Search Documents

To improve mining safety and efficiency by providing a practical way of detecting faults and channel sands that disturb coal seams. Approach A seismic system using a shallow blasthole has been developed and tested. How It Works A small shock is caused in a shallow hole, sending seismic waves through the ground. These waves are reflected from the top of the coal seam, acid are detected by a line of geophones on the earth's surface. Dampening of the seismic signals by channel sands and other discontinuities in the seam is detected and recorded. See Figure 1. The seismic shock wave can be produced by exploding small charges, dropping a weight, firing a gas gun, or actuating a vibrator. Depending on the soil cover, the shock is usually generated in shallow vertical holes about 10 feet deep. Hole depth depends on the soil mantle thickness because it is preferable that the seismic shock originate below that layer.

Jan 1, 1976

By W. S. Sanner

Grinding experiments were conducted to determine the finest anthracite particles that could be produced in a ball mill. Continuous and batch tests were run in a dry-grinding ball mill. Batch grinding produced the finest coal particles. They averaged 2.2 microns in diameter and were 99.0 percent smaller than 37 microns. Continuous grinding yielded a product 6.1 microns in diameter, with 96 percent smaller than 37 microns.

Jan 1, 1968

Provide an inexpensive, simple means of supporting highly yielding ground In underground mines. Approach The Bureau of Mines developed a high capacity support post made from standard steel pipe which, when using a 60-inch post configuration, has a 45-ton capacity and a yield length of 24 inches. How It Works The post mechanism is a three-piece unit consisting of a top and bottom leg (made from standard steel pipe) and a separate foot bracket. During installation in the mine, the bottom leg is placed on a relatively flat surface on the mine floor and the top leg is placed over it until its flared end contacts an expansion ring attached to the bottom leg. As the roof and floor converge, the flared end of the top leg is forced into the expansion ring, causing the walls of the top leg to be deformed radially and along the axis. The mechanism will yield until the unit bottoms out after about 24 inches of yield.

Jan 1, 1987

By Fun-Den Wang

A new approach for evaluating pit slope stability by the limiting equilibrium method has been developed by the Bureau of Mines. The finite element method of plane strain analysis is used to find the stress field of the pit slope structure. This stress field is then used to find the normal and shear stresses along a potential failure surface. The normal stresses are used with the Coulomb equation to calculate the shear resistance. The shear stresses are integrated to determine the total driving force. The factor of safety is evaluated from the ratio of the resisting force to the driving force along a failure surface, and is found to be affected by the elastic material properties, modulus of elasticity, and Poisson's ratio.

Jan 1, 1970

By B. J. Scheiner

Carbonaceous gold-bearing ores of the type that occur in north-central and northeastern Nevada were investigated by the Bureau of Mines as part of its Heavy Metals Program. Specific objectives were to identify the carbon and organic compounds that prevent adequate gold recovery from the ore by cyanidation and to develop an economical process that would overcome the detrimental effect of the carbonaceous constituents. Activated carbon and long-chain organic compounds containing sulfur and nitrogen were found in the ore. Part of the material consisted of stable gold organic complexes. A mild oxidation technique that allowed gold extraction as high as 96 percent by subsequent cyanidation was developed. A variety of oxidants was shown to be effective in improving gold recovery, including chlorine and sodium hypochlorite (NaOC1). An electrolytic oxidation process was developed that was particularly advantageous from an economic and effectiveness standpoint.

Jan 1, 1971

By L. J. Froisland

An integrated process for recovering metal from nonmagnetic auto-shredder reject scrap was investigated by the Federal Bureau of Mines. The methods used were air classification, water elutriation, screening, magnetic separation, handpicking, and heavy-media separation. Metal recoveries in this process were projected at 39 percent copper and copper alloys, 53 percent aluminum, 96 percent iron, and 98 percent zinc die cast. An economic evaluation of the conceptual process indicated that a facility designed to reclaim the reject scrap from 200 shredded automobiles daily could be profitable. Total investment in this plant was estimated at $321,000; the discounted rate of return before taxes was 53 percent.

