Search Documents

By T. E. Gray

This report describes the preparation characteristics of the significant coalbeds in Boone County, W. Va., as determined by the Bureau of Mines. It is one of a series describing the coals suitable for producing metallurgical coke, either as mined or after beneficiation. Over 6.3 million tons of coal was produced in Boone County, W. Va., in 1959, of which almost 5.5 million tons was mechanically cleaned in eight preparation plants. On December 31, 1959, it was estimated that almost 8 billion tons of coal remained in the county in beds 24 inches or more in thickness. Thirteen samples were collected from nine coalbeds and washability tests were made on these samples.

Jan 1, 1961

By George A. Morgan

Mineral production was confined to out-put of cement and gravel. However, exploration was being conducted by the U.S.S.R. and the United Nations Development Program. Development of a domestic limestone deposit and crude oil from an offshore oilfield was underway. Benin's currency remained fixed to the French franc. The gross domestic product (GDP) was $977 million in 1981, the latest year for which information was available. 2 COMMODITY REVIEW Cement.-Construction of a cement plant with 500,000 tons per year capacity neared completion at Pobé. The operator of the plant, using locally produced limestone, was the Societe des Ciments d'Onigbolo, a joint venture between Benin and Nigeria. Nigeria was expected to utilize most of the cement produced. Equipment for the plant included a 1,600-ton-per-day, oil-fired pre-heater.

Jan 1, 1984

By Warren E. Morrison

Demand for energy in the United States in 1965 was stimulated by the continuing expansion of the economy. A gain of 5.9 percent in gross national product for the year was accompanied by a 4.4-percent rise in energy consumption. Domestic energy resources met about 93 percent of the nation's requirements. The remaining 7 percent consisted of imported fuels, mainly of crude petroleum and residual fuel oil. The major fossil fuels-natural gas, crude petroleum, and coal, in that order-contributed 96 percent of all commerical energy utilized, with the balance of 4 percent being primary electricity from hydropower and nuclear power plants. Production was up for all of the major mineral energy resources in 1965, with the single exception of anthracite, output of which continued to decline. Bituminous coal output for the year was 512 million tons; marketed production of natural gas, 16,039 billion cubic feet; and crude petroleum output, 2,848 million barrels. Among the secondary products processed from primary energy resources, the most significant gains were in coal carbonized for coke which increased 6.7 percent to 95 million tons, and in the output of liquefied gases from natural gas which rose 4.8 percent to 11,257 million gallons (268 million barrels). Within the latter category, the off? take for petrochemical feedstocks continued to rise at a very rapid pace.

Jan 1, 1967

By Charles L. Kimbell

For a study such as this, which summarizes and amalgamates much information collected, compiled, and utilized by the numerous U.S. Bureau of Mines country specialists and branch chiefs for inclusion in the country and regional reports that comprise the five other sections of 1991 Minerals Yearbook-International Review, it is clearly impossible to cite all sources of information used in its presentation, but some recognition is due. Generally speaking, this study and its related detailed studies on countries and areas would be much more difficult, if not impossible, without the efforts of the personnel of national mining and geological agencies throughout the world. Information that they collect, compile, and then publish, either in their own volumes or those of central statistical agencies in their countries, are the foundations on which this work rests. Thus, appreciation is expressed to the multitude of persons employed by these agencies.

Jan 1, 1993

By Robert L. Rough

This report presents the results of an investigation by Federal Bureau of Mines engineers of water-injection projects in the northwestern Pennsylvania and southwestern New York area, where oil-producing wells have been converted from pumping to flowing. Data from 24 leases converted to flowing were collected and examined. Only 10 leases had information of significant scope for inclusion in the final analysis. The projects were classified in one of two categories. Group I consisted of leases operated to permit an evaluation of operational changes in terms of existing pressure differentials between injection and producing wells. Group II included remaining properties, for which enough information was available to justify an economic analysis but which did not have sufficient production data to support an engineering study because of radical changes in operational techniques. Variations in production and costs resulting from conversion to flowing were examined for production methods, well-spacing and completion techniques, and reservoir characteristics. Where water-injection rates were constant, oil production usually decreased rapidly at the time of conversion; production then increased slightly for 6 to 8 months before resuming a normal decline rate considerably below the estimated pumping rate. The abrupt decrease in production after conversion is indicative of lower pressure differentials between injection and producing wells, caused by the increased hydrostatic head in the producing wells.

