Search Documents

By E. P. Youngman

This paper is one of a series of digests of foreign mining legislation and court decisions that is being prepared in advance of a general report relative to the right of American citizens to explore for minerals and to own and operate mines in various foreign countries . This interpretation of the mining laws of French Indo - China is a translation of an article published by the Department of Mines of Indo - China ; 4 and it is released subject to correction and amplification by the proper American foreign- service officers .

Mar 1, 1933

By C. H. Herty

Manufacturers and consumers of steel have come to realize during the past few years that cleanliness is of great importance in steels which must meet rigid specifications for various physical properties. Of equal importance is the consistent production of steel which is uniform in these properties. For maximum utility, steels should be uniform not only from heat to heat, but also from ingot to ingot and within each ingot. In the manufacture of killed steels such as the higher carbon forging grades, uniformity as indicated by the usual chemical analysis is easy to obtain, provided that a normal top discard is taken, as is al¬ways the case in steels poured with hot-top practice. No such uniformity, however, holds true for the nonmetallic matter, which consists for the most part of the products of deoxidation of the steel. For a large tonnage of steels which go into articles manufactured by deep-drawing processes, killed steel has never been successfully applied because with the present deoxida¬tion practice, low-carbon killed steel is almost invariably extremely dirty. To obtain the desired qualities for deep drawing, the steel is rimmed, - that is to say, deoxidized with manganese and perhaps a small amount of aluminum, - the resultant product being of high purity in the skin of the ingot, but very badly segregated at the center of the ingot, particularly in the upper-central section. This segregation necessitates a very heavy top discard, and one of the major segregates is carbon which renders the steel too hard to draw properly. If clean, low-carbon killed steel could be made successfully, much better ingot yields would be obtained than by the present rimming steel practice. Furthermore, banded structures and outside and inside seams, which are undoubtedly due in a large measure to blowholes in the ingot, are defects which are very difficult to control in rimmed steel. These defects would be minimized by clean killed steel.

Jan 1, 1931

By Jr. Herty

Manufacturers and consumers of steel have come to realize during the past few years that cleanliness is of great importance in steels which must meet rigid specifications for various physical properties. Of equal importance is the consistent production of steel which is uniform in these properties. For maximum utility, steels should be uniform not only from heat to heat, but also from ingot to ingot and within each ingot. In the manufacture of killed steels such as the higher carbon forging grades, uniformity as indicated by the usual chemical analysis is easy to obtain, provided that a normal top discard is taken, as is always the case in steels poured with hot-top practice. No such uniformity, however, holds true for the nonmetallic matter, which consists for the most part of the products of deoxidation of the steel. For a large tonnage of steels which go into articles manufactured by deep-drawing processes, killed steel has never been successfully applied because with the present deoxidation practice, low-carbon killed steel is almost invariably extremely dirty. To obtain the desired qualities for deep drawing, the steel is rimmed, - that is to say, deoxidized with manganese and perhaps a small amount of aluminum, - the resultant product being of high purity in the skin of the ingot, but very badly segregated at the center of the ingot, particularly in the upper-central section. This segregation necessitates a very heavy top discard, and one of the major segregates is carbon which renders the steel too hard to draw properly. If clean, low-carbon killed steel could be made successfully, much better ingot yields would be obtained than by the present rimming steel practice. Furthermore, banded structures and outside and inside seams, which are undoubtedly due in a large measure to blowholes in the ingot, are defects which are very difficult to control in rimmed steel.