Jan 1, 1975

By M. W. Von Bernewitz

Corduroy is used for saving gold in small Land large milling plants throughout the world. Investigations by the Metallurgical Division of the Bureau of Mine indicate that corduroy blankets, used with or without a trap or jig in the mill classifier circuit, often are effective in concentrating gold and sulfides, especially if the gold does not amalgamate readily and if not enough sulfides are present to warrant the use of a shaking table, flotation cells, or cyanide plant. Most cold-mining countries include several or many small miner, that produce siliceous ores low in sulfides and gold, which can easily be amalgamated or caught in traps or jigs or on corduroy and shaking tables. At these mines the ore is crushed by stamps or bill mills, and the flow sheets include plates, flotation cells, and cyanide treatment, yet probably nearly as much of the pair minerals may be recovered by the less expensive plant. A well-known western maker of mine and mill equipment asserts, as the result of considerable observation of installed plants, that old and other valuable minerals should be caught as soon as they have been released by a mill, end recommends jigs to do this. A supplier of corduroy has informed us that at some mines this material is being replaced by jigs that catch gold as fine as 400-mesh. But for the small operator, inexpensive equipment such as a corduroy table may be better adapted and give a good recovery of gold and associated minerals.

Jan 1, 1939

By Richard Hammer

Various alternating current (ac) methods can localize faults in mining power cables. Several methods considered by the Bureau of Mines in this report are the Murray loop for short circuits, wherein a bridge provides proportional distance to the fault; capacitance measurements for open conductors; inductance measurements for shorted conductors; phase comparison, high speed recordings of voltage and current in the faulted state are compared with normal voltage and current with the difference being a function of impedance change and impedance change being a function of fault location; and standing wave measurements, detecting the resonance of the length of cable to a fault (either short or open). Portable capacitance bridges are presently available for the second method, and the fourth method is well developed for use on large power distribution systems. Because it utilizes pulses rather than ac, the time domain reflectometer (TDR) method of fault locating was not included in this investigation. However, a comparative evaluation between this versatile method and the Murray loop might prove advantageous in locating high resistance faults.

Jan 1, 1977

By A. B. Hooker, L. C. IlsLey

The greatest hazard of early mining was from explosions of methane ignited by open lights . With the advent of safety lamps and forced ventilation this hazard was greatly reduced until the application of electricity to modern mining not only multiplied the sources of gas ignition but the accompanying , machines and haulage systems increased the amount of explosive dust , through which a methane explosion is more liable to become a major mine disaster , and thus greatly furthered the need of adequate ventilation to keep down the concentrations of methane . Adequate ventilation is still the best preventive of such explosions . However , even with a well laid out and controlled ventilating system the amount of air passing through entries and rooms is liable to vary within wide limits because of open doors , falls of rock , or other accidental causes . The percentages of methane under normal conditions should therefore be kept so small that they will not be increased to explosive proportions by short interruptions in ventilation . Mine ventilation and methane detection are inseparable safety precautions . The increasing importance of ventilation necessitates more accurato determinations of the methane concentrations throughout the mines . This paper discusses in detail some of the steps in the development of methane detection and specially notes the more accurate detectors now available . One of the earliest means of detecting methane was by a candle . About 1835 , John Buddle , Sr. , a noted mining man of his period , when questioned by a Parliamentary Committee as to the safety of using candles , replied :

Jun 1, 1933

Design a new acoustic monitoring system to more accurately forecast impending rock bursts, and to assist in understanding the rock burst phenomenon. Background Rock bursts arc the major cause of injuries and deaths in deep underground mines in the Silver District near Wallace, ID. Bureau investigations of the rock burst phenomenon resulted in significant improvements in computerized acoustic technology, and achieved limited success in forecasting several large events. Research demonstrated that the location of rock noise, and the rate at which these events occur, are indicators of areas that could fail violently. In minewide monitoring, the typical array of acoustic sensors (geophones) is arranged to cover an entire mine with 16 to 32 separate instruments. The mines intended to be covered may be 7,000 feet in depth and up to several miles in extent. While such an arrangement is capable of detecting and locating large seismic events (rock slippage along natural fractures or faults), the geophones are too far apart to accurately locate mining-induced events at the active workplaces. The Bureau devised a strategy to concentrate the geophones into typical slopes (mining areas about 200 by 500 feet) to record the rock noise in areas where the miners work. By using such a dense geophone array at a mine, the Bureau provided event location and rate information to mine operators who removed workers and ceased production from active mine areas that subsequently suffered rock bursts.

