Search Documents

By L. A. Stewart

"SUMMARYThis paper describes most of the chrysotile-asbestos deposits of Arizona. Mining methods are discussed briefly and asbestos-mill flowsheets are incorporated. Arizona asbestos mines are the only sources on the American continents of naturally iron-free chrysotile spinning fiber that is so urgently needed for electric-cable coverings, especially on warships.Asbestos was first recorded and recognized in Arizona in 1872, and a minor amount was produced from a deposit in the Grand Canyon in 1900. The discovery of a deposit in the Salt River district in 1912 initiated intensive prospecting, and deposits soon were developed. The total Arizona production of all grades of asbestos through 1953 is estimated at 30,000 to 35,000 tons.The deposits of the Central Arizona region, which are discussed in this paper, are scattered over nearly 2,000 square miles. The annual output is relatively small, because the asbestos occurs in thin, discontinuous veins and only in areas where intrusions of diabase are adjacent to or crosscut certain favorable units of the pre-Cambrian Mescal limestone. This stratigraphic limitation, combined with other essential geologic conditions, tends to restrict the size of the deposits.Virtually all of the deposits are in rugged, mountainous country, and many of the mines are on steep canyon walls. In the average mine, production of 1 ton of commercial asbestos requires removal of 30 to 40 tons of waste rock. Mining and transportation costs consequently are high.Several deposits of chrysotile that is somewhat harsh and of moderate tensile strength have been known for years but were not worked because of the former exacting demands of industry for high-strength, soft asbestos. However, improve¬ments in asbestos fiberization and spinning technique, combined with the urgent need for asbestos, have made this so-called semisoft fiber desirable, and deposits of this type now are being exploited."

Jan 1, 1955

By C. C. Clark, R. R. Backer, J. D. Vickery

This report presents the results of tests conducted by the U.S. Bureau of Mines to determine the transport characteristics of highly concentrated paste backfill mixes made from dewatered total mine tailings. The slurry concentrations of the mixes were all above 78 pct by weight with slumps ranging from 6.4 to 16.5 cm (2.5 to 6.5in). Laboratory material property tests and full-scale pumping tests were conducted using pipe diameters of 102,128, and 154 mm (4, 5, and 6 in) and a positive-displacement pump. The results indicated that the tested backfill mixes can be successfully transported as a stiff paste and identified the influence of and the interaction among the various mix and system variables.

Jan 1, 1995

By B. K. Cantrell, K. L. Rubow

"Two source apportionment techniques have been applied by the Bureau of Mines to aerosol measurements in diesel equipped underground noncoal mines. The first technique is based on size selective sampling and the premise that the diesel exhaust fraction of the aerosol is predominately sub-micron in size while the mineral dust fraction of the aerosol is mostly super-micron in size. The second technique, Chemical Mass Balance (CMB) modeling, was used to referee the analysis of diesel and mineral dust aerosol concentrations with the size selective method.The size distribution data were modeled using a log-normal regression to parameterize the sub- and super-micron fractions of the sampled aerosol and to estimate the mineral and diesel contributions to each. For the mines visited, analysis of the size selective: samples yielded an average value for the fraction of the fine aerosol attributable.to mineral dust of 3 pct.'The CMB analysis, applied to both fractions of the respirable mine aerosol, yielded the amount contributed to each by the diesel· and dust aerosol sources. Less than 5 pct of the sub-microm fraction was mineral dust, however, as much as 20 pct of the diesel aerosol was found: ""in the super-micron fraction requiring a correction of the sub-micron fraction to account for the missing diesel mass. More accurate measurement will require a carbon specific analysis of the aerosol."

Jan 1, 1988

By D. L. Paulson

The Bureau of Mines studied the feasibility of producing copper matte in an electric furnace from blends of copper concentrate similar to those currently smelted in a gas-fired reverberatory system at an installation in Tacoma, Wash. A 800-kva electric-arc furnace was used to determine the distribution of constituents when arseniferous concentrates are being smelted in an electric-arc furnace. Test results from smelting 40 tons of materials indicated that electric smelting is more like a conventional gas-fired system than originally expected. Although gas composition over the molten bath is much different in an electric furnace, the secondary constituents such as arsenic, lead, zinc, and antimony behaved the same as in a reverberatory furnace. The results established that an electric furnace would be compatible with sulfur and particulate recovery facilities that are being used.

