Search Documents

By M. Vasudevan

In sulfide mineral flotation, the efficiency of separation is severely affected by the presence of non-sulfide gangue minerals, such as altered silicates and serpentines. Although this is an acknowledged fact, most studies in mineral processing have focused on value minerals, and studies on gangue minerals affecting flotation performance are quite rare, and even those that do are limited in scope. This paper is an attempt to highlight the use of grade-recovery curves in studying the effects of gangue minerals. Specifically, we present the flotation response of problematic Ni and Cu ores which show highly uncharacteristic but similar grade-recovery characteristics despite the very different mineralogy and try to understand this behavior and the underlying mechanism. Finally, we propose chemical modifiers as solutions to overcome the detrimental effects of these gangue minerals and improve efficiency of flotation performance. Keywords: Non-sulfide gangue, grade-recovery, sulfide minerals, serpentines, talc, shale, slimes, spiking, modifiers

Sep 1, 2012

By Xiaoming Wang

This paper presents an arcuate magnetic separator to remove the grinding ball fragment directly from the mill discharge, which will cause wear to downstream processing equipment such as pump, hydro cyclones and pebble crusher. Furth more this type separator was applied in Wushan mine under China National Group Corporation in China. After months of operation, the equipment has been a success. It removes majority of ball fragments from mill discharge. Keywords: magnetic separator, sag mill, pebble crusher, grinding ball fragments

Sep 1, 2012

Low-grade ore bodies, increase in rock competency, finely disseminated valuable minerals in the ore bodies, ore variability and water scarcity are among the technical challenges faced by the mining industry. These challenges have increased the business risk, capital investment and operating cost of the mining projects. Since the last 20 years, many large-scale concentrators have been built to cope with the above-mentioned challenges. Comminution, especially the fine grinding is an energy-intensive process. For example, the ball mill has a limitation in the fine grinding regime where the energy consumption increases exponentially when the product size is below 45 µm. The industry has been seeking for solutions that have a minimum risk and total cost of ownership. The stirred milling technology such as the TowerMill is well accepted by the industry as it has demonstrated the attributes required for fine grinding. TowerMill is a matured technology that has been adopted since the 80s for regrinding duty. Recently, this technology was installed in secondary and tertiary grinding duty to prepare a finer feed to rougher flotation. Four units of TowerMills were installed in a magnetite concentrator in Western Australia in tertiary grinding duty. Recently, Nippon Eirich has conducted process performance evaluation on the TowerMill circuit. The outcome of the exercise had indicated that the circuit is consuming 3.4 kWh/t to reduce from 55 µm to 35 µm with a narrow product size distribution. The effect of operating variables such as the specific energy, grinding media size, mill content % solids and mill feed configuration on the grinding efficiency were evaluated at the plant scale. Furthermore, the scale-up methodology was validated. The scope of this paper includes the performances of TowerMill and the validation of scale-up methodology.

Jan 1, 2018

By Heiko Schiemann, Christoph Beyer, Thomas Pretz

"Due to multiple experiences in the field of planning and engineering of processing plants for secondary materials the Chair for Processing and Recycling of Solid Waste Materials decided to develop a software tool that supports the engineering and the planning of the basic layout of processing plants for secondary material flows. The detailed description of the material flow and its characteristic parameters is one of the main tasks to be worked out and should be considered as the basis for representative simulation results.The description of the material flow and its characteristic parameters is based on a fraction vector containing 12 material fractions. This is a compromise between a detailed material flow description and a compact and therefore time-extensive calculation model. Each material fraction is characterized by 15 parameters, which can be edited with the help of an easily accessible user-interface. In addition to basic parameters like ignition loss, water content and calorific value more parameters like the material fraction-specific particle-size distribution are contained. Using the model library SimuRec, the processing success and the recovery of complex processing plants for secondary materials can be predicted."

