Search Documents

The Technical Study Panel on the Utilization of Belt Air and the Composition and Fire Retardant Properties of Belt Materials in Underground Coal Mining (hereafter referred to as the Panel or the TSP) was established by Section 11 of the Mine Improvement and New Emergency Response Act of 2006 (MINER Act). The Panel was charged with providing “independent scientific and engineering review and recommendations with respect to the utilization of belt air and the composition and fire retardant properties of belt materials in underground coal mining.” The TSP was impaneled by the Honorable Elaine L. Chao and commenced its work on January 9, 2007. At this first meeting, Mr. Richard E. Stickler, Assistant Secretary of Labor for Mine Safety and Health, asked the Panel to report on many issues including how recent technological advances could be applied to atmospheric monitoring systems, point-type heat sensors, current state of fire-resistant vs. fireproof belt materials, and belt fire suppression systems to improve miner safety. In addition, Mr. Stickler asked the Panel to review belt air velocity limitations. The Panel members attended 12 days of public meetings over a nine-month period. Three of the public meetings were scheduled for the Panel to hear from technical experts and those persons or organizations interested in providing input. The meetings were held in Coraopolis, Pennsylvania with emphasis on belt fires, belt maintenance, belt flammability and toxicity, ventilation, and escape issues; in Salt Lake City with emphasis on ground control and convergence issues; and in Birmingham with emphasis on fire detection, sensors and atmospheric monitoring systems. National Institute for Occupational Safety and Health (NIOSH) researchers, Mine Safety and Health Administration (MSHA) personnel, representatives of the major belt conveyor manufacturers and a representative of the National Mining Association provided discussions at the Coraopolis meeting. In Salt Lake City, Utah, MSHA district managers and ventilation specialists, a member of the Aracoma Mine No. 1 investigation team, a representative of the Bureau of Land Management, and industry and consulting representatives of the Utah Mining Association and the Colorado Mining Association made presentations. In Birmingham, Alabama, atmospheric monitoring system representatives, NIOSH researchers, representatives of coal mining companies, and UMWA workers from two Alabama mining companies made presentations. In addition, a staff member of The Center for Regulatory Effectiveness also presented comments to the Panel. In conjunction with the meetings in Salt Lake City and Birmingham, three-member subcommittees of the Technical Study Panel made field visits to the Skyline Mine, the Aberdeen Mine, and the Jim Walter Resources Mine No. 4. The mine visits were scheduled to see first-hand the mining conditions under which belt air was being utilized as an additional source of intake air for working sections.

By Árpád B. Palotás, Adel F. Sarofim, John B. Vander Sande, Paolo Ciambelli, Lenore Rainey

"The evolution during oxidation of the internal structure of soot and carbon black particles was studied using high-resolution transmission electron microscopy (HRTEM) and an image analysis system. Increasing ordering to the carbon structure with increasing oxidation is observed. Measures of the increased order are increases in the fractional coverage of a cross section of the particles with a layered structure, a decrease in the mean interlayer spacing, and a decrease in the spread of the interlayer spacing. The changing structure of the carbon black impacts its properties, such as the rate of oxidation.There is considerable interest in the study of the structural changes of carbonaceous materials as a function of oxidation. Davis et al.1 measured the variation of carbon dioxide surface area of various coals as a function of residence time in a flow reactor. HRTEM measurements revealed that crystallite dimensions and interlayer spacings are altered by combustion. Ishiguro et al.2 showed that oxidation alters the structure of diesel soot. The aim of our current research is to develop a better understanding of the microstructural reordering of carbon blacks with implications to their properties. The carbon blacks used in this research have already been studied and their reactivities as a function of oxidation measured.3The methodology used in this work has already been described in detail elsewhere.4 This paper presents an application to quantify the structural changes of carbon black particles as a function of oxidation and graphitization. The technique used is based on the use of HRTEM (high-resolution transmission electron microscopy) and computational image analysis.It is well-known that carbonaceous materials like graphite, soots, coals, chars, etc., possess characteristic structural appearances which can vary from mostly random or amorphous to a perfectly ordered graphitic crystalline structure. The carbon structure has been variously described as turbostratic5 or as crumpled sheets6 to indicate that parallel layering, reminiscent of graphite, is observed over dimensions of nanometers but that these planes or crystallites show disorder over larger scales. The degree of order of such structures is strongly dependent on the thermal treatment of the material as well as the composition of the source of the carbonaceous material. The value of electron micros¬copy in studying the morphology of such materials has been well established,2,7,8 although only a few attempts toward quantification have been made.The sample observed was carbon black CB330 from De¬gussa. One set of carbon black samples were oxidized in a thermo-gravimetric analyzer (TGA) in air at 575 0C, so that the conversion varied from 0 to 96%. Another set of carbon black samples were graphitized (Graphpac-GB by ALLTECH) and then oxidized in the TGA at 680 °C until 92% burnout was reached. The latter samples are called GB 0% and GB 92%, respectively.For the HRTEM observation a small portion of each sample was ultrasonically dispersed in ethanol. The suspension was deposited dropwise on a copper TEM grid coated with a lacey carbon film. The examination of the samples was carried out on areas that extend over the holes in the supporting film in order to avoid interference from the amorphous carbon background film An oriented gold crystal was used as a calibration standard and subjected to the same techniques as the carbon black samples."

