Search Documents

By R. O. Kneisley

This U.S. Bureau of Mines report summarizes a study of large-scale strata response to longwall mining at a western U.S. coal mine. This study utilized surface and subsurface measurements, geologic mapping, in situ stress measurements, and pressure cell readings to characterize strata behavior. Preliminary analysis of surface subsidence and time-domain reflectometry (TDR) was used to determine a suggested main roof caving sequence. Coal ejected from the face apparently resulted from brittle failures that occurred because of lack of significant yield zone development. The combination of a strong coal with pronounced directional behavior, low overburden pressures, a good caving roof, and a high-production environment that minimized time-dependent loading apparently reduced yielding of the longwall face. The panel 1 headgate-entry design appears adequate; however, the abutment pillar and adjacent panel tailgate rib are highly stressed and may contribute to problems during second panel mining. The small chain pillar yielded after passage of the face, but the pillar width may be near maximum since evidence of a stressed core exists.

Jan 1, 2010

By J. D. Ramsdell

The object of this investigation by the Federal Bureau of Mines was to evaluate the workability, recrystallization characteristics, and mechanical and physical properties of high-purity electrorefined vanadium. The low level of interstitially soluble elements in electrorefined vanadium results in a soft ductile metal which responds readily to cold working by rolling, swaging, and press-forging. Hardness, strength, and resistivity increased with an increase in impurity content, but thermal expansion was independent of impurity content. The work-hardening of vanadium occurs rapidly. Most of the hardness increase occurs in the first 15 pct. of reduction in area. When vanadium is annealed, its hardness increases to a maximum when the annealing temperature is between 200° to 400° C. A sharp decrease in hardness develops as the annealing temperature is increased. An anomaly in the hardness versus annealing temperature curve is present in the 600° to 800° C. range, while all evidence of cold-work is removed at annealing temperatures above 900° C.

Jan 1, 1961

By P. L. Swanson

Stability analyses of fractured and faulted rock masses require delineation of the position, extent, and orientation of geologic discontinuities. The size of the smallest active discontinuity that may potentially be resolved using the spatial distribution of microseismic event locations is Limited by the accuracy and precision of the location methods. At a hard-rock mine in the Coeur D'Alene mining district of northern Idaho, two data sets consisting of calibration blast signals from a known source site and origin time and microseismic event signals were recorded using a stope-wide accelerometer array. These seismic signals are used to quantify various sources of error in event location. Five factors influencing source location errors are examined in this U.S. Bureau of Mines study: (1) biases of the numerical source location techniques, (2) receiver array geometries, (3) uncertainties in receiver positions, (4) errors in picking arrival times, and (5) uncertainties in seismic velocity structure, including the effect of mine openings. In addition, synthetic data (accelerometer positions, travel-time picks and wave velocity) are used to determine the effect of known systematic and random errors on source location calculations. It is shown that the commonly accepted association of minimum travel-time residuals with the best location solution does not necessarily hold true when there is a systematic error in seismic velocity. Recommendations are made for increasing the accuracy and precision of locations of microseismic events detected under similar field conditions.

Jan 1, 2010

Bosworth, T. 0. The Mackenzie oilfield of northern Canada. Petroleum Times, vol. 5, Apr. 30, 1921, pp. 489-491. Jour. Inst. Petroleum Technologists, vol. 7, Oct., 1921, pp. 276-290; discussion, pp. 290-297. Gives location of the field, some of its geology, mode of occurrence and character of the oil. See also Oil Trade Jour., vol. 12, June, 1921, pp. 48-108. Canadian Min. Jour., vol. 42, May 27, 1921, pp. 420-422. Oil and Gas Jour., vol. 20, June 3, 1921, pp. 90-90. Petroleum World (London), vol. 18, June, 1921, pp. 233-2.64, 236-238, 240-241. Bull. Canadian Inst. min. and met., July, 1921, pp. 629-638. Mining and Metallurgy, Oct., 1921, pp. 47-48. Bureau of Foreign and Domestic Commerce. Resources of Balkan and Near Eastern countries. Commerce Repts., Oct. 24, 1921, pp. 488-489. Includes summary of the mineral resources of these countries, mentioning petroleum and allied substances in Roumania, Albania, Anatolia, Mesopotamia, Palestine, Arabia, Persia.

