Search Documents

By Joseph A. Perry

One goal of the Bureau of Mines is to develop technology tp insure a dependable supply of minerals to the United States. To support this goal, the Bureau's Albany Research Center has modified a commercial atomic absorption spectrophotometer to rapidly determine trace levels of mercury by cold-vapor atomic absorption spectrophotometry. Such diverse materials as ores, mill products, stream water, sediments, and flue dust have been analyzed. A very high dynamic range of 0.2 ng/ml to 1 µg/ml of mercury in solutions is routinely analyzed by this instrument.

Jan 1, 1981

By S. R. B. Cooke, F. D. DeVaney

"INTRODUCTION The potash mineral receiving the most attention in the newly discovered. New Mexico-Texas potash district near Carlsbad, N. M. is sylvite (potassium chloride). Sylvite contains more potassium than any other mineral. Merchantable high-grade deposits have been found, and those of lower grade may be enriched to a high degree of purity by refining methods. Deposits containing sylvite were the first to be developed and axe the only ones being mined.However, many other minerals that contain potash occur in the salt beds of the Carlsbad District. Of these the more important are polyhalite, carnallite, langbeinite, leonite, and kainite. The nature of the deposits and their mineralogy have been described in detail by members of the United States Geological Survey. 4/Langbeinite, although not so abundant in these deposits as carnallite and has particular interest because the potash is in the form of the sulphate and as such commands a premium in terms of K20 unit. This is explained by Fox and Turrentine 5/, who state:"

Feb 1, 1936

By David A. Monaghan, Kenneth R. Maser, Adi R. Gurdar, D. Randolph Berry

2. Preliminary Study - Initial Probing 2. 1 Introduction Initial probing of the mine passage is required prior to the emplacement of the sealant material or deployment of the seal checker system. Factors which are of interest in sealing and checking include a. size and condition of the mine passage b. location of the borehole with respect to the ribs c. the presence of water flows d. the proximity to an intersection The importance of each of these factors depends strongly on the sealant material. Because the sealant material had not been selected at the time of the initial probing study, a broad survey of probing techniques was conducted. The capabilities and limitations of each technique as they applied to probing through the borehole were identified. To facilitate this comparitive evaluation, Table I was prepared which lists all passage conditions which might affect the emplacement of sealant material in the passage. The most satisfactory techniques for observing each condition of interest are listed together with the effects of the observation on the sealing operation. Table II summarizes the environmental conditions likely to be encountered in the passage being probed and the physical

Jan 1, 1973

By J. A. Eisele

The Bureau of Hines conducted a bench-scale investigation of a concentrated H2S04 reaction for recovering and separating rare-earth elements, barium, and strontium from a bastnasite ore and byproduct. Barium and strontium were dissolved in the concentrated acid and precipitated as a mixed product by water dilution. Separation of strontium from barium was effected by reaction with Na2C03 solution, followed by a dilute acid leach of the SrC03 formed. After removing the barium and strontium from bastnäsite are, the rare-earth elements were roasted to water-soluble sulfates. The rare-earth sulfate solution was subsequently processed by solvent extraction to produce rare-earth oxides low in lead and magnesium.

Jan 1, 1974

By David C. Peters, Robert S. Crosson

A method of error analysis has been applied to the location technique of non-linear least squares iterative inversion in order to evaluate the resolving power of several seismic array configurations with various assumed earth models and errors and inaccuracies in arrival times. The results obtained demonstrate that lateral accuracies of location are improved significantly when the depth of the miner is known. Lateral location to within 100 feet appears achievable in many instances. If it is possible to refine earth models significantly beyond what has normally been assumed in this work by the use of on-site data, or if the mine is shallow (300 feet or less), accuracies of-about 30 feet or so may be attainable. Inaccuracies in earth models of about 5% are found to contribute much more heavily to these location inaccuracies than errors of a few milliseconds in picking arrival times; however, arrival time errors of 15-20 ms or above will dominate these model inaccuracies. The expected accuracy of location is found to fall off very rapidly as the miner moves outside the array. The strength of this effect depends markedly upon the geometry of the array configuration and can be reduced by careful design. Also, as the size of the array is increased, expected location errors within the array are not altered much, but continue to match the error associated with the smaller array over a larger area (assuming that all stations can still pick up the miner's signals). Better location accuracy, especially with respect to depth control is achievable in an earth where the velocity is depth-dependent (increasing with depth) than in one which is homogeneous. This is an advantage since the

