Search Documents

By J MacPhail, H Gardner

This paper discusses reasons why users of rotary air blast hole bits encounter premature bit failure due to bearing failure. It also discusses a lubrication system designed for rotary rock bits to combat bearing failure.

Jan 1, 1996

By Richard B. O'Meara

"The demand by a customer to an Explosives supplier to fulfill a specialised productrequirement was met by a level headed decision to try to satisfy that demand. This paperwill describe the fundamental steps required in order to develop and produce a newexplosives device, while under certain resource constraints, such that the needs of thecustomer and the supplier are met safely and effectively."

Jan 1, 1993

By A T. Spathis, J J. Felice, W Klass

Cast blasting has become one of the most efficient ways to move waste rock in open cut coal mining. It is used at Mount Thorley Mine in conjunction with a dragline to move some of the overburden onto the spoil dump.

Jan 1, 1992

By He Guangyi

During rock blasting in extending deep cutting from Jiu Li Mountain to Dong Zhuang Village in Jiao Zhi Railway line, we have drilled deep hole with large scale diving drilling machine and successfully carried on controlled blasting. This has provided new experiences for rock blasting in extending existing cutting. The aim of this article is to provide an introduction to bench height, blast holes arrangement, powder charge calculation, and detonating technique during blasting.

Jan 1, 1997

By Doug Hoy

The scope of the Cliff Avenue Reconstruction Project in Sioux Falls, South Dakota was to widen a two lane highway to five lanes, along with removing and reconstructing both above and below ground utilities located along the project limits. The objective of this paper is to present the blasting techniques used in the rock excavation phase of the Cliff Avenue Reconstruction Project.

Jan 1, 1992

By T Guiliani, F Ottuonye

Explosives casting is gaining increasing popularity as an overburden removal method in strip mining because the coats of using explosives to cast a percentage of the overburden to the spoil are lower than the costs of using stripping shovels or draglines to do all the overburden removal. This is due to the rising capital and operating costs of draglines and shovels.

Jan 1, 1989

By Michael Beattie

A large open-cast limestone mine had its blasting operations severely restricted by the imposition of limiting PPV levels to protect a water pipe-line passing through the mine property. Attempts were made to measure the strains induced in the pipe by ground vibrations, so that a less restrictive blasting limitation could be established on a scientific basis.

Jan 1, 1992

By G Alan Foster

Because of the marked human response to blast effects and inherent defects present in many modern structures the real possibility of being named as a defendant in a law suit faces most blasters. Until recently even frivolous law suits involved a great deal of expense since legal costs were inevitably incurred whilst waiting for your day in court, which typically occurred some 2-4 years after the alleged damage took place.

Jan 1, 1989

By Mark Odell, Bruce Northrup

In the hill country of Austin, Texas, Tom Kite has designed a golf course to be built in conjunction with a housing development entitled "Riverplace". The topography in this area is almost solid limestone, which made it necessary to use several types of surface blasting: Pre-splitting, ditch-line, sump shots, not to mention "fairway" cuts and even a sand trap or two.

Jan 1, 1985

By James E. Jr Hargroves

With the ever-increasing population growth and modern trend to urban development, the expansion of utilities is a stable, mad or, and constant source of income for many. Blasting is a "necessary evil" to the utility contractor. It can make or break even the most solvent. Housing development expansion and higher treatment of effluents are causing utilities to appear in more congested areas. This paper discusses some of the aspects of utility blasting in the State of Virginia. Consideration is given to bid procedures, pre-blast surveys, record-keeping and practical application.

Jan 1, 1977

By Wang Xuguang Shen Yingfeng

Structure is the main aspect affecting the performance of emulsion explosive. Calculation of such structure parameters as osmosis pressure, interface area per unit volume etc. must be helpful to the understanding of the structure of emulsion explosive. This paper has solved the Laplace-Young Equation for simplified monodisperse emulsion system by Galerkin method, and gained the relationship between mean curvature, contact angle, volume fraction, fractional film area and interface area per unit volume. The paper also presents a new expression of osmosis pressure at non zero contact angle.

Jan 1, 1998

By George D. Raitt, Rudy Lyon

Until fairly recently, Down-The-Hole (DTH or DHD) hammer drilling was never really a factor in large scale open pit surface mining. It was a method confined to water well drillers, aggregate quarries and limestone mines where the hole size rarely exceeded 6-1/2" (165 mm). Also it was somewhat limited to the harder rock areas such as the North East and South East United States. The trend in the big mining pits for coal, copper, gold and iron, was for the big rotary drill rigs with lots of muscle in pulldown, bitload and rotary torque.

