Search Documents

By A. Le Kouby

We present in this paper the results of a parametric study carried out in a calibration chamber on instrumented model piles. The aim is to point out group effect on piles within a group through their resulting shaft friction and tip resistance. The methodology relies on the study of the influence of adjacent piles on a "reference" pile. The soil used is a silica sand (Fontainebleau sand). The influence of parameters like pile spacing, number of piles and installation order are evaluated. The results show a positive effect on shaft friction of the group effect and a negative effect on tip resistance. Efficiency factors are defined in order to have a better view on the parameters influencing the response of the pile within a group.

Jan 1, 2006

By J. L. Liu

Long-term maintained load test on the bored pile group in unsaturated silty soil has been carried out. And the research on the time effects of bearing behavior of pile group has been done by the method of installing pressure cells and reinforcement stress gauges for measuring the soil reaction beneath the cap and the pile bottom as well as the shaft resistance. The test shows that, within a certain duration after loading, the soil reaction beneath the cap and the pile point resistance increase with time; but the shaft resistance decreases. The load distribution among the pile tops in the group tends to be even with time. The shaft resistance redistributes along the pile shaft with time, that is, getting less in the upper part, getting larger in the middle. The redistribution does not tend to stop till the distribution in both upper and middle part becomes to be uniform. The load-bearing conditions of soil beneath the cap of pile group and the variation in time effects with related factors also have been discussed.

Jan 1, 2010

By Rajesh A. Vaidya

A large scale piling work is undertaken in India for an important fast track industrial project. Thousands of solid square precast concrete piles are driven to depths of around 50m. Soils encountered are of alluvial origin with very soft clays varying in thickness from 10 to 18m at the top followed by medium dense to dense and occasionally very dense sand, stiff clay and finally dense to very dense sand layer as the founding layer. Recent site grading with around 4 metres thick hydraulically filled river sand necessitated driving the piles to the bottom sand layer to avoid problems on account of negative skin friction and to achieve optimum pile capacity. A process approach suggested by Bell et al (2002) to promote better understanding of the pile behaviour, pile capacity, and parameters assumed at design stage for static capacity and for wave equation analysis is followed with an aim to bring in effective economy in terms of pile length and pile installation speed. Soil investigation work is also undertaken in stages to cut down pile wastage. A judicious combination of PDA and static pile load tests is followed. Pile Driving Analyser (PDA) tests at end of driving and also at various stages of recovery of pile capacity are carried out to understand the pore pressure dissipation phenomenon. The paper attempts to present some of the valuable experiences that would go to establish precast pile as a very effective alternative to driven cast-in-situ piles and bored piles which are very common in this part of the world despite their limitations in terms of economy, speed and certain geotechnical aspects.

Jan 1, 2007

By Tony Suckling

"As we head toward the United Nations Climate Change Conference in Copenhagen in December, the environment and sustainability will become headline news for a while. Governments are expected to agree to a set of binding targets to reduce carbon emissions probably before 2020, and certainly before 2050. This will, in effect, initiate a low carbon economy in many parts of the world. Sustainability has mainly been rhetoric so far, the exceptions being projects for those looking to the long-term future and not for short-term financial gains.The probabilities and consequences of negative impacts on the environment and on society over the short term and in the long term can be assessed and mitigated, but mitigation often adds cost. Also, we cannot know what technologies will be available, say 1,000 years into the future, which is about 40 generations of our society. It is easier to have a connection with 100 years into the future, which is only about 4 generations. Individuals may have a different sense of sustainability, and place a different value on mitigation, its cost, its importance and its potential impacts.Sustainability means different things to different parties on a construction project. For example, a land developer is likely to have a different view on the design in terms of sustainability than that of the designer. The developer may also likely to be more interested in sustainabiliy if there are tangible economic benefits that might accrue. Achieving sustainability on any project, leads to conflict between competing interests or demands cooperation between the economic and technical sectors involved. The foundations for a building or bridge, by definition, need to interact with the ground whose behaviour cannot be dictated by man. The aims of sustainability are the same as for the building or bridge, both of which are constructed of manmade materials, but it is less clear how they should be achieved. An example is the driven pile that does not produce spoil waste, but is likely to be too noisy to be acceptable in an urban environment. This then begs the question, should the public accept the nuisance of short-term pile driving to achieve a more sustainable foundation? Additionally, the question has to be asked, can the deep foundations industry develop its techniques and products to help make them more acceptable and appropriate more often than is possible now?"

Jan 1, 2009

By Emad Farouz

This paper compares the predicted axial capacity of driven Pre-cast Pre-stressed Concrete (PPC) piles for the Lake Gaston Water Treatment Plant (LGWTP) using several design methodologies versus the axial capacity measured from dynamic and static load testing. The LGWTP site is located in Chesapeake, Virginia and is part of the Great Dismal Swamp. The subsurface investigation included soil borings, in-situ dilatometer (DMT) tests, and in-situ piezocone (CPTu) tests. The axial capacity predictions of the PPC piles were performed using the computer programs DRIVEN and FB-DEEP which are based on SPT N-values. Additionally, an empirical method proposed by Martin, et al. (1987) based on local experience with PPC pile design in the Yorktown formation in the Tidewater area of Virginia was also evaluated. Finally, the ?Laboratoire Central des Ponts et Chausées (LCPC)? method developed by Bustamante and Gianeselli (1982) based on CPT measurements was also used to develop the axial pile capacity of the piles. This paper shows that the FB-DEEP computer program and the LCPC method provided a reasonably good prediction of the pile axial capacity measured from PDA, CAPWAP, and Static Load Tests in comparison with the other design methods used. The soils in this area develop significant setup over time and it was found that FB-DEEP and the LCPC method are capable of incorporating this setup in the prediction of the long-term axial capacity of driven piles in this area.

