Search Documents

By Robert P. Vinson, Fred N. Kissell

This report describes three coal mine ventilation studies by the Bureau of Mines in which sulfur hexafluoride (SFG) was used as a tracer gas. One of these studies was conducted to determine air movement and leakage in a sealed area. Another was run to determine the ventilation efficiency of a bleeder system. Finally, a study was made of air leakage across permanent stoppings of parallel intake airways. These studies proved sulfur hexafluoride to be a useful addition to the equipment commonly used in coal mine ventilation analysis.

Jan 1, 1976

Provide an accurate, simple, alternative means of evaluating the safety of mine electrical ground systems which has little or no negative impact on mine productivity. The Traditional Evaluation Method The Code of Federal Regulations requires all mines to safely ground their power systems to earth. Effective earth grounding reduces shock hazards to mine workers operating electrical equipment, protects equipment from damage by voltage transients, and provides a means of detecting and locating ground faults. Once an earth ground bed has been constructed, its level of resistance has traditionally been used to gauge the safety of the entire grounding system. Bed resistance measurements are normally performed using a ?fall of potential? technique with a current return electrode placed at a remote location, If the resistance measured is acceptably low, then the bed is assumed safe.

Jan 1, 1985

Provide a method for obtaining in situ measurements of coal cutting forces which are needed for mining machine design. Approach A portable in-seam testing device is carried to the face of an underground coal mine heading to measure the cut-ting force encountered by a continuous miner pick directly at its maximum depth of cut. How It Works The tester frame is attached directly to the coal surface with four one inch diameter threaded studs resin-bolted into 1-1/4 inch diameter holes which are drilled 30 inches deep. Spherical nuts and washers compensate for misalignment between the bolts bearing plate, and traverse beams. Spacers can be placed over the studs to assure that the traverse beams remain in the same plane. Cutting forces are applied by a hydraulic cylinder that moves the pick of the tester through a twin-chain arrangement which gives a 20-inch cutting stroke with

Jan 1, 1982

GLOSSARY Acid- and toxic-forming materials. Rock or coal layers containing significant amounts of pyrite or other minerals which, if exposed by coal mining, will cause acid or toxic drainage to occur when acted upon by air and water. Add mine drainage. Any water with a pH less s than 6.0 draining from a coal mine. Water is often orange-colored because of the presence of oxidized iron. Adit. An underground mine entry at sites where coal seams are exposed at ground level. Apple core. A complete hilltop (360°) left exposed by not backfilling the highwall. Approximate original contour. The surface configuration achieved by backfilling and grading the mined area so that be reclaimed land closely resembles the general pre-mining surface configuration and blends into and complements the drainage pattern of the surrounding terrain. Area mining. A surface mining method that is carried on in level to gently rolling topography on relatively large tracts of land. Active area mine pits may be several miles long. Arid and semiarid regions. Lands, generally west t of We 100% meridian, where water use by native vegetation equals or exceeds that supplied by natural precipitation, and rainfall is insufficient to support agriculture. Annual precipitation is normally 20 inches or less. Auger mining. A mining technique often used by surface mine operators when the overburden becomes too for the coal to be mined economically using traditional surface mining methods. Large-diameter (usually 2'-4') horizontal holes are drilled as much as 300 feet into We vertical Me of the coal bed by an auger. Like a bit used for boring holes in wood, coal augers consist of a cutting head with a screw-like extension. As the auger turns, the head breaks up the coal and the screw carries it back into a conveyor that loads it directly into a truck. Backfilling. The operation of refilling an excavation using material removed during the mining process. Bench. The level or flat working area at the base of the highwall that is excavated between the exposed coal seam and the original surface of the ground. Bucket wheel excavator. A continuous-digging machine that uses a rotating vertical wheel with buckets for large-scale stripping and excavating. Cessation Order. Order to cease mining issued to a coal operator by the regulatory authority due to severity of violations, Contemporaneous reclamation. Restoration of mined land that occurs as soon as practical after coal removal. Contour mining. A mining method commonly used in eastern mountainous topography where coal is removed in a narrow strip around the hillside. The extent of the cut into the hillside is determined by the depth of overburden at the highwall compared with the thickness of the coal seam. Daylighting. A term used to describe a surface mining procedure that exposes abandoned underground coal mine workings to enable removal of the remaining coal. Daylighting is followed by land reclamation. Dragline. An excavating machine, usually used in large, flat areas, that drags a bucket (which holds up to 220 cubic yards of material) toward the machine by cables, loads it with spoil, and then hoists it wit a boom up to 350 feet long, allowing the machine to excavate wide benches by depositing the spoil hundreds of feet away from the highwall. Grading. The process of smoothing the disturbed areas of the mine site, after the coal is removed, to closely approximate the pre¬mining terrain. Haul road. Any road constructed, improved, maintained, or used by mine operators and located within the permit area. Head-of-hollow fill. See "valley rill." Highwall. The cliff-like excavated face of exposed overburden and coal in a surface mine. Hydroseeding. Planting of seed mixed in a water medium. Water, mulch, lime, fertilizer, and seed are blended and sprayed onto regarded soil.

