Search Documents

By J. H. East, D. Harrington

"INTRODUCTION Considerable interest has been shown in the prospective use of Diesel-powered haulage equipment in both coal and non-coal mines. Foreign technical magazines have devoted considerable space to discussions of the use of Diesel locomotives in European mines and some mention of it has been made in technical papers in the United States. The Bureau of Mines has extensively tested the gases produced in the exhaust of the Diesel engine under various atmospheres and conditions of use; it has established a schedule of tests for permissibility of Diesel engines for use in underground coal mines, including, gassy or dusty mines.This publication provides information as to the successful use of Diesel-powered equipment underground workings in the United States and Europe, briefly discusses the characteristics of some of the toxic gases found in the exhaust of Diesel engines, and points out that Diesel-powered equipment can be used with reasonable safety in underground minus if necessary and entirely feasible precautions are taken."

Apr 1, 1947

By D. A. Wilson

A cyclic leaching process was developed for selectively leaching and recovering cadmium from nickel-cadmium scrap battery waste. The six major steps in the process are the following: (1) washing the plates to remove KOH electrolyte, (2) roasting at 550° to 600° C to oxidize metallic cadmium and decompose cadmium and nickel salts, (3) leaching with an ammonium nitrate solution, (4) precipitation of the leached cadmium from solution as cadmium carbonate using CO2 gas, (5) removal of CO2 from the lixiviator by adjusting to pH 4.5, heating, and evacuating the system, and (6) removal of small amounts of leached nickel from the lixiviator using a solvent extraction technique. The regenerated lixiviator is then recycled to leach additional plates. Cadmium extraction was 94 percent and the cadmium carbonate product contained 0.14 percent nickel and 0.12 percent cobalt impurity. The leached plates were smelted to a high nickel-low iron alloy with no detectable amounts of cadmium.

Jan 1, 1971

By J. R. Nettle

The purpose of these studies by the Federal Bureau of Mines was to determine the feasibility of refining low-grade hafnium by an inert-gas-shielded molten-salt electrorefining technique to produce a hafnium metal meeting reactor specifications. The techniques were adapted from those used success-fully for titanium electrorefining. Three electrolytes containing hafnium chlorides were developed from which deposits having a Brinell hardness of 170 or below were recovered. A KC1 + NaC1 + HfC14 electrolyte produced deposits in the hardness range of 140 to 165 Brinell. Deposits with a hardness range of from 132 to 152 Brinell were pro-duced from an electrolyte composed of KC1 + LiC1 + HfC14. A third electrolyte composed of NaC1 + K3HfC17 produced deposits with a hardness as low as 139 Brinell. In a fourth electrolyte, composed of NaC1 + K2HfF6, a measure of refining was accomplished, but under the test conditions no metal meeting specifications was recovered; none was softer than 174 Brinell. A number of metallic impurities were reduced in quantity by the electro-refining process, notably iron, which normally was reduced from 250 p.p.m. to less than 50 p.p.m. Magnesium generally was reduced from 680 p.p.m. to less than 80 p.p.m. Manganese content was also reduced by the electrorefining process. Sponge containing 90 p.p.m. Mn yielded deposits containing a maximum of 50 p.p.m.; some deposits contained only 10 p.p.m.

Jan 1, 1961

By J. D. Noll

Elemental carbon (EC) is used as a surrogate for regulating the exposure to diesel particulate matter (DPM) of underground metal/non-metal miners. EC was chosen as a surrogate because EC is selective to DPM and is a major component of DPM. Using EC as a surrogate also gives one the advantages of no sampling artifacts and being able to sample at all locations in the mine. Currently, EC represents DPM well in underground mines. Some control technologies have been shown to possibly alter the relationship between DPM and EC and characteristics of DPM. Therefore, future work will investigate the relationship between DPM and EC as new control technologies are implemented.

