Search Documents

This report summarizes the results of the Narragansett Win Projec't's activities during the U.S. Bureau of Mines (BOM) Phase 1, which was transitional from and which followed the National Science Foundation (NSF) Phase which initiated the investigation of New England's potential roil resource. The 960 sq. mile basin is structural and topographic lowland containing 12,000 to 20,000 ft. of terrigenous clastic sediments of late Pennsylvanian age, and which rests on an upper Precambrian and Cambrian basement. The Rhode Island Formation, which is the coal-bearing unit, comprising the bulk of the Pennsylvanian rocks consists, in order of decreasing abundance, of sandstone, conglomerate, silts tone, shale, and coal. In the NSF Phase, 24 drill-holes yielded 17,900 ft, of core; in the BOM Phase I study, 4 drillholes yielded 2,100 ft. of core. Anthracite and semi-anthracite was encountered in beds Up to 30 ft. thick in widely spaced parts of the Basin. The coal, typically very low in sulfur, and a high ash anthracite, won mined in substantial volumes from 1808 to 1959 from shaft and open lit in Portsmouth and Cranston, R.I., and in lesser volumes in Mansfield, Mass. Currently coal is now being mined in Plainville, Mass. as a fuel in the manufacturing of light-weight aggregate from the same quarry that serves as the source of the rock being processed. The structurally complex Narragansett Basin is now known to have a greater extent than earlier since recent drilling by others (Chapter 2) has confirmed our interpretation that the Basin extended offshore south A Boston. The, Basin also extends into Rhode Island Sound to the south. The geological structure is more complex in the southern part of the Basin than in the northern part. Three episodes of folding have been documented on Aquidneck Island and four episodes of faulting have been demonstrated for the Basin as a whole. Relatively less well exposed rock in the northern part of the Basin, increases the difficulty of recognizing and correlating structural episodes in the northern part of the Basin. The Basin his hewn subdivided into six structural domains which appear to have distinctive structural, metamorphic, paleontological and sedimentological differences that mw assist in isolating important events in the evolution of the Basin and its component parts. The tentative structural model recently developed in POP Phase I has important implications for exploration and mining. In the first and second folding stages the coal is mobilized and thickened in the crests and troughs of folds whose axes are horizontal to subhorizontal. While conventional coal exploration and mining methods are not applicable, great thickening in the crests and troughs of large scale structures, which can he defined by geology, geophysics and drilling, may provide compensating advantages. Bedrock over most of the Basin is 0-50 ft., but thicknesses of glacial deposits up to 150 ft. are present locally. Pro-Pleistocene topographic trends are controlled by structure and rock hardness; Pleistocene deposits aligned to the S. F. are superimposed on earlier trends. The southern part of the Basin is mainly dominated by high grade Barrovian metamorphism and plutonism of Permian age, related to the Alleghanian Orogeny. About 300 sq. miles of the 960 sq. mile Basin has been affected. The remaining 660 sq. miles, in the chlorite and subchlorite zones of metamorphism are compatible with the presence of high quality anthracite and semi-anthracite. Illite crystallinity studies begun in the NSF Phase, have been carried out in the BOM Phase l with important results. About ME of the northern Basin is now known to be in the diagenetic (unmetamorphosed) or subchlorite zone and the remainder in the chlorite zone of metamorphism. Mite studies, probably best recording temperature effects, show a generally progressive increase from the NW corner of the Basin near Plainville, Mass. toward the south and southeast. Reflectivity and coal petrography studies, probably best recording pressure and effects related to shearing, indicate a generally opposite pattern. Thus these methods provide powerful tools for the ultimate solution of problems important to coal exploration for coals of higher combustible volatile content and exploitation of these. Due to the complex nature of the coal, chemical data may not he easily used to determine rank. The coals have been tectonically deformed and mineralized. This deformation plus thermal metamorphism have altered the coals, in some cases by producing natural coke. Brecciated coal is often coated with a secondary depositional carbon. The coals' hydroscopic nature and high ash contents are due to the deformed nature of the coal and the presence of this secondary carbon. The stratigraphy and sedimentology of the coal-bearing Rhode Island Formation is similar to described alluvial fan deposits. The non-geological studies al-low three conclusions to be made: 1. A substantial number of areas have been identified in the Narragansett Basin in which mining could be carried out without undue difficulty from a land use point of view. 2. Substantially more than two hundred instances of past or current- mining activities have been identified in the Basin. Many of those are in areas defined as geologically interesting, and may be advantageous From the point of view of future exploration. 3. The map synthesis technique developed for this contract is successful and may easily be adapted to future exploration in its current form and also in its expandable form dealing with unit measurements of one-tenth mile. We recommend that BOM Phase 2 exploration should accomplish the intent of the Congressional language in House Report No. 95-1251, to continue a substantial drilling and geophysics program: "The Committee expects the Bureau to continue studies involved in ascertaining the extent and quality of low sulfur coal reserves in the Narragansett Basin in New England including necessary drilling and geophysical studies. The knowledge of the extent of such deposits is of great importance to this 'energy pour' area".

