Search Documents

By Richard C. Ballance

Fly ash from four sources and in certain proportions was shown to assist chemical coagulation of turbid water and settling of chemically induced floc. Fly ash reduced the time required to form the first visible floc, promoted more uniform flocs about 2 mm in diameter, and increased the mean settling rate of floc particles. Also, the addition of fly ash produced denser sludges than those obtained with alum alone. Final turbidities were independent of fly ash particle size and carbon content. Optimum proportions of fly ash additive are given.

Jan 1, 1966

By H. E. Powell

The magnetic susceptibilities of 57 minerals containing titanium, zirconium, vanadium, columbium, tantalum, chromium, molybdenum, and tungsten were determined. The source and petrographic analysis of each sample are given. Included are values for isomorphous series of minerals showing wide ranges of composition and for a few high-purity synthetic minerals.

Jan 1, 1968

By Albert W. Deurbrouck

The performance of four sand cones was evaluated by the Bureau of Mines in three preparation plants that utilized cones in various flow schemes. The cone at plant A was a simple two-product one that provided clean coal and refuse. Plant B had two cones; one cone made a primary separation and the other a secondary separation. The primary cone separated salable coal from heavy rejects. The secondary cone separated a low-ash metallurgical coal and an intermediate-ash product suitable for plant fuel or steam markets. In plant C the sand cone was equipped with a middlings draw Which continually removed an intermediate specific-gravity product below the surface of the cone. The three primary separations of raw coal effected between floats and sinks were excellent. The recovery efficiencies for the plus 1/4-inch material ranged from 99.8 to 97.6 percent, the error areas ranged from 19 to 23 square centimeters, and the probable errors in specific gravity ranged from 0.033 to 0.024. The performance data of the two secondary separations varied from excellent in plant B, where the separation was on a par with the primary separations, to somewhat inferior in plant C, where the secondary separation was effected at the middlings draw.

Jan 1, 1965

By A. T. Coumbe

During 1953-55, 31,105 miles of pipe for transporting crude petroleum and refined products was laid in the United States, a total slightly below that of the prior 3-year period, according to data compiled by the Bureau of Mines, United States Department of the Interior. The added mileage consisted of 22,571 miles of new pipe, representing about 2,163,807 tons of steel, plus 8,534 miles of secondhand pipe, equivalent to about 419,849 additional tons of steel. During the 3-year period, 13,069 miles of pipe was taken up. By January 1, 1956, the Nation had 188,540 miles of pipeline, an 11-percent gain over the 1952 total of 170,504 miles. The greater use of larger diameter pipelines indicated in recent surveys has continued, as the mileage for sizes 12 inches and over increased from 13 percent of the total mileage at the close of 1952 to 16 percent 3 years later. Crude-oil trunklines 12 inches and over in diameter gained 24 percent during 1953-55, and these larger lines represented 30 percent of the total mileage compared with 25 percent at the close of 1952. Furthermore, the mileage for crude-oil lines less than 12 inches in diameter declined 2 percent and made up only 70 percent of the 1955 total against 75 percent n the previous survey. Product Lines 8 inches and over increased 43 percent from 1952 through 1955 and composed 70 percent of the total mileage compared with 66 percent in 1952.

Jan 1, 1956

By R. B. Schluter

The objective of this Bureau of Mines investigation was to determine the effects of adding manganese compounds and ores to iron ore pellets. Manganese dioxide, carbonate, sulfate and chloride, plus six manganiferous ores from the Minnesota Cuyuna Range were tested as additives to increase the manganese content of iron ore pellets. One to 5 percent manganese, as a compound or ore, was added to five magnetite concentrates and one hematite concentrate. These concentrates were ballad, indurated (1,300° C), and tested for reducibility. Manganese sulfate and chloride were unsatisfactory additives causing cracking and degradation of the pellets during reduction. Manganese dioxide, carbonate, and the ores were satisfactory additives. The additives increased pellet compression strengths with a corresponding loss of reducibility, as compared to the pellets without manganese additions. The changes in compression strengths and reducibility were caused by the formation of Jacobite spinel and slag within the pellets. However, when the induration temperature was lowered from 1,300° to 1,200° C the reducibility and compression strengths were comparable to the pellets without manganese additions indurated at 1,300° C.