Jan 1, 2002

By Terry R. Neumann

During 1983, U.S. Bureau of Mines personnel examined mines, prospects, and mineralized zones to evaluate the mineral resources and potential of the Funeral Mountains Wilderness Study Area (WSA), Inyo County, California. Eleven mineral properties and two mineralized zones were examined during this study. Of these, six are within the study area and seven adjacent. There are no active mines, in the WSA, nor is there evidence of past production from any claim within the study area. The WSA contains no identified mineral resources. However, occurrences of bentonite, zeolites, and strontium were found in the area. There is little likelihood for resource development of any occurrence in the WSA. The area, in the Basin and Range Physiographic Province, is dominated by a Paleozoic marine sequence. Segments of Tertiary continental fluviolacustrine sediments, including volcaniclastic rocks, abut and overlie the Paleozoic rocks in fault controlled basin areas. Significant concentrations of bentonitic clay and zeolites occur as alteration products in Tertiary tuffaceous sedimentary rocks. However, they are generally low-grade, thin, and discontinuous, precluding commercial development. Limestone, quartzite, and sand and gravel in the area are suitable for many types of construction uses, but similar deposits outside the WSA are closer to markets. No energy resources have been identified in the WSA.

Jan 1, 1984

By Marcel Vanpee

Eight extinguishing powders KCI, were tested on five types of diffusion flames. The effect of flame temperature on the inhibition efficiency was investigated by varying the oxygen index of the flame supporting atmosphere. Inn addition a spectrographic investigation of powder flame dissociation products was carried out on the methane/air/ABC (NH4H2PO4) flame. Dissociation products for this flame included P0, PH, NH, and Na. It is concluded that the main factor to be considered in the efficiency of tie powder is the flame temperature Purple K (KHC03) was typically inefficient in low temperature flames and very efficient in high temperature flames. On the other hand, ABC (NH4H2PO4) was found to lose its efficiency at high temperature but to be quite efficient in the low temperature flames. The effect of temperature is offered as an explanation of the poor efficiency of Purple K (KHC03), against coal dust explosions as contrasted to the high efficiency of phosphate salts against coal dust explosions.

Jan 1, 1982

By J. D. Noll

Elemental carbon (EC) is used as a surrogate for regulating the exposure to diesel particulate matter (DPM) of underground metal/non-metal miners. EC was chosen as a surrogate because EC is selective to DPM and is a major component of DPM. Using EC as a surrogate also gives one the advantages of no sampling artifacts and being able to sample at all locations in the mine. Currently, EC represents DPM well in underground mines. Some control technologies have been shown to possibly alter the relationship between DPM and EC and characteristics of DPM. Therefore, future work will investigate the relationship between DPM and EC as new control technologies are implemented.

Jan 1, 2002

By Francis E. Federspiel

Silver and gold are the principal metals in the study area; they occur in quartz veins or silicified portions of shear zones. In some deposits, lead, antimony, zinc, and molybdenum are associated with gold and silver. A uranium-bearing buried stream channel lies near the southern boundary. Since 1850, more than 300 lode claims and relocations have been recorded mainly in the southeast corner of the study area (fig. 1). Complete mine production records are not available; however Clark (1977, p. 28) reported less than $300,000 of gold and silver were produced, mainly from the Exchequer, IXL, and Pennsylvania Mines. Other mines in the area probably yielded are before 1900, but early records are not available.

Jan 1, 1981

By John Kosek

The electrochemistry of carbon monoxide, nitric oxide and nitrogen dioxide was investigated at a variety of electrode materials in different supporting electrolytes. A portable detector for carbon monoxide was developed using a porous gold anode in perchloric acid supporting electrolyte. This detector has two full scale ranges, 0-100 ppm and 0-500 ppm. A portable detector for mixtures of nitric oxide and nitrogen dioxide was developed using a porous silver cathode in sulfuric acid supporting electrolyte. Nitrogen dioxide was determined in the gas stream by electroreduction. The nitric oxide in the gas stream was oxidized to nitrogen dioxide by passing it over Cr(VI) on firebrick. Electroreduction gave the sum of NO + N02. Analog circuitry was used to display the amounts of NO and N02 separately. Two ranges were available for each gas. They were 0-10 and 0-50 ppm for NO and 0-2 and 0-10 ppm for N02.

