Search Documents

By Gertrude N. Greenspoon

Legislation and Government Programs.-The Occupational Safety and Health Administration (OSHA) held public hearings in early 1975 on proposed standards for exposure to inorganic arsenic. The findings obtained at the hearings will be considered to promulgate emission standards. Domestic Production.-Arsenic trioxide (As203) was produced domestically only at the Tacoma, Wash. copper smelter of ASARCO Incorporated. Production data cannot be published. Output rose 9% over that of 1974, shipments were less than half those of 1974, and stocks rose 31 %. Production of arsenic metal, begun by ASARCO in August 1974, continued in 1975.

Jan 1, 1977

By Robert E. Hershey

1. The investigation shows that the Sewanee coal bed is the most important bed in Grundy County arid is the only bed that has had any sustained production. There is no production, at the present time, from any of the other coal beds in the county. The Richland (Lower Sewanee or Coke Oven) coal bed has been prospected but has never been developed extensively. The Angel coal bed has been worked to a very small extent near Beersheba Springs, Tenn., for local consumption. The Battle Creek coal bed has been worked sporadically near Monteagle, Tenn. 2. Known measured and indicated reserves in the Sewaneee coal bed, based on a minimum thickness of 14 inches and on 1,800 short tons per acre-foot of coal in place, are estimated to be 15 millon short tons as of January 1, 1953. Of this total, 10 million tons represents coal 28 inches and more thick. Areas in the bed were omitted from the estimate where available data relative to the bed characteristics are too meager for making an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves.

Jan 1, 1955

By B. E. Blair

Accelerometers of various types, velocity gages, and a displacement meter are shown to give reliable date when measuring seismic pulses generated in rock by the detonation of explosive charges. Displacement and velocity records are differentiated and shown to compare with velocity and acceleration records. Velocity and acceleration records are integrated and shown to compare with displacement and velocity records, respectively. The experimental data are shown to satisfy the scaling laws developed by dimensional analysis. Propagation laws are developed for peak amplitudes of the first pulse of displacement, velocity, and acceleration. These propagation laws are shown to be independent of the gage used to obtain the data. As a result, the usefulness of the various gage types can be extended. For example, accelerometers, because of their high frequency and amplitude limits, can be employed near the shot to measure acceleration and/or velocity (by integration), Velocity gages, because of their higher sensitivity, can be employed at relatively larger distances from the shot to measure velocity and displacement or acceleration (by integration or differentiation).

Jan 1, 1954

By William P. Diamonds, David C. Oyler

Stimulated vertical boreholes are an effective means of removing gas from coalbeds in advance of mining. This Bureau of Mines report examines the coal mine roof damage potential of stimulation treatments. Twenty-two Government-sponsored stimulation treatments have been mined through to determine the effects on the coalbed and roof strata. Vertical fractures in the coalbed were discernible for most treatments and horizontal fractures were present for about half of the stimulations. Sand-propped vertical fractures were usually short in lateral extent. Evidence of stimulation fluid movement could generally be traced beyond the maximum extent of sand-filled fractures when fluorescent paint was added to the treatment fluids. The maximum lateral extent for a sand-filled vertical fracture was 416 ft and a paint-coated vertical fracture extended 630 ft. Horizontal fractures were generally found within bedding planes, most commonly on top of the coalbed. The maximum lateral extent for a horizontal fracture was 265 ft at a coalbed depth of 630 ft. Horizontal fractures have been found to occur as deep as 1,145 ft. Penetration of strata overlying coalbeds was observed in nearly half of the treatments intercepted. Most of these occurrences have been interpreted to be penetrations into preexisting joints. No roof falls or adverse mining conditions were encountered that could be attributed to the stimulations.

Jan 1, 1987

By W. W. Adams, V. E. Wrenn

"Production of explosives in the United States during the calendar year 1936, as represented by reports of sales by manufacturing companies, totaled 391,604,500 pounds, an increase of 27 percent over the amount produced during 1935. This quantity included 81,698,375 pounds of black blasting powder (granular and pellet), 262,047,106 pounds of high explosives other than permissibles, and 47,859,019 pounds of permissible 5/ explosives.The manufacturers' reports to the Bureau of Mines classify the sales of explosives according to five main classes of work in connection with which the explosives were used.Coal mines used 87 percent of the total amount of black blasting powder sold, bituminous-coal mines 79 percent, and anthracite mines 8 percent; coal mines also consumed 98 percent of all permissible explosives and 9 percent of the high explosives other than permissibles. The coal-mining industry consumed 16 percent more explosives in 1936 than in the preceding year, the increase at bituminous mines being 21 percent and that at anthracite mines 4 percent.Metal mines used 29 percent of the high explosives other than permissibles and less than 1 percent of the black blasting powder and permissible explosives. The total quantity of the three classes of explosives used in metal mining in 1936 was 36 percent more than the quantity so used in 1935."

