Search Documents

By John J. Sammarco

The mining industry has the highest average annual fatality rate among major U.S. industries. To address this, the National Institute for Occupational Safety and Health, Pittsburgh Research Laboratory (PRL), is conducting major research programs to reduce the hazard exposure of miners. One of the recently concluded programs at PRL developed the enabling technology for remote-controlled mining. An application involves the manual process of extracting and hauling coal where operators, in the tight confines of a mine, can be struck or caught by mobile machinery. The approach to remedy this problem uses a guidance system on the continuous haulage equipment so that it follows the continuous mining machine that extracts coal. This, in essence, involves sensor-based docking of the machines. Sensors functioning in the hostile mine environment of dust, methane gas, and water play the key role. Computer analysis of the mining machine's movements and empirical machine characterizations established operating requirements and spatial limitations to ensure proper loading of coal into the haulage equipment. These data served in the selection of a guidance sensor. Technologies such as scanning laser systems and ultrasonic sensors have frequently been used in other applications, but were found unacceptable. However, a near-infrared sensor employing active targets met the requirements. The sensor has a nominal 75b conical field of view and a range from 0.1 to 18.0 m. For the single-target mode, nominal range accuracy was 4.3% at a distance of 3.65 m. Correction algorithms were generated, which reduced the error to 0.6%. Airborne dust testing showed less than an additional0.8% accuracy (worst case) degradation at dust levels up to 15 mg/m3. Using four targets, the nominal range accuracy was 0.4% without correction algorithms. Analysis of dynamic testing of a continuous miner and haulage showed that accuracy was maintained and total target loss did not occur. A guidance system for the haulage system to follow the mining machine does not exist commercially. Such a system can reduce fatalities, injuries, and exposure to dust and noise.

Jan 11, 1998

By A. C. Fieldner

This report, the third of a series of annual reports of research and technologic work on coal by the Technologic Branch to be released in this form, covers the fiscal year July 1, 1937, to June 30, 1938. Ever-increasing demands for information on the chemical and physical properties of coals, their proper classification rind adaptability for various uses, their economic evaluation in the complex relationships between the costs of production, distribution, and selling, and their beneficiation and amenability to conversion to more valuable and. new products of commerce have necessitated an appropriate and flexible program. To most these requirements, initiation of new projects and new physical facilities has been made.

Jan 1, 1939

By E. G. Davis

As a result of interest by the U.S. Department of Energy, the Bureau of Mines conducted studies on comminution of bituminous coal to the 2-um particle size range using the Bureau-developed turbomill. Both "plant grind" size (80 pct minus 75 um) and microsize (minus 10 um) coal can be produced in a single step with the Bureau's turbomill. In 15 min, minus 2.4-mm coal milled in water with steel shot was reduced tc 65 pct minus 75 m and 26 pct minus 2 m, with an energy requirement of 139 kW^h/mt coal. Plant-grind size coal milled in water, with Ottawa sand as the milling medium, was reduced to more than 45 pct minus 2 m in 15 min, at 175 kW?h/mt. Plant-grind coal milled with steel shot was reduced to 57 pct minus 2 um in 15 min, at 138 kW?h/mt. When diesel fuel was substituted for water, the milling of the coal was less effective and less energy efficient. Keeping the pulp dispersed was critical. Without an effective dispersant, the slurry became very viscous with increased milling time, resulting in higher energy requirements, low heat dissipation, and poor grinding efficiency.

Jan 1, 1987

By L. C. IlsLey

The increasing use of Diesel engines for operating equipment on trunk-line railroads and for power-plant units has stimulated interest in the use of Diesel engines for other lines of work, among which is the possibility of substituting Diesel locomotives for trolley locomotives for mines. The possibility of developing Diesel locomotives for duty in American mines is not as remote as it might seem, particularly in view of the fact that locomotives of this type are already used in considerable numbers in European mines. A study of Diesel locomotives in Europe is contained in Report of Investigations 3320, Diesel Mine Locomotives - Development and Use in European Coal Mines, by George S. Rice and F. E. Harris.