Jan 1, 1998

By F. Garcia, J. Cervik

The cross-measure borehole technique has been shown by the Bureau of Mines to be an effective method of controlling methane liberated by fracturing the roof strata in longwall gobs where overburden is less than 750 ft (229 m). Boreholes are drilled into roof strata before mining operations affect the roof strata. Longwall mining fractures the roof strata and releases methane from source beds. Surface exhausters or vacuum pumps are used to draw the gas to the surface through an underground pipeline and vertical exhaust hole. The captured methane is thus prevented from entering the mine's ventilation system. About 71 pct of the methane produced by longwall mining in the Lower Kittanning Coalbed was captured by the cross-measure boreholes. Borehole spacing is an important factor affecting the performance of the technique. Interference tests and measurements of methane flows in return air indicate borehole spacing in the Lower Kittanning Coalbed should be limited to about 200 ft (61 m) except on the first 600 ft (183 m) of the longwall, where spacing should be reduced to about 100 ft (30 m) to capture the large quantities of methane released when the first large roof fall occurs. Comparisons between measured and calculated gas pressure differentials on boreholes indicate borehole length can be reduced from 280 to 140 ft (85 to 43 m), which reduces drilling costs significantly. Additional experimentation is necessary to verify the calculations.

Jan 1, 1985

By G. R. Hopkins

"A new record in fuel efficiency at petroleum refineries was achieved in 1935, when an average of only 615,000 B. t. u. was needed to refine a barrel of crude oil, compared with an average of 638,000 B. t. u. in 1934 and 829,000 B. t. u. In 1925. (See fig. 1.)Refiners have made almost uninterrupted progress in firing efficiency during the last decade although much of this gain was brought about by improved technique and greater use of heat exchangers and pipe stills, the determining factor was the trend in crude runs to stills. Most plants can increase their crude throughput materially with but small increase in fuel consumption. Consequently, in years in which crude runs have increased substantially, average requirements have declined; but in years in which crude runs have decreased, the average has tended upward. This conclusion is confirmed by figure 1, which shows that there has been but one minor exception to this rule in the last 10 years.Technical progress in fuel efficiency may be illustrated by comparing crude runs and total B. t, u. consumed. Between 1925 and 1935 crude runs to stills increased 31 percent, but the total quantity of heat required did not increase; in fact, it declined slightly.The trend of modern still construction is from shell stills, in which a large body of oil is heated, to tube stills, in which the heat comes into much closer contact with the oil. In 1935 the total capacity of operating pipe stills increased about 4 percent; this increase, though small, probably was related to the gain in average efficiency.The Increased use of heat exchangers and their role as fuel savers have been discussed in previous reports of this series. It is sufficient to say that refiners with insufficient exchange capacity added as much in 1935 as their budgets would permit."

Jan 1, 1937

By Kevin Connor

The Government's ban on all commercial mining operations, except for small-scale artisan exploitation of alluvial gold deposits, continued throughout 1985. Minerals produced were kaolin and lime for agricultural uses, and experimental peat harvesting for energy applications. The total value of the minerals produced during the year was estimated at $1.1 million .2 In early 1985, an agreement between the Government and Amoco International Oil Co. was ratified for a petroleum exploration concession covering 248,000 hectares of Lake Tanganyika. Onshore exploration in the Ruzizi Plain was already under way the last half of 1985. By yearend, enough seismic information was available that Amoco hoped to complete data analyses, determine onshore drilling sites, and begin drilling operations before the end of 1986. Also to begin in the latter part of 1986 were seismic studies of Lake Tanganyika. Throughout 1985, Amoco officials were negotiating with the Government of Zaire for expanding the exploration acreage into that country's portion of northern Lake Tanganyika and the Ruzizi Plain. An agreement between Amoco and Zaire could have important beneficial economic implications for both Zaire and Burundi, and onshore seismic work in Zaire logistically supported from Bujumburi could begin almost immediately.