Jan 1, 1921

By Almon F. Robertson

"INTRODUCTION At various times, North Carolina has supplied small quantities of brown-iron ore to the furnace o the South. Between 1917 and 1920, the quantity reported to the Federal Geological Survey was 126,000 tons. Most of this came from Cherokee County. 3/In furtherance of the program initiated by the Bureau of Mines to develop additional reserve of iron ore during the emergency, the Cherokee County deposits were examined by an engineer 4/ of the Bureau of Mines, and work was recommended on,12 properties.The project was begun in April 1944 and continued intermittently until April 1945, when work was stopped. During this period, eight properties were explored, and an additional property was mapped.ACKNOWLEDGMENTSIn its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch; Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metallurgical Branch, R. G. Knickerbocker chief, analyzes samples and performs beneficiation tests. Both these branches are under the supervision of Dr. R. S. Dean, assistant director."

Nov 1, 1946

By R. L. Beatty

IN INDUSTRIAL and domestic daily life carbon monoxide is the most frequently encountered toxic gas. hazardous concentrations of carbon monoxide may be present in the vicinity of many industrial operations, such as metallurgical processes, coke ovens, and fuel- and synthesis-gas producers, and may be encountered in confined spaces, such as dwellings, garages, workshops, vehicular tunnels, and mining operations, in connection with the use of heaters, boilers, internal-combustion engines, after blasting operations, and after fires and explosions. Evaluation and control of the health and safety hazard caused by carbon monoxide depend primarily on the analytical detection of the presence of carbon monoxide and determination of its concentration in air and in various gaseous mixtures. The choice of method of analysis in any particular situation depends on such factors as required accuracy, range of concentration involved, convenience, speed of analysis required, quantity of sample available, qualitative composition of sample or atmosphere to be analyzed, and possible effects of interfering gases. Some of the methods described require only adequate understanding of operational techniques, whereas others require thorough appreciation and skill in applying the principles involved. The instruments and analytical procedures commonly used for detecting and determining carbon monoxide are described in detail, and reference is made to more specialized methods:

Jan 1, 1955

By J. G. Walters

Analyses of light oils produced from the fluidized carbonization of coal at 485°, 550°, 600°, and 660° C are presented. Tar vapors from 485 C fluidized carbonization were thermally treated at 600°, 700°, and .800° C, and the analyses of light oils produced by this treatment are also presented. Procedures were developed for analysis of coal carbonization light oil by gas chromatography to permit a more definitive analysis than can be obtained by the conventional distillation procedure. An increase in low-boiling olefins, benzene, and toluene, a decrease in low-boiling paraffins, and little change in the remainder of the aromatics was observed with increased temperature of carbonization.

Jan 1, 1965

By Steven W. Schmauch

In 1985, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied 27,930 acres of the 52,000 acre East Fork High Rock Canyon Wilderness Study Area, CA-020-914/NV-020-006A, in order to evaluate the mineral resources. The study area is located in Humboldt and Washoe Counties, NV, about 45 miles east of Cedarville, CA. Bureau of Mines personnel reviewed pertinent literature and county mining records and examined prospects or mineralized areas. There are no organized mining districts and no historical or active claims in the study area; one small pit lies in the southwest corner of the study area. Based on published literature, sample results and field observations, there are no recognized mineral, geothermal, or fossil fuel resources. Epithermal mineralization indicators are not present or exposed. Sand and gravel deposits in the study area are not likely to be developed as other deposits are closer to market areas.

