Search Documents

By D. G. Collins

As part of its effort to develop ways to maximize resource recovery, the Bureau of Mines investigated the extraction of vanadium from Western phosphate beneficiation tailings with H2S04 and/or H3P04. Dissolution of the vanadium was accomplished by digesting a mixture of acid and a 50-pet-solids, tailings-water slurry. In the most effective method investigated, vanadium and phosphorus were leached by digesting the slurry at a constant boiling temperature (1000-1100 C) in a stirred reactor. In batch tests, maximum vanadium dissolution was 95 pet. In continuous-circuit tests designed to further evaluate vanadium dissolution at con-stant boiling temperature in a continuously stirred reactor, vanadium dissolution ranged from 70 to 85 pet. An economic evaluation of the process demonstrated that H2S04 consumption is the major cost factor. Based on the value of the vanadium product with no allowance for a phos-phate product, the cost of producing the V205 is more than twice its value. The potential for profit would depend upon the value of the phosphate fertilizer produced from the impure H3P04 remaining after vanadium extraction.

Jan 1, 1985

By W. J. Johnson

This report presents the Phase I progress in the development of a Radar Coal Thickness Sensor (RCTS) being conducted by Boeing Aerospace and Electronics for the Bureau of Mines. A method is developed for measuring both the dielectric constant and depth of the coal shale interface using a modified UHF network analyzer and antennas in proximity to the surface of the coal. Both bistatic and monostatic systems, are compared. The algorithm technique uses synthetic range gating for clutter rejection and full polarimetric scattering matrix techniques to extract the dielectric constant and depth to sub-wavelength accuracies. Tests were run both in the lab and in a coal mine to build an error budget and demonstrate a validation of the model. The development of a prototype radar suitable for coal mine robotics is specified.

Jan 1, 1990

By R. R. Hornor, Geo. M. Hunt

The purpose of this paper is to point out some of the benefits and economies to be derived by the better selection , preparation, storage , preservation and utilization of mine timber , and to give some specific information on certain wood preservatives and processes suitable for mine timber preservation . The paper is based largely upon data obtained by actual experimentation and service tests conducted by the U. S. Forest Products Laboratory , Madison, Wisconsin, on wood preservation , covering a period of many years , and upon a field survey during the past summer by one of the mining engineers of the U. S. Bureau of Mines of some of the principal mining districts of Michigan , South Dakota , Montana , and Idaho , in which he made a general ' study of mine timber in metal mines , particular attention "being given to timber decay ; the conditions under which it takes place most actively ; the measures , if any , that are being used to combat it; and, finally, the advantages that might be anticipated in the use of chemically treated timber to prevent decay and thus prolong its life .

Feb 1, 1922

By N. H. Darton

In mining coal in the anthracite region of Pennsylvania the general custom has been to leave a large percentage of the coal in place as pillars to support the roof. Evidently any practice that involves partial waste of an important mineral resource is bound to be discarded. It is well recognized that one method of obviating probable waste is to fill the workings with cheap or worthless materials, a process extensively employed in the anthracite and some European mines. At present many of the collieries in the anthracite region of Pennsylvania are utilizing refuse from the old culm banks, which formerly were prominent features in the landscape, and are flushing the fine waste underground so that pillars may be reduced in size or removed. As a result the banks are now disappearing and soon will be gone. The fine culm from the breakers and rock from the mines will continue to be available, but the volume of these materials is insufficient to replace any considerable proportion of the coal removed. The next stage of progress suggested is the use of sand. Fortunately there are available large deposits of this material, much of which can be handled by dredges and pumps. This report is issued by the Bureau of Mines in the interest of safer and more efficient mining methods. I ts purpose is to describe the sand deposits in the northern anthracite coal field in Luzerne and Lackawanna Counties, Pa, Much of the information available is presented in the map, Plate I. Field studies, mostly preliminary, were made in the summer of 1911 to determine the distribution, amount, and character of the larger deposits. It was not thought desirable to make a detailed examination of the region because when the coal companies decide to utilize the sand their engineers will make precise surveys and drill test holes. In preparing the map the various coal companies were consulted; they contributed a large number of facts, especially as to the deposits in the buried valley of the Susquehanna between Pittston and Nan- ticoke, where nearly 1,000 test holes have been bored. The results of these borings were placed at the author's disposal, and have been utilized in drawing the boundaries given in the wide valley area and its extensions up Lackawanna River and NewportCreek. Wyoming Valley contains deposits of sand that are 100 feet thick over a wide area, 200 feet thick in places, and over 300 feet thick in the deep old channel south of Plymouth.

