Search Documents

By Cen Guoji

The foundation of bored pouring concrete pile have been adopted in the bridge engineering of China since early in the sixties. They demonstrated tremendous technical advantage and achieved notable economic benefit. With improvement of bridge technique including construction technique work equipment, design theory, examination in quality and applicable range etc, the pile diameter became bigger and the foundation changed from shallow to deep-water. This paper examples Jiujiang Bridge of Guangdong in China, which is single-tower cable-staged bridge, total length of 1675m, and expouds adopted successfully the foundation of variable section large bored pile (upper part d=3m, central part d=2. 4m and lower part d=2m) on the conditions of complicated technique that the load is tremendous (it require specially to resist 12000 kN ship impact) and the piles have free length 30m. The paper will be to describle design project and construction practice of pile foundation with variable section, and to compare schemes of equal section pile and pile in sinking-well.

Jan 1, 1991

Jan 1, 2003

By Gang Guo, Zhong Liu

"In response to an increasing demand of anchored structures for underground space and transportation infrastructure in China, an innovative underreamed ground anchorage system was created. The novel anchorage system has provided more efficient functions with higher capacity at lower cost, because of the enlarged cylindrical body (known as ECB) sealed in capsule at bottom of anchorage. This paper presents the detailed structure of innovative anchorage system and its special features. To investigate the bearing mechanism of new anchorage, we evaluate its performance and failure mode based on the experimental results, and also indicate its strain-hardening load-displacement relationship. Unlike the shaft anchorages, it is identified no overall failure to be found in soil surrounding the underreamed anchorage. More importantly, the anchorage capacity is governed by the base resistance, which takes more than 80% of total pullout capacity resulting from the contribution of ECB. Finally a case history of anti-floating project introduces the new combined construction approach and procedure, which has provided the contribution to the quality control and cost efficiency.INTRODUCTION AND BACKGROUNDThe construction boom over two decades in China has resulted in an increasing demand for underground space and slope stability. The infrastructures market requires the more efficient anchorage systems for retaining structures, resisting uplift forces and slope protection. The major concern focuses on gaining higher capacity and lower cost resulted from perfecting anchorage systems. There are three main anchorage systems designed to achieve the above objectives: ? single bore multiple anchorage system (Barley 1997), ? regroutable anchorage system (Smoltczyk 1991), ? underreamed anchorage systems (Xanthakos 1991). Generally, the concept ? comparing with the other two, can be more competitive due to its distinct advantages. To improve the performance and durability of ground anchorages under the complex geological conditions and diversified engineering requirements, a number of different underreamed anchorage technologies had been used, which included cone - shape anchorage described by Liao, Wu and Shu (1997) in Taiwan, Soilex anchorage developed in Sweden (Massarsch et al. 1997), Soletanche anchorage proposed in France, blasting anchorage used in Czechoslovakia (Hobst and Zajic 1986), jet-grouting anchorage innovated in Europe (Anon 1988), as well as deep mixing anchorage created in Japan (Cheng et al. 2000).The underreamed anchorage systems have the remarkable advantages compared to the shaft anchorage system. However, there are also some weaknesses inherent in the underreamed systems. For instance, the mechanical underreamed anchorage is unsuitable in sand or waterbearing ground, because the enlarged hole is easy to collapse, and it is hard to ensure the quality of anchorages. On the other hand, relying on the blasting in deep hole, the geometrical space and dimension of enlarged hole is uncontrollable, meanwhile, the continuous blasting operations may easily cause the serious ground deformation and the negative effects to the completed anchorages."