Jan 1, 1986

By Herbert Cremer

The United States,-the largest nickel consumer in the world, produces virtually no nickel from domestic ores. Dependence upon outside nickel - sources and increasing strategic, importance of nickel focused the attention of the United States on deposits within its boundries. The most likely domestic sources of nickel are low-grade oxide and silicate deposits, such as the Cle Clum deposit, Kittitas County, Wash., and the Riddle deposit, Douglas County, Oreg. The Federal Bureau of Mines, Northwest Electrodevelopment Laboratory, Albany, Oreg. has been investigating electric smelting of low-grade oxide and silicate nickel ores. These smelting studies have been on selective reduction to produce low-carbon ferronickel. Selective reduction is based upon the relative reducibility of: nickel, iron, and chromium, in the order named, when the charge contains insufficient carbon or other reductants to reduce the entire quantity of these metals present in the ore.

Jan 1, 1954

By R. HOLROYD

The Ludwigshafen and Oppau plants are largely independent I. G. factories situated some 23 miles apart on the west bank of the Rhine facing lannheim. The former factory is a general organic chemical works specializing in dyes, dye intermediates, plastics and synthetic rubber,. while the latter is a heavy organic chemical factory producing ammonia, methanol, higher alcohols and their derivatives. Before the war much of the I. G. research and development work was carried out at Ludwigs- hafen; in particular the high pressure research section directed by Dr. Mathias Pier played a very active part in all hydrogenation developments. Apart from the possibility that a full scale hydrogenation or Fischer Tropsch plant had been erected at Ludwigshafen/Oppau during the war, the main objectives of an oil team investigation were: - (a) To obtain from Dr. Pier and his staff an advance general picture of German fuel production processes. (b) To study the fuel developments still in the research and pilot plant stage. (c) To examine any new developments in hydrogen or synthesis gas manufacture. (d) To look for new processes for production of high anti-knock fuel constituents and for new fuel additives. (e) To investigate new chemical syntheses based on raw materials obtainable from oil. The Ludwigshafen and Oppau factories were first visited by the large team listed in Appendix A during the period 25-31st March. The investigation revealed that no large plant for synthetic fuels or lubricants had been operated at this target. All the important members of the Fuel Research Section staff had been evacuated to Heidelberg and information on the work of this department was therefore limited to that contained in seized documents, the greater part of which have still to be examined in detail. Valuable information on synthesis gas production from hydrocarbon gases was obtained as well as interesting data on a num- ber of chemical syntheses. Two members of the above team Holroyd and Faragher accompan- ied by Major Tilley (interrogator) went on to Heidelberg, contacted Dr. Pier and the chief members of his staff on April 1st and obtained from them the hydrogenation information given later in the body of the report. Later, after visiting Leuna, Holroyd, Faragher and Ellis paid a second visit to Heidelberg and to Ludwigshafen/Oppau on 27th-30th May to check a number of details, particularly with respect to hydrogenation costs, and to obtain information on the pressure.conversion of water gas to hydrogen and on the manufacture of Wickel pressure vessels.

Aug 1, 1943

By J. W. Eckerd

This report describes an investigation of the technical feasibility of using a conventional commercial-size (10-ft. i.d.), rotating grate, dry-ash-removal type gas producer to make producer gas from chestnut-size bone anthracite. Test instruments were installed, and some minor changes were made in the equipment to handle the large quantities of materials expected. Extensive tests, lasting about 4 weeks, were planned, using 35 to 50 percent ash chestnut anthracite bone. However, operations were suspended after 8 days when it became apparent that to use this type of fuel satisfactorily substantial changes in equipment and operating procedures would be required. Nevertheless, enough data were obtained to indicate that gas could be produced continuously and routinely from bone coal in this type of producer whenever conditions justified the necessary development work.

