Search Documents

Reduce dust at the auger mine face by modifying airflow patterns, around the minim machine. Approach Limited clearance between an auger miner and the mine root restricts airflow across the face and causes dust rollback. Directional sprays arc used to direct air across the face, thereby reducing dust rollback and increasing dust dilution (fig. 1). Laboratory and underground studies were used to test and optimize effectiveness of the directional sprays. Results of Laboratory Study Laboratory experiments were conducted in a simulated auger gallery equipped with a full-scale mock auger miner and bridge conveyor. A dual curtain configuration was used to direct the, ventilation, which averaged 2,700 cfm throughout the experiment. Testing variables included spray location, pressure, spacing, orientation, and number. Figure 2 shows the optimized directional spray system, also called the auger clearer spray system. The system consists of three sprays mounted alone the intake side of the miner. Sprays arc spaced 16 to 24 inches apart, and angled 30° toward the return side of the miner. The 24-inch spacing moved about 7% more air across the face than the 16-inch spacing; however, it resulted in some additional misting on the return side of the miner. A 30° orientation was more effective than a 60° orientation for moving air across the face and minimizing misting on the return side of the miner. Flat fan sprays arc used because their spray paths arc not obstructed by the top of the miner and mine roof, A 50° fan angle is used to minimize misting on the intake side of the miner.

Jan 1, 1989

By T. Bajpayee, L. Prosser, A. Iannacchione, G. Esterhuizen

Reducing the number of roof fall injuries is a goal of the NIOSH mine safety research program. Central to this effort is the development of assessment techniques to help identify the nature of the risks associated with working under potentially hazardous roof conditions. This paper discusses a method to determine the roof fall risk using a qualitative risk-analysis technique. The ability to determine roof fall risk has been a long-standing goal of safety professionals and could provide the kind of information needed by on-site personnel responsible for worker safety to mitigate roof fall injuries.

Rapidly identify unstable mine waste embankments and similar dam structures. Approach Aerial photography, geotechnical instrumentation, and telephone or satellite data transmission are used to supplement walk-around inspect ions. How It Works Embankment stability and other indicators of structural integrity are evaluated using aerial photography, and on-site unattended instruments and data transmitting systems. Evidence of external movement and water seepage is obtained from aerial photography and photogrammetric evaluation techniques. Surface points marked by stake- mounted targets are monitored photographically at time intervals of several weeks or months. Photographic measurements of x, y, and z coordinates of these points are obtained from flying a series of photo-runs over the dam.

Jan 1, 1979

Improve the safety and reduce the cost of longwall entry support. Approach Replace the conventional wood cribbing with stronger, non-rotting and lower cost cribbing made of steel-fiber-reinforced (SFR) concrete. How It Works Conventional concrete can suddenly fail under excessive compression loads, but adding steel fibers to the concrete, before it is mixed with water, changes the failure mode to a gradual and controlled failure characteristic similar to wood. A system for making SFR concrete crib blocks was designed and developed (or use in constructing walls and cribs to support coal mine roofs. The SFR concrete cribbing is stronger and stiffer than wood, and avoids wood's disadvantages of: flammability, deterioration under chemical or bacteriological attack, methane generation, and relatively high cost. Use of SFR concrete also allows freer movement of miners, equipment, and ventilation air, because much less volume of SFR concrete is required than wood for a given amount of support, and because the roof-to-floor closure is greatly reduced by the stiffer supports.

Jan 1, 1981

By Richard L. Unger

Equipment is the primary cause of injury in 11% of all mining accidents and a secondary cause in another 10%. Purchasers should select new equipment carefully to ensure that the machine incorporates good ergonomic design criteria that maximize the safety of their mine workers. One potential problem area is the workstation-the control center of the machine. Safety problems often occur when the workstation provides insufficient clearance or visibility to the operator or has controls that are difficult to reach. This is especially true for underground mines, where confined space is an issue. In reclined or stooped postures, operators will have less strength and agility and often experience reduced visibility. We have conducted and published much research in Human Factors design of mining machine workstations. This information is currently being compiled into a series of Human Factors design recommendation reports. The reposts dl cover many topics, including workstation layout, control design, seating, and visibility. Each topic has a list of basic or first principles of design. Understanding these principles is the key to designing or purchasing a workstation that is both safe and efficient. Following is a sampling of these main topics and first principles.