Jan 1, 1989

To concentrate coarse mica particles using a dry beneficiation technique. Approach Concentrate coarse, II berated mica particles using a Bureau-designed system of crushers, screens, and a two-stage zigzag air classifier. How It Works Because mica has a flat plate-like crystalline structure, mica particles are significantly lighter than blocky gangue particles of the same size fraction. Thus an air classification technique can separate the flat, light mica particles from the heavier gangue particles. The ore, which Is first run through a standard jaw crusher, a roll crusher, and a hammer mill to liberate the mica, enters the rougher Zig-zag section through a rotating air lock. See photograph and diagram of a 2-stage air classifier. Airflow through the classifier can be varied according to the size of the particles being separated. The gangue material falls through the airstream of the rougher zigzag section and is discarded as tailings. The mica flakes are carried by the air-stream to the cyclone shown on the right side of the diagram, where they are collected. This rougher mica concentrate is fed to the cleaner zigzag section through another rotating air lock. The mica particles are again carried by the airstream but they are now collected In the cyclone on the left side. The cleaner concentrate leaves the left-side cyclone through a third rotating air lock and is rescreened to remove under-size material missed by the first screening. The final product of this pneumatic process is generally a high-grade mica concentrate. A generalized flow diagram for the pneumatic concentration method Is shown In the second diagram.

Jan 1, 1981

By David A. Monaghan, Kenneth R. Maser, Adi R. Gurdar, D. Randolph Berry

SUMMARY The objective of this program was to develop a system to extinguish coal mine fires by remote sealing of the underground passageways. The system developed had to be versatile enough to function under a wide range of operating conditions, including large variations in passageway geometry, depth of mine, water conditions, both in the mine and at the surface, and rubble in the mine passage. The system developed had to include instrumentation for the remote probing of the passageway prior to sealing, a system for sealing the mine passages, and instrumentation for remote monitoring of the quality of the seal during and after construction. These objectives were successfully achieved during this program. The remote mine sealing capability of the system was satisfactc rely demonstrated in a field test conducted at the Eastern Associated Coal Corporation Federal No. 1 Mine in Grant Town, West Virginia. The remote sealing consists of: (1) A sonar initial probing system which can operate satisfactorily even in the presence of dense smoke. The system is capable of determining both the local passageway geometry, identifying the presence of cribs and other obstructions, and the position of the borehole in the mine passage. (2) A mine sealing material system which utilizes fly ash for making the complete seal or as a bulk filler in conjunction with a urethane, froth foam, seal topping system. The choice of using fly ash alone or fly ash with foam topping depends on a number of factors, such as quality of seal desired, time available per seal, depth of borehole, passageway geometry, and water holding require¬ment. The fly ash-foam seal is a better seal, capable of sealing against a higher water head than fly ash alone. The fly ash sealing

Jan 1, 1973

Provide the mining industry with a wireless surveying system for increasing efficiency in the drilling of methane drainage or exploration boreholes. Approach The Bureau of Mines has pioneered the technique of methane control by drilling long, horizontal drainage holes from within the mine complex. It was recognized during the early drainage projects that a major portion of the drilling operation was dedicated to hole surveying. In some cases more time was actually being spent on the surveying operation than on drilling. The large amount of time required for hole surveying was the result of having to pump an instrument to the bottom of the hole, then retrieve it with an attached wire line. Naturally as hole depth increased, so did the amount of time needed to perform the survey operation. If the survey operation could be improved it was obvious that overall efficiency in drilling of long, horizontal methane drainage holes would be greatly increased. The Bureau of Mines, therefore, developed, fabricated and tested in an operating coal mine a permissible wireless survey system specifically designed for small diameter methane drainage drilling. The prototype survey system was completed in 1982 and was given the IR-100 Award by Industrial Research and Development Magazine. A second generation survey system is currently being constructed using updated state-of-the-art electronic technology. The second generation system will be more portable, more reliable, easier to maintain, and less costly.