Jan 1, 1931

By R. V. Ramani, R. Srikanth, R. Zhao

"A two-pan study was conducted to understand the factors affecting respirable dust generation potential or dustiness of coal seams. In the first part, the data from three prior comprehensive laboratory studies was analyzed to establish quantitative relationships between respirable dust generation potential and coal characteristics. This analysis indicates that respirable dust generation rate is positively correlated with Hardgrove Grindability Index (HGI), fuel ratio (fixed carbon/volatile matter), Vitrinite Reflectance (VR), and Level of Organic Metamorphism (LOM). In the second part, specially-designed single breakage experiments were conducted to determine the primary dust generation potential of 17 coal samples obtained from four continuous miner sections, three longwall sections, and the Penn State Coal Data Bank. The single breakage study indicates that primary dust generation rate is positively correlated with fixed carbon content, fuel ratio (fixed carbon/volatile matter), VR, and LOM. Since VR and LOM are strongly influenced by the process of coalification, differences in respirable dust generation rates in different coal seams may be explained by the thermal metamorphism of sedimentary organic matter during subsurface burial.Mineral particles in the range of one to five microns, if inhaled in sufficient amounts, lead to a number of lung diseases generally referred to as pneumoconiosis. A priori knowledge of the mechanisms and rates of fine particle generation during mining can aid in the development of more effective technology for controlling primary dust generation. Unfortunately, the data and knowledge currently available are not adequate for this purpose. In fact, a committee of the National Academy of Sciences on the measurement and control of dust concluded that the knowledge of the fundamental mechanisms by which coal mine dust is generated and a part of it is entrained in the mine atmosphere as respirable dust is not sufficient to clarify, let alone control, the processes involved (Anon., 1980). Under a research contract from the U.S. Bureau of Mines, Stecklein et al. (1982) have identified a number of fundamental research issues for understanding the coal fragmentation and entrainment processes.Reduction of dust generation is the best means of control since fine particles are difficult to control once they become airborne. Therefore, considerable research efforts have been directed to understand the factors influencing dust generation and entrainment, including machine design, water sprays, and ventilation. Laboratory studies have been conducted on the mechanical action of bits and machine power requirements (Evans and Pomeroy, 1966; Roepke, 1984). Since the physical characteristics of coal play an important role in the process of breakage, a number of laboratory studies have been conducted to study the relationship between coal characteristics and respirable dust generation (Baafi, 1977; Moore, 1986; Polat, 1990; Thakur, 1971). Several studies have been conducted on the relationships between coal characteristics and airborne dust concentrations (Hamilton and Knight, 1958; Khair and Xu, 1991; Organiscak and Page, 1993; Page et al., 1993). A limited number of studies have also been conducted on the relationships between coal characteristics and airborne dust concentrations in mines (Organiscak et al., 1990). Yet, no reliable method has been developed to rank coal seams according to their respirable dust generation potential. The conclusions derived from previous studies can be summarized as follows:"

Dec 1, 1996

By D. Harrington

"In order to stimulate general interest in mine safety among their employees the mining companies of Butte, Mont., instituted in 1918 a Miners' Field Day, and this field day has since been held annually about the end of July, the last one being on July 25, 1921. The mining companies of the Butte district finance this meet in proportion to the number of men employed at the time of the meet, the contributing companies with number of working force, end proportional contributions for the opening field day in 1918 being given below:COMPANY NUMBER EMPLOYED AMOUNT CONTRIBUTEDAnaconda Copper Mining Co.,12,500,$ 1,078.53Butte & Superior Mining Co.,1,800,155.32North Butte Mining Co.,,1,294,111.67East Butte Copper Co.,,850,73.36W. A. Clark Interests,,600,51.78Davis-Daly Mining Co.,,340,29.35,,,,17,384,$ 1,500.00*Note: In many mining districts it is now the custom to hold an annual Miners' Field Day. The field day, as a rule, is financed principally by the mine operators, and was instituted primarily to promote interest among miners in the ""Safety First"" movement. Usually demonstrations or contests in first aid and mine rescue are the leading feature of the day's events, which include games, races, dancing, and all the other amusements usual to a gala holiday. Thus the field (ley serves the double purpose of stimulating interest in mine safety and promoting cordial relations and community fellowship. This paper is an interesting account of the way in which the Miners' Field Day in the Butte district is organized, with data on costs, plan of organization, method of conducting, and the practical benefits derived from it. - Ed"

Oct 1, 1921

By Clinton C. Knox

During the latter part of 1943, a magnetometric survey was conducted by the Geophysical Division of the Bureau of Mines at the Mahopac magnetite mine, Putnam County, N. Y., in an endeavor to locate a segment of the ore body that reports state was cut off by a fault. The Mahopac mine was abandoned about 1895 after producing nearly 1,000,000 tons of high-grade magnetite iron ore. The results of the investigation indicate the termination of the ore body by "pinching", or a displacement of such magnitude as to place any extension at a considerable distance from the original are body. This report describes the work done on the project and presents the data obtained.