Jan 1, 1960

By Thomas L. Chapman

The San Manuel is a deposit of low-grade disseminated copper ore. It was brought to the attention of the government in October 1942 through an application to the Reconstruction Finance Corporation for a development loan, supported by a report by Henry W. Nichols. Nichols' sampling of two outcrops containing copper silicate and his geologic map indicated that a minable body of copper ore might be developed. The Federal Geological Survey was requested to examine the property. The Survey mapped the geology in March 1943 and cut a few check samples, which substantially confirmed Nichols' sampling of the outcrops and a few shallow workings. The geologists of the Survey recommended some test drilling by the Bureau of Mines. The property was examined by the author and Wm. D. Hughes, associate engineer of the Bureau of Mines on March 22 and 26, 1943, and a preliminary drilling campaign was recommended. Five shallow churn-drill holes totaling 1,480 feet were put down under the supervision of Chas. A. Kumke, one of the Bureau's engineers, from November 23, 1943, to January 13, 1944. This work indicated that the deposit extended deeper than the 350-foot depth attained in the deepest hole and might have very considerable areal extent. Additional funds were allotted, and the drilling contract was extended twice to a final maximum of 17,000 feet with 2,000 feet maximum depth of hole. Drilling was continued by the Bureau of Mines until February 2, 1945, when 15,844 feet of hole had been drilled. The Magna Copper Co. took options on this and adjoining property in September 1944 and commenced drilling with two machines. It also engaged the two contract drills used by the Bureau after it stopped drilling. It exercised its options in August 1945 and organized the San Manuel Copper Corp. to operate the property. That company is continuing to explore the ore body with six churn drills. Thomas Lyon took options early in 1945 on holdings adjoining the San Manuel property on the east and is operating two churn drills. Exploration up to the completion of the last holes started by the Bureau of Mines indicated a block of ore 3,100 feet long, 400 to 800 feet wide, and 500 to 900 feet thick, and averaging about 0.8 percent copper. Subsequent drilling showed that the ore body extends considerably beyond this block. The axis of the ore body strikes about N. 61° E. Copper minerals are disseminated in hydrothermally altered quartz monzonite and monzonite porphyry. Ore outcrops in two small areas over the northeast part of the block. Elsewhere the copper-bearing rocks are capped by Gila conglomerate, which thickens toward the west and south. Drilling showed that the ore is in a thick, tabular body with a steep dip to the south. The ore body lies near the surface in the northeastern part of the block. The south side of the block is much farther below the surface than the north side. There the upper part of the copper-bearing rocks is lightly mineralized, so that the hanging wall of minable ore lies deeper than the base of the conglomerate cap, which thickens southward.

Aug 1, 1947

By Charles L. Kimbell

For a study such as this, which summarizes and amalgamates much information collected, compiled, and utilized by the numerous U.S. Bureau of Mines country specialists and branch chiefs for inclusion in their country and regional reports that comprise the five other volumes of the international studies of the Minerals Yearbook, it is clearly impossible to cite all sources of information used in its presentation, but some recognition seems due. Generally speaking, this study and its related detailed studies on countries and areas would be much more difficult, if not impossible, without the efforts of the personnel of our counterpart agencies throughout the world. Information they collect, compile, and then publish, either in their own volumes or those of central statistical agencies in their countries, are the foundations on which this work rests. Thus, we must begin by expressing our appreciation to the multitude of persons employed by these agencies for their contributions.

