Search Documents

By Shahid Islam, Lucian Bogdan

Deep and large diameter drilled shafts use mostly bundles of Grade 60 (415 MPa) reinforcing bars as longitudinal reinforcement with rebar splices to make it longer. Lower Grade steel requires large number of bars which result in rebar congestion and difficulty in placing concrete. This leads to increased labor cost for fabrication and installation. By utilizing larger size and higher strength threadbar, the congestion of rebar can be reduced significantly and bundling of bars can be avoided. The lap splices are replaced with simple threaded couplers and end hooks are replaced with end terminators. Threadbar conforms to ASTM A615-15 and can be epoxy coated if required for corrosion protection. This paper describes an attractive value engineering of replacing Grade 60 (415 MPa) bundle of rebars with larger diameter Grade 75 (515 MPa), Grade 80 (550 MPa) and Grade 100 (690 MPa) threaded bars and threaded couplers in some specific drilled shaft projects in the USA. INTRODUCTION A drilled shaft which may also be referred to as drilled piers, caissons, cast-in-drilled-hole piles and bored piles is the key element to the foundation of massive structure. They are used for tall buildings, bridges and foundations for other applications such as retaining walls, sound walls, signs, or high mast lighting. Drilled shaft foundations are typically 3 to 12 feet (0.9m to 3.7m) in diameter cast-in-place deep foundation elements constructed in a drilled hole that is stabilized to allow controlled placement of reinforcing steel and concrete. Drilled shafts for transportation structures are commonly used to depths of up to 200 ft (61m) in the USA. Drilled shafts can be installed in a variety of soil and rock profiles, and are most efficiently utilized where a strong bearing layer is present. The reinforcing cage is typically lowered into position within the hole and then concrete placed through the center of the shaft, flowing from bottom to top through the reinforcement to fill the hole.

Jan 1, 2018

By Gray Mullins

This paper presents results from model and full-scale tests to assess the interface bond between a cast-in-place concrete seal slab and steel H-piles in cofferdams. Three different seal slab placement conditions - fresh water, salt water and bentonite slurry - were evaluated and the results compared against controls where no fluid was displaced by the concrete. Normal pile surfaces were investigated. Additionally, the situation of ?soil caked? piles was also tested. In the model tests, eight 15 cm deep, W6 x 15 sections were used for two different embedment depths of 1.5d and 2d, d being the depth of the section. In the full-scale tests, 16 specimens 35 cm deep (W14 x 90 sections) were tested with the embedment varied between 0.5d-2d. The results show that significant bond stresses developed even in the worst placement condition. Recommendations made for revising current values in specifications have already been implemented by the Florida Department of Transportation.

Jan 1, 2013

By M. T. Davisson

Pile compression load capacity prediction methods are divided into four categories for purposes of discussing their reliability compared to static load test results. The categories considered are: 1) static analysis, 2) driving formulas, 3) wave equation analysis, and 4) dynamic measurement and analysis. It is concluded that any method of static analysis that works for the geological deposit in question may be satisfactory. However, any given method can be quite wrong when applied to other deposits of soil that are different in terms of their engineering and geological characteristics. Dynamic formulas are found to be theoretically unjustifiable. The ready availability of the wave equation analysis for microcomputers eliminates the need to utilize dynamic formulas. The wave equation analysis is found to be the best analytical method for making predictions both for design and for construction control. Dynamic methods of measurement and analysis are found useful, but have limitations that have caused troubles on many projects. Two case histories are presented that show the limitations of dynamic measurement and analysis, and of the wave equation analysis. Soil deposits exist that defeat both the wave equation and dynamic measurement techniques; static load tests are currently the only method of proving the load capacity of piles in such soils.

Jan 1, 1991

By John P. Turner

The behavior of tieback retaining walls depends on many factors, including soil properties, groundwater conditions, construction sequence, spacing and stiffness of tiebacks and soldier piles, tieback loads, and others. The primary design considerations for tieback walls are 1) adequate stability and 2) limiting wall movements. Traditional design methods rely on apparent earth pressure diagrams and experience to predict the forces which must be supported by the tiebacks to provide adequate stability. The required soil properties depend upon whether the soil is sand, soft clay, or stiff clay. Design to limit wall movements is more difficult and the usual approach is to design the wall with an adequate factor of safety for stability and then evaluate wall movements during construction through the use of load tests on individual tiebacks and monitoring of wall movements by optical surveying, slope indicators, and extensometers. If excessive movements are likely to occur, it is often not known until construction is well underway. This approach is reflected in the fact that few tieback walls fail due to a lack of adequate stability, while most litigation involving tieback wall performance is related to excessive movements. Much progress has been made in recent years in methods for predicting the movement of all types of insitu retaining walls (Clough et al. 1989, Clough and O'Rourke 1990). These methods are based upon both experience and analytical methods. This paper reviews the methods currently available for evaluating both the stability and movements of tieback retaining walls. Case histories involving excavations constructed in the downtown Seattle area are used to evaluate the applicability of the available methods to Seattle conditions and to illustrate the importance of soil behavior in tieback wall performance.