Jan 1, 1960

By W. A. Young

Bull Lake is one of several saline lakes situated a few miles north of Rawlins, Carbon County, Wyo. (figs. and 2).. The Bureau of Mines conducted preliminary investigations of sodium sulfate deposits in many of the lakes and performed detailed work on Bull Lake. This investigation consisted of drilling 11 vertical holes through salt beds using diamond core bits and Iwan-type auger bits. Bull Lake lies in a shallow, closed depression in loosely consolidated sand. The salt beds, ranging in thickness from 2.5 to 26 feet, occur above a thick bed of shale of upper Cretaceous age. The salts appear to have been deposited in the lake from surface and subsurface drainage. The source of salt is undoubtedly the enclosing sedimentary rock's exposed to the west of the basin. Sodium sulfate in the deposits probably is present as mirabilite or Glauber salt (Na2SO4-10H2O). Chief impurities in the deposits arc mud and sand. Other soluble salts present average approximately 1 percent combined. Cores from the 11 holes were analyzed in the Bureau of Mines laboratories at Salt Lake City. Drilling totaled 512 feet. Results of analyses are given in the appendix.

Jan 1, 1951

By Carl R. Peterson

Development of reliable, portable, low headroom, hard rock crushers would improve the efficiency of most currently operated conveyor systems and make it possible to bring conveyor haulage closer to the face, thus eliminating expensive rock rehandling procedures. A crusher that could be easily moved would permit the more widespread use of lower cost haulage systems, such as conveyors, to transport the ore out of the mine. Such crushers would be installed close to the working areas, resulting in an optium haul from the face to the dump location. A recent contract study by Rapidex, Inc., "Application Study of Portable Underground Hard Pock Crusher" (USBM Contract No. J0265006) provides a survey of industry needs in portable underground crushing, together with conclusions and concepts as to specifications and type of crusher required to serve the greatest number of operations. To fill this need a three phase program has been undertaken by the Bureau of Mines: Phase I - Design: Phase II - Construction and Testing, and Phase III - Production Underground Test. This report covers Phase I only, and includes the complete engineering design and specifications of the Rapidex Rotary Jaw Crusher conceived in the earlier "Applications Study". Also included are the design, construction, and testing of a quarter-scale functional model, utilizing three different types of rock and two different crusher feeder systems.

Jan 1, 1978

By J. E. Chilton

The U.S. Bureau of Mines has developed an intrinsically safe carbon monoxide (CO) monitoring system for mines by coupling a fiber-optic data telemetry (FODT) system with a prototype electro-chemical CO monitor. The CO monitoring system can be used in a coal mine as one component of an early fire warning system. This system may be used in belt haulage entries when the entries are used for supplying ventilation air to working places. The FODT accepts a 0.1-to 1.1-V analog signal from the monitor and converts it to pulses (0 to 5 V) at frequencies from 1.1 to 11 kHz that drive a light-emitting diode (LED). An electrically nonconducting fiber-optic cable carries the LED signal to a remote receiver. The receiver analyzes the incoming light signal and displays the measured CO concentration in parts per million. This report discusses the performance of the FODT system and characteristics of the CO monitor such as response times, linearity, and temperature and pressure effects.

Jan 1, 2010

By A. L. Engel

[This report presents results of investigations of problems assigned as ore-testing projects to the Ore-Dressing Section, Metallurgical Division, of the Bureau of Mines at the Mississippi Valley Experiment Station in Rolla, Mo., during the fiscal year ended June 30, 1940.]

