Search Documents

By W. S. Landers

This report presents a detailed study of low temperature, entrained-bed carbonization of an Australian coking coal. The coal studied was high-volatile B bituminous from the Foybrook mine, an open-cut operation in the Liddell seam, New South Wales, Australia. Carbonization was conducted in an 8-inch diameter, continuous vertical reactor at several temperatures from 960° to 1,300° F. It was demonstrated that this bituminous coal can be carbonized within this temperature range to produce tar and a nonagglomerated char, without prior oxidation or char recirculation. Carbonization rates from 138 to 287 lb/hr (as-carbonized basis) were investigated. It was found that the carbonization temperature and the air-to-coal ratio must exceed minimum values to insure continuous operation. At the higher air-to-coal ratios employed, all or most of the carbonization heat was provided by internal combustion with air in the reactor. At the lower air-to-coa1 ratios, part of the heat for carbonization was supplied externally. On the moisture-and ash-free basis, the yield of tar plus light oil ranged from about 26 to 44 gallons per ton, and the char yield ranged from approximately 1,160 to 1,370 pounds per ton. The heat in the gas ranged from about 900 to 3,000 Btu/lb of moisture-and ash-free coal. Carbonization product yields correlated well with air-to-coal ratio and carbonization temperatures. The volatile matter in the char was found to be temperature dependent. At 1,300° F carbonization, the volatile matter in the char was 8.7 percent (dry basis), whereas at 9600 F carbonization, the residual volatile matter was about 16 to 18 percent (dry basis).

Jan 1, 1965

By John D. Foulkes

An investigation is made into whether commercially available equipment can be used to engineer effective emergency warning systems for underground coal mines. Discussions with members of the Bureau and the Mining Enforcement and Safety Administration established that the preferred system should operate over the existing Pager Phone twisted pair, and broadcast an audio alarm. Applicable equipments such as voice band tone signaling equipment, alarm sounding equipment, mine telephones and complete alarm systems from over thirty manufacturers are listed. Factors affecting the range over which an alarm could be detected in representative mine situations were studied. These included (a) the subjective masking effects of typical background noise found in mines, such as that due to continuous miners (b) the attenuation of sound in mines (using both a theoretical and experimental results) and (c) the attention-getting qualities of different sound for miners. Audio alarm systems meeting the requirements can be installed and representative systems are described.

Jan 1, 1977

By C. M. K. Boldt

The Bureau of Mines surveyed waste disposal sites at 18 metal and non-metal mines and conducted laboratory and full-scale field tests to de-termine the effects of tailings deposition techniques on physical properties of tailings pond beaches. Survey data included measurements of beach slopes, descriptions of deposition techniques, and measurements of beach physical properties taken at various distances from the point of discharge. Laboratory tests involved depositing two types of tailings, each with different grain-size distributions, into a settling trough and determining the resultant physical properties of settled materials along the length of the beach. Side confinement and the closeness of the water pool to the point of deposition caused the laboratory results to be inconclusive. Full-scale field deposition tests conducted at the tailings pond of a cooperating mine showed that there were similarities in relationships between exit velocities of tailings slurry and physical properties of the settled tailings on the beach.

Jan 1, 1988

By R. R. Sayers

Under compuision of the present urgency to implement the President's promise to make the United States the arsenal for the democracies there is a tendency to demand a relaxation of restrictions on hours of labor and to speed up all industrial processes. The pressure is the more insistent with growing realization of the importance of the time factor in the success- ful prosecution of the war effort and the lack of skilled workers due to (2) operation of the draft, lack of an apprentice system in industry, and loss of skill by workers unemployed for long periods during the depression. With "total" war such as it is today the probabilities are that everyone will be required to exert greater effort (in many instances in activities to which they are unaccustomed) for longer periods than ever before has been necessary. The question arises, "What will be the aftereffects as well as the immediate effects on health, safety, and efficiency?" A review of the literature leaves the impression that this question has not been an- swered completely, especially as regards the ultimate effects. Mechanization, speeding up of industrial processes, mass produc- tion, and the small industrial concerns present many problems to indus- trial medicine. Does the tendency to expect the worker to produce at full speed all the time he is on the job decrease the effectiveness of the shorter working hours and cause undue fatigue, loss of efficiency, and increased accident proneness? The answer is important as this condition is likely to be intensified by the exigencies of the present emergency. According to Viteles (1)3, The increased tension under such conditions of work appears to offset the savings in muscular force made pos- sible by the machine. The tension, the speed, the subject- tion to specialization of work and a rhythm uncontrolled by the individual promote fatigue, characterized by a "decrease in the power to work, a decrease in pleasure taken in work, and a decrease in the enjoyment of the hours spent away from work."' The crowding of workers in temporary structures without proper provision for comfort and health may add greatly to the general fatigue factors already present in many industrial establishments. In 1932 Lockhart (2) stated that the production and maintenance of a healthy, satisfied industrial population is the most urgent necessity, involving problems so serious as to constitute a national task too great economically to be relegated to industrial concerns. If this was true in 1932, it must be doubly so today.