Jan 1, 1913

By Isaac A. Zlochower, Kenneth L. Cashdollar

The Pittsburgh Research Laboratory of the National Institute for Occupational Safety and Health (NIOSH) conducted a study of the explosibility of various metals and other elemental dusts, with a focus on the experimental explosion temperatures. The data are useful for understanding the basics of dust cloud combustion, as well as for evaluating explosion hazards in the minerals and metals processing industries. The dusts studied included boron, carbon, magnesium, aluminum, silicon, sulfur, titanium, chromium, iron, nickel, copper, zinc, niobium, molybdenum, tin, hafnium, tantalum, tungsten, and lead. The dusts were chosen to cover a wide range of physical properties-from the more volatile materials such as magnesium, aluminum, sulfur, and zinc to the highly "refractory" elements such as carbon, niobium, molybdenum, tantalum, and tungsten. These flammability studies were conducted in a 20-L chamber, using strong pyrotechnic ignitors. A unique multiwavelength infrared pyrometer was used to measure the temperatures. For the elemental dusts studied, all ignited and burned as air-dispersed dust clouds except for nickel, copper, molybdenum, and lead. The measured maximum explosion temperatures ranged from "-1550K for tin and tungsten powders to "-2800K for aluminum, magnesium, and titanium powders. The measured temperatures are compared to the calculated, adiabatic flame temperatures.

By R. S. Dean

The function of the Metallurgical Division is to conduct investigations relating to the treatment of mineral products from the state in which they are mined to the refined metal or other unfabricated product. These investigations include scientific and practical studies of ore dressing, covering the crushing and grinding of ores, separation by gravity, flotation. and magnetic methods; the hydrometallurgical treatment of ores, including cyanidation and amalgamation of the precious metals; the smelting and refining of copper, lead, and zinc, as well as the rare metals; and steel-melting practices from the raw ore to the finished steel. The object of this work is to conserve natural resources and eliminate waste by furnishing information on current methods of metallurgical practice. making fundamental studies of metallurgical processes, and developing new processes to the point of demonstrating their practicability. The Division is made up of sections devoted to the several phases of this work, each section being headed by an investigator capable of supervising his particular work. The work is carried on at the experiment stations and field offices or in the field, whichever seems best suited for the work in hand. The following, projects should be mentioned as particularly outstanding among those consummated successfully during the year: 1. Application of the type of chemicals known in the textile industry as wetting-out agents to flotation and agglomeration of ores, particulary soluble salts such as sodium and potassium chloride which must be treated in saturated brine. 2. Demonstration or a linear relation between surface and coercive force in magnetic minerals and Its application to magnetic separation and to the determination of grinding efficiencies and other metallurgical data which require surface determination at very fine sizes. 3. Pilot-plant demonstration of the practicability of the reduction of iron ore by natural gas and conversion of this direct iron into steel by direct melting and by forging and rolling before melting. The structure and properties of the iron so produced were studied in detail. This report covers the fiscal year July 1. 1934, to June 30, 1935.