Jan 1, 1993

By A. W. Fahrenwald

The art of flotation has developed rapidly. Numerous technical staffs and individual investigators have, by their combined efforts, developed practicable methods of concentrating ores which ten or even five years ago were considered complex and impossible of commercial treatment. Also the work of those who have been engaged in pure research on the fundamentals of flotation has helped greatly to expedite the general development of the process. However, in spite of the highly successful practical operation of the flotation process, results are obtained and things happen that we are unable to explain completely, although much is known about the theory of the process. The rapid stride in flotation concentration, it is noteworthy to point out, is due to the freer exchange of facts and data by the staffs of the larger mining companies and the patent controlling corporations, and by investigators in general. Generally speaking, one may visit any mining plant and by presentation of proper credentials, be shown all that is going on or that is being done.

Jan 1, 1925

By T. E. Gray

This report describes the preparation characteristics of the most significant coal beds in Wise County, Va. It is one in a series of reports planned to determine coals suitable for the production of metallurgical coke, either as mined or after beneficiation. Wise County produced approximately 6,600,000 tons of coal in 1955, of which about 2,110,000 tons was cleaned mechanically. The Federal Geological Survey has estimated that 1,341 million tons of measured and indicated coal reserves remained in the county as of January 1, 1951.

Jan 1, 1958

By Noel N. Moebs

Studies by the Bureau of Mines have identified geologic structures in mine roof rock that contribute to many roof falls in Appalachian coal mines. These structures, including paleochannels, scours, pinchouts, slickensides, clay veins, crevasse splays, and joints, can often be identified during, and sometimes before, mine development. Mine projections can be revised to reduce the adverse effects of discontinuitites in roof structure; large roof areas of laminated sandstone or incompetent strata generally can be delineated or inferred from exploratory drill hole data, and the need for supplementary support can be anticipated. Accurate descriptions of roof geology also provide some indication of optimum length and type of roof bolts that should be installed.

Jan 1, 1981

By Martin Hertzberg

The concept of limit burning velocities is being used to formulate a quantitative theory of flammability limits. Competing and complicating processes dissipate power from a combustion wave and quench propagation at some characteristically low limit velocity. Two earlier reports dealt with process (a), natural convection (RI 8127); and with process (b), conductive-convective wall losses (RI 8469). This report considers process (c), radiative losses, and process (d), selective diffusional demixing. The limit burning velocity for radiative losses is [(SU)c ~ e cp] It is normally not a significant process for premixed gas flames; however, for laminar flame propagation in a gravity-free environment, it is the only loss process present. Accordingly, limit velocities at zero gravity should be much lower than on earth, and premixed gases should be flammable over wider composition ranges. For highly emissive dusts, soot, or ash-forming flames, radiative losses are significant even under normal gravity conditions. Selective diffusional demixing is a complication that manifests itself in the form of cellular flame structures and wide gaps in composition between upward and downward propagation limits. It induces a burning velocity shift (?Su)d, causing the flame to behave as though it were richer or leaner than its initial composition, depending on whether the fuel or the oxidizer mole¬cule has the higher diffusivity. A simple pertubation analysis shows that the process generates stable cellular flames whenever [dsu] > 0, where ci is the concentration of the reactant with the higher diffusivity. The same analysis indicates that at the opposite stoichiometry, where [dcu] < 0, laminar structures are stabilized. A simple formula for the diameter of cellular flames is derived, which predicts that dcell should vary inversely with the product of the diffusivity difference Di -DJ, and the burning velocity slope [dc ]. Those predictions are in good agreement with the available data. Buoyancy forces for upward propagation induce flame front curvature, and hence buoyancy and selective diffusion are mutually supportive in upward propagation. Thus large gaps in composition between upward and downward limits are present in those composition domains where cellular flames are stable.

Jan 1, 1981

By Richard L. Rains

The 15,770-acre Worm Creek Roadless Study Area is in southeastern Idaho about 8 miles (mi) west of the northern portion of Bear Lake. U.S. Bureau of Mines personnel examined the roadless, area during the summer of 1984. No mineral resources were identified within the study area. There were no mines or mining claims in the study area in 1984. However, the study area is blanketed with oil and gas leases, but no known productive horizons have been identified within nor nearby. The roadless area is in the Cordilleran fold-thrust belt and is underlain by Paleozoic and Mesozoic marine strata more than 50,000 feet thick. The trace of the Paris thrust fault is 2 to 3 mi east of the study area and has an eastward displacement of about 4 to 7 mi.