Jan 1, 1976

By H. G. Wolfhard

The mode of propagation of explosions through narrow passages is important for understanding flameproofed equipment employed in mines. Narrow channels have been used in this investigation that connected between a small explosion chamber and a large chamber containing fuel-air mixture. The oxygen index of the mixture in the small chamber was determined which caused an explosion in the outer chamber. Preliminary measurements have already been given in Bureau of Mines Report of Investigations 5457 and suggested that) flames do not pass through narrow channels. The hot, burned gases from the explosion in the small chamber, however, are able to ignite the mixture in the large chamber by a process of hot-gas ignition. Systematic measurements are reported in the present paper that cover the influence of channel length and diameter and the properties of the gas mixtures in the large chamber on the transmission of explosions. The influence of such properties as quenching diameter and flame temperature is also discussed. This paper concludes the work on this problem and presents a theory that describes in detail parameters that influence transmission of explosions through narrow channels. INTRODUCTION Flameproofed equipment in mines is usually provided with flanges. A gap between the opposing flanges allows ventilation and release of pressure. The safe gap width has been determined for a number of flange lengths by Smith4/

Jan 1, 1959

By Ronald D. Hill, Elmore C. Grim

Sediment is one of America's greatest pollutants. More than a billion tons of sediment reach the major streams of the United States annually(l). Damages are reflected in the reduced carrying capacity of streams, clogged reservoirs, destroyed habitat for fish and other aquatic life, filled navigation channels, increased flood crests, degraded facilities for water-based recreation, increased industrial and domestic water treatment costs, premature aging of lakes by enrichment of the water with silt-carried fertilizer that promotes algae growth, destroy crops, and reduce productivity of flood plain soils. Erosion and sedimentation are natural processes that are usually gentle actions releasing controlled amounts of silt from watersheds to receiving streams. Surface mining activities accelerate these natural processes and short duration, high intensity storms can become a violent force moving thousands of tons of soil in a brief period of time. Cover is a very important factor. With the removal of ground cover, water moves across the denuded area on its own terms picking up soil particles as it flows and leaving gullies behind. The susceptibility of strip-mined land to erosion depends on: 1.Physical characteristics of the overburden 2. Degree of slope 3. Length of slope 4. Climate 5. Amount and rate of rainfall 6. Type and percent of vegetative ground cover. By development of erosion and sedimentation control plans before disturbance of the area, many of the detrimental effects of strip mining can be prevented.

Jan 1, 1974

By James E. Hill

In the course of exploratory drilling during World War II by the Bureau of Mines under the Strategic and Critical Minerals investigations Program, a problem arose as to the ultimate disposal of the drill core resulting from that program. The difficulties experienced in obtaining factual information to evaluate mineral deposits examined (during that program) influenced the Bureau in a decision to catalog and store the drill cores for future reference. Initially, the drill cores were stored at the nearest Bureau of Mines station that had space available for the purpose. Recently the Bureau stations at Minneapolis, Minn., and Denver, Colo., were designated as the locations of permanent drill-core storage facilities. Drill cores that are retained from Bureau of Mines mineral-exploration projects are stored at these two locations and are given preference in selecting cores for storage. Drill cores are accepted also for storage from other Government agencies, State agencies, private companies, or individuals on the basis of available facilities and consistent with the significance of the core in relation to Bureau of Mines objectives and national interest. Selection and acceptance of such drill core are determined by the Bureau of Mines. The drill cores stored at the two locations are available for inspection by any person having a legitimate interest in the mineral deposits represented by the cores. Approximately 1,850,000 feet of drill core can be stared in the facilities now available to the Bureau of Mines. Approximately 475,000 feet of drill care is stored or scheduled for storage at Minneapolis, Minn., and 240,000 feet of core stored or scheduled for storage at Denver, Colo. A list of drill core now in storage at the Bureau of Mines core-storage facilities at Denver and Minneapolis is included as appendix A.