Jan 1, 1936

By Jr. Herty

As the problem of inclusions in steel has become increasingly important, more and more attention has been paid to the source of the oxide inclusions in steel. In killed steels the oxide inclusions are traceable to the reaction of deoxidizers with the iron oxide dissolved in the steel during the refining period of the open-hearth heat. In a large class of steel known as "rimming steel" the action of the steel during solidification depends entirely on the gas evolved, and this evolution in turn is controlled by the amount of iron oxide in the liquid steel in the mold. It is therefore of great importance to be able to determine the amount of iron oxide dissolved in steel and to devise methods for the control of iron oxide in any class of steel. The object of the present investigation was to obtain a true value of the oxygen con-tent of liquid steel. If the steel has not been deoxidized, the greater percentage of the oxygen is present as iron oxide in solution.

Jan 1, 1932

By John R. Benham

In 1987, at the request of the Bureau of Land Management~ the U.S. Bureau of Mines studied 7,600 and 3,000 acres, respectively, of the Slocum Creek (OR-003-075) and Upper Leslie Gulch (OR-003-074) Wilderness Study Areas in order to evaluate their mineral resources. They are located in Malheur County, OR, about 25 mi northwest of Jordan Valley. Both areas have an occurrence of stone (welded tuff) covering about 3,000 acres which is suitable for construction purposes including road metal, ballast, and road fill. However, similiar deposits are more accessible and closer to markets.

Jan 1, 1988

By Aleksandar D. Bugarski

Three types of uncatalyzed diesel particulate filter (DPF) systems, three types of high-temperature disposable filter elements (DFEs), and one diesel oxidation catalytic converter (DOC) were evaluated in underground mine conditions for their effects on the concentrations and size distributions of diesel aerosols. Those effects were compared with the effects of a standard muffler. The experimental work was conducted directly in an underground environment using a unique diesel laboratory developed in an underground experimental mine. The DPF systems reduced total mass of aerosols in the mine air approximately 10-fold for light-load and 20-fold or more for high-load test conditions. The DFEs offered similar reductions in aerosol mass concentrations. The efficiency of the new DFEs significantly increased with accumulation of operating time and buildup of diesel particulate matter in the porous structure of the filter elements. A single laundering process did not exhibit substantial effects on performance of the filter element. The effectiveness of DPFs and DFEs in removing aerosols by number was strongly influenced by engine operating mode. The concentrations of nucleation mode aerosols in the mine air were found to be substantially higher for both DPFs and DFEs when the engine was operated at high-load modes than at low-load modes. The effects of the DOC on mass and number concentrations of aerosols in mine air were relatively minor when compared to those of the DPF and DFE systems.

Jan 1, 2009

By Maria I. De Rosa

The U. S. Bureau of Mines performed experiments to determine if the primary gas toxicities evolved during the early (~300° C) and later (~400° C) combustion stages of chlorinated polyester-reinforced mine ventilation ducts could be predicted by a smoke particle characteristic, for the development of a test parameter. The experiments were conducted in an approximately 20-L furnace, at 14-min durations at set furnace temperatures of 2500 and 1,000° C, with an airflow through the furnace of 10 L/min. The variables studied, as a function of time, were the hydrogen chloride (HCI), carbon monoxide (CO), carbon dioxide (C02), and oxygen (02) concentrations, furnace temperatures, the sample mass weight loss, the average smoke particle diameter (dg and average number and concentration (no), and the product of the average smoke particle diameter and concentration (dgno). Results show that the inverse of the smoke particle diameter-concentration product [(l/dgn0)], correlates directly and significantly with the primary gas toxicities evolved during both early (HCI) and later (CO) stages of combustion.

Jan 1, 1989

By Roy E. Peterson

The Bureau of Mines conducted an investigation to produce metallized pellets from domestic iron ore superconcentrates using lignite and subbituminous coal as reductants. Feed materials for the metallizing process consisted of commercially indurated iron oxide pellets and green pellets prepared from upgraded domestic concentrates with graphite or limestone as internal additives. Durability of the green pellets during metallization was investigated in tests conducted in a 7-inch-ID rotating drum furnace. Test results indicated that the major cause of pellet disintegration with the concentrates used was the tumbling action during reduction rather than forces generated within the pellets. In larger scale tests made in a 34-inch-ID by 35-foot-long kiln, the previously indurated pellets were metallized with lignite at 1,030° C with little disintegration. A 96-percent level of metallization was obtained in pellets having an average compressive strength of 420 lb. In subsequent, similar tests using green pellets containing graphite or limestone, pellet disintegration was more severe, with 10 to 40 percent of the feed being lost as dust. The surviving pellets had metallizations ranging from 88.3 to 94.4 percent and compressive strengths ranging from 60 to 68 lb.