Jan 1, 1979

By J. G. Kirby

The total number of petroleum refineries in the United States continued to decline during 1950, and according to the Bureau of Mines annual refinery capacity survey there were 357 refineries January 1, 1951, compared with 367 a year ago. The total throughput capacity increased 267,344 barrels daily during the year to 6,963,644 barrels daily as of January 1, 1951, continuing the trend of the past several years to increase the throughput capacity of the refineries and decrease the number of plants. The capacity of the average refinery to process crude oil increased during 1950 from 18,246 barrels daily to 19,506. The Indiana-Illinois refinery district accounted for 110,175 barrels, or 41 percent of the total crude-oil capacity increase, the Oklahoma-Kansas district, 17 percent, the California district, 14 percent, the East Coast district, 13 percent, and the Louisiana Gulf Coast district, 12 percent. Slight declines ill crude-oil capacity were reported in the Texas Inland, Texas Gulf Coast, New Mexico, And Appalachian refinery districts. The 160,100 barrels of additional crude-oil capacity that was building January 1, 1951, represents an increase of 10 percent over the year earlier figure. The only completely new refinery listed as under construct ion at the beginning of 1951 is located at Superior, Wisconsin. Other new construction involves enlargement of existing refineries. Plans for at least five additional new refineries are under consideration, and construction is expected to begin during the current year.

Jan 1, 1951

By Robert Vinson

This article examines the spatial variability of dust concentrations within a coal miner?s breathing zone and the impact of sampling location at the cap lamp, nose, and lapel. Tests were conducted in the National Institute for Safety and Health Pittsburgh Research Laboratory full-scale, continuous miner gallery using three prototype personal dust monitors (PDM). The dust masses detected by the PDMs were used to calculate the percentage difference of dust mass between the cap lamp and the nose and between the lapel and the nose. The calculated percentage differences of the masses ranged from plus 12% to minus 25%. Breathing zone tests were also conducted in four underground coal mines using the torso of a mannequin to simulate a miner. Coal mine dust was sampled with multi-cyclone sampling cans mounted directly in front of the mannequin near the cap lamp, nose, and lapel. These four coal mine tests found that the spatial variability of dust levels and imprecision of the current personal sampler is a greater influence than the sampler location within the breathing zone. However, a one-sample t-test of this data did find that the overall mean value of the cap lamp/nose ratio was not significantly different than 1 (p-value = 0.21). However, when applied to the overall mean value of the lapel/nose ratio there was a significant difference from 1 (p-value < .0001). This finding is important because the lapel has always been the sampling location for coal mine dust samples. But these results suggest that the cap location is slightly more indicative of what is breathed through the nose area.

Jan 1, 2007

By Terry R. Neumann

The Olallie RARE II study area has volcanic cinder deposits with a sow potential for development. No mining claims or prospects are known within the study area, and except for common construction materials such as volcanic cinders and stone, no mineral deposits were identified. An evaluation of the geology indicates that metallic mineral deposits are unlikely to exist. No significant metallic concentrations were reported in samples from the area. The only resources in the study area are about 30 million cu yds (23 million cu m) of cinders in three cones. The cinder deposits in the study area cannot compete economically with enormous deposits of similar material in more accesible areas closer to markets. At the present rate of consumption, resources outside the area are adequate far into the future. The geothermal potential of the study area is being evaluated by the U.S. Geological Survey.