Jan 1, 1985

By W. E. Webb, R. H. Church, W. G. Hopkins

The development of systems for location of miners who have become entrapped following a mine disaster has been one of the major research goals in the Bureau of Mines. This study details the preliminary development of such a system. Current technologies for locating trapped miners from the surface are either simple direction, finders or time difference pulse systems that have accuracy Limitations. Developing technologies using full vector field measurements at several receiving points are currently being studied. The necessity of measuring field strength with great accuracy can be a drawback in these systems. A system that operates with continuous wave radio signals, whose phase differences can be measured accurately even in weak signal conditions, greatly improves the location accuracy. A microcomputer would be used, in conjunction with the system, to gather and manipulate the data to automatically pinpoint the location of the trapped miner. Comparison of this system with existing technology indicates a favorable accuracy/complexity ratio for the phase difference of arrival technique.

By J. E. Zeilinger

This Bureau of Mines report describes the preparation characteristics of the significant coalbeds of Clarion County, Pa. Of the 15 samples collected, 1 was of metallurgical quality as received, 4 could be sufficiently upgraded to provide acceptable products, and the remaining 10 samples could not be upgraded to metallurgical quality because their sulfur contents could not be lowered to meet the standard. For steam or power generation, 1 sample was of low sulfur content as received, 1 sample could be upgraded to low sulfur content, and 10 samples could be upgraded to medium sulfur content. The original sulfur content of the remaining three samples can be appreciably reduced by removal of the sink 1.58 specific gravity material; however, these coals would be classified as medium sulfur coals both before and after removal of the sink material.

Jan 1, 1968

By J. G. Donaldson

The Bureau of Mines investigated the formation of boron and boron-carbide coatings by vapor-phase reactions. Optimum parameters were determined for hydrogen reduction of boron trichloride and for the fonnation of boron-carbide coatings on graphite by reaction with the depositing boron. At 1,300° C, about 85 percent of the boron was deposited. Tungsten substrates did not react with the boron deposit; other substrates reacted to various extents. The hydrogen reduction of boron tribromide was briefly investigated. Boron carbide was deposited at 1,300° C by adding methane to the boron trichloride-hydrogen feed gas. The chemical composition of the vapor-deposited boron carbide approximated B4C. A method of etching B4C was developed to study its microstructure. When boron was deposited on graphite at 1,500° C, very hard, uniform, strongly adherent coatings of B4C were formed that might be useful in rocket nozzle applications.

Jan 1, 1968

By J. J. Wallace

1. The Pittsburgh is the most important bed in Greene County from the standpoint of present production and recoverable reserves. 2. Known measured and indicated reserves in all beds, based on a minimum thickness of 14 inches and 1,800 short tons per acre-foot of coal in place, are estimated at 6,011 million short tons as of January 1, 1954. Of this total, 5,967 million short tons is in beds 28 inches and more thick. Areas in some beds were omitted from the estimate because available data relative to the bed characteristics are too meager to make an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves.

Jan 1, 1955

By Ramie H. Thompson

1.1 BACKGROUND In many underground coal mining operations the use of electromagnetic field equipment, particularly communication systems, not only increases the overall efficiency of the mining operation but can be directly linked with mine safety considerations. The use of electromagnetic field producing equipment in underground coal mining operations can only be expected to grow. Several new communication systems have already been proposed. In addition, high-frequency producing equipments for many diverse uses in mining operations are under study. The use of these equipment in underground mining operations is hampered by the possibility of their electromagnetic fields interacting with the electric blasting cap operations commonly carried out in the mines. Such interactions can have at least two results bearing directly on mine safety: o premature initiation of the cap, either in its normal shot location or during hookup or transportation; o dudding of the cap so that normal firing operations do not cause irritation; thereby leaving unexploded high explosives after normal firing. Since the consequences of a premature initiation could, particularly in coal mines operations, result in catastrophe involving human life, the overall approach to prediction of possible hazard must be, as far as possible, of a "worst case" nature. The general problem of predicting possible RF hazards for any electroexplosive device (EED) is best treated by reference to Appendix A of