Jan 1, 1941

By Arno C. Fieldner

In view of the widespread interest in the production of synthetic liquid fuels from solid and gaseous fuels to supplement declining reserves of petroleum, and the many requests that are now being received for information on the subject, this bibliography of Bureau of Mines contributions has been compiled. In addition to the publications issued by the Government in printed or mimeographed form, references are included to articles written by the Bureau staff for the technical press and to cooperative reports of work done jointly with States, colleges, and industries. References are given under each section in chronological order. Bureau of Mines bulletins, technical papers, and Minerals Yearbooks are printed and are obtainable at the prices indicated from the Superintendent of Documents, Government Printing Office, Washington 25, D. C. If no price is given, the publication is out of print. The price of entire volumes of the Minerals Yearbook or of reprints of certain chanters may be obtained upon request. Any orders or remittances in payment for these publications should be cent directly to the Superintendent of Documents and not

Jan 1, 1945

By G. L. Humphrey

Although silicon carbide has been an important manufacture refractory for many years, knowledge of its thermodynamic values has been seriously lacking. In fact, some of the very properties that make it a useful substance, particularly chemical inertness, obstruct determination of its heats of formation and reaction. This paper reports the results of new measurements of the heats of combustion and formation, low-temperature heat capacity, entropy at 298.16°K., and heat-content and entropy increments between 298° and l,800°K. Two varieties of silicon carbide were studied -the common, hexagonal (type II) and cubic. The data are combined to obtain heat and free-energy-of-formation functions, which are given in tabular form. It is shown that the cubic variety is the more stable at temperatures to at least 1,800°K but, because of the inherent difficulties and errors in the heat-of-formation determinations at 298°K, it was not found possible to specify the free-energy difference accurately. The mechanism of silicon carbide formation from silica and carbon is not known and is not ascertainable from thermodynamic data. It appears improbable, however, that it can be a single-step reaction. Some reactions involving silicon monoxide gas and metallic Silicon, as possible intermediates in silicon carbide formation, are considered and shown to be thermodynamically feasible.

Jan 1, 1952

By G. J. Hundman

Control of respirable dust produced by auger type continuous mining machines is normally attempted by water sprays from fixed nozzles mounted on the frame of the machine. In tests conducted under this contract, a 'wet auger' system was used, where the spray nozzles were mounted on the rotating auger itself. The tests were conducted at the Hunter mine of Smith and Stover Coal Company using a Jeffrey 1.00L auger miner. Operating the mining machine in the wet auger mode, it was found to produce 47 pct less respirable dust than when the fixed conventional sprays were used. On section dust levels were reduced too 3.5 mg/m3 which is equivalent to approximately 2.0 mg/m3 for a full shift portal to portal sample. The major difficulty that had to be overcome was the development of a simple reliable water transfer mechanism to get the water into the rotating augers. This was successfully achieved by the development of a water-through-the-shaft water system. This system can be retrofitted to existing machines and is available in kit form.

Jan 1, 1977

By Robert A. McColly

This Bureau of Mines report compares the availability of federally owned minerals in Arizona with lands considered favorable for discovery of mineral resources, to deter-mine the extent to which Federal mineral lands in such areas have been withdrawn by legal action or restricted by management practice. Of particular concern are restraints on Federal lands in areas identified as highly favorable for occurrences of valuable mineral deposits. Excluding Indian lands held in trust by the Federal Government, about 32 million acres, 44%, of Arizona's mineral estate is federally owned. This total includes lands with partial Federal mineral ownership. Approximately 16.5 million acres, or 52% of these lands, are available for location or lease. This includes 496,000 acres, 62%, of the lands highly favorable, and 2.6 million acres, 57%, of the lands moderately favorable for locatable minerals in Arizona. All other Federal mineral lands are either withdrawn or restricted, reflecting a wide range of purpose, authority, and impacts on mineral exploration and development.

Jan 1, 1987

By Robert H. Peters

Groundfall accidents have been the leading cause of fatalities in the underground coal mining industry for many years. Statistics from the Mine Safety and Health Administration (MSHA) indicate that approximately half of the victims of these fatal accidents were in an area where no devices had been installed to support the mine's roof. This report was prepared by the U.S. Bureau of Mines to summarize the opinions of 268 coal miners, 29 rust-line supervisors, and 30 MSHA inspectors concerning why people go under unsupported roof, and how to prevent this behavior. Interviews were conducted at six minesites.

Jan 1, 1991