Jan 1, 1979

By G. D. Andria

Contract J0275007 was to consist of a thorough two-phase statistical analysis of respirable coal mine dust data from USBM Contracts H0232061, H0232060, H0230029, H0230031, H0210050, and H0242013. Consequently, BCR cataloged and assembled relevant data items from these contracts and formulated procedures suitable for the evaluation. The selected procedure was a Multilinear Regression Analysis which related dust concentrations measured in the mine to other mine parameters. Under the first phase, a thorough analysis of the date from USBM Contract No. H0230029 was completed. Primary results from this analysis are as follows: (1) The five variables that significantly affect dust concentrations in the return behind the brattice are the spray system utilized; the distance from the face to the return brattice; the return airflow; the production rate; and the water consumption rate, in that order. These five variables describe about 85 percent of the total variation in the return dust concentration. (2) Results at the miner and jack-setter locations were somewhat less conclusive due to the fact that only 17 percent of the variation in dust at the miner could be resolved and only 48 percent of the variation at the jack-setter location could be explained. The decision of the sponsor was that these initial results revealed as much information as could be expected; thus, per instructions from the USBM, the second phase (analysis of the other five contracts) was abandoned.

Jan 1, 1978

Reports by researchers in government, industry, and universities of the United States are given for various projects on basic coal research concerning, the metamorphism, physical and chemical properties, and reactions of coal, and how many of these studies can lead to better utilization of coal.

Jan 1, 1968

By K. J. Liles

The Bureau of Mines conducted laboratory semicontinuous and continuous heavy liquid tests to determine the feasibility of producing commercial-grade products from the high-clay sylvinite ores of the Permian Basin in New Mexico. Continuous test operations demonstrated that concentrates containing 59.9 percent K2O and recoveries of over 75 percent of the contained potash can be obtained. The organic heavy liquid was effectively recovered by vaporization, condensation, and absorption methods. Less than 5 parts per million of heavy liquid vapors were released to the atmosphere. This loss represents only 0.02 pound of heavy liquid per ton of ore treated.

Jan 1, 1973

By Rupert O. Yantz

This report, authorized under contract Number H0111403 Amendment Number One, entitled, "Exploration of Illumination Concepts for Underground Coal Mines", contains the results of an investigation of methods, procedures, and technology for providing working place lighting in underground coal mines and construction of a prototype, man portable, mine illumination system and a prototype, machine mounted, mine illumination system for use in high and low coal entries of underground coal mines.

Jan 1, 1972

By Mark S. Stagg

Blast-induced ground vibrations from surface coal mine, quarry, and construction blasting were measured and analyzed for frequency content and duration characteristics. Eighteen commercially available ground vibration measurement systems were evaluated in the field and laboratory for linearity, accuracy, and crosstalk. Buried, surface, and sandbagged transducer placement methods were compared, along with peak and vector-sum measurements. The recommended minimum frequency ranges for ground vibration instrumentation are 2 to 150 Hz for coal mine and quarry blasting, and 5 to 200 Hz for construction and excavation blasting. When higher or lower frequency vibrations are possible, as in construction blasting or for a quarry shot close to a residence, care should be taken to insure proper choices of instrumentation and vibration criteria. Several instruments operating in these ranges are available, and all but one of the seismographs tested fell within ±3-dB accuracy limits (+41 pct, -29 pct). Waveform recordings of all three ground vibration components are recommended as the peak amplitude and frequency may vary among the three. Peak or vector-sum readings are adequate if only amplitude levels are desired. The soil density matched box should be anchored or buried, particularly for high-frequency, high-amplitude construction blasting.