Jan 1, 1984

Control respirable dust in underground coal mines through selection of optimum water spray pressures. Approach Through underground trials at longwall and continuous mining operations, the relationship between operating water spray pressure and respirable dust levels at the machine operator's location was determined. Defining the Application Water sprays are used for two significantly different control applications. On longwall mining machines, sprays are commonly installed both on the body of the machine and on the cutting drum. Sprays on the body of the machine are used to redirect dust which has already become airborne away from the machine operator. Each spray acts as a small fan, directing the primary airflow over and around the machine and towards the face, away from the operator. The energy of this system is directly related to the spray pressure. Higher pressures move more air, but care must be taken not to cause turbulence and boilout into the walkway. Sprays mounted on the drum are, effective at suppressing the respirable dust at the bit/coal interface and preventing it from becoming airborne. Again, these sprays must not impart excessive energy to the dust particles thus stirring up more dust than they suppress. While mounting sprays on the shearer drum is standard industry practice, there is no reliable technology available to successfully mount water sprays on the cutting drum of continuous miners. Instead, sprays are mounted on the machine body, close to the drum, and directed at the cutting head. This allows the water to reach the bit/coal interface and mix with the cut material. Here again, care must be exercised to prevent these sprays from imparting excessive energy to the dust particles and stirring up more dust than they suppress. These sprays can also cause dust "rollback" from the face, toward the operator, if operated at too high pressures.

Jan 1, 1986

By Donald J. Barnes

Gold was found in samples collected from Pleistocene and Holocene stream and terrace deposits. Approximately 15,000 cu yd (11,400 cu m) of small and discontinuous terrace and stream gravel deposits in the study area are composed of material derived from sedimentary and granitic rocks. The detritus is subangular to subrounded, and poorly sorted, ranging from boulder to sand size. Gold values in samples collected averaged 8.2 cents per cu yd (gold value of $500 per oz). Pan concentrates and rock chip samples collected from reported mineralized zones showed an absence of economic minerals. Stream placer deposits are uneconomic. No potential was observed for metallic or nonmetallic minerals in the La Panza study area. No potential exists for gas, oil, or coal resources.

Jan 1, 1981

Reduce the costs associated with conventional treatment of acid mine water. Approach Conventional treatment of acid mine drainage consists of plants requiring large mixing and aeration tanks, mechanical aerators and large, shallow settling ponds. Such plants are usually very costly to construct, maintain and operate. The Bureau of Mines has developed a simple, low-maintenance, highly efficient system to treat acid mine drainage which mixes, aerates, and neutralizes mine water Simultaneously in the existing discharge pipeline by using the pressure generated by the deep mine discharge pumps. The mixing and aeration action of the in-line system significantly increases oxidation rates of ferrous iron. Iron and manganese are removed, even at near neutral pH levels, due to the high efficiency of this system. How It Works The In-line Aeration and Treatment System (ILS) consists of two commercially available components, a jet pump (ejector) and a static mixer. The jet pump is simply a nozzle that converts water, already under pressure, into a high-velocity stream that entrains air by Venturi action. If neutralization is required, sodium hydroxide or lime is added along with the air at the Venturi opening. The aerated and neutralized water then enters the static mixer, which is a length of internally spiralled pipe that mixes air and water together. The two components, which are both about 8 feet in length, replace the last section of discharge pipe at a point before the mine water is emptied into a pond. Along with the settling pond, these components treat the water so that it meets discharge criteria. The system has been used at surface drainage treatment facilities as well, but in such use a pump is required to provide the necessary pressure drop across the Venturi opening.