Jan 1, 1992

By Mark S. Sanders

The purpose of this work was to develop and field test improved knee protection for underground coal miners working in low seam mines. In a previous phase of this contract (Sanders, 1982), experimental knee pads were developed and field tested. The field test revealed several design deficiencies with the knee pads, and suggestions for improving the design were made. The work summarized in this report, therefore, consists of modifying the design and method of fabrication of the knee pads originally describes by Sanders (1982), and of field testing the improved design. The new prototype was shorter and wider than the original design, and used a neoprene pass-through strap design rather than a cloth strap molded into the pad itself. The new prototype was constructed by slush molding a hollow bladder that was then filled with foam. Initial reactions to the pads in the field test were very positive. However, after two months, the opinions about the new prototype became less positive. They were judged, generally, to be no better or worse than the pads usually worn by the field-test participants. Problems were encountered in the field with respect to durability. Water seeped into the inner cavity of many of the pads and caused the foam to deteriorate. It was concluded that it would not be cost-effective or feasible to significantly improve upon current commercially available knee pad designs.

Jan 1, 1986

By E. J. Kloos

Bureau of Mines-approved self-contained breathing apparatus of the compressed air demand type were evaluated for performance at low temperature. Apparatus durations, breathing resistances, and airflow rates were measured on machine tests at room temperature and -25° F. Man tests under actual wearing conditions verified the machine test results. Many serious functional changes in apparatus performance occurred at low temperature. Pressure regulators malfunctioned when diaphragms lost flexibility. Under certain conditions frozen condensed moisture sealed exhalation valves and fogged eyepieces. High-pressure leaks, not encountered at ordinary temperature, developed at low temperature. Tests results are discussed generally and specifically for each apparatus. Recommendations are given to obtain optimum performance from demand type breathing apparatus at low temperatures.

Jan 1, 1968

Aluminum alloys are used in two broad classifications: wrought and cast. Wrought alloy products, which are formed into final shape by rolling, forging, extruding. etc., contain low percentages of alloying elements; whereas cast aluminum products, which generally are not worked before use, may contain higher percentages and a somewhat different selection of alloying elements. For example, wrought aluminum alloys usually contain less than one percent silicon and cast alloys contain as much as 18 per-cent silicon. While there are good techniques available for separating aluminum alloys from mixed scrap, there are no efficient ways to separate wrought aluminum from cast aluminum. The high levels of silicon, iron) copper, and zinc from the cast alloys make wrought-cast mixtures unacceptable for wrought alloy production. Consequently, separated wrought aluminum scrap commands a premium price on the market. Since increasing amounts of mixed aluminum alloys are being recovered from automobile scrap, this separation is important for efficient recycling of these alloys. Approach The difference in thermo-mechanical properties between the two classes of aluminum alloys is used as the basis for the separation process. Casting alloys lose their ductility within a certain temperature range while wrought alloys remain ductile. As temperature increases, aluminum alloys gradually become weaker, and at a certain temperature, each alloy loses strength and ductility due to incipient melting in localized areas. For casting alloys that temperature generally lies between 520° to 560° C, but it is above 600° C for most wrought alloys. Mild crushing, therefore, in the proper temperature range will result in complete fragmentation of the casting alloys but only plastic deformation of the wrought alloys. A simple screening step then is used to separate the oversize wrought pieces from the fragmented cast alloys.

Jan 1, 1984

By D. L. Paulson

The Bureau of Mines is investigating pyrometallurgica1 and" chemical methods to recover valuable constituents from metallurgical dusts and slags. Under this program a technique was developed to recover iron from molten copper smelting furnace slags by carbon injection. Slags from gas-fired reverberatory and electric copper smelting furnaces were treated in an 800-kva electric-arc furnace by injecting coke breeze into the bottom of the molten bath. Over 95 pct of the iron and over 90 pct of the copper contained in the smelting furnace slags were recovered, while up to 85 pct of the carbon injected into the system was utilized. It is anticipated that the metal product containing approximately 95 wt-pct iron and 2 wt-pct copper will be a satisfactory medium for recovering copper by cementation.

