentrates 3-5 were pyrite-arsenopyrite double refractory concentrates. The POX tests were at temperatures of 110, 200 and 220 °C and oxygen pressures of 1.5, 2.4 and 3.0 MPa were carried out. Gold lixiviants, such as chloride, thiosulfate, sulfite and thiocyanate were tested. The recovery of gold from sulfide gold-bearing concentrates by non-cyanide methods was 97- 99%, and from double refractory concentrates, 86-93%. The tested reagents are less toxic than cyanide, and their use will reduce of the cost of gold production. These methods make it possible to recover gold in acidic media, and eliminate the washing operation and POX slurry neutralisation. In addition, precious metals recovery from POX cakes using lead reduction smelting was investigated. It was shown that the “POX-pyrometallurgical” technology for double refractory concentrates processing could be used with recoveries of gold and silver of 97 and 96%, respectively. Keywords: Recovery of gold, refractory sulfide gold-bearing concentrates, double refractory concentrates, pressure oxidation, non-cyanide lixiviants of gold, chloride autoclave leaching, thiosulfate leaching, thiocyanate leaching, sulfite leaching, reduction smelting, POX-pyrometallurgical technology

Jan 1, 2020

By S. R. Grobler, S. Bilessuris, M. E. Greenway

Ensuring that all the head ropes on a multi-rope friction winder share the load equally has been a design and maintenance issue since they were first developed. Accurate machining of the rope grooves is necessary to meet this objective. Early analysis of the change of rope loads for ropes in grooves that are mismatched in depth treated the grooves as rigid. Groove depth tolerances deduced from this analysis are stringent and difficult to achieve in practice. Test work indicated that the inherent flexibility of groove lining materials alleviates the load-sharing problem. However, no analysis of rope load changes due to mismatched flexible grooves has been published. In this paper we develop new equations for the rope load variation for flexible grooves. By allowing flexibility to reduce to zero, the corresponding rigid rope groove equations are obtained. New criteria for tolerable groove depth variations are developed from this analysis, which depend on the flexibility of the groove lining material.

Sep 1, 2021

By S. Swanepoel, A. V. Cherkaev, Q. G. Reynolds, M. Erwee

Ferrochrome (FeCr) is a vital ingredient in stainless steel production and is commonly produced by smelting chromite ores in submerged arc furnaces. Silicon (Si) is a componrnt of the FeCr alloy from the smelting process. Being both a contaminant and an indicator of the state of the process, its content needs to be kept within a narrow range. The complex chemistry of the smelting process and interactions between various factors make Si prediction by fundamental models infeasible. A data-driven approach offers an alternative by formulating the model based on historical data. This paper presents a systematic development of a data-driven model for predicting Si content. The model includes dimensionality reduction, regularized linear regression, and a boosting method to reduce the variability of the linear model residuals. It shows a good performance on testing data (R2 = 0.63). The most significant predictors, as determined by linear model analysis and permutation testing, are previous Si content, carbon and titanium in the alloy, calcium oxide in the slag, resistance between electrodes, and electrode slips. Further analysis using thermodynamic data and models, links these predictors to electrode control and slag chemistry. This analysis lays the foundation for implementing Si content control on a ferrochrome smelter.

Mar 14, 2024

By A. F. Silva, J. M. G. Sotomayor, V. F. N. Torres

Geotechnical monitoring plays an important role in the detection of operational safety issues in the slopes of open pits. Currently, monitoring companies offer several solutions involving robust technologies that boast highly reliable data and the ability to control risky conditions. The monitoring data must be processed and analysed so as to allow the results to be used for several purposes, thereby providing information that can be used to manage operational actions and optimize mining plans or engineering projects. In this work we analysed monitoring data (pore pressure and displacement) and its correlation with the tension and displacement of the mass of an established failure slope calculated using the finite element method. To optimize the back-analysis, a Python language routine was developed using input data (point coordinates, parameter matrix, and critical section) to use software with the rock mass parameters (cohesion, friction angle, Young’s modulus, and Poisson’s ratio). For the back-analysis, the Mohr-Coulomb criterion was applied with the shear strength reduction technique to obtain the strength reduction factor. The results were consistent with both the measured displacements and the maximum deformation contours, revealing the possible failure mechanism, allowing the strength parameters to be calibrated according to the slope failure conditions, and providing information about the contribution of each variable (parameter) to the slope failure in the study area.

Oct 1, 2021