Jan 1, 2003

By S. Q. Zhu

A newly developed coal flotation collector ZFC and its flotation characteristics for five different coals were introduced in this paper. ZFC is an emulsion composed of 27% diesel oil, 70% water and 3% surfactants. The main surfactant is synthesized with oil which is environmental favorable and reproducible. Compared flotation experiments show that, at the same dosage, ZFC give 2%~5% recovery promotion than typical collector with only a slightly ash content increment, but saving 70% diesel oil. Zeta-potential and Wetting heat measurement indicate that the surfactant helps the interactions between oil and coal particles, the industrial application tests in several coal preparation plants demonstrate that ZFC is suitable both in technical and economical aspects.

Jan 1, 2014

By Áureo Del Vecchio, Lídia Dely Alves de Sousa, José Pereira

The potassium demand for agriculture purposes has increased in Brazil, which has great deficit of internal demands. Potassium-rich rocks have been used as fertilizers as technological alternatives for agriculture aimed to reduce the amount of chemicals and the sector dependence for such products. Vermiculite tailings from União Brasileira de Mineração - UBM, at Santa Luzia - PB, was studied aiming their application in agriculture by potassium release. The sample was analyzed by XRF and XRD; studies on release kinetic with particles smaller than 2 mm added of organic acids (citric and oxalic) at 10-2 mol/L concentration; samples were analyzed by XRD after kinetic assays. The work was conducted using a shaker incubator at 300-rpm agitation and time variation to better understand the potassium availability in the ground. Results show the presence of K2O at 3.46% concentration. Citric and oxalic acids increased the release speed to almost the same level with speed coefficients (k) of 2.61x10-2 h-1/2 and 2.55x10-2 h-1/2 respectively. In statistical terms for both acids, the linear equation represents more than 99.0% of the experimental assays. Stonemeal was applied to banana seedlings in experiment conducted in a greenhouse. The use of vermiculite tailings in banana seedlings promoted potassium absorption, which influenced its growth. The amount of potassium liberated from vermiculite tailings could be used as a long-term alternative to fertilizers in agriculture cultures.

Jan 1, 2014

By William Conger, Greg Schick

Grinding media consumption is a major cost variable in industrial mineral comminution circuits. Specifically, industrial SAG media consumption results from a combination of surface abrasion wear, media breakage, surface spalling and rejection size from the mill. Three main consumption rates; weight of media consumed per time, per kWh and per weight of ore ground are defined and compared. Recent industrial data has provided an opportunity to relate consumption in terms of weight of media consumed to weight of ore ground (g/tonne) and weight of media consumed per kWh of energy consumed (g/kWh) with SAG specific grinding energy consumed (kWh/tonne). Using relationships developed from this data it is possible to project SAG media consumption in future mineral comminution circuits.

Jan 1, 2014

By A. P. Das

Biomining technology focuses on achieving effective recovery of precious metals from their ores and concentrates using microbial techniques. Biomineral extraction of manganese from low-grade manganese ores using bioleaching was investigated in this paper. Five fungal strains were selected for screening of bioleaching of low-grade Mn ore collected from Sanindpur iron and manganese mines, Koira Sector, Keonjhar, Odisha, India. A fungal strain, Aspergillus niger was selected as it showed high efficiency of manganese leaching. Growth of the fungus was determined in terms of sbiomass dry weight and the final pH was monitored. The selected fungal strain was used for bioleaching of low-grade manganese ore of -150µm size particle size at 2 % pulp density with 2g/100ml sucrose concentration for duration of 20 days. About 60 % of Mn bioleaching was obtained with A. niger. The fungal species proved to be useful for manganese biomining.