Jan 1, 1974

By J. W. Horne, W. L. Finley, A. D. Bauer, D. W. Gould

"The Bureau of Mines and the State of Colorado are cooperating in an investigation of the oil shales of Colorado. in this report the yields and the results of analyses of the oil and, gas produced from a number of oil-shale samples from the principal deposits of Colorado and other oil-shale States, are compared with samples from Scotland and Australia, where the oil-shale industry has had its greatest commercial development, and also with a sample from Brazil *here extensive oil-shale deposits are found shale samples were not selected as being representative of the different deposits, but they illustrate the wide variation in the nature of the organic matter of different oil shales.A further study is being made of the chemical composition of the shale, distribution of nitrogen and sulphur. in the products, temperatures at which organic matter decomposes, and the results will be presented in subsequent Papers, With complete data available on the chemical composition of the shales, it may be possible to explain some of the differences in the nature of the products from the various shales,Most of the work described herein was done under the supervision of M. J. Gavin. L. C. Karrick, formerly of .the Boulder laboratory, assisted in the work and gave many valuable suggestions."

May 1, 1924

By John H. Soule

"Although known since 1902, the Capitan iron deposits have not been mined, mainly because of the low grade of the ore. Only a small amount of exploratory work has been done since the discovery. C. H. Johnson, district engineer of the Bureau of Mines in New Mexico in 1942-45, visited the property; as a result, preliminary sampling of the property was done in 1943.3/ Owing to the results of this preliminary work, an extensive development program by wagon drilling was planned and executed early in 1944.4/ Equipment available at that time was limited in the depths that could be reached; and, as geologic studies indicated the possibility that other limestone beds below the surface might have been replaced by iron minerals, a supplementary development program by churn drilling to reach greater depths was prosecuted in late 1947 and early 1948, with the author as project engineer.The following sections note the location and accessibility of the deposits and mention the physical features, climate, labor and living conditions. Property and ownership are outlined, the history and production of the property stated briefly, and the ore deposits are described. The work done by the Bureau of Mines is explained and supported with maps, sections, and assay logs.From March 1, 1944, to June 1, 1944, 179 wagon-drill holes totaling 3,490 feet and 4 test pits totaling 75 feet were completed, and from November 1947 to February 1948 seven churn-drill holes totaling 2,488 feet were drilled and sampled. Metallurgical tests are summarized and referenced.With respect to this report, special acknowledgment is due to J. H. Hedges, chief, Tuscon, Ariz., Branch, Mining Division, and to W. R. Storms, engineer in-charge of the Silver City, N. Mex., field office. Acknowledgment also is due to J. Bruce Clemmer, chief, Tuscon Branch, Metallurgical Division, for analyses done in the last phase of this project, and to Dr. Vincent Kelley of the Federal Geological Survey for his cooperation during this work.The Capitan iron deposits are in secs. 10, 11, 13, 14, and 15, T. 8 S., R. 14 E., central Lincoln County, N. Mex., as shown on figures 1 and 2. The only known large deposit upon which the Bureau did development work lies around the common corner of secs. 10, 11, 14, and 15, as shown in figures 2 and 3, and just southwest of and in the foothills of the Capitan Mountains. This range of mountains trends east and west. The elevation of the highest peak is 10,205 feet.The deposits are reached by traveling on State Highway 48 from Capitan north for 4 miles, to a point just inside the Lincoln National Forest fence and thence due east over a poor dirt road for 1.2 miles. Just over a small wooden bridge, the left-fork is taken, and the poor road is followed to the deposits, a further distance of 1.1 miles (see fig. 1). This road follows the fence to and through the Davis ranch. All the roads from Capitan to the deposits are dirt roads but are impassable only for short periods during and after heavy rain or snow."