Jan 1, 1974

By Thomas Fraser, William L. Crentz

"INTRODUCTION Sulfur is a most damaging impurity in many of our American coals. From the older coal industry of Europe and Britain we can apparently learn but little about the problem of preparing and using high-sulfur coal. Although washing has long been established there for controlling ash content, sulfur is referred to rarely, as the important deposits are singularly low in sulfur.On the other hand, widely distributed coal deposits of America differ tremendously in sulfur content. Many of the more extensive beds contain too much sulfur for metallurgical use, and almost everywhere except in the Rocky Mountain and Pacific coast regions sulfur control is at least a potential problem. American coal-preparation engineers are confronted not only with great variations in the total quantity of sulfur in coal but with an intricately varying pattern of the physical and chemical forms in which the sulfur occurs. It must be conceded that the baffling problem of sulfur reduction in coal is as yet substantially unsolved, for there are but few isolated instances in which we have been able to prepare a satisfactory metallurgical fuel from coals containing as much as 2.0 percent sulfur in the raw state.It has been assumed generally that organic sulfur, being chemically combined with carbonaceous matter, is distributed throughout the coal matter and that it remains unchanged in the clean-coal part of the product during washing.Sulfur that may be washed out of the coal is that part that is combined with the iron in pyrite lenticles associated with the coal. In most of our coals it has been found that, besides the visible bands, lenses, and flakes of pyrite, extremely small and even microscopic particles of pyrite 4/ are distributed through the coal matter. Only the free, relatively coarse pyrite particles .are removed by conventional coal-washing devices, and usually most of the sulfur is still left in the product."

Dec 1, 1947

By Russell R. Trengove

The Bureau of Mines developed by core drilling the Cove Meadow copper property, also known as the Patterson property, from May 6, 1949, to August 6, 1949. It is in the Cove Meadow mining district, northwestern Humboldt County, Nev., 102 miles northwest of Winnemucca. The purpose of the work was to determine possible reserves in a mineralized shear zone in andesite that has been partly explored by several surface cuts and two shallow underground workings. Production from this zone to August 1, 1,949, was 98 tons of hand-sorted copper ore assaying 5.1 percent. The development work performed by the Bureau of Mines comprised a study of the geology, mapping the area, sampling the outcrops, and exploring by diamond drilling the shear zone adjacent to the fault. Seven holes were drilled for a total of 1,246 feet. Mineral reserves indicated by the project are confined to a length of 500 feet along the strike.

Jan 1, 1950

By Scott W. Hazen

This report presents the results of a statistical analysis of a limited amount of sample and assay data from a production panel in an open - pit phosphate mine in the Phosphoria formation in Idaho . A frequency distribution analysis is shown for the assays , sample interval lengths , and products of assay and sample interval length for the millshale , furnace - shale , and main phosphate beds . Correlation techniques were used to show the relationships between assays and sample interval lengths . Within- drill - hole and between - drill - hole correlation were also examined as a means of predicting grade trends in the ore . Simulation methods , utilizing a digital computer , were used to establish assay populations that could be used for estimating grade of ore , cutoff grades , and deposit or bed identification .

Jan 1, 1964

By M. M. Wong

A brief investigation was made to determine the feasibility of electro-refining beryllium in a KCI-LiCI-BeC12 bath. Thin, platelike crystals of beryllium metal were produced by electrolyzing technical-grade beryllium metal beads (about 94-percent purity) as the soluble anode. Operating cell conditions were: Temperatures of 450° to 600° C.; an inert atmosphere; bath compositions of (1) 38.1 mol. percent KC1, 54.8 mol. percent LiCl, and 7.1 mol. percent BeC12 and (2) 36.7 mol. percent KC1, 52.7 mol. percent LiCl, and 10.6 mol. percent BeC12; cell voltages of 0.30 to 0.80; and initial cathode current densities of 50 to 435 a./sq, ft. Current efficiencies ranging from 87 to 96 percent were obtained. Qualitative spectrographic analyses of the metal products indicated that impurities were reduced. This technique offers the possibility of producing a grade of beryllium purer than that now generally available, which may have better mechanical properties.

Jan 1, 1960

By F. J. Gallagher

Some serious fires have occurred in bituminous-coal mines because of short circuits on direct-current power systems that do not have adequate circuit-breaker protection. The writer's observation of circuit-breaker installations in numerous coal mines leads to the conclusion that many persons am not properly informed as to the true functions, limitations, and operation of circuit breakers. Faulty protection results in fire hazards that endanger lives and property. Proper circuit-breaker protection would greatly minimize or, in many instances, eliminate the hazards; moreover, many operating advantages of proper application of modern circuit breakers would be gained. The purpose of this circular is to show why fire hazards exist in many mines despite the use of circuit breakers and how, the hazards may be overcome. A method is given for determining whether additional circuit-breaker, protection is required for a specific 250/275-volt direct-current distribution system, and, if so, the approximate locations and capacities of the required supplemental breakers.