Jun 1, 1942

By Frederick W. Lee

List of contributing editors of Geophysical Abstracts:

Sep 1, 1932

By John Ward Smith

Variations in specific gravity of oil retorted from oil shales of the Eocene Green River Formation in northwestern Colorado were evaluated statistically, demonstrating that these variations are very strongly associated with stratigraphic position and less strongly but still significantly associated with geographic location. Specific gravity of oil retorted from these oil shales apparently varies with the carboxyl group content of the oil shale's organic matter. Higher temperatures accompanying increasing depth of burial probably progressively decarboxylated oil shale's organic matter producing the decrease of oil specific gravity associated with deeper stratigraphic position. The geographically associated oil-gravity variations were probably produced by regional variation in the original thickness of late Cenozoic extrusive rocks once overlying the Green River Formation.

Jan 1, 1966

By T. M. Barczak

The term "resultant load vector" is defined as the representation of the forces applied to a longwall roof support element by strata activity through a single, quantifiable measure of support resistance. The relatively complex kinematics of the shield structure prohibits determination of support resistance simply from the summation of leg forces. In the research reported in this Bureau of Mines study, the mechanics of the shield structure were evaluated, and a technique was developed whereby the resultant shield loading could be determined by instrumenting supports with pressure transducers and strain gauges to measure leg, canopy capsule, and lemniscate link forces. This technique has been laboratory tested in the Bureau's Mine Roof Simulator. Functional relationships among variables were assessed, and confidence intervals were established for prediction of the resultant load vector parameters. Resultant load measurements were taken on five instrumented shields on an active longwall face in Colorado. Results were analyzed and found to be consistent with shield mechanics and anticipated roof behavior. Benefits to be derived from this research, future efforts, and long-range goals are discussed.

Jan 1, 1986

By Lawrence G. Houk

Lithium is the lightest of all metals, but as it deteriorates rapidly in air it has no structural applications. Alloys of lithium that will float upon water can be made with other light metals, but these ultralight alloys are not useful in aircraft production or elsewhere at present. Alone or alloyed with alkaline earth meals, lithium acts as reining agent on molten metals, and as a minor constituent with other metals it imparts characteristic properties to the allay. Lithium compounds have somewhat wider application in commerce than either the metal or the alloys. They are used in the glass, ceramic, chemical, and air-conditioning industries and less extensively in the optical, pharmaceutical, electrical, and textile industries. The United States is the leading producer anti consumer of lithium ores and compounds and apparently has the largest known ore reserves. The value of lithium ores and primary chemical byproducts produced is relatively small, yet the lithium chemical industry yields products worth hundreds of thousands of dollars each year, owing partly to the high degree of purity demanded by the trade for most finished products and to the low combining weight of lithium. Fortunately, the low-grade ores can now be concentrated economically, and this fact, together with our extensive reserves, assures adequate supplies to meet any reasonable increase in demand. Lithium is listed as essential by both the American and British war agencies, and its military importance may be greatly enhanced.

Jan 1, 1942

By Robert L. Lappi

This report covers the final phase of a project demonstrating the economic efficiency of cross-ridge mountaintop coal mining. A demonstration mine was established at Big Wheel Gap in northeastern Tennessee. Not only was cross-ridge mining feasible for the selected site, but parallel cut methods could not be used due to a deficit in available spoil storage. Cross-ridge mining permitted coal extraction at a cost almost identical with costs simulated by computer projections using mathematical optimization techniques. No unexpected environmental problems were encountered. Volume I is accompanied by Volume II which describes the MATHMINE Mine Simulation System, software used to support the mining demonstration.

Jan 1, 1984

By J. Frederick Stampfer

Current certification testing of self-contained breathing apparatus includes tests with human subjects wearing the apparatus while exercising. During these tests, certain apparatus variables are measured during rest periods. Because of concerns that the present tests may not accurately simulate the stresses to which an apparatus is subjected in the field, the Bureau of Mines proposed new human subject tests. It was also felt that different measurement techniques would supply more reliable data on the apparatus response to these stresses. The Los Alamos National Laboratory was asked by the Bureau to evaluate the proposed tests and monitoring techniques. The major conclusions derived during this study are these: (1) The proposed tests are not too physically demanding. (2) As long as human test subjects are used, a minimum subject weight should be required for certification tests. (3) Important apparatus variables are the breathing resistance, temperature, and carbon dioxide and oxygen concentrations of the inhaled gas. (4) Continuous monitoring should be used, rather than monitoring only during rest periods. (5) New pass/fail criteria based on realistic estimates of the user's physiological requirements, as tempered by present and future engineering limitations, are needed. (6) When available, breathing machines, rather than human subjects, should be used for most certification testing. (7) A more realistic ergonomics test than that proposed is needed. (8) A gas leak test for the system and a facepiece leakage test are also needed.