Jan 1, 1987

By Robert F. Holub

The Bureau of Mines has evaluated four working-level radiation-measurement methods and optimized them from the inherent and statistical error standpoint. Optimization with respect to various sampling and measurement times yielded no marked improvement over the existing methods. However, when appropriate approximations are made and evaluated, these two-measurement methods can be reduced to simple formulas, eliminating a need to use nomograms. These modified methods also have improved inherent error characteristics. A new method--a combination of two existing methods--with improved inherent and statistical errors has been suggested. All the pertinent equations are given, together with the computer program, so that any two-measurement method can be readily evaluated.

Jan 1, 1980

By Allen D. Look, Stanley M. Walker, Van Fleet. Leonard A.

"INTRODUCTION The hazards to be encountered in temporarily or permanently abandoned underground mines, quarries, and open pits are numerous, and hardly a year goes by without several reported cases of fatal or serious injuries occurring to unwary people who enter these old mines. Persons visiting mining areas for the first time, tourists, and young people, especially, proceeding in the spirit of adventure common to youth or to the venturesome have suffered many such accidents during exploration trips. The possibility of salvaging salable or usable equipment prompts men and boys to go into old mines, some through ignorance of the attendant hazards, but some jeopardize their lives hopeful of gain (in some cases pitifully small), thinking the hazards are not dangerous and that they can ""get away with it.""Persons fall into unprotected holes, some seek shelter from storms under high banks, and quarries and open pits are often chosen as places for recreation, picnics, swimming, etc; all such uses of these places are likely to be hazardous and to lead to accidents, frequently fatal.These hazards are known to men in the mining profession, and the danger to the public is realized by most of them. A solution to the problem has been sought at many mining meetings, and it is recognized that complete prevention of entry into old mine workings and surface mining areas is the ideal solution, but this, unfortunately, is not always practical; better education of the public, particularly children, should help to reduce the number of such accidents and will be effective in direct proportion to the extent and vividness of such education."

Aug 1, 1948

By J. E. Pahlman

One of the goals of the Bureau of Mines is to develop metallurgical pro-cesses that conserve energy and/or that take advantage of abundant domestic energy sources. Western lignites and subbituminous coals can be used for firing pellet induration and metallization furnaces. However, the refractory linings of these furnaces must be able to withstand attack from corrosive alkali metal oxides present in the ash of many of the low-rank fossil fuels. The Bureau of Mines conducted dynamic and static slag tests on high-alumina and alumina-silica refractories to determine their resistance to lignite ash slags. The investigations showed that increased alkali content in the lignite ash caused increased corrosion and erosion of the tested refractories. The degree of corrosion decreased with increasing alumina content, with the 99-percent-alumina refractories having the highest resistance. In general, the matrix phase was attacked preferentially to the alumina grains. Also, porosity reduction and tar impregnation enhanced the corrosion and erosion resistance. The 90-to 99-percent-alumina refractories are recommended for use as furnace linings in alkali slag environments.

Jan 1, 1979

By G. M. Molinda, J. P. Ulery

Since 1970, abnormally high methane emissions have been observed in eastern sections of the Federal No. 2 Mine operating in the Pittsburgh Coalbed in northern West Virginia. The nature and volume of these emissions indicate a source other than the coalbed. An investigation was undertaken to delineate probable methane sources. Gas well information and stratigraphic correlation of corehole data indicates that a sandstone directly above the main coalbed is an additional source of methane emissions. The sandstone body appears to be an ancient stream channel, infilled with fine-grained sand and organic matter. Coalification of the organic matter produced methane as a byproduct. Additional methane presumably migrated into the sandstone unit from the subjacent coalbeds. The methane became trapped in the porous clasticunit by the surrounding impermeable strata. Mine development near this unit creates a significant pressure gradient, triggering abnormal methane emissions into the mine along naturally occurring fractures. Pre-development methane drainage of the sandstone could be accomplished by completing vertical boreholes along its trend.

Jan 1, 1984

By Thomas M. Barczak

Longwall operators are again pushing the envelope in terms of life expectancy for longwall shields. State-of-the-art shields are now expected to last more than 60,000 loading cycles, twice the life expectancy compared with those of a decade ago. A review of trends in shield design shows that shields continue to increase in both size and capacity. Some state-of-the-art shields now weigh over 30 tons and provide up to 1,200 tons of support capacity. Although life expectancy has increased and modern shields are structurally more reliable, premature failures do still occur. This paper provides an engineering and operational assessment of shield design and provides key points to observe in what causes premature shield failures. Design practices to improve structural margins of safety that will prevent premature failures from occurring are also examined. A survey of recent shield failures is provided, as well as trends in shield design and how they might impact the performance and longevity of a shield. Hydraulic failures are more common than structural failures. Although hydraulic failures occur on all aging longwall shields, they often go undetected for long periods, resulting in degraded support capacity that can lead to serious ground control problems. The fundamentals of shield hydraulics are described in order to evaluate hydraulic failures that plague all shields at some point in their service life, and practical methods to detect hydraulic failures are examined. The paper concludes with recommendations for inspecting damaged shields and safety precautions regarding their continued use.