Jan 1, 1980

By J. Sottile, J. L. Kohler

Component failures in the electrical control circuits of mining machines account for a large percentage of the total downtime of the machine. Once a failure has occurred it is always a tedious and usually a time-consuming task to locate the failed component. Moreover, the pressure to quickly locate the cause of a delay can lead to compromises in safety. Thus an onboard diagnostic system, essential for an automated machine, would be a very useful addition to existing machines. This report details U.S. Bureau of Mines development of a generic procedure for synthesizing diagnostic systems for electrical-control-circuit failures in mining machinery. A continuous mining machine is used as the testbed to illustrate the application of the developed methodology. Substantive differences among mining machine control circuits made it impossible to achieve a generic diagnostic system, but a generic approach for the synthesis of the diagnostic system was possible. As the research progressed, it became apparent that an algorithmic approach was better than an expert- system-based implementation. A prototype system was constructed and used to evaluate the diagnostic system. Prototype implementation issues are also examined.

Jan 1, 1993

By Cliff McCartney, Michael A. Trevits

The National Institute for Occupational Safety and Health (NIOSH) is conducting a program of research to evaluate and improve remote mine seal construction technology for mine fire control and suppression. The main focus of this work is to develop reliable technology that will remotely seal a mine opening from floor-to-roof and rib-to-rib. NIOSH, in partnership with Strata Mine Services Inc.1, is evaluating the capability of a two-component phenolic foam-based product, called Rocsil®1, that is intended for cavity filling, air and gas sealing, and consolidation of highly fractured strata. Rocsil® can be rapidly applied, has a quick cure time, a high expansion rate, good compressive resistance and excellent anti-static properties. When the resin and catalyst are mixed, an immediate foaming reaction occurs followed by rapid expansion up to 30 times the original volume. By virtue of its fire-resistance properties, Rocsil® foam has application for sealing underground mine areas undergoing heating from spontaneous combustion and it could be useful for remote mine seal construction to aid in mine fire control and suppression. This paper presents an overview of remote mine sealing technology, introduces the use of Rocsil® foam for remote mine seal installations, offers a case study of the use of this rigid foam material to remotely construct a temporary in-mine seal and discusses technology improvements. Disclaimer: The findings and conclusions in this report are those of the authors and do not necessarily represent the views of NIOSH.

By N. E. Hanna

The current list of permissible explosives includes 124 different brands. Fifteen of these are gelatinous, and the rest are the more commonly used granular ammonium nitrate type. Their rates of detonation range from 1,300 to 5,600 meters per second, and the weights of 1-1/4 x 8-inch cartridges range from 86 to 244 grams. The list of permissible blasting devices includes 1 Cobra, 2 Hydrox, and 9 Cardox models. All of these devices are based on discharge of high-pressure gas from a pressurized shell in a shothole. INTRODUCTION To be approved for use in underground coal mines in the United States, explosives and blasting devices must pass certain schedule tests prescribed by the Bureau of Mines. The explosives listed here were tested under Schedule 1-G,3 which has since been replaced by Schedule 1-H;4 the blasting devices were tested under Schedule 26A.5

Jan 1, 1962

The Federal Coal Mine Health and Safety Act of 1969 limits to 2 milligrams per cubic meter (for dust containing a maximum of 5% quartz) the average respirable dust concentration to which individual miners may be exposed. Section 205 of the Act directs that an appropriate exposure formula for dusts with quartz content in excess of 5% be established. This formula, entered in F. R. Document 70-12351 filed September 16, 1970, is 10 milligrams per cubic meter divided by % quartz. Thus, the total respirable dust exposure permitted limits the quartz to a maximum of 100 micrograms. For example, if % quartz is 5%, 10 mg/5 = 2 milligrams, and (.05) (2 mg) = 100 micrograms. Similarly, if % quartz is 10%, 10/10 = 1, and (.10) (1 mg) = 100 micrograms, etc. If the % quartz is less than 5%, the 2 mg/M3 limit prevails.

Jan 1, 1974

By J. R. Cobble

The Federal Bureau of Mines conducted static tests at 2,500° F on 39 refractory compositions, and dynamic tests at [2,825°35° F] on 31 commercial refractory brick specimens to determine their resistance to corrosion and erosion by a slag similar in composition to that used in producing insulating mineral wool. The static tests showed fireclay, low-alumina compositions (<70 percent A1203), zircon, zirconia, SiC, and clay-bonded graphite refractories to be unsuitable. Dynamic test results indicated that magnesia and chromia compositions were superior to high-alumina compositions (=70 percent A1203) as a furnace lining for melting mineral wool. Data from these tests indicated that magnesia and chromia compositions with low RO/R203 mole ratios were more resis tant to attack by mineral wool slags than ones with high RO/R203 mole ratios.