Jan 1, 1938

By Albert L. Toenges, Theodore R. Jolley

"INTRODUCTION The construction of frame houses (fig. 1) in recent years instead of the conventional sod hut (igloo) (fig. 2) by the Eskimos in the villages along the Arctic Ocean has increased the demand for fuel in these villages. The frame houses, which are not insulated against extreme cold and are difficult to heat, are equipped with Goal stoves. The well-insulated sod huts were heated comfortably with whale-oil stoves. In some years whaling is Door, consequently there is a demand for solid fuel.The Eskimo villages usually are on the sand spits at the mouths of rivers and points of land near the best fishing and hunting grounds. These narrow necks of land usually are sand bars that are not underlain with coal, and coal must be transported to the villages. Lack of development of coal deposits in the Arctic has made it necessary to import coal from the States, generally from 'Washington, to supply these villages. This coal is imported by boat and is received once a year. Its cost is, high, and development of coal deposits in the Arctic to supply these native villages should result in a considerable saving to the Government-operated schools and hospitals as well as to the natives.Early traders attempted to establish coaling stations in the Arctic, and the Eskimos generally know where the coal deposits are situated. A. reconnaissance of a number of deposits in the Arctic was made in the summer of 1946 by engineers of the Coal Division, Fuels and Explosives Branch, Bureau of Mines, and this report describes the areas investigated and suggests plans for the development of some of these deposits."

Dec 1, 1947

By D. E. Andrews

The objective of this study was to investigate the environmental effects of slaking of surface mine spoils. To accomplish this, both field and laboratory programs were undertaken, supplemented by a thorough literature search. The field program consisted of drilling the highwall as well as test pitting in recent, two-, five, and ten- year-old spoil piles at four active mining sites in the eastern bituminous coal fields. Pertinent observations were made and samples collected for laboratory analyses which consisted of several standard geotechnical, agronomic, and geochemical tests. Durability tests utilized included jar slake, cyclic wet-dry, rate of slake, and slake durability tests. Correlation between field and laboratory portions was made- and results presented. The report is concluded with a discussion of the slaking process and associated environmental impacts, proposal of a preliminary classification system for use in premine planning, and presentation of management techniques to optimize the slaking process.

Jan 1, 1980

By John R. Benham

The Bureau of Mines examined the Bear Canyon RARE II area in 1982. The area has no identified mineral deposits. The few claims that were located in the study area are devoid of any workings. No concentrations of economic minerals were found in the samples taken. There are no mineral, geothermal, or oil and gas leases in the area; the nearest oil well is 10 mi (16 km) east. The nearest mining operation was the Ruby Gold Placer worked in 1914, 7 mi (11 km) southeast (Hart, 1966, p. 45); the Pliocene Paso Robles Formation which contained the gold does not extend into the area. SETTING The Bear Canyon RARE II area covers 19.7 sq mi (51 sq km) or 12,600 acres (1500 ha) in west-central California. It lies in the Santa Lucia Range 10 mi (16 km) southwest of King City and adjoins the southeast side of the Ventana Wilderness. It is 10 mi (16 km) from the Pacific Ocean. Primary access is by the San Antonio River road on the Hunter Liggett Military Reservation, which parallels the area's southern border. Further access to the area's interior is by jeep and foot trails.

Jan 1, 1983

By E. L. McHugh, J. M. Girard

This paper discusses the results of two recent case studies in which high-tech prototype instruments were used. The first case study describes the results of a ground-based hyperspectral imaging tool used to map the geology of an open-pit mine highwall. The second case study outlines the use of interferometric synthetic aperture radar and how this type of radar can be used in a variety of geotechnical situations. These case studies are part of an on-going research project at the National Institute for Occupational Safety and Health’s (NIOSH) Spokane Research Laboratory. The project objective is to implement engineering controls and design methods in order to reduce the number of injuries and fatalities associated with slope failures at mining operations. Project personnel are hopeful that these new developments in technology will lead to better geotechnical monitoring and design in slope stability and other important areas of rock mechanics.

By K. E. Stanfield

[Asphalt ~~d road oil ar8 the principal products manufactured from Wyor.1in~ Ilblack oilo" \r,hich, beca.use of th?lir hig.~ E\.sphal t and hig} sulfur COi.1Jce~1t, .!?re difficult e':ld costly to refine into hi?;h-gra.de motor f 101s, burning oils. and lucri ants by presont mothods. Accordin~ly. the demand for truHle asphaltic renidl urn for the construction of roade aJ1.d other uses is 3. controlling factor in the quantity of crud~ oil prod ICed. The increasiilg -u.tilization of special aST>ha.lts as ine}""Pensive bonding, in-]