Jan 10, 2000

Control surface stream loss by identifying and selectively sealing water loss zones in stream channels overlying underground mines. Approach Electromagnetic terrain conductivity surveys, coupled with stream gaging, are performed within a stream channel to identify saturated fracture zones associated with loss of stream water. This information is used to target locations for the injection of expandable polyurethane grout. The grout is injected two to three feet beneath the surface of the strcambed, across each loss zone, to seal the fractured strcambed and restore stream flow across the damaged area. How It Works Multiple zones of infiltration (natural and induced) normally exist in stream channels overlying mined areas, causing water handling and/or acid drainage problems in the mines as well as loss of stream flow. It is typically difficult to accurately locate these loss points. Therefore, Conventional methods of stream repair, such as using plastic membranes or clay and rock rip-rapping, are applied to long lengths of a stream channel. The two step approach developed by the Bureau of Mines First quickly and accurately locates loss zones using electromagnetic ground conductivity survey and gaging instruments. Conductivity is measured at fixed spacings (typically 25-50 ft depending on the instrument and desired observation depth), Ground conductivity increases when saturated conditions exist at depth. These apparent flow loss zones are confirmed by gaping, to eliminate possible effects due to unobservable metal debris adjacent to or buried in the stream sediment.

Jan 1, 1991

By Harold R. Newman

The performance of Ecuador's mineral industry continued to be affected not only by depressed oil prices in recent years but also by natural disasters. In March 1987, Ecuador canceled foreign debt payments for the rest of the year and appealed for international aid because of a series of earth-quakes that destroyed villages and crippled the nation's oil industry. The earthquake destroyed a key section of the country's main oil pipeline and forced a halt to production and shipment of Ecuador's most important export product. Ecuador produces 240,000 barrels of oil per day and exports 144,000 barrels daily. Oil accounts for 60% of the nation's hard currency earnings. The Government of Ecuador asked the Organization of Petroleum Exporting Countries and other oil-producing countries to assume Ecuador's oil sales commitments. Ecuador agreed to pay the countries back in an equivalent amount of oil when it was able to resume exports.

Jan 1, 1989

By Edward D. Thimons, Jay F. Colinet

NIOSH conducted a strategic planning effort to identify those areas in mining with the greatest research needs. Data analysis and stakeholder input identified the need to reduce worker exposure to respirable crystalline silica dust as a high priority area. MSHA dust sampling data were analyzed to target the mining commodities and occupations with the greatest percentage of samples containing silica above compliance levels. In response, the Pittsburgh Research Laboratory (PRL) has implemented a multi-faceted research program to improve silica dust control for these problematic commodities and occupations. A review of silica compliance trends, PRL silica research programs, and recent control technology developments are provided here.

By Berenice B. Mitchell

THE STATISTICAL tables in this chapter present, country by country, the mineral production of the world in 1949-50. The figures are on a mine basis, unless otherwise indicated, except for cement, coke, and steel, which are measured at the processing plant. The tables are essentially a retabulation, by countries, of the 53 commodity world tables appearing in the various chapters of this volume. For lack of comprehensive information, data for the following minerals are excluded: Andalusite, aplite, asphalt, boron, bromine, calcite (optical), calcium chloride (natural), carbon dioxide, clay, columbium (niobium), diatomite (kieselguhr), dumortierite, emery, garnet (abrasive), gem stones (other than diamonds), germanium, greensand, grindstones, helium, indium, iodine, kyanite, lithium, magnesium compounds (other than magnesite), meerschaum, mineral pigments, monazite, natural gas, natural gasoline, oil shale, olivine, perlite, pumice, quartz crystal, radium, sand and gravel, selenium, sillimanite, sodium salts (other than common salt), stone, strontium, sulfur (byproduct), tantalum, tellurium, thallium, topaz (industrial), tripoli) uranium, vermiculite, wollastonite, and zirconium. In addition, a few minor geographic areas for which no statistics are available, are also omitted from the tabulation; it is believed that no significant quantities of minerals are mined in any of these areas. The statistics in these tables were derived principally from questionnaires sent, in cooperation with the United States Department of State, to the governments of each country. Supplementary sources were United States consular reports, the Imperial Institute's Statistical Summary of the Mineral Industry of the British Commonwealth and Foreign Countries, other official publications of various countries, the United Nations Statistical Yearbook, the Year Book of the American Bureau of Metal Statistics, Minerais et Metaux, business magazines, and company reports. Where official data were not available, esti-