Aug 1, 1949

By J. E. Tiffany

"The new permissible blasting device, Cardox, utilizes as a blasting agent liquid carbon dioxide which is discharged.as a gas from a steel container or shell. The loaded shell is placed in a borehole, stemmed, and tamped in a manner similar to that employed with explosives, and is fired by electricity.The Bureau of Mines' approval for use of the device in coal mines was granted as Approval No. 1 under date of October 3, 1928; as the result of tests made under the conditions and requirements of Schedule 20. There have been three subsequent extensions whereby minor modifications in the original design were granted.The permissibility of the device is subject to the following conditions; (1) It shall be in all respects similar to the sample submitted for tests; (2) certain thicknesses of disc and. weights of heater ingredient and of carbon dioxide, all of which are set forth in Table 2 under the provisions governing permissibility, must be used: (3) the rear cap must always be in place after the shell has been charged, to prevent accidental firing; and (4) firing must be done by means of a permissible-type blasting unit.The permissibility of Cardox was established by gallery tests similar to those used in testing explosives for permissibility. In these tests the shell was discharged into gallery 1 without causing any ignition of gas and air or of gas, dust, and air mixtures there. The conditions of charging the shell, such as weight of the ingredients of the heater element, the carbon dioxide charge, and thicknesses of the disc, were varied according to the conditions under which it would be likely to be used in blasting. The tests made in gallery 1 are here described in detail, as are also the tests which have been made for determining the propulsive strength of the device and the quantities of poisonous gases given off when a shell is discharged."

Mar 1, 1929

By J. B. Janus

In connection with the purchase of coal under specifications for Government use, the Bureau of Mines in this report has compiled data on 81 mines located in 15 States. This annual report lists analytical data on the composition and quality of tipple and delivered samples of coal collected during fiscal year 1973. Tipple samples were collected by Bureau of Mines engineers at tipples as coal was being loaded into railroad cars or trucks. Ultimate analyses are given for most of the coalbeds listed. The deliveries were sampled at destination in accordance with instructions issued by the Bureau of Mines. All samples were analyzed in the Bureau laboratory at Pittsburgh.

Jan 1, 1973

By T. W. Johnson

The Bureau of Mines, in cooperation with the Natural Gas Department of the American Gas Association, has in progress a study or the flow of natural gas through high-pressure transmission lines. A major problem of this study is to compare the deliveries calculated from the gas pipe-line flow formulas commonly used, with the metered deliveries from pipe lines in operation. In order to obtain such comparisons a series of tests has bean made on 25 operating pipe lines in Kansas, Oklahoma, Louisiana, Arkansas, Texas, and California ACKNOWLEDGEMENTS Study of the flow of natural gas through high-pressure transmission lines was made under the general supervision of H. H. Hill, former chief petroleum engineer of the Bureau of. Mines, H. C. Fowler, acting chief petroleum engineer of the Bureau of Mines, N. A. C. Smith, superintendent of the Bureau of Mines Petroleum Experiment Station at Bartlesville, Okla., and T. Brandenthaler, chief of the oil and gas action of the Bartlesville station.

Jan 1, 1929

By J. D. Davis

"Introduction.Sixty years ago, M. Berthelot found that ethylene could be selectively absorbed from gaseous mixtures by concentrated sulphuric acid, and that the compound formed by the chemical union of the gas and acid was readily decomposed by heating with water, yielding ethyl alcohol. Only within the last few years has there been any attempt to make use of this discovery technically.Bury*, working in England at the Skinningrove Iron Works and on a commercial scale, developed a technical method for converting, the ethylene of coke-oven as into alcohol. With a gas containing less than 3 per cent of ethylene, he obtained a yield of 1.6 gallons of alcohol per ton of coal carbonized.De Loisy** perfected a technical method for treatment of coke-oven as for alcohol. Evidently this work was carried out on a semi-commercial scale. His method is based on the use of catalytic agents for hastening the absorption of ethylene by sulphuric acid. He uses part of the spent acid for drying the gases and pact for the manufacture of ammonium sulphate. Excess acid is reconcentrated by waste heat. Others have worked on the problem, but so far there has been no large recovery of ethylene from coke-oven gases. The chief difficulty seems to lie in the low efficiency (about 50% of methods and tae relatively low concentrations of ethylene in the gases treated. Gas from Trent amalgam*** contains much larger percantages of ethylene than does coke-oven gas, as Will presently be shown, and if it should ever prove practIcal to treat industrial ;as for alcohol, this gas would offer attractive possibilities,* Bury, Ernest, Ethylene as Alcohol from Coke-Oven Gas: Gas Journal' Vol. 148, D. 30, 1919, pp. 718.** DC Loisy, M.E., Sur un procede' industrial de fabrication syntlotique de l'alcool et de l'ether a partir des gaz de distillation de la houil Comp Rend, vol. 170, Jan. 1920, p. 50-3.*** A paste consisting of approximately part oil such as that obtained as for cleaning coal. See Perrott. in cleaning coal, Chem 3 parts finely pulvarized coal and 1 final product in the Trent, process StJ, and Kinney, S.P. The use of oil Vol. 35 August 3, 1921, p, 183.. & Met."