Jan 1, 1900

Jan 1, 2002

By Sam Warren, Antonio Marinucci, Genesis Z. Figueroa, Anne Lemnitzer

Drilled Displacement Piles (DDP) provide an ideal deep foundation solution that combines the benefits of ground improvement with traditional advantages of piling systems. This paper consolidates data from 20 construction projects in which more than 30 DDPs were installed and tested axially. High quality site exploration data (e.g., Cone Penetration Test and Standard Penetration Test) were evaluated to derive geotechnical analysis parameters. The test sites consisted of mostly mixed soil types with strongly stratified layers of sand, silt, and clay. Pile diameters ranged between 40 cm and 61 cm. Test results were compared with predictive methods developed specifically for DDPs as well as methods used in general geotechnical practice. The accuracy of the empirical methods is presented in terms of total pile capacity, pile length/diameter, and soil type. The large majority of all examined methods underpredict the in-situ pile capacities. It was also found that the difference between the tested and predicted capacity is strongly related to the level of improvement in the surrounding soil due to the piles’ installation. A general comparison between predictive axial accuracy and the observed level of ground improvement upon installation is also discussed.

May 1, 2022

By Dr Karsten Galipp, Kai-Julian I. Hendler, Prof. Manuel G. Pinheiro, Dr Peter J. Bourne-Webb

With a share of approximately 11% of global greenhouse gas emissions, the construction industry contributes significantly towards climate change. This is why construction projects should not only be assessed on costs and technical solutions, but also on their carbon emissions. Life Cycle Assessment (LCA) is a tool which can quantify the environmental impacts of a construction project over its entire lifetime. The objective of this study was to determine the carbon footprint of three types of quay wall structures, namely sheet pile combi-walls, open piled decks and caissons using an LCA approach. Each of these quay walls were studied under the same boundary conditions, such as design life, ground conditions, dimensions, location and so on. The analysis showed that the sheet pile wall has the lowest carbon footprint whereas the open piled structure has the highest. Furthermore, it could be shown that the largest share of greenhouse gases (approximately 80%) is emitted during the production of construction materials. The transportation of materials and construction activities each contributed under 12% to total emissions. The sensitivity analysis showed that with innovative approaches, such as adapting the concrete mix design, the carbon footprint could be reduced by 26% to 40%.

May 1, 2022

By Bengt H. Fellenius

The design of pile foundations is much more commonly verified by means of a full-scale test, than is the design of other foundation units. The reason is not that our knowledge of pile behavior is more uncertain than our knowledge of other foundation types making the verification necessary, but more that the loads in a structure are more concentrated to single foundations in a structure founded on piles as opposed to structures on footings or mats. Therefore, should a pile cap fail or move, the adverse consequence of this is often drastic, as the piled structure has little freedom to transfer its need for support to other foundation units. Consequently, it becomes important to assure the design of piled foundations. In many, maybe in most instances, the static pile loading test is routine and geared toward determining an at least capacity, only. However, in these times there is an ever increasing liability of the professional, demands for increased economy of the foundation, and frequent lack of the involvement in the test of the experienced old-timer exercising good judgment. Furthermore, modern pile design is leaving the single, simple concept of capacity and requires more information from the test to assist in determining aspects of long-term behavior and settlement. Therefore, even the straight forward, routine static loading test requires improved planning, execution, and analysis.

Jan 1, 1990

Jan 1, 1985

This specification, along with the drawings, encompasses all designs, materials, products, accessories, tools, equipment, services, transportation, labor and supervision, installation techniques, and testing procedures required for the installation of soil nail excavation support or earth retention systems. This is a Guide Specification designed to assist in the development of project specifications for soil nail excavation support and earth retention systems. This Model Specification is based on generally accepted industry standards but may require modification by the specification writer to accommodate unusual and/or unforeseen site and subsurface conditions and the particular circumstances of the project. Care must be taken to avoid internal inconsistencies. It contains language allowing for a Contractor-Designed Soil Nail Wall, which would be removed if the design is provided by the Owner (e.g. See Sections 1.2 and 4.1).

Jan 1, 2010

By Derrick Dasenbrock

Two DFI committees independently organized two complimentary panel sessions for the recent American Society of Civil Engineers' (ASCE) Geo- Risk 2023 "Advances in Theory and Innovation in Practice" Conference in Arlington, Virginia, July 23-26. The Geo- Institute (GI) specialty conference welcomed more than 200 professionals and students interested in risk from around the world to the Washington, D.C., area for three full days of plenary keynote lectures, papers and no-paper sessions. The GI Risk Assessment and Management Technical Committee organized the event, which is the third in a series planned on a 6-year cycle. The previous two events were in 2011 in Atlanta and 2017 in Denver.