Jan 1, 1953

By J. G. Walters

In a survey of the coking properties of United States coals, the Bureau of Mines has accumulated data on more than 500 coals and blends tested by the Bureau of Mines-American Gas Association (BM-AGA) method.4/ The importance of these tests depends upon the fact that a greater number of different coals has been tested in this apparatus than in any other of similar scale, thus permitting comparison of the carbonizing properties of many coals. Evaluation of BM-AGA results with respect to industrial data supplied by member firms of the American Gas Association was one of the first objectives in developing this test apparatus and procedure. Early data showed that, de-pendent upon BM-AGA carbonizing temperature, BM-AGA and commercial results agree closely.5/ Because of limited data, statistical relationships were not established at that time.

Jan 1, 1959

By Andrew B. Cecala, Edward D. Thimons

The Bureau of Mines has successfully tested a method to simulate methane (CH~) flows from face areas through the returns of noncoal mines. This technique' involves releasing a small quantity of tracer gas at a working area and sampling for that gas downstream in the re- turn airways. By measuring the dilution of the tracer gas, the dilution of any volume of CH4 released at the face can be calculated. This information is useful in selecting locations for CH4 monitors and in deciding the necessity for permissible equipment in the returns.

Jan 1, 1984

By M. L. Whisman

Several commercial processes for reclaiming used lubricating oil were duplicated on a laboratory bench scale. Laboratory tests were selected and in some instances modified to determine the physical properties of each oil produced. In addition, the hydrocarbon composition of some samples was determined using a liquid chromatographic technique, and compared with the composition of new oil in order to determine the severity of the re-refining technique. Selected samples of reprocessed oil were reformulated with an additive package for further estimates of quality as determined by wear, corrosion, foaming, and oxidation stability tests. Additionally, several samples of commercially re-refined oil and new oil were obtained and physical properties were determined for comparative studies.

Jan 1, 1974

By Jack C. White

Studies were made to determine the character and distribution of the copper lost in copper mill tailings. Acid soluble (oxide) and acid insoluble (sulfide) copper were determined for heavy-liquid sink and float products of screen-sized fractions from 12 copper mill tailings. In most of the tailings studied, the coarse-size fractions are higher in copper grade than the respective bulk tailings, high in sulfide copper, and low in oxide copper. Oxide copper occurs predominantly in the minus 325-mesh "slimes." Microscopic examination of heavy-liquid sink products indicated that recovery of liberated copper sulfide minerals is complete in most mills, and that copper minerals not being recovered are locked with gangue particles. Additional copper could probably be recovered from most tailings by size classification, scavenger froth flotation of the coarse fraction, and regrinding of the concentrate to achieve liberation of the locked sulfides.

Jan 1, 1971

By Forrest T. Moyer

Injury experience in the mineral mining and processing industries during 1968 was slightly improved in the nonfatal-injury record but worse in the fatality record. The resulting frequency rate of all injuries was slightly better, whereas the injury-severity rate retrogressed appreciably from the figure for 1967. Overall operating activity, as measured by man-hours of worktime, was slightly higher in 1968. However, there were several major segments of the mineral industries in which activity was lower owing to reduced demand for mineral products and to several major work stoppages. These statistics comprise the injury and work experience of all personnel engaged in production, exploration, development, maintenance, repair, and force-account construction work, including supervisory and technical personnel, and working partners and owners at mineral-producing and mineral-processing establishments in the United States. Data concerning officeworkers are excluded except for the oil and gas industry for which such information is not separable. All injury rates and totals are calculated from data before rounding. The data for 1968 are preliminary except for the anthracite, coke, petroleum and natural gas, native asphalt, peat, and slag industries, which are final. The figures represent full coverage for all industries except oil and gas for which coverage is not complete, particularly with respect to small companies.

Jan 1, 1970

By J. J. Forbes

The rapid increase in the quantity of coal being mined by stripping methods is one reason for the increased interest evinced by safety and other agencies in the hazards that are inherent in this Method of mining. The coal-mining laws of some States contain general provisions governing the mining of coal by open-cut methods, but none contains a complete list of specific safety regulations or laws for-the safe operation of such mines. The cool-mining laws of one State empower the head of the coal-mining inspection organization to proscribe regulations for coal-stripping operations and gave him the authority and power to enforce the rules and regulations promulgated by him.

Jan 1, 1944