Aug 1, 1996

By H. W. Lang

The Bureau of Mines conducted an investigation to observe the effect of cetane improvers upon nitrogen oxides concentration in diesel exhaust gas. Amyl nitrite and amyl nitrate were used as additives to the fuel used in a four-cycle, single cylinder type test engine. It was concluded that nitrogen oxide concentrations were not enhanced at fuel-air ratios above 0.03 pound of fuel per pound of air.

Jan 1, 1969

Identity the difficulties of establishing vegetation on mining-related wastes resulting from adverse chemical, physical, and biological properties; describe the ecological and soil factors affecting the relationship between mycorrhizal fungi (soil microorganisms) and plants; and evaluate the feasibility of establishing vegetation on mine waste by introducing mycorrhizae. Problems in Revegetation Successfully using vegetation to stabilize a situ disturbed by mining-related activities depends on knowing the chemical, physical, and biological characteristics of the site prior to, or at the time of, stabilization. The primary objectives of mine land reclamation are to minimize environmental degradation and to facilitate the re-establishment of a functional plant-soil system. Mining disturbances can significantly alter the physical, chem¬ical, and biological characteristic of a site, thus affecting plant establishment, survival, and growth. The physical disturbance caused by the removal and replacement of soil and overburden, together with the waste material from ore processing, affect the chemical, physical, and biological process within the disturbed soil or waste. Additionally, variability in soil properties results from differences in climate, topography, vegetation, and parent material of the site.

Jan 1, 1993

By David Hoadley, Kenneth R. Maser, Ashok B. Boghani, James E. Billar, D. Randolph Berry, Mackenzie Burnett, Robert H. Trent

SUMMARY AND CONCLUSIONS This report describes a study to develop a detailed set of guide¬lines and equipment recommendations to be used as a guide for mine operators, mine inspectors, and equipment manufacturers in implementing the emergency escapeway standards for metal and nonmetal underground mines. It was sponsored by the United States Bureau of Mines. The first part of this report reviews the historical background of metal and nonmetal mine fires and the development of present and proposed mandatory standards. This is followed by a discussion of the survey of representative mines and how the proposed standard effects these mines. The remainder of the report covers technical discussions of each escapeway component including a comprehensive computer sim¬ulation of mine evacuation. Following the technical discussion of each group of escapeway components is a list of the pertinent guidelines. A study of past mine fires indicates that a serious commitment by operators to the proposed escape standards would be instrumental in saving lives in the future. The most significant event in a recent mine fire, in which no deaths resulted, was the very early discovery of the fire. The evacuation was orderly thanks to careful preparation by the mine personnel. However, the mine was possibly only spared a real disaster because of the discovery of the fire almost at its inception. Installation of automatic fire and smoke warning devices may be the single most important step in preventing future disasters. The self-rescuer has saved many lives in mine fires. Men have also died while attempting to use them. The reason men died was either because the unit was not working or the miner did not understand how or when to use it. There is no good excuse for either of these conditions occurring. Regular maintenance and inspection should prevent unit failures. Frequent instruction on when and how to use the self¬rescuer would prevent confusion and potential fatalities. A means of

