Search Documents

By Cavallaro. J. A.

This report presents the results of a washability study of 455 raw coal channel samples with special emphasis on sulfur reduction. These raw coals contained on the average 14.0 percent ash, 1.91 percent pyritic sulfur, and 3.02 percent total sulfur. The complete washability data are presented for each sample processed. A statistical evaluation is included for the coalbeds from which more than 10 samples were collected and for the geographical coal producing regions. A graphical summation is presented for the coal producing regions and selected coalbeds. Finally a similar statistical evaluation is included showing composited data interpolated at Btu recovery levels of 50, 60, 70, 80, 90, and 100 percent. Graphical summations are presented for the various coal producing regions. Generally, significant sulfur reduction is achieved if the coals are crushed to a finer size and the higher specific gravity increments are removed. If a 50-percent Btu recovery was acceptable, then 32 percent of the samples tested could be upgraded to meet the current Environmental Protection Agency (EPA) standard of 1.2 pounds of S02 emission per million (MM) Btu when crushed to 14-mesh top size and separated gravimetrically.

Jan 1, 1976

By I. S. Solet

This study, of the liquidus temperatures and densities of molten alloys of zinc and aluminum was made as part of a broader investigation on refining of scrap aluminum. One of the methods of refining involves the separation of liquid and solid phases by gravity segregation and by filtration. More accurate data were required on the liquidus temperatures and the densities of molten' mixtures of the metals than were available in the technical literature. New data on the liquidus curve were obtained by thermal analysis. The new temperatures are, for the most part) somewhat higher than those reported previously by other investigators. The density of molten mixtures of zinc and aluminum were found to be less than would be calculated by assuming that the two metals occupy the same respective molal volumes in solution as they do as pure metals.

Jan 1, 1949

By Doris M. Hyde

Mineral industry activity in many of the smaller Caribbean Island countries has remained minimal. For this reason, specific references to Bermuda, Guadeloupe, Martinique, and the Netherlands Antilles have been removed from textual and trade table presentations. Any significant future developments will be reported as they occur. Readers are referred to earlier Minerals Yearbook editions for previous information. Table 1 production statistics have been modified in some instances. References to certain nonmetal commodities were eliminated because information has often been unreliable. Their inclusion in table 1 was not considered important to either an overview of the area or to compatibility with volume I of the Minerals Yearbook.

Jan 1, 1984

By Kathleen Madland Kowalski

In recent years the issue of human stress response in emergency workers has begun to receive attention. This paper presents a rationale for considering human stress as a significant factor in the management of emergencies. It discusses the concept of stress, Critical Incident Stress in emergency responders, and introduces the Critical Incident Stress Debriefing (CISD) process. It is suggested that, in a disaster, the CISD process can improve the effectiveness of response teams on site, their turnaround time on site, and post disaster time off the job. This paper, prepared by a US Bureau of Mines research psychologist, offers some ideas to the mining industry in general, mine rescue trainers, and more universally, to those responsible for developing emergency management plans.

By Richard H. Spencer

Since the passage of the Coal Mine Health and Safety Act of 1969, the Bureau of Mines has made many advances in mine communications. These efforts have resulted in the following developments and demonstrations: Surface-to-surface electromagnetic transmission of baseband voice signals through overburdens as deep as 600 feet. This transmission was achieved with equipment from the Interim Mine Rescue and Survival System Program, and demonstrated that baseband voice communications could be obtained through these overburdens in the absence of mine-generated noise; that is, when the mine power system was shut off, However, during mine operational conditions, the mine-generated noise proved to be so large that effective baseband voice communications to the desired depths could not be effected.

Jan 1, 1975

By McHenry Mosier

This paper describes the practice in diamond drilling blast holes and discusses the relative merits of this method as compared with drilling by percussion rock-drills at eastern magnetite mine A. The rooke that were drilled included: (1) Gneiss; (2) sohist; (3) crystalline limestone; and (4) granular masses of magnetite. The principal stoping methods were: (1) Sublevel open stoping and (2) inclined room-and-pillar. Diamond drilling was used in the sublevel stopes and in some of the large pillars in an old section of the mine. Experimental work on diamond drilling blast holes began in 1943. Drill- ing proved difficult owing to the occurrence of fingers of extremely hard barren rock in the magnetite ore. All diamond drilling was contracted to a firm that furnished everything necessary for drilling except compressed air and water. In most instances the diamond-drill machine is clamped directly to a 3.5-inch column to reduce vibration. For drilling in floor pillars in open stopes, the drill was set on a demountable, sectionalized steel, frame with four legs carrying a 20-foot, 3.5-inch, extra-heavy pipe. "Both coring and noncoring bits were tried. In holes drilled with a cor- ing bit, the core was ground into sludge as the bit advanced so that it was unnecessary to delay drilling for pulling core. Data on tests with several types of bits are given as well as some oper- ating results. A direct comparison of costs between diamond drilling and percussion drilling was not available. The advantages of diamond drilling blast holes at mine A included: (1) Safer working conditions in open stopes. (2) The recovery of additional ore. (3) A reduction in the amount of stops development.