Jul 1, 1937

By F. P. Haver

The Bureau of Mines developed a process to extract about 90 percent of the sulfur from molybdenite flotation concentrate by compacting the concentrate with one-quarter of its weight of aluminum powder, heating it at 800° C for 30 minutes, and then allowing the product to react with water. This thermite reduction yields an impure molybdenum alloy plus aluminum sulfide. The latter readily hydrolyzes, to yield pure hydrogen sulfide which can be converted to elemental sulfur by the Claus process. At least 95 percent of the molybdenum can be subsequently recovered as 99.95-percent-pure molybdic oxide.

Jan 1, 1968

By J. T. May

The Federal Bureau of Mines investigated the extraction of lithium from hectorite-type clay deposits found on the Nevada-Oregon border. Two clay samples were used in the investigation; one contained 0.36 pct Li and the second contained 0.64 pct Li. The purpose of this laboratory-scale research was to determine how these clays responded to different extraction techniques. Extraction techniques investigated were sulfuric acid leach, sulfuric acid bake-water leach, and roast-water leach procedures with cholorides, sulfates, carbonates, and combinations of these reagents. The processing characteristics of the clay samples showed significant variations, and no one technique was effective for both materials. Lithium extractions near 90 pct were achieved during these exploratory studies.

Jan 1, 1980

By David A. Benjamin

In 1989 and 1990, the Bureau of Mines conducted a mineral resource investigation of the 122,000-acre Trinities study area, located in the Trinity Mountains of south-central Idaho. No identified mineral resources were delineated during this study. There are 58 lode mining claims within the area. Five localities contained elevated metal concentrations which may indicate precious metal mineralization at four localities and molybdenum-precious metal mineralization at another. Four of the five localities appear to form a northwest trend through the center of the study area. Twenty-eight individual sites contain anomalous concentrations of gold, silver, bismuth, molybdenum, and beryllium.

Jan 1, 1991

By M. M. Fine

This report describes a Bureau of Mines technical feasibility study of simultaneous reduction and induration of pelletized iron ore to make a product with superior qualities as blast-furnace feed. Highly reduced, physically competent pellets can be made from magnetite and specularite concentrates that contain small additions of bentonite as binder. In batch tests, pellets were dried, surrounded with solid fuel in crucibles, and heated to the reducing temperature. Total iron content of the best products was higher than 80 percent and crushing strength of 1/2-inch metallized pellets ranged up to 600 pounds or more. Comparative tests of several commercial oxide pellets showed a wide range in crushing strengths, but most values were less than 350 pounds. Continuous tests in a rotary kiln resulted in the same degree of reduction, but the pellets had lower crushing strengths because of the limitations in the maximum operating temperature of the small kiln.

Jan 1, 1962

By Foster Fraas

The dielectric constant .has been frequently referred to as an important property in electrostatic separation whore the particles are in an air ambient. Hatfield (1) has studied the problem on the basis of fundamental theory, with the conclusion that separations in air dependent on the differences in dielectric constant, in conjunction with a nonhomogeneous field, are not feasible, because of the low dielectric strength of the air. Although Hatfield has made the statement without showing the calculation or data, calculated values substantiating this under certain conditions of the problem will be given in the following text. However, under other Conditions, these conclusions do not hold, and it is probable that the dielectric constant is indirectly influential.

Jan 1, 1948

By James H. Scott

A technique of seismic refraction data analysis has been developed in which a digital computer is used to generate a two-dimensional model representing a layered-earth depth interpretation. Travel times are picked on seismic records by the human interpreter. These times, together with shot point and geophone locations and refraction layer control information, are submitted to the computer on punched cards. A first approximation delineation of each refraction horizon is obtained by a computer adaptation of the delay-time method. The approximation is then tested and improved by the computer through the use of a ray-tracing procedure in which ray travel times computed for the model are compared against field-measured travel times. The model is subsequently adjusted in an iterative manner so as to minimize the discrepancy between computed and measured travel times. The Fortran program is listed in the appendix of the report together with instructions for preparing data cards and examples of results.