Sep 1, 2023

By Paul A. O’Brien, Gary A. Chapman, Thomas G. Cuniowski

"The new Amcor B9 paper mill in Botany, NSW, Australia, involved the design and construction of a new paper mill founded within the Botany Basin Sediments. There were numerous design and construction challenges to address, including tight settlement tolerances for the paper machine footings (6 mm total and 1/2000 mm differential limits), high variable and cyclic loads, deep (>25 m) bedrock and uncontrolled fill material across the site. The mill structure design incorporated a deep driven precast and CFA piled foundation solution, with a comprehensive swathe of testing to validate pile capacity and expected settlements. The pile design for the mill structure included the installation of approximately 1000 piles, with pile testing comprising dynamic testing and a static load test on precast piles. With consideration of Sydney’s increasing demand for development space in relative close proximity to the city’s CBD, industrial areas in the Botany Bay area are likely to make way for heavy or complex commercial and residential structures. Therefore, a better understanding of the engineering behaviour of sediments underlying these areas would allow for efficient foundation solutions. This paper presents a discussion on effective foundation testing techniques and the effects that the behaviour and characteristics of the Botany Bay sediments impose on deep piled solutions.2 PROJECT DETAILS2.1 New paper millThe project involved the construction of the largest recycled paper machine in Australia. The paper machine is 330 m (1080 ft) long, 22 m (72 ft) high, and capable of producing 1.6 km (1 mile) of paper per minute. Construction commenced in early 2011 and new paper mill officially opened in early 2013. The early works contract was awarded to Baulderstone Construction Pty. Ltd. (Lend Lease Corp. Ltd.), with the D&C contract awarded to a consortium headed by Leighton Contractors Pty. Ltd. (CPB Contractors Pty. Ltd.), which included Golder Associates Pty. Ltd. as the geotechnical designer and reviewer.2.2 Site history and effect on local topographyThe site has been used as a paper mill since 1902, and as such, has layers of uncontrolled fill and buried objects within the upper fill materials associated with historical industrial use. The fill material generally comprised of loose and very loose sands, with isolated pockets of cohesive materials, peats, pulped paper and general construction waste. In addition, during construction, underground storage tanks were identified at depth, indicating the historical extent of filling across the site was extensive. The presence of this generally uncontrolled fill was a factor for determining that the most cost effective foundation solution for the paper mill was piled foundations, to bypass these materials."

Jan 1, 1900

By Aditya Ayithi, William G. Ryan, Dean Herbst

"For rock socketed drilled shafts, it is a common practice not to include the frictional resistance of overburden soils into the nominal capacity estimation. The primary reason often being cited is “overburden soils resistance is negligible compared to that of rock socket resistance.” However, in certain geological conditions, where the rock layer is located at greater depths, friction resistance from overburden layers can be significant. In addition, at such great depths, shaft drilling becomes very complicated and expensive. In these situations, considering the resistance of the overburden layers can be an economic alternative.This paper presents a case study of an Osterberg cell (O-cell) load test conducted on a 161.8 feet long and 78-inch diameter instrumented test shaft. Based on initial designs, a 72-inch diameter rock socket of lengths 23 and 26 feet was required to provide a LRFD factored friction resistance of 3,200 kips. The load test results revealed that the material in the 72-inch diameter socket does not represent a true rock. However, the test results also proved that the factored friction resistance of overburden layers is greater than the required design resistance. Based on the load test results, it was decided to allow the overburden soils frictional resistance to be considered in the shaft design, resulting in significant economic savings.INTRODUCTIONRock socketed drill shaft design guidelines of various State Department of Transportation (DOTs) agencies allow friction and/or end bearing resistance of only the rock socket portion into the design capacity estimation. It is typical to neglect the frictional resistance of overburden soils. However, in certain geological conditions where the rock layer is at greater depths, friction resistance of the overburden soils can be significant. In this case the friction resistance of overburden soils was verified via the specified instrumented O-cell test program and then used as part of the design capacity.PROJECT DESCRIPTIONAs part of I-29 improvement project, Iowa Department of Transportation (Iowa DOT) planned to replace the dual four lane bridges that cross the Floyd River in Sioux City, Iowa with dual six lane bridges (Fig. 1). Expected benefits from this improvement include improved safety, traffic operations and roadway infrastructure conditions.BRIDGE SUBSTRUCTUREThe project consists of two individual bridges; a new south bound bridge and a new north bound bridge. The south bound bridge is 646-ft long and the north bound bridge is 644-ft long. Both are six-span, pretensioned and pre-stressed concrete beam bridges of varying width. Bridge foundations were designed such that the abutments of both bridges will be supported on driven steel piles and the bridge piers will be on drilled shaft foundations."