Jan 1, 1957

By Paul T. Allsman

THIS CHAPTER reviews the highlights of developments in mining technology during 1956 and presents a special report on the design of mine openings in stable ground. This special report is presented each year in an endeavor to stimulate use of the scientific approach to the solution of problems related to mining technology. Assuming that the literature on mining technology reflects trends in mining, it appears that two areas of activity were given most attention in 1956. One was research on mining technology,4 and the other was improvement of transportation, particularly trackless transportation, both at surface and underground mines.

Jan 1, 1958

By Alexander May

In its role to provide technology to prevent or limit adverse environmental impacts associated with mining or minerals processing, the Bureau of Mines has conducted research at its Tuscaloosa Research Center to asess the environmental impacts of phosphogypsum produced by the Florida phosphate industry. Over the years, stockpiles containing 335 million tons of phosphogypsun have accumulated and the industry continues to generate an additional 33 million tons a year. Samples from approximately 1,000 feet of drill core, obtained from nine stockpiles were characterized using chemical, X-ray diffraction, emission spectrographic, radiological, and physical means. The data developed indicated that phosphogypsum is not a corrosive or toxic hazardous waste as defined by Environmental Protection Agency criteria. Radium concentration averaged 21 picocuries per gram and its content was inversely related to particle sizes. Thirty-nine elements were detected in phosphogypsum; concentrations of these elements did not vary with depth within the stockpiles.

Jan 1, 1982

By J. D. Dixon

The Bureau of Mines investigated the principles of support-rock interaction, based on structural matrix methods which permit mathematical formulation of the problem and computer solution. The principles are given under two main sections: the first discusses the idealization of the tunnel support structural system for matrix analysis; the latter discusses the analysis procedures necessary for carrying out the solution. A general frame matrix computer program and a medium-size computer should be sufficient for carrying out the procedures involved. The example problem consists of a circular tunnel support which is subjected to a uniformly distributed vertical load, Three wall thickness-radius ratios are studied in combination with four support-rock modulus ratios. This problem illustrates the main procedures of the support-rock interaction analysis involved, and examination of the results reveals the influence of the relative rigidities of the support and the rock.

Jan 1, 1971

By C. M. McCulloch, Maurice Deul

A geologic study of Mines 32 and 33 in Cambria County, Pa., was conducted as part of a methane control research program. Areas of high methane emission and roof instability are encountered which are related to the structural and stratigraphic features that characterize the geologic setting of these mines. Locally the folds trend N 20° E ±2°, the direction of the butt cleat in the Lower Kittanning coal. The face cleat strikes at N 69° W ±2° and the systematic rock joint in the surface bedrock strikes N 67° W ±2°This suggests that a directional stress oriented N 70° W produced the folds and influenced the directions of coal cleat and systematic joint sets. Analysis of SLAR indicates three directions of prominent regional lineation: N 39° E, N 31° W, and N 70° W. Little gas was encountered during development mining; large volumes of gas are encountered when roof falls. Most of the gas comes from strata above the mined coal; therefore, to control methane, roof instability must be controlled. Roof falls and high rates of methane emission are most likely where less than 30 feet of many thin layers of limestone, shale, and sandstone occurs between the Lower Kittanning coal and the next coal and in zones along the margins of a sandstone channel.

Jan 1, 1973

By R. Pakalnis, Richard P. Curtin, Lewis A. Martin

Instrumented cable bolts developed at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health were used in conjunction with existing ground control to monitor rock mass loads at various field sites (FMC Granger, Getchell, Meikle, SSX, K-2, and Stillwater). Axial and shear loads were determined by strain gauges to levels of instrument accuracy of ±5 N or ±5 microstrain as these loads were transferred to the instrumented cable bolts. These gauges were 12.5 mm long and embedded into are manufactured king wire that replaced the conventional king wire. Cable bolt performance, quality of grout, and installation techniques were also assessed. By using instrumented cables, a mine operator can determine axial load along the cable at predefined gauge locations. By monitoring load on and displacement of the rock mass, more effective ground support can be selected and installed, which will lead to safer working conditions for miners.