Jan 1, 1975

By R. W. Barnes

This circular presents results of a survey conducted by the Bureau of Mines to ascertain the extent to which dust-control practices are employed in the coal-mining industry. This survey was initiated because of increasing realization of the possible harmful effects of the inhalation of dust upon the health of coal-mine workers and the advent, during recent years, of new types of mining machinery and new mining methods that may have a direct effect upon the extent of exposure to airborne dust experienced by persons mining coal. Anthracite Mines The survey covered 169 anthracite mines that were operating from November 1, 1953, to July 1, 1954. It showed that large mines employing more than 100 men were doing most to control dust produced during mining.

Jan 1, 1956

By Frank G. Horino

This report presents a method of utilizing the Coulomb strength criteria for estimating the strength and stability of pillars and pit slopes containing planes of weakness. It is assumed that the Coulomb theory, as a special case of the Mohr envelope, is a satisfactory first approximation of failure in uniaxial compression or triaxial loading with low lateral loads. Accepting this assumption for brittle materials, an expression for the strength decrease of rock pillars containing a plane of weakness or fracture at any angle of orientation is derived. As few as six samples (three solid cores and three fractured cores at a failure-oriented angle) are required for testing uniaxially and triaxially to statistically determine the coefficients of friction and the shear strengths of both the solid rock and the fracture plane and the range of failure angles of the fracture plane. Interpretation of the data shows that the mean normal stress and maximum shear stress technique of analyzing the data is superior for solid core and that shear and normal stress values using angles of failure should be used for fractured specimens with failure-oriented angles. Plots of either the strength or strength ratios against fracture angles obtained from oriented drill core samples give a useful first approximation of strength decrease due to fracture. Using the same test conditions for both fractured and unfractured material increases the validity of the tests.

Jan 1, 1970

By W. F. Watts

This report describes the Mine Inspection Data Analysis System (MIDAS) developed by the Bureau of Mines to analyze the records of industrial hygiene samples collected by the Mine Safety and Health Administration (MSHA) in metal and nonmetal mines. MIDAS is the first system capable of sorting, editing, analyzing, and reporting these data. It is also the first system designed to be used by a number of Government agencies. At present the system contains 225,000 personal and area samples for 61 contaminants in 45 industries. The records date from 1974 to early 1980, and MSHA plans to provide yearly updates to the system. This report presents preliminary analyses of dust exposures and discusses the potential uses and limitations of these data. Analysis of the dust data for 1978 and 1979 showed that bagging had the highest percentage of dust overexposure. Morn than 40 pct of the 1,536 respirable quartz dust, total nuisance dust, and total silica dust samples exceeded the MSHA exposure limit. Other dusty occupations are ranked according to their percentage of overexposure.

Jan 1, 1981

By Mark P. Zaitsoff

The project involved design, construction, and testing of hydraulic models of culverts, decant and open channel spillways which are typical drainage structures used for protecting mine waste embankments. MSHA (The Mine Safety and Health Administration, U. S. Department of Labor) made a motion picture of the tests. Tests results and products in the forms of graphs, tables and films, demonstrate the principles and factors which govern the function and performance of the three types of drainage structures.

Jan 1, 1981

By David Oyler, Craig Compton

The The National Institute for Occupational Safety and Health (NIOSH) Pittsburgh Research Laboratory (PRL) is continuing to investigate the behavior of fully grouted roof bolts in the weak roof rock of the Safety Research Coal Mine (SRCM). This paper describes the results of three studies: • A series of 24 pull tests of bolts installed fully grouted and overcored to leave 12 inches of grouted bolt. The tests compared the pull-out performance of offset-head roof bolts with that of standard 5/8-inch bolts; • A second series of 24 tests that compared the pull-out loads obtained by bolts installed with 1 ft of resin (a Short Encapsulation Pull Test or SEPT) to that of fully grouted bolts overcored to leave only 12 inches of grouted bolt, and; • An investigation into the pressures generated during the installation of fully grouted resin bolts. All of the bolts installed and pulled were overcored and removed from the roof after the pull tests to allow inspection of the resin. The first study found that there was no significant difference in pullout load between the offset-head bolts and the standard bolts. The second study, comparing the SEPT bolts and the partially-overcored fully grouted bolts, indicated that SEPT can significantly underestimate bolt anchorage grip factor, suggesting that the SEPT is a conservative measure of actual bolt performance. Significant loss of resin to cracks in the roof was observed in the bolts overcored in the SRCM. The third study explored one possible explanation for the resin loss, high pressures generated during bolt installation. These tests employed bolts installed in strain gauged steel tubes. The results confirmed that significant pressures (greater than 4,000 psi) can be generated during bolt installation. The results of the pressure tests, combined with the observations of resin loss in bolts installed in the SRCM, suggest that under some circumstances resin loss and under-encapsulation could take place and lead to degraded bolt performance. Glove fingering was observed in all recovered bolts to various degrees. The limited comparative data suggested that the effect of glove fingering ranged from slight to moderate. Complete mixing of the resin was observed on all of the 40 bolts recovered (28 fully grouted and 12 SEPT). Australian and U.S. resins were compared and the Australian resins were observed to have much smaller catalyst compartment areas and lower resin viscosities. These differences are suggested as potential explanations for occasional resin mixing problems noted in Australian resin bolt installations.