Jan 1, 1948

By R. V. Lundquist

The Bureau of Mines made a laboratory study of the amenability of anorthosite rock ( from the San Gabriel Mountains , Los Angeles County , Calif . ) to treatment by the lime soda sinter process for the extraction of alumina . The study was done under a cooperative agreement with the California Division of Mines and Geology . This report presents the results of the investigation , and it includes a review of the geology of the deposit ( 7 ) by Dr. Gordon B. Oakeshott . Interest in the recovery of alumina from submarginal aluminum silicate ores is stimulated by the fact that the domestic aluminum industry depends on imports of bauxite for its alumina requirements . Of the 8.0 million long dry tons of high - grade bauxite consumed in 1961 for producing metallurgicalgrade alumina , only 0.9 million long tons , or 11 percent , was mined in this country . During past years many organizations have carried out research programs to determine if alumina could be extracted economically from such domestic ores as clays ( 3 , 4 ) , anorthosite ( 8 ) , and other silicate sources . Successful alumina extraction is the ultimate objective of the Bureau of Mines program.

Jan 1, 1963

By Oliver Bowles

The United States has never attained importance as a producer of asbestos, the domestic output being only 1 to 3 percent of the quantity required to supply raw material for its extensive asbestos-product manu- facturing industries. Production is centered in four principal countries-- Canada, Rhodesia, Union of South Africa, and the Soviet Union. Since asbestos first became an important commercial commodity the Province of Quebec, Canada, has led in tonnage produced, but a large proportion of the output of this province is shorter, nonspinning grades. Since 1916 the Union of South Africa and Rhodesia have become increasingly important as sources of the higher-grade spinning fibers. Before the World War Russia ranked next to Canada as a producer of asbestos, but during the revolution- ary period the industry in that country was almost at a standstill. In 1926, however, activity was revived, and each year since then production and exports have increased greatly. Minor quantities of asbestos are produced in Cyprus; Australia, Finland, and several other countries. Chrysotile is the leading product in all the producing countries, but substantial quantities of both blue (crocidolite) and brown (amosite) asbestos also are produced in the Union of South Africa. Minor quantities of anthophyllite and similar amphibole varieties are mined in the United States, Italy, Bulgaria, Finland, and several other countries.

Jun 1, 1934

By Jack E. Fraley

The Bureau of Mines has successfully developed and tested a machine for spraying sealant onto coal mine roof and ribs. Dry material is transported pneumatically to a water-adding nozzle designed to provide dust-free spraying while being nonplugging and self-cleaning. The machine is self-cleaning, 35 inches in height, and capable of applying l/2-inch-thick coatings at over 1,000 ft2/hr.

Jan 1, 1978

By M. M. Tilman

The purpose of this investigation was to determine the effects of small amounts of cobalt in nickel on the tensile properties and hardness of representative types of austenitic stainless steels . Cobalt substitutions for nickel up to 2 weight - percent were made in types 302 and 309 stainless steels . Data were obtained at room temperature for tensile strength , yield strength , percentage elongation , percentage reduction in area , and hardness . In type 302 steels , tensile strength and hardness increased with increased percentages of cobalt , percentage elongation and reduction in area decreased , and yield strength showed little change . Property changes were largely due to the reduction of nickel content rather than to the addition of cobalt . In type 309 steels , only minor variations were observed for the properties investigated ; the effects of the relatively snall cobalt substitutions and nickel reductions were somewhat reduced by the higher total alloy content .

Jan 1, 1964

By W. L. Parker, W. A. Selvig

"Introduction.Powdered or pulverized coal is extensively used as a fuel, the total annual consumption*** in the United States being about 12.000,000 tons, and growing steadily. As the coal is usually pulverized so that 70 per cent or more parses through a 200-mesh sieve, it presents difficulties in sieving, because such finely divided material tends to clog the meshes. A fineness test is desirable in order to judge the efficiency of the pulverizing apparatus, and as an indication of the particle size of the coal being burned.Committee D-5 on Coal and Coke, American Society for Testing Materials, has recognized the desirability' of a standard method for determination of fineness of powdered coal. The Bureau of Mines, in co-operation with this Committee, conducted sieving tests on two standard samples of powdered coal, which are described in this paper. As a result of this work a method for making fineness tests, by band sieving, is recommended as a standard method, while a rapid method, by machine sieving, is given for routine tests.Outline of Investigation.Preliminary trial tests were made by the bureau and tentative methods were formulated for making the sieving tests both by band and by machine.Each of two samples of powdered coal was carefully mixed, and portions were sent to the twelve laboratories mentioned later. These were requested to make duplicate sieving tests on the two standard samples, by the hand-sieving and machine-sieving methods, and to follow the tentative procedure exactly as outlined. All of the laboratories made sieving tests by hand shaking and eight of them made tests by machine shaking."