Jan 1, 1976

By P. A. Bloom

Arsenic-containing flue dusts are currently being stockpiled by several nonferrous smelters in the United States. These stockpiles are a source of environmental concern since the dusts can be transported by wind and contain water-soluble arsenic. The stockpiles also represent an alternate source of metals. To provide a quality environment, the Bureau of Mines investigated a process to make environmentally acceptable the discard of arsenic obtained from the treatment of arsenical flue dust. The process includes (1) leaching arsenic from a lead smelter copper dross flue dust, (2) fixing arsenic as an insoluble compound, and (3) recovering other metal values. Overall results of acid-leaching tests on lead-smelter flue dusts showed that H2S04 dissolved 80 to 90 percent of the As, Zn, and Cd, and up to 86 percent of the In. Pb, Ag, and Au remain in the residue, which can be recycled to the smelter. Indium was recovered from the strong acid leach solution by solvent extraction; arsenic was fixed in a stable form by precipitation with Fe2(S04)3 and CaO or CaC03.

Jan 1, 1982

By R. L. Soderberg

Large open stopes mined by vertical crater retreat or sublevel s are sometimes backfilled with uncemented sand to support the stope walls and alleviate rock bursts. The failure of bulkheads in two different mines prompted a research project at the Bureau of Mines to prevent a recurrence of these failures. A series of laboratory tests with drains and sand filters was conducted to measure the bulk-head pressures when adequate drainage was maintained. Results showed that bulkhead pressure was reduced to near zero while drains were in operation, as compared to full hydrostatic pressure when drains were blocked or drainage was restricted. A relatively simple, free-draining bulkhead was shown to be adequate.

Jan 1, 1985

By J. G. Walters

This bulletin presents, in collected and tabluated form, Bureau of Mines and American Gas Association (EM-AGA) carbonization data pertaining to the chemical analysis of tars and the characterization of tars and light oils obtained from U.S. coals.

Jan 1, 1967

By R. G. Nelson

The mechanical properties of low-hafnium, arc-melted, Kroll-process zirconium are presented. The effect of temperature on the ultimate strength, yield strength, proportional limit, elongation, hardness, Young's modulus, electrical resistivity, and impact strength are shown, The effects of cold work and annealing on the tensile properties, bend radius, and formability, as determined by cupping tests, are also given, Tensile properties are compared, in part, to those obtained on earlier graphite-melted zirconium and on crystal-bar zirconium. INTRODUCTION The commercial production of high-purity, low-hafnium bearing zirconium has been achieved, and this metal is becoming available for industrial use. However, there is little published information regarding the physical and mechanical properties of this product; and, since there have been many improvements in the production and arc-melting techniques of zirconium in the past 3 years, it was considered advisable to present the properties of the vastly improved zirconium representative of current production.

Jan 1, 1954

By Michael F. Dunn

Since crushing of rock to a smaller size is an integral part of almost any mining and quarrying operation, a study was carried out to identify and develop improved techniques for alleviating a major cause of accidents and work stoppages arising when an oversize luck or boulder lodges in the throat of the crusher. The configurations and operations of various crusher types is described, sources of boulders in the mining operation, and a detailed review is made of mining, quarrying, and construction regulations for all states, Canada, and the Federal Government for applicable provisions. Representative mines were visited and other operations contacted for their boulder handling techniques where it was found that blasting techniques used included mudcapping, bombs, and blockholing, often done very crudely and inefficiently with poor practices and various mechanical systems were used such is hooks of, overhead cranes, impact hammers, and grapplers. Safety analyses of all methods pointed out the hazards associated with blasting in the open and the dangers of entering a crusher. Boulder blasting can be done in a safer fashion if a planned step-by-step procedure is followed, and inherently safer blasting products such as exploding bridge wire blasting caps and improved blockholing techniques. In general, though, the installation of a suitable mechanical system such as an impact breaker will prove safer and cost effective even in a smaller mine or quarry.