Sep 1, 2012

By Grant C. Lukey, Jannie S. J. van Deventer

"The environmental effects of the mining and mineral industry include destruction of natural habitats, changes in river regimes and water tables, and other serious ecological impacts. In this century, it is likely that water will become a critical resource, and in most countries the mining industry competes for a share of this resource. The Kyoto Protocol may at first seem only relevant to the coal mining and power industry, however, it should not be forgotten that the mining and mineral industry is a significant consumer of power. Therefore the ratification of the Kyoto Protocol by most developed countries and the introduction of a carbon credit trading scheme will impact on the industry by potentially increased costs in utilities and waste discharges. It is clear therefore that the mining industry faces many challenges in the coming years. The mining industry?s commitment to sustainable development needs to continue to evolve, in order to meet these challenges effectively. With the advent of globalisation of the industry, it is now an opportune time for the industry to gain international agreement on how they want the industry to achieve sustainability in future years; such a progressive approach is necessary, otherwise government will force the industry to change, which may not necessarily be the best outcome for the industry.INTRODUCTIONThe Earth Summit in Rio de Janeiro in 1992 was an opportunity for world leaders to assemble and discuss strategies and initiatives that provide for further industrial growth without adverse effects on the environment. The World Summit on Sustainable Development held last year in Johannesburg, South Africa, was an opportunity to evaluate those initiatives implemented over the past 10 years, and to set a new and sustainable direction for the future. It is clear that industrial and technology development will continue at a rapid pace in order to serve the needs of a growing world population, but it is essential that the course of this development is well planned, well executed, and that it is sustainable. In reality, while government officials and politicians continue to debate policy and international protocols, the environment continues to suffer and the effects of climate change and global-warming become more real each day."

Jan 1, 2003

By Kazutoshi Haga, Batnasan Altansukh, Atsushi Shibayama

Results of flotation process combined with atmospheric leaching and high pressure leaching for recovery of copper from low-grade silicate-copper ore have been presented in this study. The low-grade copper ore contains a small amount of copper (0.42 mass %), iron (4.6 mass %), and silicon (38.3 mass%) and among many other metals (Al, Ca, K, Mg, Na, Ti and S). The main mineralogical constituents of the copper ore are calcium aluminosilicate (Ca(Al2Si2O8), amesite (Mg2Al2SiO5(OH)4) and gypsum (CaSO4×H2O), and quartz (SiO2) as resulted from the alteration of an igneous rock. This study has shown that about 92 % of copper can be recovered with a maximum copper grade of 4.2 mass% in a froth after 15 minutes of flotation at pH 8.5 when used potassium amyl xanthate as a collector, MIBC and Dow-froth 250 as frothers and calcium hydroxide as a pH adjuster. The images of bubbles in the cell during flotation process were recorded using a high-speed camera. The froth concentrate with average copper grade of 2.0 mass% was further processed by atmospheric leaching with a solution of sulphuric acid and hydrochloric acid, respectively and high pressure leaching with sulphuric acid solution. As a result, leaching rate of copper reached about 60 % in an atmospheric leaching with sulphuric and hydrochloric acid respectively, whereas the rate can reach more than 70 % by autoclave leaching at high pressure under the controlled condition. A process to recover of copper from its low-grade ore can be developed by optimization of flotation combined with acid leaching.

Jan 1, 2014

By Gustav Hawlitschek, Henrique Kahn, Carina Ulsen, Renato Contessotto

"The problems related to waste dumping increased with the growth and development of large cities. In the U.K., more than 50% of landfill waste comes from construction use and the U.S. alone produces around 200 to 300 million tons of CDW annually. The exhaustion of natural sand deposits close to large urban centres stimulates the recycling of construction and demolition waste for the production of recycled aggregates as a construction material. This paper presents a flowchart for the production of recycled sand with low porosity and regular shape by the selective removal of the cement paste attached to recycled aggregates. The products characterization was carried out by the determination of the particle size and shape distribution, chemical and mineralogical composition, heavy liquid mineral separation and quantification of all present phases using a scanning electron microscopy with automated image analysis (SEM-MLA). The comminution of CDW by vertical shaft impact crusher made possible the production of a lower porosity recycled sand. The heavy liquid mineral separation showed that the proportion of low porous phases (d>2.5 g/cm3) is very high, exceeding 70% of the weight, encouraging further mineral processing separation to obtain a fine recycled aggregate with less cement paste content. The mineralogical characterization by XRD and SEM indicates that the main phases are tectosilicates, phyllosilicates and calcite which one can be attributed to both calcareous aggregate and cement paste. The precise quantification of cement paste and calcite/dolomite alone is just possible by automated image analysis. The characterization results demonstrated that proportion of phases with no cement paste attached increases progressively in denser products. The results of heavy liquid separations and image analysis are comparable and automated image analysis can be used for the characterization of phase content and their main associations."