Nov 1, 1922

By R. V. Ramani, J. M. Mutmansky, J. Qin, J. Organiscak, R. Bhaskar

"The results of a two—year research study into the relationship between quartz dust levels in host material and in respirable dust in continuous mining sections are presented in this paper. The experimental design and sampling procedures for underground data collection are outlined. The sample analysis procedures for quartz determination, the ¬analysis results and conclusions of the study are discussed.The results of the study indicate that the quartz contents of the airborne dusts are generally higher than those in the host material and bulk samples; and the quartz content increases with decreasing size of the airborne dust. The source for quartz appears to be the roof and the floor materials rather than the coal seam itself. It also appears that the material containing quartz may be breaking into a different size distribution than coal.INTRODUCTION Without doubt, the potential for permanent and severe health damage exists due to respirable dust in the work environment. The attention directed at the reduction of respirable airborne dust to levels below those specified in the law and the achievements to date in meeting these standards are but a reflection of the recognition by many parties government, industry, and labor - of this potential and the need to reduce it.The ambient dust standard in underground U.S. coal mines (2 mg/s3) has a qualifier (Code of Federal Regulations, Title 30, Part 71.101) to determine an applicable dust standard when a respirable dust sample contains more than 5% quartz. This standard is frequently referred to as the ""reduced standard."" The reasoning behind the reduced standard is the relative toxicity of the quartz dust compared to that of pure coal dust. As the quartz levels in samples increase, the applicable standards become more stringent and maintaining the workings in compliance becomes increasingly difficult.The number of underground work locations operating under the reduced standards has shown a dramatic increase since 1980 (Figure 1). For comparison purposes, there were no mining entities operating on reduced standards prior to 1977. The emergence of this problem, which affects the health and safety standards on one hand and creates severe compliance problems on the other, has been rapid."

Jan 1, 1990

By Jeffery M. Listak, Ernest A. Curth

"It took only 9 years from the first appearance of roof shields on the U.S. longwall mining scene to the present predominance of shield faces. An apparent consequence is the welcome downward trend in accidents related to failures in longwall ground control. The report addresses load prediction, the effects of shield geometry on support loads, factors contributing to ground control, and related techniques. The Bureau of Mines took an active part in the evolution of longwall mining, including developing one of the first shield faces in 1975, the first lemniscatetype shields in 1976, the Mine Roof Simulator completed in 1980, the first shields in steeply pitching coalbeds in 1981, and the first multilift working of a thick coalbed in 1982. The information offered in this state-of-the-art report will assist in establishing criteria for roof support selection. INTRODUCTIONIn terms of roof support technology, the introduction of shields in the seventies and eighties was a major step forward. Table 1 indicates the predominance of shield faces on the U.S. longwall mining scene and its apparent consequence, a welcome downward trend of ground-control related accidents.The rapid progress of longwall technology began in 1975 and is highlighted by a development leading from the caliper shield to the modern lemniscate type. Shields have been gaining preference over chocks since their advent to longwall mining in 1975. Safety and productivity factors favoring shields over chocks are--1. A sheltered working space requiring minimum cleanup work.2. Structural stability that allows advancing without delay even with brushing roof contact and, by controlling all lateral loads, removing the requirement for cumbersome leg restraint and restoration devices.3. Wide hydraulic range of mining height.The development of roof shields in the Federal Republic of Germany preceded and paralleled their rapid adoption by U.S. miners. In 1983, 87 pct of the total production in Germany came from shield faces (1).2 In Great Britain, the National Coal Board introduced the first shield support system in 1977 to initiate Advanced Mining Technology (ATM) and Heavy Duty Mechanization (HDM) programs; as of mid-1982, 44 shield faces were operating, or 7.5 pct of a total of 581 faces CJ_)."