Jan 1, 1976

By R. V. Ramani, R. Stefanko, G. W. Luxbacher

1 11 THIS IS A DIGITAL COMPUTER SIMULATION OF THE VENTILATION SYSTEM OF A MINE LOCATED IN WASHINGTON COUNTY, PENNSYLVANIA. THE VENTILATION SURVEY ON WHICH THIS SIMULATION IS BASED WAS RUN FROM OCT. 27-30 AND ON NOV. 2, 1976 IN THE ACTIVE PORTION OF THE MINE INBY COMBS SHAFT AND THE INACTIVE PORTION AFCUND AND INBY DONAHOO SHAFT. FOLLOW-UP SURVEYS WERE THEN RUN ON FEB. 18 AND FROM MARCH 7-11, 1977 TO INCLUDE THE MAIN HAULAGE SYSTEM OUTBY THE ACTIVE AREAS OF THE MINE. ALL SURVEY DATA WAS NORMALIZED TO A STANDARD DENSITY OF 0.075 POUNDS/CU.FT. PRIOR TO THE CALCULATION OF INPUT PARAMETERS FOR THIS SIMULATION. IN THIS RUN, THE ORIGINAL VENTILATION NETWORK HAS BEEN MODIFIED TO INCLUDE NEW INTAKE AND RETURN AIRSHAFTS AT THE WEST MAINS.

Jan 1, 1977

By W. L. Staker

Alternatives were developed to the conventional ammoniacal carbonate leaching-steam stripping procedure for recovering copper as an oxide from contaminated scrap metal. By entraining air bubbles in the leach solution, the copper dissolution rate was increased to 1.5 g/in2 of copper surface per hour, compared to 0.5 g/in2/hr produced by conventional agitation in stirred tanks. Using entrained nitrogen gas bubbles for agitation in conjunction with powdered sulfur not only resulted in rapid dissolution but also simultaneous precipitation of the copper from solution as a high-grade cuprous sulfide.

Jan 1, 1971

To evaluate the potential for dust reduction, during blasthole drilling, of water or foam applied directly into the drill hole. Approach The Bureau of Mines tested a through-the-drill-steel water and foam injection technique in two noncoal mines to evaluate the method's potential for greater dust reduction. The tests were performed by drilling a series of blastholes for an entire face (a 90 minute time-period). For the first 45 minutes of drilling, foam or water was applied through the drill steel. Blowing ventilation was supplied to the entry about 50 feet from the face. The dust concentration measurements were made by a Real-Time Aerosol Monitor (RAM-I), and the data were read out on a strip chart recorder. The evaluation test results showed that the water or foam injection technique, when used on localized dust sources, can be an extremely effective dust control method. Small amounts of water used in this method have also allowed it flexibility to be used in water-soluble ores such as salt, gypsum, anhydrite, and trona. How The System Works Water or foam is mixed with compressed air (approximately 100-120 psi) with suitable metering systems and forced through the drill steel into the blast hole at the point of dust generation. Because the water or foam is applied at the source, minimal quantities of liquid are needed (0.2 to 0.6 gpm). These low flowrates are sufficient to just moisten the dust emerging from the blast hole, thus eliminating a major source of airborne dust. The wet drilling procedure also eliminates a second source of dust. With dry drilling, the dust from the blast hole falls to the floor. Since this can be a 15-ft drop or more, the impact can send the dust billowing up from the floor, adding to the airborne dust. With wet drilling, the moistened dust merely dribbles down the face.

Jan 1, 1982

By G. R. Friggens

A nuclear method for continuously monitoring the coalbed and ash levels and void formation in commercial-scale, fixed-bed, pressurized gas producers is proposed. Measurement of gamma ray transmission through the coalbed is the basis of the method. The coalbed level is monitored by detecting the trans-mission of gamma rays from a 1 to 2 Ci Co-60 source positioned on the outside wall of the vessel. Coal bridging or, alternatively, ash level is monitored by a 10 Ci Co-60 source at the center of the coalbed. Source activities and geometries are calculated for a 12-foot-ID producer designed to operate at 350 psi. Source capsule and detector specifications and operational safety are also discussed.