Jan 1, 2014

By Robert van Hille, Alison Lewis

The precipitation of a selection of metals from both a synthetic and an actual metal-rich effluent was investigated. The experimental aspects of this study were carried out in a two-stage process consisting of a pre-treatment clarifier and a fluidised bed (pellet) reactor. Each unit operation in the two-stage process was investigated separately. The pre-treatment clarification stage at pH ˜ 5 resulted in a 99.9% removal of iron and 97.3% removal of aluminium. The pellet reactor was used to precipitate nickel as nickel carbonate from a pure stream and a removal efficiency of 99.6% was achieved. The high local supersaturation at the reagent inlet points caused the formation of a large amount of fines, but these agglomerated onto the pellets up the length of the bed. For copper precipitated as copper sulphide from a pure stream, a maximum removal efficiency of 92% was achieved. The high local supersaturation at the reagent inlets also caused the formation of a large amount of fines, but the extremely sparingly soluble nature of copper sulphide meant that the fines were not agglomerated up the length of the bed. For removal of cobalt as cobalt carbonate from an actual stream, a stable cobalt removal of only 60% was achieved. This was found to be due to the presence of magnesium, which reduced the cobalt precipitation efficiency through the formation of the magnesium bicarbonate ion.

Jan 1, 2003

By M. Nonaka

An attempt to produce fuel from biomass waste by hydrothermal treatment has been made with expectation to effectively utilize a renewable source of energy and an unexploited energy resource. In this paper, we have used empty fruit bunch (EFB) that is a residue after recovery of crude palm oil from palm oil trees in a plantation in a tropic country. A hydrothermal treatment was conducted using a 500 mL autoclave, with alkali (K2CO3) catalyst. EFB was decomposed more by alkali catalyst of lower alkali content and rather polymerized in higher catalytic region. The functional group composition of the solid phase oil is similar independent of alkali content, however its burning characteristic became more incombustible with increasing alkali content.

Jan 1, 2014

By Josefin Lannefors, Anders Klingberg, Natalija Gorochovceva

"Development of new anionic collectors becomes more and more important. This can be explained, on the one hand, by the fact that over the years phosphate ores have become more fine grained and complex (example weathered). On the other hand, a development with a focus on sustainability (sustainable development) of new anionic surfactants is required by authorities and society. Within the sustainable development several characteristics of a collector have to be taken into an account: efficiency, selectivity, froth characteristics, environmental profile, raw materials used for the synthesis, manufacturing complexity, stability upon storage, etc.Several anionic surfactants based on ester and amide chemistry were synthesized, characterized and used as flotation agents for calcium phosphate containing ore. The surfactants were used in a formulation together with other anionics, since in a pure form, during the flotation, they did not provide right froth characteristics.A new anionic collector/formulation was developed, that fulfills all above listed requirements."

Jan 1, 2014

By Silvia França, Hudson Couto

"In this paper, an alternative beneficiation process was developed to recover nickel minerals from low-grade weathered ores. The studied sample, 0.3% Ni grade, is essentially composed of nickel sulfides (pyrrhotite and pentlandite); magnetite and silicates (mostly talc and amphibolites) are the primary gangue minerals. The particle size distribution was controlled using a grinding operation to avoid producing an excess of fine particles by overgrinding. The sample underwent a grinding step for the fine degree of liberation. The slimes (-20 ?m) were removed via two desliming stages in hydrocyclones (diameters of 1.5" and 2"); the ground material, which was classified in a range of (-150+20) ?m, was processed by column flotation in three different stages: rougher flotation for magnesium silicates, rougher flotation for sulfides, and cleaner flotation for sulfides, using pilot flotation columns (2" and 6" in diameter and 20 ft high). The goal of using the preliminary magnesium silicate flotation step was to remove hydrophobic minerals (mostly talc) that would float naturally with the sulfides, which would decrease the Ni grade in the concentrate, as well as to reduce the MgO content because this compound is considered harmful in metallurgical processes when a grade greater than 9% is used. The final concentrate obtained in the cleaner flotation step reached up to 2% Ni and 7.0% MgO. The global and flotation recoveries in the process were approximately 30% and 60%, respectively, due to the losses of Ni during the desliming process. Despite this low global recovery, the adopted beneficiation process can be considered an interesting alternative to produce nickel concentrate from tailings or waste materials."