Jan 1, 1972

By B. H. Eccleston

The Bureau of Mines, in cooperation with the American Petroleum Institute, studied the effect of fuel volatility and front-end fuel composition on the amount and photochemical reactivity of automobile exhaust and fuel-system evaporative emissions. The study involved six gasolines--the base fuel, three fuels of varied volatility, and two fuels differing from the base and from each other in front-end olefin content. Data were obtained from 16 vehicles operated on a chassis dynamometer using a speed-load-time cycle that approximated a typical urban trip. Tests were made at ambient temperatures of 20°; 45°, 70°, and 95° F, using a climate-controlled dynamometer room. The amount of hydrocarbon emission and its probable photochemical effect, a potential contribution to pollution, is expressed as weight (reactivity equivalent) of a moderately reactive material, ethylene. Emissions of oxides of nitrogen, car-bon monoxide, and aldehydes were also observed. Results showed that reduction of volatility from currently typical levels serves to reduce both the amount and the reactivity equivalent of evaporative losses with a slight penalty by way of higher exhaust emissions. Alternatively, reducing the amount of light (low boiling) olefin in the fuel had no effect on the amount of hydrocarbon pollutant but did significantly reduce the reactivity equivalent of the emissions. Neither volatility change nor chemical changes to the fuel significantly affected the nonhydrocarbon emissions.

Jan 1, 1970

By R. A. Beall

A series of 45 zirconium ingots has been cast by the consumable electrode arc melting process with the object of analyzing the effects of power input from 50 to 230 kilowatts and reduced pressure furnace atmosphere to improve the quality of regular 8-inch-diameter production ingots made thereby. Electrode consumption rate, molten pool volume, melting efficiency, sidewall quality, arc stability, and yield efficiency are considered. The use of direct current and alternating current is studied. In conclusion, reduced pressure furnace operation is shown to promote electrical efficiency, ingot homogeneity, high metal yield, and are stability. INTRODUCTION Zirconium is a particularly difficult metal to melt because of its affinity for atmospheric gases and its solvent properties when molten. In addition, zirconium sponge as produced by the boll process contains minor amounts of magnesium chloride, which cause severe spattering luring melting, because of these difficulties with zirconium, and its sister metal titanium, near techniques have been developed to permit production of commercial size ingots. Among the more promising is the consumable electrode arc melting method.

Jan 1, 1955

By B. H. Eccleston

Experimental work is reported showing the effects of gasoline characteristics on auto emissions. Fuel volatility is shown to influence evaporative losses, with the higher losses associated with higher volatility. Fuel front-end olefin is shown to contribute significantly to reactivity of emissions. Large vehicle-to-vehicle differences were found. The study was conducted by the Bureau of Mines at its Bartlesville Energy Research Center in cooperation with the Coordinating Research Council Air Pollution Research Advisory Committee. The work was done using 15 1968-70 model autos and eight fuels were tested at ambients ranging from 20° to 95° F. Data on emissions from each vehicle-fuel-temperature combination are presented. Also included are calculated photochemical reactivity data and the distribution of hydrocarbon and nitrogen oxides during the test cycle.

Jan 1, 1972

By Andrew B. Cecala

The Bureau of Mines conducted laboratory and in-mine tests on the Racal airstream helmet (Model #AR21) to evaluate its protection efficiency. Laboratory tests indicated that as ambient air velocity increased, the protection offered by the helmet decreased. In tests conducted at several coal mine long-wall sections with face velocities under 400 fpm, the helmet was 84 pct effective at reducing respirable dust in the miner's breathing zone. However, at a high-velocity section, 1,200 fpm, the efficiency of the helmet was significantly reduced, confirming our laboratory results.