Jan 1, 1973

By Robert C. Hickman

"INTRODUCTION The Cline mine has been worked intermittently for copper and gold since 1895. Scheelite has recently been detected with the aid of a ""Mineralite"" on the old waste dumps of the mine. Four diamond-drill holes were drilled by the Bureau of Mines from August 13 to September 25, 1946. Results of this drilling showed the vein to pinch at depth and to carry no mineralization of economic importance.ACKNOWLEDGMENTSIn its program of investigation of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, does the actual investigation work, and prepares the final report. The Metallurgical Branch, Oliver C. Ralston, chief, analyzes samples and makes beneficiation tests.The project was under the general supervision of Mitchell H. Kline, chief, Raleigh Division, Mining Branch.Acknowledgment is due Dr. Jasper L. Stuckey, State geologist, for logging the drill core and to J. B. Zadra and associates, Metallurgical Branch, College Park, Md., for analytical determinations."

Feb 1, 1948

By Ivette E. Torres

Bulk carriers, freighters, and tankers are the three classes of seagoing vessels engaged in transporting mineral commodities. However, vessels in these classes are not exclusively devoted to mineral commodity transport. Bulk carriers move considerable tonnages of agricultural products as well as crude minerals, their concentrates, mineral fertilizers, and the like. Freighters, owing to their great variety, can be devoted wholly to hauling mineral products or wholly to nonmineral goods, as well as carrying mixed mineral commodities and nonmineral commodities. They include general cargo ships, full container ships, partial container ships, roll-on/roll-offships, and barge carriers. Tankers, although largely engaged in moving crude oil and refinery products, also transport liquid chemicals, molasses, wine, liquefied natural gas, and other fluids. Although physical characteristics of vessels such as size, draft, crew requirements, type of propulsion system, ratio of gross tonnage to cargo tonnage, and fuel costs have undeniable influences on shipping industry performance, problems of and changes in the quantity and types of materials moved also significantly affect the shipping sector of the world economy, and thus have a bearing on the minerals sector of that aggregate. Unfortunately, comprehensive global data reflecting changes in these critical variables are not published.

Jan 1, 1994

By R. H. Grau

Improving the air quality in metal/nonmetal mines is important in protecting the health of miners. Air quality can be improved in metal/nonmetal mines by developing proper ventilation techniques. Mine ventilation systems require stoppings to direct the airflow and establish pressure differentials throughout the mine. Due to their large size, stoppings in large-opening mines are cumbersome and costly to construct and maintain. As part of its mining health and safety program, the National Institute for Occupational Safety and Health (NIOSH) designed and tested two novel stoppings (Super Stopping and the EZ-Up Curtain Stopping) at its Lake Lynn Laboratory (LLL). The Super Stopping is designed as a long-term permanent stopping for use in the main entries of the mine, while the EZ-Up Curtain Stopping, although very durable, is designed more for portability and ease of installation. This paper describes the design, materials, and construction methods used for these stoppings as well as their performance and durability when subjected to tests simulating actual production face blast pressures.

Jan 1, 2006

By A. B. Cecala

A cooperative research effort was established between the Tilden Mining Company LC, the United Steelworkers of America, and the National Institute for Occupational Safety and Health to lower respirable dust levels in an iron ore grinding and concentrator plant. This cooperative effort involved three field studies to evaluate different techniques to lower respirable dust levels. The greatest impact on lowering respirable dust concentrations throughout this facility was achieved through ventilation changes. The most significant improvement was realized by changing the ventilation profile throughout the entire facility. The ventilation to this grinding and concentrator facility was provided by approximately 40 roof fans operating in either the intake or exhaust mode. The operation of these fans was significantly changed in an attempt to pro-vide more of a directional flow pattern throughout the facility, as well as to more closely balance the intake and exhaust air volume. This change accounted for a 31 pct reduction in respirable dust levels in the primary grinding area of the mill. Another successful modification was to improve the sealing of a reclaim tunnel to the outside and by barricading the access point from the reclaim tunnel to the concentrator plant. This minimized the dust liberated in the conveyor tunnels from traveling through the reclaim tunnel and into the plant. These two modifications illustrate the impact that improvements in ventilation can have on lowering respirable dust concentrations in iron ore processing facilities.