Jan 1, 2014

By Vishal Shukla, Ashok Kumar, C. Raghu Kumar, D. P. Chakraborty

"Traditional iron ore beneficiation plants using washing, screening, and jigging processes require large volumes of process water. Generated slime during processing, its disposal and impact on water usage, is an important concern for any mining company. The challenge today, during extracting iron ore, is how to dispose of slime such that it is contained and stable, while maximizing water reuse and minimizing surface footprint. The slime disposal methods are sensitive to the environment. Two major technologies presently being practiced for disposing the slime across the world are pressure filtration and paste thickening. In this perspective an attempt has been made to do comparative study between paste thickening and pressure filtration for selection of suitable slime disposable technology for Noamundi processing plant, Tata Steel. From the studies, it is evident that by adopting pressure filtration technique it was possible to produce filtered slime, whereas filtration, rate reduces significantly with the presence of finer fraction. Further , the greatest advantage of paste thickening is volume reduction of slime. By considering the technology limitation and comparative lab test work result, it is opined that combination of filtration and paste thickening technology is favorable in terms of capital and operating cost and slime >45 µ should be filtered and < 45 µ slime should go for paste thickening. The study and the results are presented in details.INTRODUCTION The beneficiation processes always end up with an enriched portion of desired mineral - “Concentrate” and an enriched portion of undesired minerals - “Tailing”. The proportion and nature of tailings generated in every beneficiation process differ from ore to ore and reflects the characteristics of the feed processed. The traditional method of tailing disposal in many mineral processing industries has been to dispose them as thickener underflow at around 35% solids. Though, it had certain advantages of transportation with ease but contribute to a greater volume occupied in the tailing dam. This sustained practice and failure to utilize the space available in the tailing dam judiciously endangered the mining industry. The tailing management has become the toughest task to the mining industry and most of the mines are running out of space for disposing the fresh tailings as many of these are at the verge of getting filled."

Jan 1, 2018

By D. R. Nagaraj, Raymond Farinato

Water constitutes one of the most valuable resources employed in mineral recovery and processing. Identifying potential problems encountered in mineral processing in waters unusable for drinking or agriculture (including seawater and even hypersaline waters), understanding chemical factor interactions, and optimization of flotation reagents will greatly expand our ability to create more sustainable beneficiation technologies. The current paucity of our knowledgebase regarding high salinity effects on flotation clearly signals a need for a significant research effort. We report here results of a study designed to probe effects of pulp chemistry on metallurgical performance in the flotation of Cu and Cu-Mo ores in saline waters. The results clearly demonstrate that pH (more correctly dosage of pH modifier to target a pH set point) has the most significant effect on Mo recovery when using seawater. This is linked to the formation/precipitation of Mg(OH)2 when pH = 10.3 (in seawater). The type of pH modifier used, NaOH or Ca(OH)2, had no impact on Cu or Mo recovery, indicating that Ca2+ ions were not involved in any reduction in Mo recovery in the pH range of 9-11. Our results in tap water spiked with either Ca2+ or Mg2+ ions in the same pH range (controlled by NaOH), confirmed that Ca2+ ions had no effect on Cu or Mo recovery, but that addition of Mg2+ ions had a severe adverse effect on Mo recovery at pH = 9.5, and to a lesser extent on Cu recovery. The onset of Mg(OH)2 precipitation occurred at a higher pH, and the adverse impact of Mg(OH)2 on Cu recovery (and perhaps Mo recovery as well) was less, in sea water than in tap water spiked with Mg2+. These effects are attributed to the mitigating role of the high electrolyte concentration, notably NaCl.