Jan 1, 1981

By R. E. Lindstrom

Effective separation of rare-earth mixtures is obtained using hydrogen as a retaining ion at 200° F with ethylenediaminetetraacetic acid (EDTA) eluant. Results obtained in Bureau of Mines bench-scale apparatus and large columns with hydrogen as a retaining ion closely parallel those obtained with copper as a retaining ion. The use of hydrogen as a retaining ion permits EDTA and water, collected before rare-earth breakthrough, to be recovered in a form that allows the material to be recycled without extensive processing. With the exception of yttrium and dysprosium, separation of rare-earth mixtures is improved and throughput is increased by elevated temperatures. Separation with 1,2-diaminocyclohexanetetraacetic acid (DCTA) eluant increases markedly on increasing temperature from ambient to 250° F; however, on the basis of separation efficiency, DCTA does not compare favorably with EDTA.

Jan 1, 1962

By Donald W. Mitchell

The fire hazard of neoprene, polyvinyl chloride, and rubber conveyor belts was studied at the Federal Bureau of Mines Experimental Coal Mine. The effects of intensity of ignition source, velocity of the ventilating air, and type of belt were investigated at three levels in small-scale gallery experiments. Studies were made in the mine on the effects on ignition and flame propagation of belt-entry dimensions, belt widths, and belt configuration. Methods for extinguishing belt fires were also investigated under simulated mining conditions, and during these trials coal dust and grease were placed on the belt. The research showed that conveyor belts will burn. Neoprene, polyvinyl chloride, and rubber belts, with and without carcass, ignited and propagated flame. The highest rate of flame propagation was obtained on rubber belt. The fire hazard increased with increase in intensity of ignition source and air velocity. Flame propagated only when air was forced through the test zone; propagation was not obtained when forced ventilation was not used, as would exist in a neutral entry in a mine. Automatic water sprays and high-expansion foam effectively arrested flame propagation; direct application of water and bicarbonate dusts was ineffective.

Jan 1, 1967

By Lisa Steiner, Robin Burgess-Limerick

In 2004, there were 646 underground coal mines in the USA employing 37,445 miners. These mines reported 3556 injuries to MSHA that year - 17% were associated with bolting machines (593 injuries), 8% with continuous miners (283 injuries), and 4% each with Scoop/LHD (1 51 injuries), shuttle cars (134 injuries), and personnel transport (145 injuries). The use of the frequency of reported injuries for the prioritization of risk control strategies has limitations because of the tendency to underestimate the importance of relatively rare but high-consequence events. Injury reports also underestimate the contribution of risk factors such as whole body vibration, which have a long-term cumulative contribution to an elevated risk of injury. However, taking these limitations into consideration, the results of the injury narrative analysis suggest the following hazards as the highest priority for elimination or control: • rock falling from supported roof • inadvertent or incorrect operation of bolting controls • handling continuous miner cable • collisions while driving LHD/Scoop, shuttle cars and personnel transport • rough road while driving or traveling in LHD/Scoop, SC & PT

By C. Kwong, L. H. Rorden, T. C. Moore

This report describes the feasibility test of an electromagnetic method for locating, boreholes, with or without casing, that have been drilled in conjunction with mining operations but whose location with respect to the tunnel is not precisely known. The first tests were conducted with the cooperation of the Kerr-McGee Corporation, Church Rock Mining Operations, New Mexico, in September 1977. These tests demonstrated that accuracies of better than ±15% of range and ±1° of bearing can be achieved with a simple system and setups. Subsequent tests, in January 1978, on a horizontally drilled pipe line river crossing application, by Ti tan Contractors of Sacramento, California, demonstrated that accuracies of better than one-half percent of range and a few tenths of one degree of bearing can be achieved by using refined techniques. The demonstration tests were done at ranges on the order of 100 to 200 feet but the method is capable of working at much greater distances.

Jan 5, 1978

By James A. West

COUNTRIES of the Near East, with the world's largest and insist prolific petroleum resources, produced nearly 277 percent of the world's estimated total output of crude& oil in 1964 and accounted for about 60 percent of world exports of this commodity. Although petroleum largely dominated the mineral industry of tine area, production of antimony, chromium, copper, mercury, boron, potash, and phosphate rock was of world significance. Production of crude oil in Near East countries reached a record high of 7,520,000 barrels per day in 1964, an increase of nearly 11 percent over that of 1963. Kuwait maintained its position as the leading producer, accounting for almost 28 percent of the area's output. Saudi Arabia, Iran, and Iraq followed with 22.5, 22.2, and 16.5 percent of total area output, respectively. Despite record production, the Near East, proved crude oil reserve remained in excess of 211 billion barrels, or more than two-thirds of the estimated world proved crude oil reserve.

Jan 1, 1966