Jan 1, 2016

By Mary Ellen Large

This publication of Deep Foundations Institute (DFI) is intended to provide project owners, design engineers and construction professionals with guidelines for selecting cutoff wall and barrier systems and a general introduction to their methods of construction. Three categories of cutoff wall and barrier construction technology (excavated cutoff systems, in situ techniques, and driven cutoff systems) are presented and parameters for evaluating their design and construction are discussed. The information presented was compiled from the opinions of practicing engineers and construction specialists from the DFI Slurry Wall Committee.

Jan 1, 2021

By Martin Walker, Joseph Ang, Jongwon Lee, Alvin Bayudanto, Lilian Lorincz, Morteza Khorshidi, Wenyong Rong

This paper presents a case history of liquefaction susceptibility evaluation study for a major infrastructure project in the San José area. The subsurface material of the study area consists of Holocene alluvial deposits composed of interbedded and crosscut clays and silts, sands and gravels. The simplified approach for liquefaction triggering evaluation was carried out using both CPT data and SPT data representing site’s seismic capacity and the peak ground acceleration associated with a return period of 975 years at ground surface representing seismic demands. Site-specific cyclic stress ratio (CSR) profiles as seismic demand are also estimated from one-dimensional site response analysis. The simplified approach uses empirical depth stress reduction factors (rd) based on generic shear wave velocity profiles to account for the non-rigid response of the soil profile in estimating CSR. The CSR profiles of the simplified procedure were examined by completing site response analyses using site-specific soil profiles to represent site-specific seismic demands in the liquefaction triggering evaluation. The paper concludes with a comparison and discussion of the liquefaction evaluation examining results from CPT versus SPT data, and the comparison of CSR profiles from the simplified procedure versus site-specific response analysis.

Sep 8, 2021

By Pathik Deb Mallik, Shyamal K. Mitra, Rajiv Kishore, Shuvranshu Rout, Manos De

"This paper presents a case study on the design and construction of a deep underground pit structure constructed inside almost a century old existing plant building. The complexity and challenge for the design and construction lay in executing the work in a difficult subsoil condition especially the presence of deep mica schist. The limited space availability in the existing plant for construction work without hampering regular production in other adjoining areas of the plant made the execution more challenging. Experience with difficult subsoil and proximity to old foundations entailed a non-conventional engineering approach while ensuring complete safety in spite of maintaining the normal operation.INTRODUCTIONTata Steel Processing and Distribution Limited (TSPDL) is a subsidiary unit of Tata Steel Limited (TSL) having a CR processing facility inside the premises of Tata Steel Limited. TSPDL intended to install equipment for a new slitting line inside the existing shed including construction of very deep structure called “loop pit” where the strips from cut CR sheets collect in the form of loops and are recovered as scrap. The entire plant is located within the shed of existing plant. The construction of all foundations including the loop pit is to be executed in the limited area without disturbance to normal production work in balance areas of the plant and also maintain safety and integrity of existing structures.The existing shed is an old structure constructed approximately 80 years ago. The building column foundations are gravity type design of brick masonry supporting only the vertical load from the columns. This type of foundation designed with no eccentricity of loading provides no allowance for implementing any foundation stabilizing design. The present project required civil construction for the new equipment foundations safely within this area."