By Peter J. Clarke

The Soviet-controlled Government in Afghanistan continued to emphasize development of the country&apos;s mineral resources, primarily to supply raw materials and fuel to industrial areas in the Soviet Central Asian republics. In addition to expanding production of natural gas for export to the U.S.S.R., a $600 million2 Soviet-Afghan cooperation project, 1 of 167 such projects established since 1981, was devoted to exploiting the Ainak copper deposit, south of Kabul in Logar Province. Also being developed was the large Hajigak iron ore deposit in the Hindu Kush Mountains, 100 kilometers northwest of Kabul. In addition to these minerals, Afghanistan already produced small quantities of barite, cement, coal, gypsum, salt, and possibly some lapis lazuli. Afghanistan was the world&apos;s leading producer of lapis lazuli, a semiprecious gem stone, prior to the Soviet invasion in 1978, but production, although no longer reported, has probably been significantly reduced. It was also reported that Soviet mining engineers and technicians have commenced producing uranium from Lashkangah in the mountainous Khawaja Rawash area near Kabul.3 The Government was also considering mining chromite from Herserak and Mohammed Agha Kulanger, near the border with Pakistan.4 Afghanistan&apos;s overall economy remained stagnant in 1983, a result of continuing armed resistance to the Soviet-installed government. The gross domestic product (GDP) was estimated at about $2.8 billion, only marginally higher than the 1982 level. The value of exports was estimated at $720 million, up less than 2% over that of 1982, while imports rose approximately 8% over the same period. Natural gas was by far the leading export, earning about $295 million, up 4% over that of 1982. Approximately 90% of Afghanistan&apos;s natural gas production was exported to the U.S.S.R. Gas exports were used to pay the country&apos;s debt to the U.S.S.R., and also to pay for its supplies of petroleum products and other goods, which were imported almost exclusively from the Soviet Union. Some of Afghanistan&apos;s petroleum products were supplied by the U.S.S.R. as grants in aid, as Afghanistan did not have any domestic petroleum refining capacity.

Jan 1, 1985

By J. R. Thoenen

This circular is part 6 of the third paper (entitled "Excavation") of a series summarizing the technical problems involved in the production and preparation of sand and gravel. Part 1 discussed the use of power shovels, draglines, and excavator cranes; part 2, power scrapers, slackline cableway excavators, and hydraulic monitors; part 3, hydraulic, clamshall, ladder, and diaper dredges; part 4, haulage equipment, particularly industrial cars with locomotive or hoist as the motive power; part 5, conveyor belt, motor truck, pump and pipe line, towboat and barges, and aerial-trams haulage. This circular discusses the application of these various types of equipment to the different types of sand and gravel deposits and contains a reference bibliography. It completes the discussion of excavating problems.

Jan 1, 1936

By Thomas J. Peters

In 1984, at the request of the Bureau of Land Management, the Bureau of Mines studied 7,000 acres of the 9,240-acre Little Blitzen Gorge Wilderness Study Area in Harney County, OR, to evaluate its mineral resources. The study area is dominated by a 1,500-ft-deep canyon that was carved by Pleistocene glaciers in gently westward-dipping homoclinal flows of Miocene Steens Basalt. The Bureau reviewed pertinent literature and county mining records During the field investigations, 18 rock samples were collected from basalt dikes, breccia, fractured or porphyritic flows, and 20 alluvial samples from gravel accumulations. Mercury anomalies from sampling by the Oregon Department of Geology and Mineral Industries could not be verified. The mercury might have originated -From the Pike Creek Formation, a known mercury-producing unit that may extend into the study area beneath the Steens Basalt. Any epithermal deposit at depth would be expensive to explore and develop.

Jan 1, 1986

By Robert L. Lappi

Eight interburden handling concepts are developed for multiple seam area mine stripping operations in central and western United States. They are based on data gathered and analyzed during field surveys, literature reviews and visits to state requlatory agencies in five states. It is concluded that improvement of reclamation practices through selective interburden handling techniques is possible at lower operating costs than currently incurred. Specific multiple seam mining systems are discussed in this report.

Jan 1, 1980