Dec 1, 1946

By L. C. IlsLey

Minin,g Qr col-cu.ttint till:I chines are 1?;\i9ng the _m9t wideiy .used de1sses ()f mining equipment.· These 1T:.i:1Chines ,.--re practicaily t-tl\·operc1_ted eiyher_by compressed .iir or by electric. ·motors. According to &.ta• compiled _ from the 122. issue COAL CATALOG\JE. OJMEINED WITH; OOAL "FIELD 'pf!:fC'TOTl1, bf 7,088. mnes from which reports were obttiined there -are 3895 mines that u.se coal-cutting eql;lipmen:ts,, 'f'hi report lists 20,031: r.ct:lchines, 17,&75 being operated by·elct:i.c.m<;>_tors··:r;id :the remtiinder by compressed i.r motors,· ,-. · ', .. . · .. ··, .. _ ,· .,, .. .. . . . . . : ; "'l t:: On tl.Ccou-nt .. of the wide· use of coc:11-cutting -.:i"cliine_- any Stat!;ls have issued regulationa as "to their operation dnd be to safety precautions that.should be observed J especially in gaseous mines.

Oct 1, 1922

By C. P. Bowie

"It is well known by all who are familiar with the oil industry in America that the oil pipe line is as fundamentally a part of this industry as the railroad is of most other American industries. The oil pipe line was first introduced about 56 years ago, and since that time has so demonstrated its superiority as a means of carrying crude oil froze the well to the refinery, that this method of transportation has largely superseded all others. This has made possible the building of refineries in or near the large consuming centers, rather than at the wells, which are usually remote from the centers of population.The pipes for conveying the oil are laid on the surface of the ground, or at a depth varying from 18 inches to 3 feet beneath the surface, and the main lines are generally eight inches in diameter. The oil is forced through the pipes by means of pumps operated either by steam or by internal combustion engines. The pump stations are located from 1 1/2 to 90 miles apart, varying with the condition of the country through which the pipe lines extend, and the viscosity of the oil to be handled.Some of the larger pipe-line systems and hundreds of miles in length. It is estimated by the U. S. Geological Survey that the total mileage of oil trunk lines in the United States today is approximately 34,000, and that the gathering systems, which are a fundamental part of the trunk systems, aggregate about 11,500 miles in length, making a total of 45,500 miles.Using those figures as a basis, some general conclusions as to the investment represented will be made. At the time most of the lines were constructed, the average cost per mile based on eight-inch pipe was about $6,500. The cost of the average pump station at that time varied from $130,000 to $250,000. The cost at the present time, on account of the increase in price of labor and materials, would be much in excess of these figures. The fixed investment in pipe lines is, therefore, very extensive. It corresponds closely with the actual cost of the property, and is estimated to be approximately $500,000,000."

Sep 1, 1920

By N. S. Dalal, X. Shi

"SUMMARYElectron spin resonance (ESR) measurements provide direct evidence for the involvement of the glutathionyl radical, as well as an isolable Cr(V)-glutathione intermediate in the Cr(VI) glutathione redox reactions. These results indicate a new mechanism for the reduction of Cr(VI) by glutathione in relationship to cellular environment and suggest that synergistic reactions of Cr(V) and GS· might be responsible for the (unexpected) increase in the Cr(VI)-induced DNA-strand breaks at high glutathione levels.INTRODUCTIONWhile the reduction of Cr(VI) by glutathione (GSH) is thought to be a critical' step in the pathogenesis of the Cr(VI)-exposure related carcinogenesis1- 4, the exact reduction mechanism is not yet understood. The following reaction steps have been suggested :(A) Initial step:Cr04 2- + GSH - GSCrOa - (1)(B) At high GSH levels:GSCroa- + GSH - Cr( IV) + GSSG (2)(C) At low GSH levels: GSC rO a - - Cr ( V ) + GS ·(3)Thus far, however, in these reactions, the GS· radical has eluded spectroscopic detection, while the evidence for the Cr(V) formation has been reported positives as well as negative2·. Her~ we present spin-trap ESR evidence for the formation of the GS· radical, and a definitive ESR detection of an isolable cr(V)-GSH intermediate in Cr(VI)-GSH reactions.MATERIALS. AND METHODSESR spectra were obtained at X-band (-9.7 GHz) using a Bruker ER200D ESR spectrometer. The magnetic field was calibrated with a self-tracking NMR Gaussmeter (Bruker, Model ER035M) and the microwave frequency was measured with a Hewlett-Packard (Model 5340A) frequency counter. The spin probes, a-(4-pyridyl-1-oxide) -N -tert-butylnitrone (4-POBN) and 5,5-dimethyl~1-pyrroline-1-ox1de (DMPO) were purchased from Aldrich, K2Cr201 from Fisher and used without further purification. All experiments were done at room temperature."

