Search Documents

By Ferdinand Roehlich

An evaluation of the use of manually activated, installed,. dry chemical fire protection systems on underground metal and nonmetal mine vehicles is described. In addition, an assessment of the possible health risks posed by the dry chemical extinguishing agents used in such systems is provided. Work involved installation of fire protection hardware on an operating piece of underground metal/nonmetal mine equipment and, via actual fire tests, a determination of the effectiveness of the hardware in extinguishing on-vehicle fires. Two fire protection systems were installed on a Caterpillar 988 front-end loader in St. Joe Mineral's Fletcher mine, near Viburnum, Mo. Both a fully pressurized Safety First CM-20 and a nonpressurized cartridge actuated Ansul A-101 were installed for comparative purposes. Both systems operated satisfactorily during an 8-month endurance trial period which preceded the actual fire tests. Each system was able to extinguish an 18" x 4" class B test fire placed in the engine area of the machine. The health hazards analysis of dry chemical powder consisted of a detailed search of published literature relating to these multipurpose agents. This data was verified via a controlled laboratory analysis of two monoammonium phosphate based powders (Safety First Unikem and Ansul Forey) and an analysis of air samples collected at various locations on the test vehicle during the fire tests. Although the powder was found to be nontoxic, two potentially dangerous thermal decomposition products were identified--ammonia and phosphoric acid. However, later analysis indicated that an operator would not be exposed to dangerous concentrations of either compound if he were to remain outside of the powder cloud. A "Selection and Use Manual for Manually Activated, Fixed Fire Suppression Systems on Underground Metal and Nonmetal Mining Equipment" was prepared both as an, appendix to the report and for distribution under separate cover.

Jan 1, 1977

By Merwin H. Howes

In constructing the NORAD Combat Operations Center, controlled blasting techniques were employed to achieve smooth walls and to avoid shattering the rock beyond excavation lines. Extraordinary measures were taken to stabilize the rock to permanently preserve the openings. Rock stabilization was accomplished by means of reinforced concrete and gunite linings, rock boltings, installation of chain-link fabric, and epoxy resin and cement grouting. A particular zone of weakness at B vital location was supported by exceptionally thick reinforced concrete lining, rock bolts, and cement grout.

Jan 1, 1966

By J. B. Zadra

Much has been published by various investigators on the use of activated carbon for adsorbing precious metals from cyanide solution and pulp. For the benefit of the reader, a list of these earlier publications appears at the end of this report. The present paper deals only with a process for extracting gold from gold-laden carbon and re-use of the de-adsorbed carbon. At the Getchell mine, Redhouse, Nev., experiments have been in progress for several years concerning the use of activated carbon to adsorb gold from their slime circuit pulp. The experimental work has been successful. Their practice has been to ship the gold-laden carbon to a smelter for treatment, which meant the total loss of the carbon in addition to smelter and freight, charges, all of which proved costly and wasteful.

Jan 1, 1950

By F. M. Jenkins

Longwall mining systems are used to mine approximately 50 pet of the world's total underground coal production. Single entries are the predominant method of longwall development in Europe and Asia, where mining conditions are more severe than those encountered in the United States. During the 1970's and early 1980's, the U.S. Bureau of Mines and the U.S. mining industry invested nearly $20 million in single-entry and related research. This report reviews the accomplishments of single-entry research in the United States and describes two U.S. single-entry field projects: the Sunnyside single-entry project in central Utah and the tunnel-boring project in northern West Virginia. Also discussed are a single-entry study conducted by North American Mining Consultants (NAMCO) and a single-entry design study conducted by Ketron, Inc. This Bureau report compares the resulting technology with European counterparts to further assess the utility and efficiency of U.S. systems.

Jan 1, 1990

By William K. Cunningham

The investigation described in this report was begun as part of the Bureau of Mines progress to develop acid processes for the extraction of alumina from low-grade bauxite and. clays. A domestic shortage of high-grade bauxite sui table for treatment by the Bayer process became acute as a result of' World War II; an intensive search for a practical acid process using lower-grade alumina-bearing raw materials was therefore warranted. The laboratory development was described in a preceding Bureau of Mines publication wherein the basic theory for the design and erection of a pilot plant maybe found. A 2-ton-per-day continuous pilot plant was constructed and successfully operated at College Park, Md., which demonstrated conclusively the chemical and mechanical feasibility of a solvent purification process for aluminum sulfate. The estimated production cost of $38.64 indicates that under present market conditions the process would not be economically feasible.