By Noel N. Moebs

This report summarizes 10 selected Bureau of Mines research contract reports produced from 1970 to 1980 which consist largely of geologic studies of coal mine roof support problems. Significant highlights from the contract final reports are discussed and presented in practical terms. The selected reports focus on the Appalachian and Illinois coal mining regions. In the Appalachian coal region, two geologic structures, roof rolls and slickensides, predominate over all structures as features that directly contribute to roof falls. Studies of these and other structures are reviewed, and improved methods of utilizing drill core and core logs to prepare hazard maps are presented. Among the reports described are several on the weakening effects of moisture on shale roof, as determined from both laboratory and underground measurements, and an assessment of air tempering as a humidity-control method. Also summarized are findings concerning the time lapse between roof exposure and permanent support installation as a factor in the effectiveness of roof bolting.

Jan 1, 1984

By R. E. Head, Virgil Miller

"Under existing conditions in the treatment of oxidized lead ores containing small quantities of molybdenum no provision is made for the recovery of the molybdenum. Considerable quantities of this important element are lost in the slags of the lead smelters and constitute an economic waste. There is little or no probability that slag dumps containing molybdenum in small quantities could be economically treated for the recovery of the element, and steps for the prevention of waste in this respect must be taken prior to smelter treatment.Wulfenite, lead molybdate (PbMo04), and molybdite, molybdic ocher (Mo03), are the molybdenum minerals most abundantly found in deposits of oxidized lead ores. Wulfenite contains 39.3 per cent molybdenum trioxide and 60.7 per cent lead oxide; molybdite contains 66.7 per cent molybdenum and 33.3 per cent oxygen. Plumbojarosite, argentojarosite, cerussite, and occasionally anglesite are commonly associated with wulfenite ores, and the oxidized iron content is usually fairly high.The recent discovery and development of a body of wulfenite ore in the Star district near Milford led to a cursory microscopic examination of samples of the ore, followed by a few preliminary tests which had for their object the separation and recovery of the lead and molybdenum in separate products.The microscopic examination showed that the samples used in the work were composed of wulfenite, plumbojarosite, and a small quantity of cerussite, and indicated that the iron content was quite high. The ore was porous and yellowish-brown; crystals of wulfenite appeared to be quite uniformly distributed through it, and this mineral and plumbojarosite (Pb0.3Fe203.4S03.6H20) apparently accounted for the major part of the lead content, although lead"

Sep 1, 1928

Table 1.-Salient aluminum statistics (Thousand short tons and thousand dollars) [ ]

Jan 1, 1967

Exposure to airborne respirable crystalline silica dust can lead to silicosis, a debilitating lung disease. On surface coal mining and construction sites, blast hole drills are notorious sources of airborne respirable dust that may contain significant amounts of silica. The drill operator and drill helper usually receive the greatest silica exposure compared with other occupations. As a result, many drilling operations have been, and still are, on more stringent dust standards. Drilling through various rock formations naturally presents a strong potential for silica dust generation for several reasons. First, drilling is a pulverizing process that generates large amounts of very small dust particles. Second, the bailing air used to flush cuttings from the hole leaves the hole at a very high velocity and can be difficult to contain. Third, many fixed shrouds used to enclose the area beneath the drill deck have a significant amount of leakage due to 1) gaps between the shroud and ground created by raising/leveling the drill, 2) gaps in the corner seams, and 3) tom deck shrouds. CONTROLS A dry dust collection system is typically connected to the drill deck to collect dust as the bailing airflow transports the cuttings (and significant amounts of airborne respirable dust) out of the drill hole. Deck shrouds are installed in an attempt to enclose the volume around the drill steel and prevent dust escaping. However, most deck shrouds are rectangular and constructed of four separate pieces of rubber belting attached to the deck. Because of this design, there is usually a significant amount of dust escaping from the open seams as well as the open area between the shroud and the ground. This dust can be a significant source of silica exposure to drill operators as well as other personnel downwind of the drill.