Jan 1, 1977

By Robert L. Thorne

Cassiterite deposits on Sullivan Creek in central Alaska were investigated by the Bureau of Mines in the spring of 1943. Gold miners in the area have been recovering cassitorite each season as a byproduct of gold placer operations. Approximately 300 tons of tin concentrates have been shipped from the district. The deposits were sampled though trenches and small shafts. An average tin content of 0.28 pound per cubic yard was indicated. A detailed description of sampling methods and sample analyses is presented in this report.

Jan 1, 1948

By Peter F. Steidl

As part of the Bureau of Mines methane control program, the Upper Free-port coalbed was studied in Fayette County, Pa., where this coalbed lies about 650 feet below the Pittsburgh coalbed and contains the largest remaining reserves of any coalbed in the county. Its estimated recoverable reserves in Fayette County are between 670 and 800 million tons. Coal and overburden isopachs, structure and joint pattern maps, and a fence diagram were prepared using data from gas and oil exploration logs and coal outcrops. These maps will aid in determining the need and/or feasibility of degasifying the Upper Freeport coalbed in the study area. Much of the coalbed in this area is under 600 to 1,400 feet of overburden. By correlation with data from the Pittsburgh coalbed, the gas content at depths of this order is estimated to be between 140 to 300 cf/ton of coal.

Jan 1, 1977

By I. L. Nichols

Laboratory characterization studies have investigated the processing variability of carbonaceous uranium-bearing materials found in-sandstone deposits. This work was conducted by the Federal Bureau of Mines in support of its goal to maintain an adequate supply of minerals to meet national economic and strategic needs. Conventional processing produces only partial uranium recovery from these ore materials. Ore samples from New Mexico, Texas, and Wyoming were examined, and each responded differently. Using direct acid leaching techniques, some of the ores required acid additions of only 50 pounds per ton, while others required 300 pounds per ton of material. Maximum extractions ranged from 83 to 94 percent in the six ores tested. Roasting those ores prior to leaching improved extraction of the uranium to the 90 to 99 percent range. An oxidative autoclave treatment used with five of these ores resulted in extraction of 78 to 97 percent of the uranium. The experimental studies also showed that some carbonaceous materials can be concentrated by froth flotation. The flotation tailings were amenable to acid leaching, and up to 98 percent of the uranium was extracted from this type of material.

Jan 1, 1979

Reduce the noise radiated by the auger miner cutting head (typically 105 dBA at the face) by 10 dBA without compromising the durability or productivity of the tool. Approach Research was conducted by the Bureau of Mines to identify the noise sources of auger miners with emphasis on the cutting head and coal cutting process. The overall noise level generated by the coal cutting process was found to depend greatly upon the structural characteristics of the auger cutting head. Based on this information, a quieter cutting head was

Jan 1, 1982

By Ernest E. Fairbanks

[Microscopic methods have proved to be valuable assets in the study of low-grade ores. While the chemical assay u a ally discloses tine total content of valuable metals in such an ore, a thorough knowledge of the nature of the ore should form the from which to prepare an efficient means of recovery. In the treatment of low-grade ores, inefficient recovery, as indicated bay the amount of valuable mineral permitted to go to waste in the tailings, is too frequently the rule rather than the exception, As methods of recovery become more efficient, many low-grade 10 mineral A posits suddenly assume o commercial significance, In much of this material the minerals are so finely disseminated and intermixed that identification even by microscopic methods is a difficult matter. The application of microchemical qualitative analysis with the aid of new device described in this paper, will solve many of the problems of identification encountered in the study of low-grade potential ores. In these ores, especially, the limitations of ordinary microscopic methods are liable to become very great. The microchemical tests obtained by applying a standard set of reagents to a polished knoting whether or not a tarnishing action develops, have considerable value but arc far from being infallible. It is well-known that electrolytic effects are apt to affect seriously the diagnostic value of the tests, end this effect is encountered much more frequently in dealing with finely desseminated minerals. resort to microchemical qualitative analysis, therefore, becomes indispensable.]

Jan 1, 1924

By A. Z. Dimitroff

An improvised rock- dust disseminator, consisting of a 10-gallon galvanized metal milk can that dispenses rock dust in return air currents by the injection of compressed air has reduced the float dust explosion hazards at the Koehler coal mine, Koehler, N. Mex.