Jan 1, 1948

By Arno C. Fieldner, J. W. Paul, WALTER A. SELVIG

Many mine samples of coal are analyzed each year in the laboratories of the Bureau of Mines. The analyses are made in connection with investigations relating to fuels belonging to or for the use of the United States Government, the causes of accidents in coal mines, the geologic relations of coal beds, and the quality and the value of the coal and lignite in the public lands. The systematic collection and analysis of such samples in connection with fuel investigations was begun in 1904 at the Government fuel-testing plant at the Louisiana Purchase Exposition. and was under the direction of the United States Geological Survey for six years. Descriptions of the coal samples collected between the beginning of this work, July 1, 1904, and the transfer of the fuel-testing and mine-accident investigations to the Bureau of Mines,July 1, 1910, were compiled and published in Bureau of Mines Bulletin 22.' Descriptions and analyses of samples collected during the fiscal years 1911 to 1913 were published in Bureau of Mines Bulletin 85.2 Descriptions and analyses of samples collected during the fiscal years 1913 to 1916 were published in Bureau of Mines Bulletin 123.3 The present bulletin presents analyses and descriptions of samples collected during the fiscal years 1916 to 1919. In order that the material in this bulletin may be used to supplement that presented in Bulletins 22, 85, and ,123, the same plan of geographical classi- fication has been followed, the analyses and descriptions of the samples being grouped in alphabetical order according to the State, county, and town near which the mines or prospects sampled are situated.

Jan 1, 1922

By M. D. Marshall

A remote heat-activated stench gas/tracer gas mine alarm system was developed to reduce the time between fire detection and personnel notification. The stench gas/ tracer gas system contains ethyl mercaptan for personnel warning and a fluorocarbon for tracer gas detection by instrumentation. A system was also developed which can be interfaced with multiplex mine phones. In-mine tests were conducted and several systems are presently installed in a hard rock mine.

Jan 1, 1983

By R. S. Rosso

A program to investigate the effects of hardened washers on the uniformity of roof bolt tension and the resulting ground control in an underground mine was carried out. The complete roof bolt installation and roof bolt loads, mine convergence, and bed separation were monitored for a period of five months. The results show no evidence to support or refute the theory that mechanical roof bolts offer better support when they are installed with a high uniformity of tension. Also shown is the fact that if the bolts are installed with a maximum deviation from the mean torque of ±15% the addition of hardened washers significantly improved the uniformity of the installed tensions in the roof bolts.

Jan 1, 1977

By Lloyd H. Banning

Crucible-smelting tests at the Northwest. Electrodevelopment Laboratory and a pilot-plant test on electric smelting of western phosphate rock for the Westvaco Chlorine Products by the Tennessee Valley Authority indicated that the small vanadium content of the rock is concentrated in the ferrophosphorus by-product of Phosphorus smelting. This research is concerned' mainly with recovering vanadium and phosphorus froth the ferrophosphorus produced from western phosphate rock. Exploratory tests were made of several methods of treating vanadiferous ferrophosphorus. Attempts to separate vanadium as a carbide dross by saturating molten ferrophosphorus with carbon were unsuccessful. Volatilization of phosphorus from ferrophosphorus was accomplished to some extent, both with and without addition of sulfur in several forms, but elimination of phosphorus was not complete. Brief testing in a small experimental converter on oxidation of vanadium and phosphorus; into a slag by blowing with air showed promise. A method that comprised fusing vanadiferous ferrophosphorus mixed with soda ash under oxidizing conditions gave encouraging results and was tested beyond the preliminary stage. A slag product of the fusion contained most of the phosphorus and vanadium as water-soluble sodium phosphate and. virtually water-insoluble sodium vanadate. After leaching the sodium phosphate froth the slag, the leach residue was reroasted with soda ash and salt. This roasted product was leached again with water to extract the vanadium.