Jan 1, 1941

By N. Kumar Kittusamy

ALTHOUGH MANYSTUDIES HAVE SHOWN an association between operating heavy construction equipment and symptoms of musculoskeletal disorders (MSDs), little research has been performed that systematically characterizes the exposure of operating engineers to ergonomic hazards. This study evaluated: 1) vibration at the seat/operator interface;2) transmissibility of vibration in the Z-axis; 3) psychophysical ratings of vibration level and vibration discomfort; and 4) postural requirements of the job. Results indicate that the digging operation had higher levels of total weighted acceleration than high- or low-idling conditions. Transmissibility data showed that the seat amplified vibration, particularly in the lower frequencies. Seats demonstrated that they may not be sufficient in protecting operators from long-term effects of vibration exposure. High positive correlation was found among subjective ratings (vibration discomfort and vibration level), but moderate positive correlation was found between subjective ratings and quantitative vibration levels. Postural evaluations revealed that the operators were required to assume awkward postures of the neck, shoulder and trunk while performing their jobs. Work-related injuries and illnesses pose a continuing threat to the health and well-being of American workers. The construction industry has been historically recognized as having higher rates of fatality, injury and illness than other industries (McVittie285+; BLS). In 1994, an estimated 218,800 lost-work-day injuries were reported in the construction industry (BLS). Construction also had the second-highest incidence rate for sprains and strains. Although the industry has made progress since then, injuries and illnesses, including MSDs, continue to because for concern.

By L. C. IlsLey

Many accidents rightly classifiable as electrically caused are not so classified for the reason that in numerous accidents the part that electricity played in causing the fatality is only suspected. For instance, a workman might receive a shock that would cause him to lose his balance and fall beneath a trip of cars; if no one saw the first part of the accident, the cause undoubtedly would be charged to "haulage." This paper covers a brief study of fatal and nonfatal electrical accidents. The first usually result from direct contact with the electrical circuit or electrical apparatus; the second more often are the result of arcing or flashing due to handling defective apparatus or making repairs on "live" equipment or circuits. It is hoped that helpful suggestions may be offered for minimizing accidents of these two classes.

Jan 1, 1938

By Stephen R. Iverson

Mineral deposits examined in and near the Raywood Flats RARE II area have low potential for development. The Mill Creek Mine (fig. 1), has produced about 14,000 tons (13,000 t) of marble, and another 5.5 million tons (5.0 million t) of marginal marble reserves suitable for lime, chemicals, and cement production are estimated to remain at this deposit. However, nearly all the marble is outside the study area. The deposit is marginal because alternate sources of marble are closer to markets. A tungsten occurrence in the marble is too small and low grade to be considered a resource. Ten tons (9.1 t) of uranium- and thorium-bearing material have been mined from a pegmatite dike at the St. Patrick Mine. However, this occurrence also is too small and low grade to be considered a resource. More than 400 lode and placer claims have been located in or near the study area. There are no current claims or mineral, oil and gas or geothermal leases.

Jan 1, 1983

By John E. Urosek, Dennis A. Beiter, William J. Francart

In This Chapter [Designing bleeder systems Examining and maintaining bleeder systems Evaluating bleeder system effectiveness] INTRODUCTION Bleeder systems are that part of the mine ventilation network used to ventilate pillared areas in underground coal mines. Pillared areas are those in which pillars have been wholly or partially removed, including the areas where coal has been extracted by longwall mining. Bleeder systems protect miners from the hazards associated with methane and other gases, dusts and fumes, and oxygen deficiency that may occur in these mined-out areas. Effective bleeder systems control the air passing through the area and continuously dilute and move any methane-air mixtures and other gases, dusts, and fumes from the worked-out area away from active workings and into a return air course or to the surface of the mine. A bleeder system includes the pillared area (including the internal airflow paths), bleeder entries, bleeder connections, and all associated ventilation control devices that control the air passing through the pillared area. Bleeder entries are special air courses designed and maintained as part of the mine ventilation system. [This chapter focuses on the design, examination, maintenance, and evaluation of bleeder systems in underground coal mines.] The history of coal mine explosions in the United States is a reminder of the importance of adequate ventilation. Some of those disasters were the result of inadequately ventilated pillared areas. The importance of developing bleeder systems to ventilate these pillared areas and evaluating the bleeder system’s effectiveness is reflected in present-day federal regulations. For more information on bleeder systems, see Tisdale [1996] and Urosek and Francart [2002].

Jan 6, 2006

By Reed. Donald F.