Jan 1, 1983

By Thomas M. Barczak

Wood cribs are used extensively to stabilize openings in underground coal mines. This U.S. Bureau of Mines report describes the results of full-scale testing of several multitimbered wood crib configurations. Multitimbered configurations are wood cribs that are constructed with two or more timbers per layer. Nine different crib configurations were evaluated. Configuration parameters under study included the aspect ratio (height-to-width relationship) and the percentage of solid rr:aterial used in crib construction. Test results and generalized wood crib behavior are discussed and recommendations are made concerning crib constructions to maximize strength and stability. Crib performance is enhanced by reducing buckling effects by decreasing the aspect ratio and geometry considerations that increase the moment of inertia. A cost benefit analysis of multitimbered wood crib configurations is made. Generally, increasing the percentage of solid provides more resistance at less unit construction cost. A comparison of laboratory results and underground observations of several wood pack wall supports suggest in situ load capacity is less than that measured in laboratory testing. Reasons for the apparent decrease of in situ load-bearing capability include load rate effects, stiffness of reaction surfaces, and varying boundary conditions that alter the load transfer mechanics of the crib structure.

Jan 1, 1991

By Juh W. Chen

A process for recovery of energy from waste coal fines was investigated. The process, which was developed through laboratory, bench, and pilot plant scale experiments, consists of mechanical cleaning followed by high temperature oil agglomeration and pelletization. The process can produce a quality product under an economically and environmentally acceptable condition. Waste coal fines with ash less than 35: and HHV greater than 6,000 BTU/1b have been upgraded to a product with less than 15% ash and HHV Greater than 11,500 BTU/lb. A computer model has been developed to optimize the processing costs and to perform economic evaluation of specific sites. Ultimately tine model can be utilized to establish a priority listing for a region in assisting the determination of reclamation strategy.

Jan 1, 1983

By Hon-Yim Ko

1972 constituted the second year of the projected five-year study on constitutive relations of coal. The schedule adhered closely to the five-year outline which is summarized in Table 1. This chapter is intended to serve as introduction and concise synopsis of the year&apos;s activities and results, which are presented in greater detail in the following chapters, which have been contributed by the individual researchers in charge of the various aspects of the project under study. Coal Sources, Material Procurement, and Sample Preparation Most of the studies performed during 1972 were done on coal from two sources: the Old Ben Mine #22 in Illinois, and the Bruceton Mine in the Pittsburgh seam of Pennsylvania, which may be considered typical of coal sources of economic importance in the Midwestern and Eastern part of the U.S. These two mines have proven to be reliable suppliers of coal material for our research. We have been able to establish good working relations with their personnel and feel that we can continue to count on their cooperation and help.

Jan 1, 1972

By H. R. Babitzke

The purpose of this investigation was to develop an alloy of columbium for use at high temperatures and for nuclear applications. The properties of possible alloys were determined, and the more promising ones were selected for further improvement. Criteria for selection were machinability, hardness, workability, tensile strength, and oxidation resistance. Thirteen 100-gram ingots, ranging from 100 percent columbium to 100 percent vanadium, were prepared and subjected to various tests. Also included for comparison were zirconium and the zirconium alloy, zircaloy-2. Test results showed that a columbium alloy, containing 10 atomic percent vanadium merits further development. Besides being workable at room temperature, the columbium-10 atomic percent vanadium alloy has oxidation resistance superior to the other alloys of the series and is also superior to zirconium or zircaloy-2. The latter two materials have comparable neutron-absorption cross sections. The strength and hardness values of the alloys tested were found to increase with increasing vanadium content, reaching a maximum at 50 atomic percent vanadium and decreasing with further increase in vanadium. This behavior is typical of binary alloys wherein each element will retain any proportion of the other in solid solution. INTRODUCTION There is an increasing need for alloys for service at high temperatures. Since current world reserves of columbium metal approximate 1,500,000 tons (1),4 this metal is now readily available. Columbium can ties; be considered a practical base material for high-temperature alloys required in nuclear reactors and in aircraft and space vehicles. General requirements chosen are: (1) Workability, (2) satisfactory mechanical properties at temperatures approaching 1,000° C., and (3) resistance to oxidation at such temperatures.