Jan 1, 1985

Although the technology involved in removing material from below the earth's surface has a long history, communication systems in underground workings are relatively new to the industry. Communication equipment did not begin appearing in underground mines until the early 1900's. Figure 1-1 shows a miner using a Western Electric standard telephone set for underground mines in 1913. These early phones were essentially the same as those used aboveground, except that they were enclosed in cast-iron boxes as protection against moisture, acid fumes, and gases. In the 1950's, the Chesapeake and Potomac Telephone Co. of West Virginia introduced a telephone set for use in explosive atmospheres that was designed around the philosophy of explosion containment. To contain an explosion within the telephone set required a 39-pound casing, which greatly limited portability. [ ] Both of these telephone sets required "pipe" or conduit, not a very practical item for a 100-squaremile coal mine. A common thread prevalent in the first 40 years of design and development is that the primary effort was placed on the telephone set. In the early 19701s, as work began on the design of modern communication systems for use in underground mine environments, the following requirements were established: 1. Must meet intrinsic safety standards .--This applies not only to coal mines, but to other explosive environments. 2. Must be compatible with the environment.--The system must with- stand dust, moisture, and corrosive conditions. 3. Must be rugged in structure.-- The system must withstand maintenance by 10-inch pliers and 4-pound hammers, as well as impact from a falling piece of roof. 4. Must be size-flexible.--Whatever is built must be sized for the small operator as well as the large companies. 5. Must be a total system in design.--The system must be intrinsically safe, including cable, power supply, and station set. 6. Must work with present telephone system.--The system should be compatible with aboveground communications already in place; it should not be the single cause of change in aboveground communications. 7. Value-added pricing.--The system should be reasonably priced so that savings created by its introduction will more than offset the installation cost.

Jan 1, 1984

By Richard J. Mainiero

Traditional techniques for the experimental determination of toxic fumes produced by the detonation of high explosives are not applicable to blasting agents. To detonate properly, blasting agents require confinement, a significant booster, charge diameters of 3 inches (7.5 cm) or greater, and charge lengths greater than two-times the charge diameter. Without these conditions, blasting agents will not detonate at full order, leading to a misrepresentation of the gaseous products. A facility for detonating large, confined charges in a controlled volume has been constructed at the Pittsburgh Research Center’s Experimental Mine. The facility consists of a portion of mine entry (once used for full-scale mine explosion research and demonstrations) enclosed between two explosion proof bulkheads. Total volume of the chamber is 9,666 ft (274 m). The chamber is equipped with an air circulating system and is3 3vented using the mine's airflow. Up to 10-pound (4.5-kg) charges can be detonated in the chamber using a variety of confinements. For a typical test, the blasting agent is confined in a 4-inch (10-cm) schedule 80 steel pipe and initiated by a 3-inch (7.5-cm) diameter, 1-inch (2.5-cm) thick Pentolite booster. This combination of confinement and initiation yields a detonation velocity of about 4,000 m/sec for ANFO. This velocity is in line with that measured for blasting in the field. Twenty four 2-inch thick steel plates are suspended around the pipe bomb to stop shrapnel that would otherwise seriously damage the chamber. Following detonation of an explosive in the chamber, a circulating fan is run for about 10 minutes to uniformly mix the chamber atmosphere. Fumes samples are taken out of the chamber through 1/4-inch (0.6-cm) Teflon or polyethylene2tubes for analysis. The fumes are analyzed using bubblers or Vacutainers to collect samples for analysis by the analytical chemistry lab. The technique described here has been employed to determine the fumes produced by the detonation of a variety of ANFO formulations and commercial explosives. This technique may be developed as a standard test to measure fumes produced by blasting agents or may be used to provide data with which to develop a computer model that will reliably predict the expected fumes production based on chemical composition.