"Deposits of gray hematite occur in two districts in Talladega County, Ala., the Emauhee-Tallasochatchee and Weewoka, both in the vicinity of Winterboro, 50 miles east of Birmingham.The deposits were investigated by the Bureau of Mines in 1943 and 1944. Approximately 13,000 feet of diamond drilling was done and 6,000 linear feet of trenches excavated and sampled.A total of 13,000,000 tons of ore averaging 36 percent iron was indicated in all areas.A detailed discussion of each property investigated, drill logs, and sampling results are given in this report.In the work done in the Talladega County iron investigation, special acknowledgement is due to Paul M. Tyler, formerly regional engineer, Eastern Region, and Richard W. Smith, formerly district engineer, for aid and direction of the project; also to J. B. Clemmor, metallurgist, for diligent research work in the Southern Experiment station laboratory. All were members of the Bureau of Mines Staff.The project was conducted in cooperation with the Federal Geological Survey, whose field work was in charge of T.G. Andrews assisted by Brewster Baldwin. The able and valuable assistance of Andrews and Baldwin aided greatly in accomplishing the project.The areas investigated by the Bureau of Mines were in two districts: The Emauhee-Tallaseehatchee district, between Sylacauga and Sycamoer (marked B on fig. 1) and the Weeworka district, between Winterboro and Sycamore (marked A on fig. 1)."

Mar 1, 1949

By D. A. Reynolds

[A few studies on the relationship of the fusion temperature of the ash of coke to that of the corresponding coal have been made on commercial high-temperature cokes. R. J. Rose3/ in 1921 compared the' fusion temperatures of the ashes of 10 coals and. the cokes produced from them and concluded tat they were in such close agreement that either figure could be used. More recently, Quarfort4/ found that the ash of coke fused at a somewhat lower temperature than that of the original coals As the ash of a coal and that of the coke produced therefrom have the same origin their chemical composition should be identical, provided that carbonization has not altered the inorganic, or ash-forming, constituents of the coal, and such alteration seems highly improbable. However, it has been shown5/ that coke is liable to contamination by iron during crushing and preparatory to sampling. Pieters6/ found that coke ash was cantaminated in this manner up to 0.4 percent. extraneous iron would lower the ash-fusion temperature because such iron may form ferrous silicate, which is readily fusible,7/ These results provide a basis for the prediction that the ash of coke will fuse at a lower temperature than that of the corresponding coil., especially if the fine grinding of the coke was done by rubbing surfaces of iron, as in a disk pulverizer or bucking plate.]

Jan 1, 1940

By J. Mitchell Linne

The principal mineral commodity in the Orleans Mountain RARE II area (No. 35019) is gold. Gravel deposits along the Salmon River contain placer gold. Lode gold with associated silver is contained in quartz veins. Many placer mining claims have been located within the study area in the Salmon River district. Four placer patents totalling 230 acres were issued for claims on the Salmon River between Lewis Creek and Forks of Salmon. On this same reach of river, adjoining and overlapping the study area boundary, approximately 3.3 million cu yd (2.5 million cu m) of gold bearing gravel with values ranging from $0.51 to nearly $5 per cu yd (50.66 to $6.50 per cu m) (gold valued at $400 per troy oz), are contained in three placers, the Bloomer, Pot Luck, and Horn (table 1). Within the study area boundary there are approximately 950,000 cu yd (726,000 cu m) of gold bearing gravel in these three placers. These three mines yielded nearly 12,000 oz (373,000 g) of gold and more than 300 oz (25,000 g) of silver between 1872 and 1913.

Jan 1, 1982

The NIOSH suite of coal mine ground control software addresses nearly every aspect of coal mine ground control planning, including geologic characterization, mine layout, pillar design, and support selection. Mine planners who use the soft-ware have access to the knowledge gained during years of NIOSH research—packaged in a simple, easy-to-use format. Several of these software packages have recently been updated and improved. Analysis of Roof Bolt Systems (ARBS) (Figure 1) helps select the proper roof bolt system design from the immense variety of available bolt types and patterns. It was developed from statistical analysis of extensive bolt performance and roof fall data. New features in Version 2 include— • The capability to analyze roof bolt systems that use two types of bolts; and • A roof support cost module that estimates the total in-stalled cost of different patterns, considering the costs of consumables, labor, maintenance, and other factors. The Support Technology Optimization Program (STOP) (Figure 2) can be used to make judgments regarding which secondary support system will be the most effective in a particular mine condition and to evaluate the advantages or dis-advantages of alternative support systems. Version 3.0 includes additional improvements: • Supports with large load-shedding following yielding can be designed based on the peak loading capability as well as the residual loading capability; • Seven new support systems have been added to the program; and • Easier access to photo gallery has been provided. The Coal Mine Roof Rating (CMRR) replaces com-plicated geologic information with a simple numerical rating that mine planners can use in many ground control applications. The CMRR can be readily integrated into a geologic exploration program, and the software package is capable of generating an AutoCAD CMRR "layer." Version 1.2 contains— • The complete CMRR database with more than 250 ratings obtained from 70 different U.S. coal seams; and • An all-new "Help" file that clearly explains all aspects of the program. Analysis of Horizontal Stress in Mining (AHSM) can help find the optimum mine layouts for control of horizontal stress. It can be used to analyze both development and longwall retreat designs, and it shows how the stress condition varies as the entry, crosscut, and panel orientations are changed. Version 2 features— • Improved graphics that enable the user to observe the effect of design changes without adjusting the display on the computer screen; and • Resource files containing information on stress map-ping, advance-and-relieve mining, stress measurements in U.S. coal mines, and other topics. [ ]