Jan 1, 1962

By J. F. Neill, O&apos

The manganiferous schists occurring in the vicinity of Kings Mountain, North and South Carolina, suggest significant tonnages of potential submarginal ores. Although some reconnaissance work in connection with these deposits has been reported, no recent information has been published. Evaluation of the schists as a possible domestic manganese resource has not always adequately considered the fact that the manganese content occurs quantitatively both as oxide and as the silicate, spessartite. The Bureau of Mines investigation herein reported includes preliminary studies to indicate the extent of manganese oxide mineralization and to deter-mine the amenability of the material to sulfur dioxide leaching. The field reconnaissance studies suggest a resource containing in one area an average of 6.4 percent manganese as oxide. The procurement of depth information was beyond the scope of the investigation.

Jan 1, 1962

By M. Karmis

Surface subsidence is an inevitable consequence of many underground mining operations and has been recognized as such since the fifteenth century. Damage resulting from this phenomenon ranges from simple land settlement to severe structural damage to buildings and has been witnessed in rural (Illinois, Colorado, West Virginia, Virginia, Pennsylvania) as well as in urban areas (Pennsylvania, West Virginia, Illinois, Wyoming). In fact, it is estimated that over 2 million acres of land across the United States have been affected by mining subsidence, of which 140,000 acres are in urban areas (Singh, 1978; Johnson and Miller, 1979). Further, it is estimated that during the next twenty years an additional 1.5 to 2.4 million acres of land will also be affected by mining. Subsidence prevention is not feasible, at least under the existing technologic and economic constraints of underground coal mining. Foreign experience has demonstrated, however, that subsidence can be successfully controlled if an accurate method of predicting ground movements is available. Such techniques have been developed in many coalfields, where it is currently accepted that subsidence can be predicted within ± 20 percent of the actual values. Furthermore, such movements can be translated into anticipated structural failures using established damage criteria, thus enabling appropriate precautionary measures to be implemented.

Jan 1, 1983

The selective placement of coal stripmine overburden is examined. Physical and chemical properties of spoil detrimental to revegetation and groundwater are detailed. The United States is divided into regions or similar problems. Five mining methods already used in the industry, that are capable of selectively handling waste are examined in detail. Technical and economic comparisons are made for the systems when applied to realistic mine settings. The same analysis is conducted for five novel methods capable of selectively handling waste. Comparisons are made between novel and existing methods. Suggestions for new and modified equipment are outlined. Recommendations for further research are provided. This volume contains all Appendices to the report.

Jan 1, 1981

By L. D. Schmidt, W. C. Schroeder, A. C. Fieldner

"INTRODUCTION The highly mechanized character of modern warfare makes steel the most vital raw material. The shortage of steel scrap in the United States is forcing the use of increased quantities of pig iron in steel manufacture, so that the rate of pig-iron output will continue to be the controlling factor in steel production. 5/ At the same time, the construction of new blast furnaces is limited both by time and the amount of strategic material available. Under such circumstances, every effort must be made to attain and then maintain maximum pig-iron output from the equipment now in use.When forcing a blast furnace to the ultimate in production the highest standards for quality and uniformity of the coke must be maintained. In view of these facts, the Bureau of Mines, in cooperation with the Office of the Solid Fuels Coordinator for War, is surveying the coke industry to study the various steps in producing coke of higher quality and greater uniformity. 6/ The engineers conducting the survey are visiting key men in coke-oven and blast-furnace organizations to determine, first, the major and most common problems in coke production and use; and, second, the best and quickest method for solving them. Various operators have made good progress in solving individual problems, and a Nation-wide exchange of information among them will make possible widespread adoption of the best practices. It is the purpose, of the survey and reports such as this preliminary one to facilitate such exchange of information. As an outgrowth of the survey, it was soon revealed that many operators could be helped by cooperation with various Government agencies, particularly to procure suitable coals, minor additions to equipment facilities, and tests on certain properties of coal or coke, or specific advice concerning the operation of various types of equipment. The machinery and organization necessary for securing this cooperation have been set up as a part of this work."

May 1, 1943