Jan 1, 1981

By T. A. Sullivan

High-purity vanadium metal was prepared by electrorefining commercial vanadium in a molten sodium bromide, potassium bromide, and vanadium dibromide electrolyte. Variables investigated were operating temperature, current densities, electrolyte composition, and condition of the anode. The purity of the refined metal was in the range of 99.95 percent vana-dium. Iron and oxygen in the 50- to 250-ppm range were the only major impurities. Metal with hardness numbers of 50 to 60 in the Rockwell F scale was prepared from feed material with a Rockwell B hardness of 90. The arc-melted metal was highly ductile and could be cold-worked into sheet or foil.

Jan 1, 1965

By J. E. Miller

Primary standard gas mixtures were developed for more accurate calibration of analytical instruments at the Bureau of Mines Helium Research Center and for calibration of analytical instruments used in the helium conservation program. A 10-kg-capacity balance is used to weigh a 4-kg metal cylinder filled to high pressure (1,800 psi maximum) with the component gases of the desired mixture. At 1,800 psi, a cylinder contains about 60 g of helium, or 420 g of nitrogen. An accuracy of ±0.05 mole-percent or better is claimed for each component in the mixtures.

Jan 1, 1965

By J. W. Paul

This paper deals with the second phase of an extensive research on coal-mine ventilation factors. A comprehensive report of the entire work is in course of preparation, but abstracts of the various chapters are being prepared in order to make the results public as rapidly as possible. Part 1 dealt with the resistance of unobstructed entries and was issued as Serial 2621 of the Bureau of Mines, in July 1924. Description of tests. After the resistance of an unobstructed entry to flow of air had been determined by tests in the Experiment mine, mine cars were; run into the test section in various arrangements and the increase in resistance was determined. The cars used were of the wooden type with loose end gate, and would hold about one ton of coal, level full. They were 7 feet long. 4 feet 2 inches wide above the wheels, 3 feet high, and had a cross-sectional area of approximately 10 square feet. The average area of the entry was about 57 square feet, the ratio of unobstructed to total area being about 17.6 per cent. The track gage was 42 inches and the wheel-base 20 inches.

Jan 1, 1924

By H. G. Iverson

An investigation was conducted on the conditions affecting the precipitation of aluminum by autoclaving synthetic solutions containing Na2SO4, Al2(SO4)3, H2SO4, and H2O. Virtually all of the alumina could be precipitated as natroalunite (NaAl3(SO4)2 (OH)6). This product could be readily filtered and dried. Results are reported in terms of alumina precipitated in this compound and not in terms of alumina itself. Solutions of ~ 0.30, ~ 0.60, and ~ 0.80 mole/liter A1203 and various concentrations of H2SO4 and Na2S04 were investigated. The optimum time and temperature for autoclaving were 20 to 30 minutes at 200° C. The highest yields of natroalunite were obtained from solutions containing little H2SO4 and ~ 2 moles Na2SO4 per mole A1202. Acid in quantities of 0.3 to 0.5 mole/mole of alumina in solution depressed the yield to 90 percent or less. In differential thermal analysis, at 1,000° C the natroalunite precipitate decomposed without melting to yield SO, and SO2 gases, a solid composed of Na2SO4, and gamma and alpha Al203. Continued heating to 1,200° C produced No SO, and alpha A1303. Water-leaching of this product removed the Na2S04 and left a final residue of alpha A1203.

Jan 1, 1968