Nov 1, 1923

By P. T. Brooks

This Bureau of Mines study describes a process for recovering nickel, cobalt, molybdenum, and chromium contained in complex waste superalloy grindings that, for lack of an economical domestic recovery process, are being largely marketed abroad. The process, devised by laboratory scale operations, includes scrap preparation, dissolution of metallics in hot chlorinated acidic liquor, carbon adsorption, three successive solvent extraction separations, and selective chemical precipitations. Nearly 90 percent of the nickel, cobalt, molybdenum, and chromium were separated and recovered as oxides, carbonates, and basic sulfate products.

Jan 1, 1969

By G. L. Cook

The design of a dual-inlet system for a Consolidated model 21-103C mass spectrometer is described in detail. The system permits both high-mass and low-mass samples to be run by using a single instrument. The difficulties of using a single instrument for both purposes are given and a method of minimizing these difficulties through the use of the present design is discussed, After examining the experience of five years of use, the conclusions are that the bimodal operation is practical and the low-mass analyses had nearly the same precision as before the modifications to the instrument were made. In 1951, O'Neal and Wier.5/ published the first description of the modifications made to a mass spectrometer so that the spectra of hydrocarbons with molecular weights up to 600 could be obtained. Further discussion of the equipment of O'Neal appeared in 1953.6/ Also, Brown, Melpolder, and Young7/ described a parallel inlet system designed to reduce sorption effects at room temperature.

Jan 1, 1960

By F. L. Wideman

This report describes the sinking of No. 3 shaft at the Westvaco mine. It is one of a series of publications of the Bureau of Mines on mining methods and practices in the United States. The Westvaco mine is in Sweetwater County, Wyo., approximately 23 miles northwest of the town of Green River (fig. I), There are no permanent habitations in the vicinity of the mine, and employees live in Green River or Rock Springs, Wyo., 14 miles us t of Green River. The mine plant is on a windswept, treeless plain, from which low buttes and flat-topped ridges rise. The altitude at the collar of No. 3 shaft is 6,351 feet. The climate is arid, with temperatures as low as 40° below zero in the winter. Blacks Fork, a tributary of the Green River and a perennial stream, flows near the mine.

Jan 1, 1959

By T. L. Joseph

The purpose of this article is to describe briefly the operation of a 6-ton blast furnace on a charge of bauxite, limestone, iron ore, and cast-iron turnings and to point out the bearing which smelting such a charge has upon the production of alumina cement. One object of the experiment, conducted by the Bureau of Mines in cooperation with the Aluminum Co. of America, was to determine whether tae so-called Pedersen process3 can be applied to the blast furnace. This process consists of smelting a charge of bauxite, iron ore, and. limestone, and results in to products. One is a slag containing about 50 per cent of A1203 and is intended for use in manufacturing aluminum, and the other is iron low in sulphur. Complete details of the test are published in other reports4. Blast-furnace slag is now recognized as a satisfactory and economical raw material for making Portland cement, Wm. A. Forbes5 has recently reported that in 1926 an important steel interest used well over 1 million tons of slag in producing about 24 million long, tons of cement. This is equivalent to about ½ ton of slag for each ton of cement. Alumina cement can be made direct in the blast furnace. Its physical character would have to be changed by grinding, but no change in its chemical composition would be necessary.

Jan 1, 1928

By R. C. Hickman

Manganiferous breccia formations on three properties were prospected by the Bureau of Mines from January to November 1954 in Johnson County, Tenn. The prospecting consisted of diamond drilling, trenching, shaft sinking, and crosscutting. The results of the exploratory work show the manganiferous material to be low-grade, with little vertical extension. The manuscript on this report was completed February 1955. LOCATION The prospects are in Johnson County, Tenn. (fig. 1), within a radius of 12 miles from Mountain City. The nearest railroad terminal is Damascus, Va., 14 miles from Mountain City.