Jan 1, 1998

By Jack Eloranta

This paper documents the relationship between material handling and processing costs compared to blasting cost. The old adage, "The cheapest crushing is done in the pit", appears accurate in this case study. Comparison of the accumulated cost of: powder, selected wear materials and electricity; indicate a strong, inverse correlation with powder factor (lbs powder/long ton of rock). In this case, the increased powder cost is more than offset by electrical savings alone.

Jan 1, 1995

By Yang Ruilin

Bulk gassing technology is a growing trend in the commercial explosive industry. The gassed bulk products produced differ from microballooned bulk products or cartridged products. It is easy to know the loaded or in-hole density for microballooned bulk products or cartridged products, whereas it is not as straight forward to know the m-hole density for gassed bulk emulsions. The loaded density is one of the key parameters affecting explosive performance and therefore it is important to have a field technique to monitor the in-hole properties of gassed bulk products in order to accurately predict the blast performance and to ensure efficient use of the products.

Jan 1, 1999

By Robert Hopler

Accidents associated with the storage of explosives prompted regulating the locations of such storage at least as early as 1719, when an act was passed in Great Britain. During the following years various refinements to the regulations were made, but a major explosion in 1864 in which there was destruction and loss of life as far away as 10 miles, led to the landmark Explosives Act of 1875. This act certainly had influence on regulators in the United States: when Massachusetts established an explosives distance/weight table in 1904 they referred to the prior British work. Later, Colonel Dunn of The American Railway Association convened a conference of explosives manufacturers to discuss safe storage. From this conference the American Table of Distances was established in December, 1910.

Jan 1, 2007

By Mark S. Stagg, Stephen A. Rholl, Steven G. Grannes

A method of determining the fragment size distribution of rock quarry muckpiles using photographic and digital-image processing techniques has been developed by the Bureau of Mines. To assess the fragmentation, photographs and video tapes were taken in both the laboratory and in the field and then digitized for analysis. The fully-automated process uses specially written image-interpretation software which had been developed previously by Bureau researchers to measure irregular taconite ore shapes. The advantages of photographic assessment in comparison with other methods include speed and cost.

Jan 1, 1993

By Justus Deen, Paul Sterk

Overbreak into the wall rock of a development drift leads to the inevitable need to rehabilitate a drift. Moreover, overbreak in a production heading can lead to external dilution and lower ore grades. Both of these factors are critical to bottom line costs of underground operations today. The geology of the Homestake orebody makes this an even more complex problem. For over fifteen years the Homestake Mine has attempted to implement perimeter blasting techniques that are both safe and cost effective. Many practical perimeter methods and products have been tested including air decking; low density emulsions; various types of stick powder; various decoupling media including rope, low density ANFO, polystyrene ANFO, salt based ANFO, and various grain detonating cords up to 200 grain.

Jan 1, 1997

By Gordon Revey

In construction and mining work, situations occasionally occur where hard rock or concrete must be excavated at locations near critical structures or utilities. Fearing damage from blasting, contractors and engineers often explore the viability of using mechanical methods or expansive concrete to facilitate the excavation work. However, for moderate to large excavations, the prolonged duration and high cost of using these methods is often impractical. In these situations, under the right conditions, controlled blasting and blast-management methods can be used to speed up the work and lessen costs. The process of determining whether or not blasting is practical is ofien complex, particularly when risks are high.

Jan 1, 2001

By Wesley L. Bender, James E. Murray

Pre-blast surveys are often conducted solely to document existing structural conditions and uncover potential problem areas. This paper presents a case history where the pre-blast survey was also used as a vehicle to initiate a public relations program with the occupants of a large apartment complex adjacent to a major excavation site. The public relations program, in conjunction with good blasting practices, succeeded in keeping complaints to a minimum. The presentation includes an overview of the project, details of the public relations program, some of the blasting methods that were utilized and a recap of the complaints received.

Jan 1, 1988

By Joseph Trocino, John Anderson, Stephen Murray

This paper describes the development of LEXFOAM® (Liquid EXplosive FOAM) as a unique low density explosive, and its successful application as an effective tool for "in-place" demolition of landmines and unexploded ordnance. Explosives research using aerosol technology led to the development of LEXFOAM whose components are safely transported and stored as flammable liquids. These components are mixed on site to produce an explosive foam, which enhances safety and minimizes logistical problems. Hand-held, Backpack and Palletized Delivery Systems form a versatile family of dispensing systems to suit any application.

Jan 1, 1998