Jan 1, 1990

By Dean E. Matthews

The concept of a pile for construction is credited to a Neolithic tribe called the "Swiss Lake Dwellers" who lived in what is now Switzerland about 6,000 years ago. They used piling, not for supporting heavy loads as we do today, but for elevation to protect themselves from wildlife. The Romans often used piles, and built many structures, including buildings, homes, bridges, roads and viaducts on piling. The Romans built the first bridge across the Tiber River in Rome on timber piles in B.C. 1620. Homes in the cities of Venice and Ravenna were built on piles from B.C. 100 to A.D. 400. The Romans also built the first bridge across the Thames River in London in A.D. 60 on timber piling.

Jan 1, 2003

By Dan Brown

Two drilled shaft foundations were subjected to axial load tests in order to measure the influence of drilling fluid on performance. Other than the differing drilling fluids, the shafts were constructed with great care to ensure identical conditions. The results indicate superior performance in both side shear and base resistance of the shaft constructed using a polymer over that of the shaft constructed using bentonite drilling slurry.

Jan 1, 2002

By Kul Bhushan

This paper presents the results of lateral load tests on 0.61-m to 1.27-m (24 to 50-inch) diameter drilled and cast-in-place piers in San Diego area residual/formational soils. The test piers were installed and tested in the following soils: Decomposed Granitic Rock (Ktd), Stadium Conglomerate (Tst), and Friars Formation (Tf). Lateral loads of up to 845 KN (190 kip) were applied to the piers in residual granitic soils, and loads up to 1780 KN (400 kip) were applied to the piers in Stadium Conglomerate and Friars Formation. The tests were conducted by jacking against adjacent piers and monitoring the lateral load and lateral deflection at the ground line. Test results indicate that ultimate lateral pile capacities of up to 1800 KN (400 kip) can be obtained for 0.61 m (24-inch) drilled piers with penetration of 3 to 6 m (10 to 20 ft) in the residual/formational soils tested. Lateral load analyses using p-y curves for very dense sand significantly overestimate the observed lateral deflections. For lateral load analyses using dense sand p-y curves, p-multipliers that increase the lateral soil stiffness (p-y curves) by 2 to 8 times are required to match the load-deflection behavior measured in the test piles. When applied to the dense sand p-y curves, the p-multipliers provide a more accurate prediction of load-deflection behavior in the residual/formational soils, and can result in shorter required pier penetration and significant savings in foundation cost.

Jan 1, 2002

By D. A. Bruce

Small diameter cast-in-place bored piles (pinpiles) have been installed throughout the world since 1952, but only more recently in the United States. The special features of their construction and performance makes them ideally suited for structural underpinning applications in difficult ambient and geological conditions. This paper describes the underpinning of part of a major industrial facility near Mobile, Alabama. In addition to being a most interesting and successful case history, per se, the paper also describes in detail a fundamental test pile program which has afforded a unique insight into the basics of load transfer mechanisms.

Jan 1, 1992

By S. X. Liang

In China, the bearing capacity predictions of the pile with Stress-Wave Theory have been developed rapidly in recent years. This paper recommended a DZH-3 Pile Driving Analyzer and its relevant computer programs. Taking Qinghai Hotel Project for example, it gave their applications in the dynamic tests of large diameter cast-in-place piles.

Jan 1, 2010

By Mark M. Petersen

As part of the addition of eight new combined cycle generating units at the Florida Power & Light Sanford Plant, 2,129 piles were to be installed. The existing plant elements were supported on driven piles, and the variation in pile lengths during previous work, as well as available subsurface information, indicated a complex stratigraphy. At the request of the owner, the designer/construction manager developed a program to evaluate the use of pressure-grouted displacement piles. A pre-design load test program in areas that represented the apparent extremes in subsurface conditions indicated that the system was feasible; however, the presence of existing features that were to be demolished later precluded the clear delineation of subsurface conditions in advance of construction. A contract was negotiated with the pile installer based on the best estimate of potential pile lengths, with modifications to pile lengths to be set based on additional exploration. A total of 52 cone penetration soundings and five load tests were performed immediately prior to and during pile installation to establish correlations between the CPT data and pile performance. Pile depths were set based on these correlations. Pile installation was completed 6 weeks ahead of schedule and 15 percent under the original budget estimate. This paper documents the evaluation of pressure-grouted displacement piles as an emerging technology, and illustrates the benefits of a close working relationship between the owner, designer, and pile contractor at a site with variable subsurface conditions.