Jan 1, 1951

By L. A. Neumeier

A refinement of the tungsten-cobalt phase diagram is presented for compositions to 85 at. pct cobalt and for temperatures to the solidus. Preparation of alloys by powder metallurgy methods is described, and the results of studies made by a combination of techniques involving microscopy, X-ray diffraction, thermal analysis, and dilatometry are discussed. The existence of u-W6Co7 is confirmed (rhombohedral D85 structure). The W6Co7 phase forms periectically at 1,685'115° C by reaction of liquid with primary W; the peritectic melt is at 71 at. pct cobalt. The homogeneity range of u-W6Co7 extends to both sides of the ideal stoichiometric ratio, through a compositional range of about 5 at. pct. The compositional limits for u-W6Co7 vary slightly below 1,471°±5° C, the temperature of the eutectic reaction forming u-W6Co7 plus a. The eutectic composition is at 79 at, pct cobalt. The existence of WCo3 is confirmed (hexagonal D019 structure). WCo3 forms peritectoidally at 1,093°±5° C by reaction between a and u-W6Co7 and exists over a narrow homogeneity range of 0.5 to 0.6 at. pct. The solid solubility of cobalt in tungsten is low (maximum 0,9 at, pct cobalt) and results in contraction of the tungsten lattice. Tungsten is extensively soluble in a-Co at higher temperatures; the a-Co lattice is expanded by the presence of tungsten in solid solution. There was no indication of the formation of a o-phase nor of any intermediate phases other than WeCo7 and WCo3. The WeCo7 and WCo3 phases are compared with similar phases in other systems.

Jan 1, 1967

By C. M. Harrer

Reconnaissance investigations were made of 129 iron occurrences in Arizona to determine their extent, attitude, and potential; character samples were analyzed to determine their quality and impurities; and pioneer metallurgical investigations were made on character samples to present their metallurgical problems. Some factors influencing past and potential western iron markets are discussed. The location, features, qualities, extent, and potential of iron occurrences and some associative resources--limestone and dolomite, coal, petroleum and natural gas, power, and water are discussed. The most abundant iron minerals are magnetite and hematite. The higher grade deposits are extensive contact-metamorphic or pyrometasomatic replacements of calcareous Paleozoic to Proterozoic rocks associated with intrusives. Large low-grade deposits of great potential are present as Precambrian taconite, semitaconite-, and jaspilite-like iron formations of magnetite-hematite. Iron occurs also as low-grade concentrations of magnetite in extensive alluvial deposits. Nonferrous metallurgical slags, nearly 100 million tons, are considered a potential source of iron. Various accessory elements are associated with the iron minerals and these pose metallurgical and economic problems.

Jan 1, 1964

By C. M. Harrer

Reconnaissance investigations were made of 129 iron occurrences in Arizona to determine their extent, attitude, and potential; character samples were analyzed to determine their quality and impurities; and pioneer metallurgical investigations were made on character samples to present their metallurgical problems. Some factors influencing past and potential western iron markets are discussed. The location, features, qualities, extent, and potential of iron occurrences and some associative resources--limestone and dolomite, coal, petroleum and natural gas, power, and water are discussed. The most abundant iron minerals are magnetite and hematite. The higher grade deposits are extensive contact-metamorphic or pyrometasomatic replacements of calcareous Paleozoic to Proterozoic rocks associated with intrusives. Large low-grade deposits of great potential are present as Precambrian taconite, semitaconite-, and jaspilite-like iron formations of magnetite-hematite. Iron occurs also as low-grade concentrations of magnetite in extensive alluvial deposits. Nonferrous metallurgical slags, nearly 100 million tons, are considered a potential source of iron. Various accessory elements are associated with the iron minerals and these pose metallurgical and economic problems.