Jan 1, 2014

By R. K. K. Mbaya

The concept of adsorption or separation of platinum anions from base metal cations in chloride media using native or chemically modified activated carbons has been discussed in various journals within the context of batchwise systems. In our research work, a fixed-bed column, loaded with native and amine-immobilized activated carbon pellets (Norit RO 0.8), was used to study selective adsorption of platinum ions from chloride media at different flow rates, bed depth and initial metal concentrations. The kinetics, mass transfer characteristics, breakthrough data and separation factors (ß(Pt/Fe) and ß(Pt/Cr)) were quantitatively analysed and modeled. The bed-depth service time (BDST) model was used to model the breakthrough curves successfully in fixed-bed columns and also the dispersive diffusion in the radial and axial directions of the bed were evaluated. The inner diameter of the column was 3 cm and the bed depth was between 1.0 cm and 2.5 cm. Concentrated 4 M HCl acid solution was used to elute the fixed-bed column. It was demonstrated that amine-treated activated carbons provides superior separation factors between platinum and base metals (Fe, Cr). Results showed also, that 95% saturation was reached within 10~26 hours depending on the nature of ACs at a flow rate of 11 mL/min and initial concentration of 5 ppm.

Jan 1, 2014

By William Skinner, Jonas Addai-Mensah, Keith Quast, David Robinson, Jason Connor

A review of the laboratory- and pilot plant-scale physical separation techniques for the beneficiation of nickel (Ni) laterites shows limited efficacy. To date, the only upgrade technique adopted commercially, prior to hydrometallurgical processing of Ni laterites, is the removal of a barren, coarse size fraction in the feed by classification. In the present work we investigated two low grade (~ 1%), goethite-rich Ni laterite ores’ upgrading by magnetic separation, attritioning/coarse, (lower Ni-grade) gangue rejection and flotation techniques. Low intensity (0.1T) dry magnetic separation at ambient temperature of raw samples and those pre-heated at temperatures up to 450 °C showed evidence of pay metal Co and Mn bearing asbolane and/or lithiophorite minerals pre-concentration in the magnetic fractions. Ni distribution, however, did not show any noticeable magnetic upgrade but followed the weight distribution. Other ore pre-treatment methods (e.g., desliming and sulphidisation) followed by froth flotation with anionic and cationic reagents also led to noticeable (~35%) Ni upgrade. This is due to the deportment of Ni across several gangue host mineral phases (i.e. Fe oxide/hydroxide and a range of silicate/aluminosilicate minerals). From chemical analysis, after disaggregation of ~ 1% Ni grade feed ore, coarse (-600 + 38 µm) and fine (-38 µm) fractions of ~0.6% and 1.3% Ni grades respectively, were also produced, suggesting that a significant upgrade in Ni content can be achieved by rejecting the + 38 µm fraction with the loss of <40% of the Ni. The ore mineralogy, particularly the complexity and high number of un-liberated Ni-bearing phases, greatly compromises physical separation methods for these ores, with the possible exception of screening after disaggregation of the fines inherent in the run of mine ores.

Jan 1, 2014

By F. Bello, J. Engels

"During 2012 and 2013, Minera Esperanza conducted a series of thickening and deposition trials to identify design and operational parameters associated with increased thickening of its tailings. These trials focused on benchmarking the current solids concentration of tailings (62 - 64%) in anticipation of an increase to 67% solids once two new 45 m diameter deep-cone paste thickeners are commissioned in 2014. These trials studied the sedimentation and rheological characteristics of the existing tailings and performed deposition modelling to assist with developing short- and long-term designs for the tailings storage facility. To verify and optimise these models, Minera Esperanza considered a series of laboratory, pilot, and industrial-scale deposition trials. This paper provides a review of the trials conducted in the laboratory and at industrial-scale and considers the results and optimisations for the short- and long-term design of Minera Esperanza’s tailings storage facility."

Jan 1, 2014