Jan 1, 2002

By Zhang Baoshan

In this paper, the forced features and dynamic behaviors of stone-column composite foundation are concisely related. The characteristics of Rayleigh wave method is summarised. This method is proposed in which, the stress ratio of the stone-column to the surrounding soil and the bear­ing capacity of the composite foundation are determined. Through the engineering cases, it is shown that, checking and evaluating the composite foundation in this method, is feasible, with high speed and low cost.

Jan 1, 1991

By Hal W. Hunt

Steel and concrete piles and power-actuated hammers have developed almost entirely within the past 100 years. Prior to that time, piles were mostly timber, driven with a drop hammer or a maul. The Engineering News Formula ? for timber piles driven with a drop hammer at a factor of safety of six ? was promulgated by Wellington in 1888. Steel com­panies supplied fabricated and rolled shapes for piles in the early 1900's. The thin shell and then uncased concrete piles originated about that time. Now leads have become sophisticated to accurately spot a pile at any required batter. Hammers have grown to phenomenal size and vibratories are being accepted at full value.

Jan 1, 1984

By Jørn H. Thomsen

This paper presents the experience gained and the lessons learned over the last decade within the numerous offshore foundation projects undertaken in the offshore waters of Denmark and Belgium by COWI A/S of Denmark. This experience derives from the close collaboration with, and interaction between the owners, contractors, and engineers in the various stages of project development. In turn, the experience draws on COWI's experience within foundation of large bridges world wide over half a century. Focus is on two pioneering gravity base foundation projects: ? Nysted in Denmark, currently the largest offshore windfarm worldwide with 72 Nos Bonus 2.3 MW turbines in water depths up to 10 m in the relatively benign inner Danish waters ? Thornton Bank in Belgium, where the first phase - comprising 6 Nos REpower 5MW-turbines of a total of 60 - are planned to be built in the rough North Sea in water depths exceeding 25 m.

Jan 1, 2013

By James W. Weaver

The 2,120-foot long cable stayed Penobscot Narrows Bridge that carries US Route 1 over the Penobscot River between Verona Island and Prospect, Maine is supported on four foundation units, one below each pylon and one at each abutment. Due to varying subsurface conditions along the bridge alignment, the structure was designed to be supported on foundations consisting of high-capacity steel H-section piles (Verona Pylon), a mat bearing on a prepared bedrock surface (Prospect Pylon) and spread footings bearing on compacted rockfill (abutments). The 70-foot by 80-foot (plan area) Verona Pylon foundation was designed to be supported by 288, 430-kip design capacity steel H-section piles (HP14x117, 50 ksi steel) driven through up to 100 feet of dense glacial till deposits containing cobbles and boulders up to 3 feet in diameter. The piles were installed using a single-acting diesel hammer (Delmag D62-22) with a maximum rated energy of 165 kip-ft. Thirteen representative piles were selected for dynamic testing (ASTM D-4945) to verify pile capacity, hammer efficiency and pile stresses. Dynamic testing determined that four different pile driving criteria were needed across the site due to variation in the bedrock and soil resistance below the footing plan area. Approximately 4 percent of the production piles were damaged/rejected due to misalignment and/or damage as a result of encountering the cobbles and boulders embedded in the glacial till. The rejected piles were located randomly throughout the plan limits of the foundation mat. Subsequent structural analyses indicated that the foundation was capable of safely supporting the design loads without the need for installing replacement piles. Evaluation of dynamic testing results with signal matching and pile driving records provided valuable information on pile side and tip resistance. Evaluations were made regarding predicted versus actual pile lengths, pile bearing material, distribution of skin friction and end bearing capacities.

Jan 1, 2011

By Anil Bhandari

Using subsurface data collected at each drilled shaft location is an ideal approach for conducting drilled shaft design. However, conducting subsurface tests at each drilled shaft location and subsequently performing the drilled shaft design can be a daunting task for a noise barrier wall that is divided into six (6) sections and stretches for approximately four (4) miles. In addition, having individual drilled shaft designs complicates the construction process. Grouping the subsurface conditions into broad categories and performing the design for each of those categories is an attractive alternative to the design per boring approach. Currently there are no existing guidelines to aid a designer on grouping the subsurface conditions for the drilled shaft design for the noise barrier walls. Therefore, a method was developed based on the Standard Penetration Test (SPT) N values of the near surface soils to categorize the soil profiles into distinct categories. Since the soil engineering properties of the near surface soils are known to be critical for drilled shaft lateral capacity, these soils were emphasized in the methodology. This method was successfully implemented for the design of drilled shafts supporting the noise barrier walls along the I-20 in Columbia, SC. For this project, two distinct soil profiles, labeled as ?strong? and ?weak?, were used. An overview of the soil profile grouping methodology is presented as well as the vertical and lateral drilled shaft capacity analyses for this project for the two general soil profiles. The analyses indicated that the axial capacity governed the design in the ?weak? soil profile and the lateral capacity controlled the design in the ?strong? soil profile. However, this is not a generalization and whether the axial or the lateral capacity governs the design of drilled shaft depends on the soil profile and design loads. Nonetheless, our findings emphasize that both lateral and axial capacity should be checked for drilled shaft design even when the vertical load are minor.