Jan 1, 1964

By M. M. Gilkey

This report on water requirements for the New Mexico mineral industry includes data on industrial operations closely related to mineral production. It contains general information concerning public water supplies at five principal cities and a short discussion of water needs for agriculture. Background data are presented regarding the geography, hydrography, and water laws of New Mexico, as well as precipitation and evaporation characteristics of the State. Most of the information on source, quantity, distribution, cost, and treatment of water was obtained in interviews with company representatives. Water systems at 46 operations are illustrated by schematic waterflow diagrams. The study revealed that the New Mexico mineral industry in 1962 used about 16 billion gallons of new water and reused 152 billion gallons, a total usage of 168 billion gallons. Consumption amounted to 7.6 billion gallons. Of the 16 billion gallons of new water, 11.9 billion gallons was "self- supplied" from ground water sources, and 2.6 billion gallons was self supplied from surface sources. Approximately 1.5 billion gallons was purchased. Some of the water from company-owned wells is piped as far as 30 miles. Reported costs of the self-supplied new water range from 1 to 20 cents per 1,000 gallons and average 8 cents per 1,000 gallons for power and maintenance. Inadequacy of the supply of new water at many operations necessitates large-scale recirculation. Reported costs for recirculating water (power and maintenance) average 1.8 cents per 1,000 gallons. For the entire New Mexico mineral industry in 1962, the value of product was $42 per 1,000 gallons of new water intake and $88 per 1,000 gallons consumed. Analyses of 40 water samples, listed in the appendix, show the wide range in water quality at plants throughout the State. Projection of the 1962 water requirements of the mineral industry indicate that the total demand for new water will increase from the 16 billion gallons used in 1962 to 24 billion gallons in 1980, a 50 percent increase; and to 36 billion gallons in 2000, which is 125 percent more than the 1962 intake of new water.

Jan 1, 1965

By M. M. Gilkey

This report on water requirements for the New Mexico mineral industry includes data on industrial operations closely related to mineral production. It contains general information concerning public water supplies at five principal cities and a short discussion of water needs for agriculture. Background data are presented regarding the geography, hydrography, and water laws of New Mexico, as well as precipitatton and evaporation characteristics of the State. Most of the information on source, quantity, distribution, cost, and treatment of water was obtained in interviews with company representatives. Water systems at 46 operations are illustrated by schematic waterflow diagrams. The study revealed that the New Mexico mineral industry in 1962 used about 16 billion gallons of new water and reused 152 billion gallons, a total usage of 168 billion gallons. Consumption amounted to 7.6 billion gallons. Of the 16 billion gallons of new water, 11.9 billion gallons was "self- supplied" from ground water sources, and 2.6 billion gallons was self supplied from surface sources. Approximately 1.5 billion gallons was purchased. Some of the water from company-owned wells is piped as far as 30 miles. Reported costs of the self-supplied new water range from 1 to 20 cents per 1,000 gallons and average 8 cents per 1,000 gallons for power and maintenance. Inadequacy of the supply of new water at many operations necessitates large-scale recirculation. Reported costs for recirculating water (power and maintenance) average 1.8 cents per 1,000 gallons. For the entire New Mexico mineral industry in 1962, the value of product was $42 per 1,000 gallons of new water intake and $88 per 1,000 gallons consumed. Analyses of 40 water samples, listed in the appendix, show the wide range in water quality at plants throughout the State. Projection of the 1962 water requirements of the mineral industry indicate that the total demand for new water will increase from the 16 billion gallons used in 1962 to 24 billion gallons in 1980, a 50 percent increase; and to 36 billion gallons in 2000, which is 125 percent more than the 1962 intake of new water.

Jan 1, 1965

By Stephen M. Jasinski

The development and industry adaptation of advanced technologies have led to many important uses for bismuth and its compounds. Bismuth-base alloys are essential for manufacturing jet engine turbine blades, lenses, and various safety devices, such as fire-protection sprinklers. The addition of bismuth to iron, steel, and aluminum imparts properties to these metals that makes them useful in diversified applications. Bismuth is also used widely in medicine, pigments, and electronics. The United States relies heavily upon imports from South America and Europe to meet its demand for bismuth, which is recovered chiefly as a byproduct of lead processing.