By 1928-05-01

"The carnotite ores of Colorado and Utah were the chief source of radium for many years. In the fall of 1922; news of the very rich deposits of radium ore discovered in the Belgian Congo caused almost complete cessation of domestic production. The Congo ore contains pitchblend and a number of alteration products, including the new minerals bequerelite, curite, kasolite, stasite, and dewindite. Reports indicate that a considerable amount of ore containing over 50 per cent U308 has been produced. It seemed certain that radium could be extracted from the Congo ore at a much lower cost than from the relatively low-grade carnotite; and in order to preserve their elaborate marketing organizations, the larger American producers made agreements with the Belgium syndicate to market the foreign product in this country. The price of radium has been held at $70 per milligram. Extraction of radium from carnotite by the usual methods does not appear to be profitable at that price. With one exception, all American firms ceased production after their accumulated stocks of ore had been treated. The United States Radium Co., which continued to treat carnotite for several years, has recently shut down its plant.Although there is probably a large profit derivable from the treatment of Congo ore, it is not likely that the Belgium Syndicate will meet sufficient competition to cause any reduction in the present quotations. It is not known how long the high-grade ore will last, but when exhausted the price of radium may be expected to advance. According to K. L. Kithil3 it is the opinion of interested parties that, so far as can be forseen, radium will in future years never again be obtained at the present low price.Carnotite contains the valuable element, vanadium, which is not present in the Congo ore. The recovery of-vanadium is an important factor in the cost of extracting radium from carnotite, and under favorable conditions carnotite can be profitably treated for the vanadium alone. Vanadifecous sandstones are found ranging all the way from roscoelite (vanadium mica), containing little or no uranium; to a high-uranium and low-vanadium carnotite. Ores containing 2 per cent or more U308 are classed as radium ore and are sold on the basis of the uranium content, which is proportional to the radium content. Only in exceptional cases have ores been evaluated on the basis of both the radium and vanadium contents, although the presence of vanadium has undoubtedly influenced the price of radium ore."

May 1, 1928

By F. W. Brown, F. C. Gibson

"INTRODUCTION There is urgent need for a satisfactory permissible multiple-shot blasting unit capable of firing 10 detonators in series and safe for use in underground mining where a. gas-ignition hazard may exist.. As there is at present no entirely satisfactory permissible unit of either the battery or generator type, tile described capacitor-battery type has been developed. Consideration of the Bureau of Nines approval schedule pertaining to the generator and magne to-type units and of the electrical characteristics of the unit described in this report indicate that this unit should meet Bureau of Mines permissible requirements.This report gives a detailed description of the design and operation and results of tests to determine safety of operation in gassy atmospheres.DESIGN AND OPERATION OF UNITOperation of the vibrator-type multiple-shot blasting unit is based upon utilization of the discharge energy from a capacitor charged to a given. voltage and having capacitance adequate to store enough energy to initiate 10 detonators in series. The primary source of energy is a 4-volt cap lamp battery such as is carried for illumination on the person of underground workers in nearly all mines. As this battery is already available and is recharged daily it is considered to be a reliable and convenient source of energy for a blasting unit. Figure 1 is a schematic diagram of the circuit for an improved unit, and figures 2 and 3 are views of the experimental unit. The battery potential is applied through a radio-type synchronous vibrator (8) to an 8-volt center-tapped primary of a small transformer (9) having a high-voltage center-tapped secondary. The vibrator introduces an alternating low-voltage potential into the primary and mechanically produces full-wave, rectified, pulsating, direct current from the secondary. A buffing condenser (11) across the secondary gives the proper wave form for long vibrator life: a resistor (12) its in series with this condenser across the total secondary to protect the transformer in case of• failure .of this capacitor. A voltage divider (10) with an adjustable slider permits accurate adjustment of the potential applied to the high-capacity firing condenser (5)."