Jan 1, 1983

By G. B. Gait

This report is the third in a series concerning the Bureau of Mines program for microfilming maps of abandoned mines in the Pennsylvania anthracite region; a catalog of the microfilmed maps of mines in the Lackawanna Basin of tile Northern anthracite field is presented. Previous reports IC 8274, published in 1965, and IC 8379, published in 1968, were catalogs of microfilmed maps of mines in the Eastern Middle anthracite field and Wyoming Basin, Northern anthracite field, respectively , Additional catalogs will be published as the microfilming of significant mining areas is completed.

Jan 1, 1970

By E. H. Denny

This paper discusses accident experience and costs in 150 Colorado coal mines for the 5 years 1929-33; these mines produced 62 percent of Colorado's coal tonnage during this period. This and similar studies by the United states Bureau of Mines in other States (listed in the appendix to this report) make available comparable information on mine-accident costs and bring out clearly the importance of accident reduction from the humanitarian as well as from the economic standpoint. Compensation insurance costs constitute a considerable part of the cost of coal output. The tendency toward greater liberalization of workmen's compensation laws and increased benefits thereunder may mitigate to some extent the seriousness of an accident to a worker and his dependents, but no compensation is paid ultimately, not by an insurance fund but by the mine operator and the general public, which includes the miner. The one really effective method of reducing compensation costs is to reduce the number and severity of accidents.

Jan 1, 1935

By Donald W. Mitchell, John Nagy, Edwin M. Murphy

"Investigations in the Federal Bureau of Mines Experimental coal mine near Pittsburgh, Pa., have shown that high-expansion foam containing at least 0.2 ounce of water per cubic foot of volume is effective in controlling exper-imental underground coal, oil, or wood fires. Some of the fires were extinguished, but more of the coal and wood fires were brought under enough control to permit direct attack with water or other extinguishing agent or loading the hot material into cars. The largest controlled experimental fire, which burned about 5 hours before attack, was in a coalbed 5 feet wide, 10 inches thick, and 100 feet long. The greatest distance foam was transported to control a fire was 1,010 feet.An incipient fire should be attacked promptly with water, rock dust, or other approved and readily available extinguishing agents. Where heat, roof falls, and smoke prevent direct approach, the more involved procedure of using foam may be advantageous. The effectiveness of the foam in controlling a deep coated fire of considerable extent H,vet to be proved by actual trials in aSome hydrogen, carbon monoxide, and methane gases are generated when a fire is attacked with foam. Calculations showed that in experimental fire tests an explosive mixture could form; however, this would occur only within a narrow range of combustible gas-air mixtures not likely to be found in practice. The principal explosion hazards are due to generation of gases by the foam, localized build-up of normally liberated methane, and volatiles liberated by the coal during heating. The quantity of combustible gases generated by the action of the foam on the fire is about the same as that when an equivalent amount of water is applied."

Mar 1, 1960

By Edward Roberts

This is a progress report of an investigation by personnel of the Bureau of Mines from June to September 1951 to introduce preservative chemicals into growing timber. It also describes in detail the impregnation process, known as the collar method, developed by the United States Department of Agriculture2/ Twenty-eight trees were treated by this method, and a complete record was kept of each individual tree and of each timber cut from it. These timbers have been placed in a coal mine, and their tendency to decay is compared to that of adjacent untreated sets. Although several years will be required before final conclusions can be drawn, this report explains the appearance and encouraging results of the treated timber to date. Also included are some comparative costs of untreated timber, treated timber by the commercial pressure method, and treated timber by the collar method. INTRODUCTION In the hope of increasing the useful life of cut timber, experiments to impregnate growing trees with wood-preservative chemicals by utilizing the natural flow of sap have been carried on for centuries. None of the various methods used in these experiments has ever gained any widespread use because they have been commercially impractical.

Jan 1, 1953

By W. E. Wallace, V. Castranova, F. Saus, D. Bates, C. A. Hill, V. Vallyathan, M. J. Keane