Jan 4, 2006

By E. Chin

The Asia and the Pacific region has large mineral resources of antimony, barite, bauxite, bismuth, copper, fluorspar, gold, graphite, iron ore, magnesite, mica, rare earths, salt, talc and pyrophyllite, titanium, zinc, and zirconium. The region overall lacks large resources of oil and natural gas, but it has large resources of anthracite and bituminous coal. In terms of exploitation, many minerals, metals, and fuel are produced in significant quantities in the Asia and the Pacific region as shown in table 1. Collectively, the area accounts for a substantial amount of the world production of antimony, barite, bauxite, fluorspar, gold, graphite, ilmenite and rutile, iodine, iron ore, lead, magnesite, manganese, nickel, salt, tin, tungsten, and zinc. Total coal production of the region exceeds 1.6 billion metric tons. The production of bituminous coal accounts for more than 80 % of the total output. China is the region's largest coal producer, with an output of almost 1.1 billion tons. Other major producers are Australia and India. The combined production by Australia, China, and India is more than 1.5 billion tons or 93 % of the area's output. The remainder of the coal output in the region comes from Afghanistan, Cambodia, Indonesia, Japan, the Korean peninsula, Malaysia, Mongolia, New Zealand, Pakistan, the Philippines, and Taiwan. The production of crude oil throughout the Asia and Pacific region is close to 2.4 billion barrels. China and Indonesia together account for 67 % of the total output. The remainder of the output is primarily from Australia, Brunei, India, and Malaysia. Indonesia is the largest producer of natural gas in the region with an output of close to 58 billion cubic meters, followed by Malaysia and Australia with 23 and 22 billion cubic meters, respectively. Other producers in the region of lesser stature by output include Brunei, China, India, and Pakistan.

Jan 1, 1993

This report describes the redesign, development and field demonstration of a remote shotcrete lining system, capable of operating in shafts and mines from 8 to 16 feet in diameter at depths up to 1000 feet. The original contractural scope of work outlining problems and remedial measures associated with a previous unit proved inadequate. Significant additional effort was necessary in order to fulfill the project objectives of producing a functionally reliable remote shotcrete lining system. Included with the engineering and technical description of the system, is a comprehensive technology package. Included with this material is ancillary equipment, materials selection procedures, mix-design data, quality control and assurance program, selection and training of personnel and the organizational aspects required to operate the entire system. The report concludes with details of a successfully completed borehole lining operation at the Nevada Test Site. An irregular 104 inch diameter borehole was lined at a rate of 4.8 feet per hour and 20 feet per hour respectively for 8-9 inch and a 2 to 3 inch shotcrete thickness.

Jan 1, 1983

By A. E. Harak

To determine the retorting characteristics of a column of mine-run, ungraded oil shale ranging in size from fines to 5-ton pieces, a 150-ton batch-type retort was designed and constructed at the Bureau of Mines Laramie Energy Research Center, Laramie, Wyo. The retort vessel is 45 feet high by 11 ½ feet inside diameter, and is supported in a 95-foot-high steel superstructure. Mine-run shale from the Bureau of Mines facility near Rifle, Colo., assaying about 25 gallons of oil per ton, was used as the test shale. To date, 11 runs have been completed, and the results of the last 10 of these are reported. The effects of oxygen content of the retorting gas and the superficial gas velocity of the retorting gas on oil recovery from a column of mine-run oil shale were studied. In one run, the average particle size of the shale was substantially increased to determine its effect on oil yield. Oil recoveries ranged from a low of 39.3 to a high of 65.8 volume-percent of Fischer assay.

Jan 1, 1974