Jan 1, 2015

By Ambarish Ghosh, Rituparna Dey, Indrajit Chowdhury

"In port and harbor facilities, jetties and cargo berth terminals are usually installed on piles that remain partially embedded in soil, while a part of it behaves as columns supporting top deck. Technology in vogue adapts a pseudo static analysis in computer where the top deck including piles are analyzed as an integrated system based on finite element method when the piles are modeled as beam elements, while the soil in which it is embedded is modeled as linear or nonlinear springs. Typical berthing force of the ship is considered as a pseudo static force where the dynamic characteristics of the force is taken into consideration by an equivalent impact factor and little study exists on the actual behavior of these type of piles under the transient shock due to berthing impact. Present paper proposes an analytical solution based on which one can compute the dynamic response of such jetty piles considering shear modulus of soil constant with depth. Considering the solution is analytical in nature no special software is needed and can well be adapted fordesign office practice using generic utility software like MATHCAD, MATLAB etc. that makes theproposed model computationally very efficient.INTRODUCTIONResponse of piles under dynamic load has been an important study in the realms of civil engineering, where significant research has been carried out on its dynamic behavior under harmonic loads like one experienced in a machine foundation or under seismic force.A number of researchers have given solution to this problem like Parmelee et al (1964), Tajimi (1966), Penzien (1970), Novak et al (1974, 1983), Banerjee and Sen (1987), Dobry and Gazetas (1988),Chowdhury and Dasgupta (2008).However, most of these theories are based on piles loaded under harmonic load and valid for long piles where structural failure precedes the soil failure considering the piles are long and flexible."

Jan 1, 2015

By Phil Wilkinson, Sam Whitaker

"The installation of large (XL) diameter monopiles offshore typically requires expensive and specialist plant, equipment and vessels. Due to the increasing size (weight, diameter and length) of the foundations, in order to mitigate installation risk, the use of large diameter drills is becoming an increasing requirement.Project developers often try to avoid drilling operations due to the time associated with the drilling process. This restricts projects in terms of location and it also overlooks the additional engineering benefits drilling can bring to monopile foundation design e.g. reduced foundation material and better fatigue design life.By comparing the lessons learned of three milestone overwater drilling projects; methods of maximising drill speed and decreasing drilling process time is established. Particular emphasis is put on pile internal relief drilling in a process known as Drive-Drill-Drive (DDD).The milestone overwater drilling projects are North Hoyle Offshore Wind Farm (OWF) (2003); Flamanville EPR cooling water outlet shaft (2008); and Gwynt-y-Mor OWF (2014).By evaluating the effect of foundation pile diameter on drilling process times, example foundation installation costs are derived and used to show that incorporating drilling as part of a process may not be cost prohibitive to projectsContinued advances in drill technology, and drilling rates of penetration, combined with an integrated approach to foundation design, challenge whether hammering only is always the optimal solution for XL monopile installation."

Jan 1, 2017

By Richard D. Luark, Fernanda S. Madrona

Designing temporary retaining systems that allow for deeper excavation amid the existing urban infrastructure has become a challenge. A 60-foot-deep excavation in downtown Seattle was required to construct five levels of below grade parking for a 35-story high-rise building, Tower 12, next to an existing 20-story tower with three levels of below grade parking, separated from the project by an 18-foot wide alley. The solution was to combine two temporary excavation support systems, soil nailing and anchored soldier piles, to work within the site constraints. Densely-arranged, short-length soil nails were used to support the upper 30 feet of the excavation, while the lower 30 feet of the excavation was supported with soldier piles combined with steeply-inclined, high-capacity ground anchors, which extended below the adjacent building foundations. The combined temporary support system eliminated the need for internal bracing, reducing construction cost and schedule. The performance of the combined soil nail and soldier pile system was monitored with an inclinometer and optical survey monitoring, which demonstrated the performance of the combined temporary support system. This paper provides a discussion of the advantages of combining different excavation systems and an analysis of movement monitoring data collected. SITE CONDITIONS AND PROJECT INFORMATION Tower 12 consists of a 0.45-acre development with 36-stories of mixed, residential and commercial use with four levels of below grade parking. The project site is bounded by the Cristalla Condominium to the north, Virginia street to the south, 2nd Avenue to the East, and an 18-foot wide private alley to the west. The One Pacific Tower Condominium, which has three levels of below grade parking, was located to the west across the alley. A site layout plan is presented as Figure 1. As shown in Figure 1, the construction of the west wall required a maximum 51-foot-deep excavation, from elevation (EL) 162 feet to EL 111 feet. Adjacent to the west wall, the existing alley grade varies from elevation 154 to 161 feet, leaving a narrow block of soil 18 feet wide and up to 42 feet high to be shored along the alley in order to reach the One Pacific Tower bottom of mat foundation at EL of about 120 feet. In addition to the existing One Pacific Tower Basement wall, site constraints included existing utilities along the alley such as an existing 4.5-feet wide by 7-feet high vault, with bottom at approximate EL 146 located 10 feet from the back face of the proposed Tower 12 basement wall.