Jan 1, 1951

By W. H. Tomlinson

During the 9 years ended December 31, 1938, 188 fatalities resulted from preventable accidents in and around the coal mines of Indiana; 173 of these occurred at underground mines and 15 at stripping or open-cut operations. In addition, there may have been other unrecorded fatalities during this period. The two organizations receiving notice of accidental deaths at coal mines in this State are the Division of Mines and Mining and the Indiana Industrial Commission. Only deaths occurring at underground mines employing 10 or more men are reported to the former, as neither strip mines nor underground mines employing fewer than 10 men cone within the purview of the Indiana mining law. The mine inspectors have no Jurisdiction over this latter group of mines and do not inspect them. Fatalities at small "wagon" mines and open-cut operations are supposed to be reported to the Industrial Commission; however, in many instances deaths at small mines are not reported, the only record being a death certificate filed with the county or corporation health officer. Thus, many deaths in small mines escape attention, especially when the victim succumbs some time after the injury was received. The data presented here on fatalities in Indiana, during the past 5 years include several instances in which the only record available is a death certificate; possibly others have been overlooked. From 1934 to 1937 the fatality record was progressively worse, that of the larger underground mines in 1937 being more than twice the average for these mines for the previous 4 years and only slightly less than twice the average for all mines, including open-cut operations. The increase in deaths during 1937 was due to two explosions, with 20 fatalities in one and 2 in the other. The number of deaths in the larger underground mines was considerably less in 1938 than in the previous 4 years, but there was no improvement in the number of fatalities at the small mines, or at open-cut mines.

Jan 1, 1940

By Victor E. Kral

The Valery fluorspar deposit , also known as the Hamilton deposit , is northeast of Lovelock and 4 miles by poor dirt road east of U. S. Highway 40 . It is in the Humboldt Mining District , on the west side of the Humboldt Range , at an altitude of 6,000 to 6,500 feet . The property was examined by the Bureau of Mines on February 83/ and April 8 , 1944.4/ The last examination was made with an engineer of the Geological Survey.5/ Exploring by means of trenches , cuts , shaft sinking , coyote holes off the shaft , and a small amount of prospecting with short drill holes , was begun in January 1945 and was completed June 30 , 1945. An engineer6/ of the Geological Survey visited the property in April and again in June 1945 to complete a topographic map of the area and to note the results of exploration by the Bureau of Mines . Only minor surface exploring had been done on fluorspar occurrences previous to the Bureau's work . No mining equipment or living facilities are on the property .

Feb 1, 1947

By M. R. Geer

Samples of coal from six beds in the Roslyn-Cle Elum field of Washington were subjected to float-and-sink tests to determine their amenability to the production of high-ash boiler fuel for on-site power generation. Grindability tests and analyses of ash were made. All of the coals would require some degree of cleaning to insure a product of 25 percent ash. With two of the coals the entire size range would have to be washed. With the other four, it would suffice to clean only the coarse coal and bypass the raw fines.

Jan 1, 1965

By T. OnIin, F. F. ApIan

"A study has been made of the surface properties of coals of differing ranks, in their natural state and as modified by the addition of collectors. The evaluation of their surface properties has been done by captive bubble contact angles, water and methylene iodide sessile drop contact angles, zeta potential, point-of-zero charge (PZC) shift, and flotation. .changes in the hydrophobicity of coal is a function of both the rank of the coal and the collecting reagent.INTRODUCTIONThe chemical and physical properties of a raw coal will determine its response to a given beneficiation process. .For such processes as flotation, filtration, flocculation, dispersion, handling, dust supression and agglomeration, however, it is also necessary to consider the surface properties of the coal and mineral matter constitutents of the raw coal. In the case of a specific particle to be floated, it is also necessary to consider the properties of the coal as modified by the addition of some reagent designed to modify (usually increase) the hydrophobicity of the coal surface. General properties of the coal have been well summarized by Van Krevelen (1) and Elliott (2), while the data for the surface properties of coal are much more scattered in the literature (see, e.g.: Parekh and Aplan (3), Gutierrez-Rodrigues et al. (4), Aplan (5), Arnold and Aplan (6), Hogg and Chander (7) and Rosenbaum and Fuerstenau (8)). While a knowledge of the inherent surface properties of a sample are important, of much greater practical significance are the properties of the particle in the presence of a reagent, such as a collector, designed to enhance the hydrophobicity of the particle. This study will focus on the surface properties of coals of various ranks in the presence of a variety of collectors."