Compare the fire endurance of paneled steel stoppings with that of traditional concrete block Stoppings. Background Permanent stoppings or partitions arc used in mines to separate ventilation airways. The ability of stoppings to retain their structural integrity for a minimum length of time under lire conditions and prevent the spread of flame and toxic combustion products to an adjacent airway is critical. The success of miners in reaching safety during a fire depends largely on the presence of uncontaminated airways. Traditionally, permanent stoppings for coal mines are constructed of concrete blocks. Recently, paneled steel stoppings that satisfy many of the requirements demanded of permanent stoppings, such as incombustibility and strength, have been introduced. Their use also introduced concerns such as the ability of a steel stopping to maintain its ventilation control function when exposed to a fire and the potential that the fire could transmit enough heat through the stopping to ignite combustible materials on the unexposed side. To address these concerns, the Bureau of Mines investigated the fire endurance of galvanized steel and concrete block stoppings.

Jan 1, 1989

By C. A. Herbert

"The Bureau of Mines for a number of years has conducted experiments at its experimental mine near Bruceton, Pennsylvania, on the explosibility of coal dust, with particular reference to dust explosions in coal mines, and the knowledge so rained may well be applied to the handling of coal dust at industrial plants and elsewhere.Powdered coal is coming into use more and more as a fuel, and the dangers incident to its use should be recognized and guarded against, as a number of accidents have occurred in recent years due to ignorance of this danger or to carelessness.Within the past three years two very serious accidents, under almost identical circumstances, have occurred on the surface at two different coal mines in Southeastern Iowa, due in each case to the sudden ignition of a cloud of fine coal dust.The first accident resulted in the burning of six men, three of them fatally; the second burned eleven; three men died as a result of their burns.The mines in the Southeastern part of Iowa, where these two disasters occurred, are operating in a thin coal bed averaging about three feet in thickness, and are worked on the long-wall advancing system similar to that of Northern Illinois.The miners in this section are paid on a screened coal basis; in other words, receive no pay for the fine coal. As a result they use forks in loading the coal into the mine cars, and naturally a considerable quantity of coal is left along the roadways. Subsequently this fine coal, together with the roof rock that is taken down to give sufficient height on the roadways, is loaded into cars and dumped in piles on the surface. This roof rock is a block, oily shale and the contribution of fine coal and oil shale gives ample combustible material to thoroughly burn the rock as it is dumped."

Jul 1, 1923

Reduce injury to people or damage to equipment when a scheduled production blast is detonated. Approach The essential elements of an effective blast area security system were identified through case studies of five mining operations where the blast area guarding practices were considered to be superior to those generally found in the industry. These elements were used in making recommendations for improved blast area safeguarding practices. Background The blast area security system is a means by which the mine operator prevents injury to people or damage to equipment when blasting is performed. Analysis of blasting accidents showed that most blasting accidents occur during scheduled blasting and are due to inadequate blast-site security. Factors contributing to the system's breakdown are failure to clear the blast zone, inadequate guarding. and failure of personnel to follow instructions, retreat to a safe location, and/or take adequate cover. Mine personnel, visitors and even trespassers can inadvertently wander into a blasting zone unless proper procedures exist to ensure that all personnel are cleared from the blast zone and kept safely away until after blasting IS completed. Statistics show that the blaster is the miner most frequently injured In these accidents.

Jan 1, 1986

By J. R. Katan, J. R. Ball, Peter R. Bannister, F. J. Williams

During the last week in March and the first week in April, 1973, the Naval Underwater Systems Center measured the 76 Hz magnetic field strength (in Wisconsin and Texas) produced by both the elevated and (newly installed) buried Wisconsin Test Facility (WTF) north-south (NS) antennas. The principle result obtained from these measurements is that there is no measurable difference in performance between the WTF buried and elevated NS antennas.

Jan 1, 1973