Oct 1, 1947

By A. M. Dale, J. Standeven, B. Evanoff

Tool manufacturers continue to incorporate new designs to the internal mechanism of tools in order to decrease the vibration that is delivered to the hand during operation. Modification of some tools to minimize tool vibration is not easily resolved through internal tool design. For this reason, vibration damping materials applied between the tool and the hand are a simple alternative. The damping materials may be applied to the area of the tool directly contacted by the operator or in a glove containing a vibration absorbing pad. These interventions are developed specifically to damp vibration but are not necessarily produced and tested under the same work conditions that a company may expose their workers. Therefore, it is important to test the value of the proposed interventions for the specific applications. This study evaluates the effectiveness of anti-vibration interventions currently in use at a local manufacturing company. Methods The design of this study evaluates the vibration energy produced at the tool handle and from the back of the operator’s hand. Each operator performed a series of fastener installations in metal using several interventions and one series with no intervention as a control. Four of the interventions were gloves containing anti-vibration material and the fifth intervention was an anti-vibration material wrapped around the tool handle. The protocol for wrapping the tool handle was developed and is part of the equipment procedure at this manufacturing company. Test conditions mimicked production work conditions including similar materials, fasteners and technique for installation. Vibration values were collected using 3 tri-axial accelerometers with one firmly glued to the tool handle close the hand grip as recommended by ISO 5349. A second accelerometer was placed on the top of the pistol shaped tool. The third accelerometer was attached to the back of the hand close to the third knuckle using double sided tape. Results Preliminary results for 3 volunteers show a difference between the vibration values of the control condition (mean hand vibration on bare hand = 1.77 Gs) compared to all of the interventions (p=.0001 using Mixed Procedure, Tests of Fixed Effects). The graph below shows individual trials for each subject for each condition. Glove 3 with the air bladder insert shows large variability between subjects (Range = 0.84-3.33 Gs). The other interventions show much less variability both within subjects and between subjects indicating consistent response with use of the intervention.

Jan 6, 2006

By R. K. Conrad

The Bureau of Mines conducted corrosion research to determine suitable construction materials for geothermal resource recovery plants. Weight loss, pitting and crevice corrosion, U-bend stress corrosion, and electrochemical polarization measurements were made on selected metals in brine and steam process environments produced from high-enthalpy hypersaline brine from geothermal well Magmamax No. 1 at the Salton Sea Known Geothermal Resources Area, Imperial Valley, Calif. Cadmium (and by extension cadmium coatings) and a 6061-T6 aluminum alloy were unsatisfactory because of high general corrosion rates and, in the case of aluminum, severe pitting Molybdenum and niobium (columbium) were resistant to general corrosion, pitting, and crevice corrosion, Copper alloys corroded at rates that may preclude their use in wellhead brine, The presence of iron accelerated the corrosion of the copper alloys Titanium alloys were resistant to general corrosion and stress corrosion cracking in all of the environments. They exhibited crevice corrosion in some of the brine and steam environments and Ti6A14V pitted in the brine environments. They exhibited passive behavior over a broad range of potentials. Exposure tests were conducted on a high-temperature polyphenylene sulfide thermoplastic (Ryton) in the same environments. A 40-pct-graphite fiber-reinforced Ryton composite deteriorated readily in wellhead brine and failed in all of the brine and steam process environments; Ryton coatings on 316L stainless steel were adherent and performed well.

Jan 1, 1983

By K. J. Liles

To encourage the development and conservation of the Nation's ceramic raw materials, the Bureau of Mines, U.S. Department of the Interior, under an agreement with the Georgia Department of Natural Resources, evaluated samples from a clay resource located in Clay County, Ga., for use as a raw material for lightweight aggregate. The physical properties of clay samples, taken from 5-foot increments of drill cores from 11 holes, were determined. Raw materials were plasticized and extruded to produce 1/2-inch by 1-inch pieces and fired in a rotary kiln to produce lightweight aggregate samples. The resulting expanded material had excellent loose pour weights ranging from 30 to 37 lb/cu ft. The expanded test materials were crushed, sized, and used as aggregate to form concrete cylinders. The unit weight and compressive strength of the cylinders averaged 106 lb/cu ft and 3,350 lb/sq in, respectively; these values meet American Society for Testing and Materials specifications for structural concrete. The clay from the drill cores was also used to make test bars that were evaluated for building brick.

Jan 1, 1980