By Frank E. Cash

"INTRODUCTION The producing iron-ore ranges in the Lake Superior district are the Marquette and Menominee in Michigan, the Gogebic in Michigan and Wisconsin, and the Cuyuna, Mesabi, and Vermilion in Minnesota. These ranges produce about 85 percent of the iron ore mined in the United States. The accident experience in connection with this production is better than that of the regions producing the remaining 15 percent. Production and shipments vary slightly from year to year owing to stockpiling underground ore during the winter, or nonshipping, season but closely approximate each other over a period of years. This information circular supplements, combines, and continues the data contained in Information Circulars 7321 3/ and 7410 4/, including statistics for 1946 and 1947.Whereas the title ""Accident Experience"" is used for uniformity and logical indexing throughout this report, ""injury"" will be used as a general term to apply to disabilities of all degrees.During the 8-year period 1940 to 1947, inclusive, 619,054,023 long tons of iron ore was shipped from the Lake Superior district. 5/ Michigan and Wisconsin shipped 117,828,939 tons, or 19.03 percent of the total, and employed approximately 9,260 men. Minnesota shipped 501,225,084 tons, or 80.97 percent of the total, and employed an approximate annual average of 12,260 men. The tons produced and shipped per man employed in Minnesota is much greater than in Michigan and Wisconsin, owing to the large open-cut production in Minnesota."

Jun 1, 1949

From the National institute for Occupational Safety and Health Disasters take many forms and demand quick response from emergency workers. They may include natural disasters such as earthquakes or hurricanes, or they may involve manmade disasters such as technological failures or terrorist attacks. As a member of an emergency response team, you and your team members are at risk of experiencing what psychologists refer to as a traumatic incident—an incident that may Involve exposure to catastrophic events, severely injured children or adults, dead bodies or body parts, or the loss of colleagues, for instance. Traumatic incidents can produce unusually strong emotional reactions that may interfere with your ability to function at the scene or later: You may experience any of the physical, cognitive, emotional, or behavioral symptoms listed below in Table 1. Some people experience emotional aftershocks weeks or months after they have passed through a traumatic event. Others may experience these reactions while still at the scene, where they must stay clearly focused on constantly changing hazards to maintain their own safety and to rescue injured victims.

By J. S. Dunning

A primary goal of the Federal Bureau of Mines is to minimize the requirements for scarce mineral commodities through conservation and substitution of more abundant elements, such as iron and molybdenum. One example of this is the research effort to devise substitute materials for specialty alloys, thereby conserving nickel and chromium in high-volume stainless steels. As a possible substitute for the solid solution strengthening of chromium and nickel, the precipitation hardening characteristics of a number of binary iron-based systems in which Laves phase precipitates, such as Fe2Mo, are formed were investigated. Several hardening responses were observed, but none were ideal. The Fe-Ta binary system had the highest magnitude of hardening, even with low alloy additions, and the Fe-Mo system had unique stability at temperature. Accordingly, the Fe-Mo-Ta system was selected for study to determine if a ternary Laves phase could combine high hardening with long-term stability at elevated temperature. Hardening and stability were reflected in excellent elevated temperature, tensile, and stress rupture strengths. Future research will study ternary systems based on more abundant resource materials, such as the Fe-Mo-Ti system, together with additions, such as aluminum and minimal chromium, to provide oxidation resistance.

Jan 1, 1979

By A. L. Engel

This publication describes further research by the Federal Bureau of Mines in beneficiating domestic manganese ores. The ores selected for treatment were typical of many manganese deposits in California and Nevada in that they have not been economical to mine because they are low grade or contaminated with siliceous minerals and are not amenable to physical concentration.3 4/ It would be desirable to develop a simple treatment method resulting in nearly complete extraction of manganese from these ores and applicable to small-scale operations. Sulfation reduction appeared to be such a method. The studies reported in this publication were directed toward sawdust or lignin-sulfonates as reducing agents. Sawdust, as waste from lumbering, and lignin-sulfonates, byproducts of woodpulp papermaking, are comparatively cheap and may be available in areas where manganese ores are found. Sugar, oils, and coal were also tried as reducing agents.

Jan 1, 1960