Jan 1, 1956

By Frank W. Sansom

This paper is one of a series of articles dealing with milling methods and costs at metal mines in the United States, written in accordance with an outline prepared by engineers of the United States Bureau of Mines and published by the bureau. The Netta mine and concentrator is the largest of the plants of the Eagle-Picher Lead Co, It is located in Ottawa County, in the extreme northeast corner of Oklahoma, and in what is known as the Tri-State zinc and lead mining district, embracing the northeast corner of Oklahoma, the southwest corner of Missouri, and the southeast corner of Kansas. A majority of the production comes from the Oklahoma section, with Kansas second, and Missouri third.

Jan 1, 1930

By N. E. Hanna

Experience with the current version of gallery test 4, in use since 1913 to evaluate the incendivity of permissible explosives in the presence of coal dust, has shown the procedure to have inadequate discrimination. Consequently the Bureau of Mines used the up-and-down method of statistical design to investigate the incendivity of permissible explosives in the presence of coal dust and gas. A suitable device was developed to measure coal dust concentrations in the air-gas mixtures and to disperse the dust in the gallery atmosphere. A proposed testing method which uses suspended shots in a predispersed coal dust-gas-air mixture was evaluated. The new method can discriminate between different explosives with respect to their incendivity. Maximum ignitibility of the coal dust cloud by permissible explosives occurred in the vicinity of 0.3 oz/cu ft. About 10% sodium chloride in permissible explosive formulations had a very significant effect in reducing the probability of igniting coal dust. Bundled charges were more incendive than column charges.

Jan 1, 1966

By C. W. Owings

"PURPOSE OF REPORTThe safety and efficacy of permissible storage—battery gathering locomotives are becoming recognized more and more in coal mines. The great mobility of this type of haulage equipment is due to the fact that no trolley wire and bonding of rails are needed; hence wherever there is track and adequate ventilation to dilute properly any dangerous gases, the storage—battery gathering locomotive may go. As coal near the outcrop or the surface is mined out, coal farther from the outcrop or deeper in the ground must be mined, and gassiness of the coal bed often increases under these conditions. The use of electrical equip¬ment capable of giving off arcs or sparks while operating near or at the coal faces constitutes a serious explosion hazard. Often, it is uneconomical or impracticable to use animal haulage, and locomotives must be employed. The operator should consider the safest and most economical unit; permissible equipment is the answer to this problem, and storage—battery locomotives are the only permissible electric haulage units.A comparison of permissible storage—battery locomotives with cable—reel locomotives of the latest enclosed ""explosion—tested"" type has been made at the Keystone No. 1 mine of the Houston Collieries Co., at Keys one, W. Va. The information and data contained in this publication were obtained by the writer during an inspection of haulage at this mine.ACKNOWLEDGMENTSThe writer is indebted to P. C. Thomas, vice president and general manager, the Koppers Coal Co., operator of the Keystone mines, who granted permission for making the study. W. A. Wilson, general superintendent, Houston Collieries Co., arranged for the investigation and for obtaining the data. C. E. Zuspan, chief electrical inspector, and J. C. Newman, division electrical inspector, accompanied the writer underground and assisted materially in obtaining information and data upon the haulage methods and performance of the locomotives. The assistance or general mine Foreman Pierman and of mine foreman White is gratefully acknowledged."

Aug 1, 1931

By B. W. Gandrud, G. T. Bator

The recent introduction of small coal jigs in Alabama to meet the needs of truck - mine operators for cheap and economical cleaning equipment marks another step in Alabama's pioneering record in the mechanical cleaning and preparation of coal . During the past 4 or 5 years a number of these small jigs , with capacity of 5 to 10 tons per hour , have been installed at Alabama truck mines and at a few truck mines in Illinois , Tennessee , and Pennsylvania . Most of the installations have been at mines that specialize in the production of domestic , stoker coal . This report describes three models of small jigs and includes performance data obtained recently on one of the models by the Bureau of Mines, United States Department of the Interior , in cooperation with the University of Alabama, Tuscaloosa , Ala . , for the purpose of comparing it with fullsize jigs on a performance basis . With literally hundreds of truck mines now in operation throughout the country , it has been assumed in preparing this report that there is widespread interest in the availability of small - scale inexpensive preparation equipment for use at such mines in the production of steam and domestic coal and in some instances coal for manufacture of coke . Practically none of the coal from Alabama truck mines is scld to coke - oven plants ; but in some sections of the country truck mines supply a considerable amount of coking coal, and the use of small, inexpensive washers at some of them might be very advantageous during the present war emergency from the standpoint of increasing pig - iron production through improvements in coke quality .

Aug 1, 1943