"Two in vitro systems are being developed to model initial stages in the interaction of respired dusts with the acinar region of the lung. Incubation of quartz and kaolin with dipalmitoyl glycerophosphorylcholine, a major component of pulmonary surfactant, suppresses the prompt C)1otoxicity of both dusts as measured by in vitro enzyme release from pulmonary macrophages or assay by erythrocyte hemolysis. Additional data is presented to quantitate the detoxification of quartz and kaolin by dipalmitoyl lecithin. Subsequent incubation of lecithin treated dusts with phospholipase enzymes results in partial to complete restoration of the assayed cytotoxic potentials, dependent on the lipase activity applied, the incubation time, and the mineral. Restored cytotoxic potential is due to removal of the prophylactic lecithin surface coating and/or due to residual lysolecithin which is produced by the partial enzymatic digestion of lecithin. Data is presented on the contribution of each mechanism to the restored toxicity. Again, this is dependent on the mineral used, the lipase activity applied, and digestion time. Additionally, a system is under development to challenge pulmonary macrophages in culture with native and surfactant treated dusts. A preliminary test of the dipalmitoyl lecithin - quartz rabbit pulmonary macrophage system is presented to illustrate the method.IntroductionRespirable quartz dust exposure is known to cause librotic lung disease; respirable clay dust exposure is less likely to do so as indicated by epidemiologic data on occupational exposures and by animal model studiesP·7) The hypothesis that damage to pulmonary macrophages in the acinar region of the lung by respired dusts is an early event in the disease process requires consideration because kaolin clay and quartz dusts are comparably cytotoxic to pulmonary macrophages in vitro.(3•9)"

Mar 1, 1989

By Walter R. Storms

"INTRODUCTION Geological examination of the Iron Mountain beryllium deposits was begun by a field part 3/ of the Federal Geological Survey in May 1942. Later in that month the occurrence was examined by the author and C. H. Johnson, of the Bureau of Mines, and a preliminary exploratory program was outlined. Trenching and sampling began about June 15 and were completed in July 1942. A large tonnage of beryllium-bearing material was indicate by this preliminary survey, so that additional funds wore allotted for further trenching and sampling, underground exploratory work, and diamond drilling. This later program was initiated in July 1942 and was completed in May 1943. 4/ACKNOWLEDGEMENTSIn its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilisation of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metallurgical Branch, R.G, Knickerbocker, chief, analyzes samples and performs beneficiation tests."

Mar 1, 1947

By Thomas J. Albin

This U.S. Bureau of Mines report identifies potential causes of slip-and-fall accidents occurring during surface mine equipment maintenance and describes the relative roles of direct worker behavior and machine design. The relative roles of human behavior and machine design in the causation of slip-and-fall accidents were determined through analysis of accident records, observations of maintenance worker behavior, and evaluation of mine machinery. From these data, relative risk ratios were calculated. Behavior had a relative risk ratio of 1.5; machine design, specifically access systems design, had a relative risk ratio of 2.2. Of the access systems, ladders had the highest relative risk ratio, 7.0. This study suggests that accident intervention would be most profitably made in improving the design of systems used to access maintenance worker areas of mining equipment.

Jan 1, 1990

By Lloyd Williams, James R. Boyle

The mining methods and practices used at the Young zinc mine, American Zinc Co. of Tennessee, have resulted in a low-cost, high-yield operation. Zinc ore (sphalerite) occurs in limes tone- dolomi te beds of the Kingsport Formation and is mined by modified room and pillar method. Utilizing trackless mining equipment which incorporates a high degree of flexibility, this operation has had a steady increase in productivity.

Nov 1, 1964

By K. E. Tame

The Bureau of Mines is studying possible modifications in conventional ore-processing methods that will confine and permit controlled disposal of radioactive liquid wastes. Stream and ground water pollution from radio-active nuclides, principally radium 226 and thorium 230, in liquid wastes from uranium mills can be minimized by reusing the waste solution within the mill. Such reuse of waste solution in an acid leach-resin-in-pulp flowsheet was investigated in the laboratory. The process consists of acid leaching for dissolution of the uranium, sand-slime separation and countercurrent decantation washing for recovery of a pregnant slime slurry, and the use of ion-exchange resin for recovery of uranium from the slurry. Reuse of clarified barren effluent for washing in the simulated mill circuit was carried through 55 cycles. Dissolution of uranium from the ore averaged 97.5 percent. Washing efficiency of 99.9 percent was attained when using 4.35 volume tons4 of combined barren effluent and makeup water per ton of ore. Absorption of uranium from the pregnant slime slurry by an ion-exchange resin averaged over 99.9 percent.

Jan 1, 1962

By J. L. Eakin

A method was developed by the Bureau of Mines in the laboratory and in the field to relieve capillary waterblocks in gas wells. Impaired gas permeability was improved by this inexpensive chemical treatment which lowers the surface tension of the water held in the capillaries of the formation. Effectiveness of the alcohol-surfactant treatment was tested with a variety of chemicals and with sandstone cores cut from rocks having relatively low permeability. Field tests on 20 gas-producing and storage wells demonstrated the effectiveness and limitations of the method. The productive capacity of some wells was doubled by the treatment. The final test was evaluated by the neutron logging technique for measuring changes in apparent liquid saturation. Maximum apparent liquid saturation was reduced by 52 percent; gas production rate increased from 2.3 to 3.5 MMcfd (million cubic feet per day).

Jan 1, 1965