Jan 1, 1989

To precondition a stope in advance of mining and thus reduce or prevent rock bursts. Approach Drill deep holes from a mine opening in a radial pattern in the vein and load and blast to fracture, the rock prior to production mining How It Works Preconditioning of a sphalerite galena vein in a hard gangue of quartz and quartzite creates a zone of softer rock that fails by displacement rather than violently as an elastic-battle mass. However, the entire area must he analyzed carefully so that the stress transfer does not cause problems in other workings of the mine A typical drill hole pattern and explosive loading is shown in the sketch. Hole diameter is about 4 inches and a down-the-hole, type drill is used. Drilling speed in hard quartzite is about 12 inches per minute High pressure compressed air (250 psi) is used to run the drill. An overhand cut-and-fill stoping area on the 7700 level of Hecla Mining Company's Star Mine in Burke, Idaho was preconditioned above and below the

Jan 1, 1981

By F. R. McDonald

The compound ?-valerolactone has been identified in an acid fraction isolated from waste water collected from an in situ oil-shale retort. Infrared, nuclear magnetic resonance, and mass spectrometry were used by the Bureau of Mines to confirm the identification of a subfraction collected from a gas chromatograph.

Jan 1, 1974

A complete list of permissible mining equipment, rescue apparatus and gas masks tested. Prior to Jan. 1, 1929, w s published in Bureau of mines Information Circular 60972. The present list includes practically all equipment tested and. approved by the Bureau, up to and including July 1, 1929. It covers electric air compressors, coal drills, mining machines, loading machines, conveyors, mine pumps, room hoists,, mine telephones, rock-dusting machines, switches, electric cap lamps, flame safety lamps, electric hand and trip lamps, flash lamps, methane indicators and detectors, blasting units, storage battery locomotives, tandem locomotives, power trucks, concrete mixers, self-contained oxygen breathing apparatus and gas masks. The system under which these devices were tested permits the manufacturer, after his equipment has passed certain tests prescribed by the Bureau of Mines, to mark his equipment with a seal showing hat it has been "approved" by the Bureau. These tests are designs to insure that the equipment has the minimum requirements for safety in use. The only object of the Bureau in making such tests and publishing lists of permissible equipment is to safeguard the lives of workers and to help lessen the hazards of mining.

Jan 1, 1929

By P. D. Kovscek

High-pressure streams of water, known as water jets, can be used to improve the cutting efficiency of mechanical bits. During prior testing by the Bureau of Mines, the cutting performance of a longwall shearer, equipped for water-jet-assisted cutting, was evaluated. The performance of the shearer did not improve while using water jet assist because the pressure of the water delivered to the rock surface was inadequate. The study, described in this report, resulted in a determination of the major cause of water pressure loss on the shearer, and an evaluation of the techniques for increasing the water pressure at the rock surface. The results show that the major pressure loss, which occurred between the nozzle and rock surface, is directly affected by the amount of fluid turbulence that develops just upstream from the nozzle. Preventing a sudden change in the direction of the flow channel can increase the stagnation pressure as much as 400 pct. Smoothing the surface of the flow channel in the shearer bit block would increase the stagnation pressure delivered to the rock surface by 35 pet.

Jan 1, 1989

By B. J. Dalton

The Helium Research Center, Helium Activity, Bureau of Mines, is presently engaged in a critical examination of all of the PVT data on helium that appear in the literature. The long-range objective is the development of a single equation of state for helium that will allow all of the thermodynamic properties to be calculated and will reproduce all of the data within the accuracy with which the data are known. A preliminary objective is to obtain the best values of the second virial coefficients and to develop an equation that will reproduce the best values as a function of temperature. The method of treatment consists in expressing the PV product of a gas, for a given isotherm, in terms of a power series in either the pressure or the density and evaluating the constants by least squares solution. Associated with these functions whose coefficients have been evaluated by least squares, the following errors, or deviations, are of interest; the standard error of a single measurement; the standard error in each coefficient; and the standard error of the resulting function.

Jan 1, 1964

By B. J. Dalton

The Helium Research Center, Helium Activity, Bureau of Mines, is presently engaged in a critical examination of all of the PVT data on helium that appear in the literature. The long-range objective is the development of a single equation of state for helium that will allow all of the thermodynamic properties to be calculated and will reproduce all of the data within the accuracy with which the data arc known. A preliminary objective is to obtain the best val¬ues of the second virial coefficients and to develop an equation that will reproduce the best values as a function of temperature. The method of treatment consists in expressing the PV product of a gas, for a given isotherm, in terms of a power series in either the pressure or the density and evaluating the constants by least squares solution. Associated with these functions whose coefficients have been evaluated by least squares, the following errors, or deviations, are of interest; the standard error of a single measurement; the standard error in each coefficient; and the standard error of the resulting function.

Jan 1, 1964