Jan 1, 1989

By J. W. Town

The Bureau of Mines studied the effects of reducing gas composition, tem-perature, and superficial gas velocity on the regeneration rate of alkalized alumina. Regeneration was assumed to follow the simple first order reaction for removal of sorbed S02: dµ/dt = -Kµ. An Arrhenius relationship can be plotted, which shows an activation energy of about 75 kcal/mole for simulated reformed propane. The general effects of the individual gases can be described as follows: (1) CO and H2 produced rates proportional to their con-centrations, up to about 5 percent for each; (2) addition of CO2 had no effects on the regeneration rate by CO; (3) the regeneration rate by H2 was lowered by the addition of H2O while the regeneration rate by CO was increased by 0 addition; (4) H2S showed a positive effect up to concentration levels of about 2 percent and then produced a rapid negative effect; (5) carbonyl sulfate (COS) increased the sulfur content; and (6) propane was as effective in regenerating the loaded pellets as was simulated reformed propane.

Jan 1, 1971

By J. Owens

Advanced materials development ranks as one of the most important high-tech industries of the future in the United States. Recent breakthroughs can be attributed to advanced computer technology, powerful mathematical models, and more precise analytical tools that enable scientists to examine and control properties of materials as never before. Discoveries now being made are providing many industries with opportunities to improve product lines, fabrication techniques, product reliability, and so forth. More¬over, industries, such as space, medicine, and defense, which require stringent: design and perfomance specifications in highly competitive world markets, increasingly demand these new materials. The definition of advanced materials used here is one that has been adopted by the U. S. Bureau of Mines: Those materials which have been developed over the past 30 years or so, and which are being developed at present, that exhibit greater strength, higher strength-density ratios, greater hardness, and/or one or more superior thermal, electrical, optical, or chemical properties, when compared with traditional materials.

Jan 1, 1991

By Jalna R. Zatko

Coal-clay waste slurries were dewatered in laboratory-and small-scale continuous tests by the Bureau of Mines using polyethylene oxide (PEO) as a flocculant. Dewatering from a nominal 7-wt-pct solids to over 50-wt-pct solids was accomplished using 0.5 lb of PEO per ton of feed in small-scale continuous tests. Parameters such as pH, initial solids content, and PEO concentrations were investigated. Water recovered from dewatering was reused as dilutant for PEO solutions.

Jan 1, 1982

By John C. Edwards

The Bureau of Mines has developed a time-dependent droplet vaporization model (in the absence of forced convection) that can be applied to the vaporization of liquid Halon 1301 droplets (vapor pressure at 300 K = 14 atm) sprayed from an extinguisher. It was found that rapid surface vaporization quickly lowers the droplets&apos; surface temperature very near to the boiling temperature, and the vaporization becomes diffusion controlled. Although the lifetime of the droplet is proportional to the square of the initial radius of the droplet, the elapsed time prior to complete droplet vaporization is not proportional to the square of the droplet radius, as an equilibrium model would indicate.

Jan 1, 1982

By Richard W. Lewis

Domestic production of greensand (glauconite) increased 15 percent in quantity and 13 percent in value compared with that of 1964. Since only two firms were in operation, statistics on production and sales for the year are not reported in order to avoid disclosure of individual company confidental data. The average annual production for the 5-year period 1961-65 was 4,306 tons valued at $200,200. The material was marketed for use as a soil conditioner and a water softener. An article of mineralogical interest was published concerning the New Zealand glauconites.2

Jan 1, 1966

By P. L. Woolf

An investigation was conducted to evaluate the use of a formcoke as the total fuel in the Bureau of Mines experimental blast furnace. The formcoke performed very satisfactorily, and comparisons made with a metallurgical coke showed that the performance with the formcoke was somewhat superior under the experimental conditions used.

Jan 1, 1966

By Uwe Kaulbars

Vibration measurements at the workplace are often complicated and expensive. The assessment of the risk in conformity with EC Directive 2002/44/EC “Vibration” (which lays down the minimum requirements of laws in Europe for occupational safety and health) can therefore be carried out on the basis of an estimate based on information from manufacturers as well as by measurement conforming to ISO 5349. The characteristic values (emission values) determined by manufacturers in laboratory conditions may deviate from the exposure values measured at source at the workplace. Equally, deviations may arise as a result of the delay in the changeover of test methods from the single axis of measurement to the total vibration value for the three axes of measurement conforming to ISO 20643. To prevent faulty estimates, the manufacturer’s information has to be corrected by a tool-related factor in accordance with CEN/TR 15350. By taking the example of masonry and stone working machines, the empirically determined tool-related correction factor is checked and confirmed. Methods Vibration measurements were carried out in accordance with ISO 5349 in practical application conditions on 10 selected typical eccentric and orbital sanders, concrete and disc grinders as well as on wall chasers and stone saws. Results The total vibration value obtained for the investigated tools rangedfrom ahv = 3.6 m/s² to ahv = 11.6 m/s². When the values from the practical measurements are compared with the manufacturer’s vibration values, the underestimation of the risk occurring in some cases can be largely compensated for by the tool-related factors conforming to CEN/TR 15350 (see Figure 1).