Jan 9, 1983

By D. B. Taliaferro

An accurate knowledge of the water content of oil-bearing sands4/ now is recognized as an important factor in calculations of the flow of oil through the sands to producing wells and in the estimation of oil reserves. To this end the Bureau of Mines laboratories are using a method that is an adaptation of the A. S. T. M. method of determining the water content of petroleum products (1).5/ However, the apparatus and technique have been altered slightly, as described in this report, to increase the precision of the method without affecting the simplicity of procedure or speed with which determinations may be made. Until recently petroleum engineers, when estimating reserves assumed that the entire pore volume of the oil-saturated parts of producing sands was filled with oil, as it was generally thought that the oil, water, and gas in any formation had separated completely during geologic time into distinct layers because of their difference in density. In 1929 Lindthrop and Nickolaeff (12) reported experimental results from which they concluded that 22 to 30 percent of the pore volume of producing sands in the Grozay district, Russia, was filled with water when the fields were discovered. Since that time numerous investigators (5, 7, 8, 10) have found evidence of water in the sands of now oil-producing fields and old fields that never produced water with the oil.

Jan 1, 1940

By D. B. Taliaferro

An accurate knowledge of the water content of oil-bearing sands4/ now is recognized as an important factor in calculations of the flow of oil through the sands to producing wells and in the estimation of oil reserves, To this end the Bureau of Mines laboratories are using a method that is an adaptation of the A. S. T. M. method of determining the water content of petroleum products (1).5/ However, the apparatus and technique have been altered slightly, as described in this report, to increase the precision of the method without affecting the simplicity of procedure or speed with which determinations may be made. Until recently petroleum engineers, when estimating reserves assumed that the entire pore volume of the oil-saturated parts of producing sands was filled with oil, as it was generally thought that the oil, water, and gas in any formation had separated completely during geologic time into distinct layers because of their difference in density. In 1929 Lindthrop and Nickolaeff (12) reported experimental results from which they concluded that 22 to 30 percent of the pore volume of producing sands in the Grozay district, Russia, was filled with water when the fields were discovered. Since that time numerous investigators (5, 7, 8, 10) have found evidence of water in the sands of now oil-producing fields and old fields that never produced water with the oil.

Jan 1, 1940

By D. S. Burgess

The characteristics of gas-phase detonations were observed in 20 instrumented firings within earthen tunnels, in 100 such detonations in a 24-in-diam by l63-ft-long steel pipe, and in about 200 smaller scale firings. Most of the fuels studied were representative hydrocarbons--acetylene, propane, gasoline, and a roughly equimolar mixture of methylacetylene, propadiene, and propane. In a pipe with two closed ends, the detonable limits were demonstrated to be very nearly the same as reported limits of flammability. The side-on impulses (pressures integrated over 200-msec intervals) were shown to be the same function of concentration regardless of whether deflagration or detonation had occurred. In a pipe with only the initiation end closed, the impulses of all fuel-air systems tended toward the same level when averaged over comparable ranges of fuel concentration; the lower pressures with saturated hydrocarbons were nearly compensated by longer durations of pressure transient. In all fuel-air systems, unexpectedly high impulses were obtained with slightly lean mixtures. In earthen confining structures, the impulse, of the explosion was efficiently converted into momentum of the failing wall. In the configurations studied, an earth velocity of about 20 fps was critical to overcome the soil&apos;s resistance to shear. The destructive effect was determined by gas pressure rather than by total energy release. The assignment of a "TNT equivalent" to an explosive gas mixture is discussed in terms of the confinement of the mixture.

Jan 1, 1968