Jan 1, 2011

By Charles L. Guild

I will add a few facts about the use and development of the Osterberg Test Load Cell and my association with Jorj. I first met Jorj in 1965 when the Guild Construction Co. drove 12" diameter cast-in-place shell piles for him at the Marquette Cement Co. in Nashville, Tennessee. When I met Jorj at the DFI Trustee's meeting in 1985 at Longboat Key, Florida, he showed me a sketch of his idea about using a test cell at the bottom of a caisson to test the end bearing and side friction on a caisson. He had made a successful trial test in Case International's equipment yard and wondered whether a similar device could be made for a driven pile. At first I was skeptical that it could be done but after thinking about it overnight I told him I felt it was feasible and we would do some work on it. At that time, there was a large bridge job going out for bid in Rhode Island using 14" square prestressed concrete piles'. Based on a record of the Guild Construction Co. Inc. driving over 3,000,000 feet of piling on work for the State of R.I., we felt we would have an excellent chance to be allowed to use them so we designed, detailed and fabricated three for 14" square prestressed concrete piles. As things worked out, we did not test them on this job and have not to date.

Jan 1, 1989

By Guo H. Lei

Over the last four decades, barrettes have been ever-increasingly adopted as the foundations for tall buildings and heavy infrastructure projects all over the world. Many findings have been gained from practical applications and theoretical researches. In this article, a collection of literature is reviewed on the installation effects and load-carrying behaviour of barrettes derived from field and laboratory tests and theoretical studies. It covers many aspects, such as the ground deformations and stress changes caused by the installation of barrettes, the shaft resistance mobilisation behaviour, the construction effects on the shaft resistance, and the effects of pile spacing, pile shape and pile group layout on the load-carrying behaviour of barrettes.

Jan 1, 2006

By K. Englehardt

J BERESFORD introduced the subject of the paper which is the use of polymeric slurries to support the sides of diaphragm wall and bored pile excavations during construction. In the opinion of the authors the use of a suitable polymeric fluid offers financial and technical advantages compared with traditional bentonite based slurries. Under quiescent conditions a support slurry must have the following properties. - sufficient viscosity to support the sides of the excavation, to prevent infiltration into soils and to hold loose soil particles in suspension. - when agitated it should thin quickly to assist pumping transfer and cleaning and allow free passage of the grab or drill. - viscosity should be low enough during concreting to facilitate placement but high enough to prevent contamination of the concrete.

Jan 1, 1991

By Lucien Weber

In the Shanghai area, the soil conditions are such that bearing piles have become an essential foundation part of the new highrise buildings. In order to reduce the settlements under the high working loads of about 2300 kN/pile, the Chinese building authorities require the pile tip to penetrate into the compact sand layer, situated at approx. 60-70 m depth. No H-piles have yet been tested under these conditions in Shanghai. This paper describes the driving of 8 H-bearing piles with 4 different shapes and with lengths varying from 45 to 75 m. Dynamic measurements are performed during driving and after a wait time of approx. 40 hours in order to assess the change in bearing capacity in function of time and in order to get an idea about the resistance distribution along the piles by using a stress wave analysis program (CAPWAP). One pile is equipped with channels between the flanges for executing verticality measurements with an inclinometer. However, this test has not yet been performed. One month after driving, two piles of 75 m length are statically loaded both in vertical and in horizontal directions.

Jan 1, 1987

By Khamis Y. Haramy

Quality assurance and quality control of drilled shafts has become a concern due to difficulties in accurately locating construction anomalies and determining load bearing capacity of defected drilled shafts. Various non-destructive evaluation techniques have been developed to estimate the integrity of the concrete in drilled shafts. While these techniques have been widely accepted, variables and unknowns can affect the measurement results. Results are typically difficult to interpret, leading to unnecessary construction delays and possible litigation over shaft integrity. In addition, influences of surrounding ground materials, stress states under different load conditions, and crack and residual stress development during concrete curing further complicate determination of shaft performance. This paper focuses on the evaluation of load bearing capacity of defected drilled shafts under various conditions by numerical analysis and modeling.

Jan 1, 2007