Jan 6, 2006

By G. R. Hopkins

A recently completed survey , made by the Bureau of Mines to determine the trend of fuel consumption at refineries in the United States , showed the following outstanding points : A decrease in the use of oil for fuel in 1927 of over 5,000,000 barrels as compared with 1926 ; a decrease in the use of coal of over : 1,000,000 short tons ; small increases in the use of both natural gas and refinery gas ; an increase in the use of petroleum coke . The decrease in fuel - oil consumption was approximately 2,000,000 barrels each in the Atlantic Coast , Texas , and Louisiana- Arkansas districts , with an increase of 1,000,000 barrels in the Indiana - Illinois district , or a net decrease of 5,000,000 barrels . The decrease in fuel- oil consumption by refineries in the Texas and Louisiana- Arkansas areas was offset largely by increased consumption of natural gas and refinery gas , whereas the increased consumption in the Indiana- Illinois region was more than offset by the decrease in coal consumption . The use of coal for fuel declined from 6,052,000 short tons in 1926 to 5,031,000 short tons in 1927. Practically all of this decrease was recorded in the Appalachian and Indiana- Illinois districts , which at the same time showed the largest percentage increase in the use of oil for fuel . It is probable , therefore , that although coal prices also fell off , a considerable quantity of oil replaced coal in this area in 1927. In addition , the group of refineries , which are by location more or less definitely committed to the use of coal for fuel , undoubtedly succeeded in saving a material amount of coal through the use of more efficient fueling methods . A total of 130,815,000,000 cubic feet of natural gas was consumed for fuel at refineries in 1927. This represents an increase of 8 per cent over the 1926 total . Nearly all of this increase resulted from the opening of a line from the Monroe field to Baton Rouge , La . Had this line not been opened , there would have been a decrease in the use of natural gas , as a number of districts , particularly the Rocky Mountain , reported decreases in its use . The use of refinery or still gases for fuel did not change materially during 1927 , there being a total of 52,807,000,000 cubic feet burned as compared with 52,077,000,000 cubic feet in 1926. Refinery gases are largely a product of cracking and , it was probably more than a coincidence that a few districts in which cracking slowed down in 1927 also reported less refinery gas used as fuel .

Jun 1, 1924

Work on this program was supervised by R. C. Streeter, Project Scientist, R. K. Young, Principal Investigator, and R. A Glenn, Project Director Technicians involved in the conduct of the experimental work were J R. Allender, D. R. Wolber, G. L Maclay, and A. C Rupert The assistance of Project Scientists C. T. Ford in the electrokinetic studies, and R. R. Care in the spectrographic analyses, is also acknowl- edged. The valued advice and guidance during the course of this program from R. D Hill, EPA Project Officer, and Dr. D R. Maneval, Director of Planning and Coal Research for the Department of Environmental Resources, Commonwealth of Pennsylvania, is sincerely appreciated.

Jan 1, 1971

1. PURPOSE The Temporary Face Support System (TFSS) consisting of beams, posts and carrying-emplacing equipment was developed to provide temporary supports between the working face and the permanent roof supports. 2. GENERAL DESCRIPTION The system consists of: ? A Beam And Post Carrier And Deployer (BAPCAD), a self-propelled machine that carries as well as emplaces the beam-and-post sets. ? Lightweight mechanically self-deploying posts designed to safely support a load of 10,000 pounds each. ? Lightweight constant strength beams (bars) capable of sustaining an approximate equally distributed load of 8500 pounds. Note. All referenced figures and drawings are found at the back of this manual.

Jan 1, 1980

By Eric R. Bauer

The magnitude and rate of advance of an inmine coal squeeze was deter-mined by measuring roof-to-floor convergence on a regular basis. A dial-gage tube extensometer was used to collect data. Using these measurements) Bureau of Mines employees drew contour maps and graphs to show the direction and rate of squeezing. Information on the rate of squeeze advance was used to determine whether steps should be taken to prevent roof and/or floor movement from closing an entire section of the mine and if alteration of mining plans was necessary to prevent further squeeze development. Data analysis revealed that the squeeze was decelerating; thus there was no need to strengthen support in the areas of the mine that were studied. Mining plans were altered, however, as a result of the findings of this investigation.

Jan 1, 1981