Jan 1, 1965

By Ronald S. Conti

Fire is a major concern for those who work in underground mines. A mine fire can occur at anytime and often results in a partial or total evacuation of mine personnel and could result in the loss of lives. Therefore, having a workforce that is well trained to prevent, detect, and fight a fire is important. This paper focuses on responders’ preparedness for fire. Responders in this context are considered the entire workforce and are categorized as first, second, and sustained responders and evacuating miners. Quality training enhances ones awareness of mine fire hazards and promotes self-confidence in combating fires and responding to emergencies. Early warning systems and other escapeway aids such as a through-the-earth signaling and communication system, lasers and strobe lights are also addressed. The technological advancements that have been made can improve the state-of-preparedness for responders to underground emergencies and increase the chances of survival for escaping personnel.

By Richard J. Bielicki

Poor mixing of methane and air at coal mine working faces causes fluctuating methane concentrations. If these fluctuations are large enough, methane levels can periodically exceed safe limits, even though the time average methane concentration may be satisfactory. Concentration fluctuations measured underground can result both from variations in methane emission rate and poor mixing. The present paper reports on a statistical analysis of fluctuations at a constant methane emission rate, that is, on fluctuations due only to poor mixing. A full-scale model of a working face was used. Both peak heights and elapsed times between peaks were evaluated. Good mixing was indicated by normal, Poisson, and exponential distributions while poor or incomplete mixing was indicated by log-normal or gamma distributions.

Jan 1, 1974

By Ronald D. Hill, Elmore C. Grim

Mining as an extractive process alone is outdated and unacceptable to today's environmentally concerned public. Multiple land use must be considered as well. Only through effective preplanning can the full potential of reclamation result in a lasting asset for future generations. The coal industry is now recognizing that reclamation of mined lands is part of the mining cycle that must be planned and carried out in a timely and orderly manner. It is also finding that planning reclamation in advance of mining is cheaper and more effective than waiting until mining is completed. The decision to open a strip mine must be based on the results of studies to determine if successful reclamation can be achieved and whether the economic benefits to the company will be justified(1). Information regarding the physical, chemical, hydrologic and biologic systems operative at the site must be under- stood or reclamation will be a failure. Working together, engineers, management and reclamation specialists should design the actual mining and reclamation plan before mining is begun.

Jan 1, 1974

By John Nagy

Limited experiments in the laboratory with specimens of mine rock from a Virginia bituminous coal mine indicate that natural gas-air mixtures can be ignited by sparks generated by rubbing friction of sandstone against sand-stone, shale against sandstone, sandstone against (roof-bolt) steel, and shale against steel. Such sparks, generated during a roof fall, may have initiated a recent gas explosion in this Virginia mine, although this cannot be stated with certainty. No ignitions of gas were produced by sparks or heat generated by impact friction between mine rocks or steel, during tension breaks of roof bolts, or by pull tests of roof bolts through their washers and roof plate. However, this negative result of limited experiments does not preclude the possibility of gas being ignited by these conditions.

Jan 1, 1960

By J. B. Gayle

Numerous investigators have studied the addition of inert4 substances to coking blends. Generally, the results have yielded trends applicable only to the particular coals and inerts studied. Recently, somewhat more general results were obtained for cokes produced from blends containing added inerts, using the sole-heated oven. The present investigation represents an extension of this work to include a wider range of inerts and to determine the applicability of the various conclusions to cokes produced with the Tuscaloosa oven. The results indicated that an increase in dry-coal charge density of 1 pound per cubic foot (p.c.f.) caused a corresponding change in the hardness (1/4-inch tumbler index) of Tuscaloosa oven cokes of 0.9 percentage points. This value compares favorably with the value of 0.7 determined previously for the sole-heated oven and Bureau of Mines-American Gas Association (BM-AGA) retort.

Jan 1, 1961

By W. E. Robinson

Oil-shale samples selected from a core of the Green River Basin (Wyoming) were studied to ascertain differences in the composition and/or chemical structure of the organic material in the samples relative to stratigraphic position within the Green River Formation. This involved a systematic study of the soluble organic material and the insoluble kerogen present in the samples. Emphasis was placed upon the distribution of the alkanes (normal and isoprenoid compounds) in the soluble extract and upon the aromaticity of the kerogen. In general, it was concluded that significant differences exist in the chemical structure of the oil-shale organic material from various strata within the Green River Formation of Wyoming. Most of the compositional and structural changes were not related to burial depth but were related to source material variations, environmental differences, or other factors.