Jan 1, 1992

Minerals are vital to any industrialized civilization. Annually, the United States uses more than 4 billion tons of new mineral materials, or about 40,000 pounds per person-about half being mineral fuels and the other half metals and nonmetallics. Stable and economic domestic mining, mineral, metal, and mineral reclamation industries are essential to the economy. The value of United States energy and processed materials of mineral origin exceeds $200 billion annually. Although a number of minerals are imported, especially some designated as "strategic and critical," most U.S. mineral supplies are derived from the domestic mines and processing facilities that you will be seeing, reading about, and visiting as you use this visitor guide. We hope you enjoy your experiences. This pamphlet, a guide to mining and mineral operations that may be observed or visited and some other points of interest relating to minerals, is intended to aid tourists and students who are interested in mining. Some may wish to study our Nation's romantic past; others may plan to enter the minerals industry as a career; still others may have a primary interest in conservation practices. The pamphlet is also intended to aid State and local officials, Chambers of Commerce, and mining firms in answering some of the many questions of tourists and students.

Jan 1, 1977

By Robert C. Merritt

This report describes laboratory as well as pilot heap leaching investigations of low-grade sandstone ores from Wyoming, New Mexico, and Colorado. Sodium carbonate-bicarbonate solutions containing sodium hypochlorite extracted up to 86, 54, and 16 percent U308 from Wyoming, New Mexico, and Colorado ores, respectively. Ammonium carbonate-bicarbonate solutions containing sodium hypochlorite were less effective at leaching these ores. Acid leach in replicate pilot plant testing resulted in U308 extractions of 96, 88, and 81 percent from the Wyoming, New Mexico, and Colorado ores. The development of cost-effective processes for extracting uranium from low-grade ore is essential to the assurance of a continuing domestic supply of uranium.

Jan 1, 1977

By Larry A. Haas

The Bureau of Mines is investigating the use of complex gas mixtures, such as would be produced by coal gasification, for reducing iron oxide pellets. A semiempirical model was developed to predict a priori the reduction rate of an iron oxide pellet in a laboratory tube furnace with simulated coal gases at a total pressure of 1 atm. The model uses partial pressures of H2, CO, CO2, CH4 (methane), water vapor, and a temperature-dependent term to predict the rate of reaction. The reduction rate (weight loss per unit of time) was determined with a thermo-gravimetric apparatus (TGA) in the temperature range of 800° to 1,100° C. The ranking of the reductants, in order of decreasing reducing potential, is H2, CO, and CH4 at temperatures between 800° and 1,000° C; however, CH4 became a better reductant than CO at 1,100° C. Water vapor did not decrease the reduction rate as much as did CO2, Carbon deposition was observed at temperatures below 1,000° C with gas mixtures with high CO and low H2 concentrations. With low-Btu gas at 900° C, over 90 pct of the iron oxide was reduced to iron in less than 3 h. This com-pares with a reduction time of 1.5 h with medium-Btu gas and 1 h with reformed natural gases.

Jan 1, 1985

By J. R. Thoenen

This circular is part 2 of the third subject (entitled "Excavation") of a series summarizing; the technical problems involved in the production and preparation of sand and gravel. Part 1 discussed the use of power shovels, draglines, and excavator cranes. This paper discusses the use of the power scraper, slackline cableway excavator, and hydraulic monitor, and part 3 will discuss the use of various types of dredges. Subsequent papers in the series will discuss the use of haulage equipment, the application of both excavating and haulage equipment to various types of deposits, and operating costs. THE POWER SCRAPER The power scraper is a younger member of the various forms of gravel excavators. It is a mechanized enlargement of the slip scraper and other scrapers which depend upon animals for power and has a greater range of operation from a single set-up than any other excavation unit except the slackline cableway excavator.

Jan 1, 1935

By M. L. Whisman

The Bureau of Mines developed and tested in the laboratory several innovative techniques for reclaiming used lubricating oil. These processes included percolation through both chemically treated clay and ion-exchange resins, distillation through batch and continuous wiped-wall vacuum apparatus, treatment with solvent extraction systems, and chemical removal of impurities with chelating agents. In each treatment, the criteria of evaluation was oil recovery and reduction of acidic and metallic components. Both vacuum distillation and solvent treatment ranked high in their abilities to remove acidic and metallic components of the used oil with good oil recoveries. A combination of the two techniques gave the best overall results in terms of quality evaluations made by established bench tests. The methods were not ranked according to economic practicablity.

Jan 1, 1974