Jan 1, 1985

Objective Develop field measurement and computer modeling methods to predict the potential for hang-ups and structural failures in underground mine ore paws. Background Analysis of Mine Safety and Health Administration (MSHA) accident statistics has identified ore pass hazards as a significant safety problem in underground metal mines in the United Stales. Recent ore pass failures have underlined the lack or ore pass design methods ant1 standards available to both MSHA and mine engineers. Injury and fatality data for the 20-ycar period between 1975 and 1095 show that nearly 75% of the injuries were directly or indirectly related to pulling or freeing ore pass chutes, the use of hand tools, falls or broken rock, and structural failures or chutes or gates and ore pass walls.

Feb 1, 1998

Reduce longwall intake contamination by controlling respirable dust generated by the stage loader. Approach Install a water-powered scrubber on the stage loader immediately outby the crusher. Dusty air from the crusher is drawn through the scrubber and a clean air discharge is delivered into the primary face airflow. How It Works The contamination of intake air is a significant dust control problem often overlooked on many longwall faces. This dust source contributes to the full shift dust exposure of all face personnel, and thus can significantly affect compliance with Federal regulations. Several sources contribute to contamination; however, dust generated by the stage loader crusher is the single largest source. The breaking action of the crusher generates a tremendous quantity of dust, which mixes with the primary ventilation airstream and is carried down the entire length of the longwall face. The installation of a water-powered scrubber (see diagram) has proven effective in controlling crusher-generated dust. The scrubber is mounted immediately outby the crusher. A duct is placed over the scrubber intake and attached to a flanged opening over the crusher discharge. In

Jan 1, 1982

By E. J. Gleim

In April 1932, the Bureau of Mines published Information Circular 6595, entitled "Data in Reference to Installation of Cables in Shafts and Boreholes", in which were described methods followed in various sections of the United States when electrical circuits are taken into mines by means of cables suspended in shafts and boreholes. In view of the present tendency to extend high-tension cables along entries and passageways from the bottom of the shaft, borehole, or other point of entrance to coal mines rather than over the surface, it is deemed that the various methods of installing such cables deserve careful consideration, particularly in mines in which gas and coal dust contribute to explosion hazards. This is especially true of localities where there is an inclination to restrict the extension of 2,300- and 4,000-volt circuits into the mines. Probably it is feared that accidental contact with the cables of such circuits may result in more serious shock than with lower voltages; also, it is possible that new circuits are regarded merely as explosion hazards additional to those already existing, regardless of the manner in which the new circuits may be installed. It is the firm belief of some engineers that the circuits can be installed so that they will not be damaged by wrecks or roof falls, thereby eliminating the hazard of explosion from this source while at the same time making the chance of accidental contact remote if not impossible. Moreover, some believe that fire hazards from direct-current systems can be reduced by keeping motor-generator sets close to load centers. Thus, although the alternating-current circuits would be lengthened, the size and extent of direct-current circuits would be kept to a minimum.

Jan 1, 1939

By J. F. Barkley

"In the course of the Government's Fuel Economy Survey of its own power plants, studies and tests have been made of various oil-burning equipments under power-plant boilers. There are now many types of burners being offered in the relatively limited field of power-plant use. The majority of the types used may be grouped into two general classes- those using steam to effect the atomizing of the oil, and those using mechanical means.Burners using steam have had the most prominence in this field for a long period. The mechanical atomizing type of burner successfully applied on shipboard, however, pointed to a possible betterment in land work. The vision presented itself of a burner that would need no steam for atomizing that would permit of air inlets or registers compactly arranged as a part of the entire burner, and that would only require the natural stack draft usually available in land boiler furnaces. Hence, rather recently there has been much development along this line, resulting in various types of burners.In Table 1 are grouped test items chosen from many tests showing representative analyses of the products of combustion obtained with various burners installed in various types of furnaces. In all these tests the burners were handled by experts and represent practically the best attainable for that particular arrangement. The boiler efficiencies ranged from 70% to 80%. It will be noted that the burners using steam for atomizing were able to secure slightly better 002 and less 02 without the presence of CO."

Feb 1, 1926