Jan 1, 2019

By Takefumi Takuma, Tsunenobu Nozaki, Masashi Nagano

Using sheet piles and pipe piles for permanent earth retaining is one of the most economical methods for constructing basement walls since they can also work as temporary shoring during construction. A major mixed-use redevelopment project in the UK, encompassing two to three large city blocks, utilized both sheet and pipe pile walls for a two-level subterranean parking structure. The 290m (950ft) x 100m (330ft) basement’s steel walls were designed to temporarily support excavation during construction and eventually to become a load carrying permanent structure in order to expedite the construction process and to achieve cost reduction. Two types of press-in piling machines, one for sheet piles and the other for pipe piles, were used for the job because of their abilities to press in sheet and pipe piles within tight tolerances for finished walls, for difficult installation conditions with very hard soil, and for its very low noise and practically zero-vibration operation; an essential factor for the job in close proximity to other businesses and residents. BACKGROUND Steel sheet pile and pipe piles have been used for many purposes including earth retaining. They are produced at steel mills and spirally welded at a fabrication yard to their corresponding specifications under strict quality control measures. Therefore, they can form highly reliable walls to its design capacity with proper installations. Their advantages as underground walls are:  They can form a high level of water cut-off function with their interlocks sealed by welding or with hydrophilic materials. See Figure 1 for a few examples for a sheet pile application.  They can carry vertical loading in addition to horizontal load and bending moment.  They can be a self-standing and temporary/permanent wall with flexible design and construction processes; bottom-up, top-down or hybrid sequences can be chosen per the project’s needs.  They can form a thinner wall than other wall types, creating larger inner space. See Figure 2.

Jan 1, 2019

By Sumit Kumar Biswas, Moyukh De, Sibapriya Mukherjee

"The piles often are also subjected to lateral (horizontal) forces and moments. In fact, there are some structures where the primary function of piles is to transfer lateral loads to the ground. Proper analysis of laterally loaded piles is very important to the geotechnical and civil engineering profession.In the present investigation an experimental study has been carried out with free head short model cast iron hollow piles of outer diameter of 24 mm and L/d ratios of 8, 10, and 15. The experimental results have been supplemented by numerical techniques using PLAXIS-3D Foundation version 2.1 software. The results have been found to agree reasonably well with the experimental results. Further finite difference approach has been adoptedto reduce the computational time and to calculate the coefficient of modulus of subgrade reaction (?h) from the load- deflection data obtained from PLAXIS output at different pile depths. The parametric study has been extended for the non-dimensional form defined as flexibility ratio (F.R.),where ?h, L, Ep and Ip are the coefficient of modulus of sub-grade reaction, the embeddedlength of model pile, elastic modulus of pile material and the moment of inertia of model pile about the central axis respectively).The variation of coefficient of horizontal modulus of sub-grade reaction (?h) has been studied with respect to the following parameters for homogeneous soil system: relative density andL/d ratio. It has been found that the logarithm of flexibility ratio increases with increase inrelative density and increase inL/d Ratio. The values of ?h obtained by the proposed method have been, found to be close to the numerical results.As output of this research, graphs have been generated in respect of different parametric variations to gain an insight into behavior of piles under lateral load for short piles."

Jan 1, 2015