Jan 1, 2007

By John E. Lens

Driving bridge foundation piles into glacio-fluvial sands and gravels and glacial tills brought surprisingly longer than predicted driving lengths on several recent projects in Vermont. In some instances, piles drove more than 40 feet past refusal depths predicted from Standard Penetration Resistances from borings terminating in glacial till. Overall, piles developed substantially less skin friction than predicted using common capacity formulas and drove as much as 80 feet longer than predicted in the moderate to dense gravelly and cobbly soils. These piles were driven for one to five span highway bridges within narrow valleys with bedrock ranging from 80 to over 200 feet deep. Piles were for both conventional and integral abutment bridges. H-piles were used for a variety of reasons including lower unit cost, better availability, and better ability to drive through cobbly soils in upper strata. Dynamic testing was used to evaluate capacity, including skin friction and end bearing capacity. In order to develop better pile length and capacity predictions for future projects, VTrans and one of their geotechnical consultants are collaborating to develop criteria for improved pile capacity predictions in these river valleys. We are doing this by evaluating driving and dynamic testing data from four projects in comparison with the Federal Highway Administration (FHWA) DRIVEN pile design software, and methods from Myerhof (1976) and Tomlinson (1981). Our overall objective is to provide a basis for choosing appropriate pile types and reliably estimating pile lengths for projects in this terrain. Bridge foundation design projects in other mountainous terrain share similar design and construction challenges to those encountered in these Vermont projects. These include: difficult exploration drill rig access requiring smaller rigs with limited capability to drill through cobbles and boulders deep enough to reach bedrock; limited experience with displacement piles as alternatives to H-piles in this geology; and relatively greater variability in soil stratigraphy between foundations at these sites as a consequence of the relatively high energy depositional environment in mountainous terrain. This paper presents the case history summaries of the pile driving, results of the ?back analysis? capacity evaluations, examples of solutions employed on these projects to address the lower capacities achieved, and resulting pile capacity design guidelines and prediction criteria for these geologic conditions based on data from these projects.

Jan 1, 2007

By J. Erik Loehr, Andrew Z. Boeckmann

"Poor drainage is a common cause of poor performance of earth retention systems, resulting in burdensome serviceability problems that can progress to outright failure of the retention system if not addressed. A drainage system consisting of filtered conical drains that can be installed through the face of an existing retaining wall and readily maintained was evaluated through tests of physical and numerical models. The physical models were constructed with different backfill materials in a container measuring 8 ft wide by 4 ft tall by 15 ft long. Tests were conducted by saturating the backfill under a constant water elevation atop the model, and then maintaining the water elevation until seepage from the drains reached a steady state condition. Pore pressures within the backfill and outflow from the drains were measured to facilitate calibration of numerical models that accompany the physical models. Results from the calibrated finite element models were used to develop design criteria for the drains. The design criteria establish the required drain spacing as a function of the height of groundwater above the drains and the diameter of the drain.INTRODUCTIONMany retaining wall performance problems are a result of poor drainage of the wall backfill. Consequences of poorly drained backfill include displacement and rotation of the wall face, including the extreme case of collapse, and seepage through the face of the wall, which is in turn associated with damage from corrosion, dry rot, and other forms of deterioration. A common approach to improve drainage of an existing wall is the installation of drainage features (e.g. “weep holes”) in the face of the retaining wall. Weep holes facilitate controlled seepage through the face, which relieves water pressure within the backfill and directs seepage to known locations in the wall face. Although installation of weep holes is relatively common, engineering methodologies for selecting the size (diameter) and spacing (along the wall) of facial drainage features are uncommon if not altogether non-existent. This paper documents tests of physical and numerical models of retaining walls with facial drainage features, including conventional weep holes as well as maintainable drains installed through the face and extending into the wall backfill. Results of the testing were used to develop generic design criteria, which establish the required drain spacing as a function of the height of groundwater above the drains and the diameter of the drain."

Jan 1, 2016

By Stefan Dahlin

The laboratory tests indicated low permeability but as I said, as a rule, the permeability in the field has been found to be higher. A high permeability has also been found when doing back calculations of rates of settlements in different cases. But as I also said, there's a need for further studies in this area.

Feb 10, 2003

By Hiren J. Shah

Across much of New York City, the geology of glacially deposited soils follows a common sequence. Outwash sands generally overlie varved silts and clays, which lie above a basal till deposit underlain by the bedrock. Pile foundations at projects with such typical stratigraphy generally develop their axial capacities by extending below the fine-grained deposits into the till or the bedrock. Contrastingly, at a project site on the Brooklyn waterfront, high capacity piles were efficiently and economically installed by driving them into the relatively shallow glacial drift and till deposits which lay above thick fine-grained compressible glacial lake deposits. An unusual aspect about the foundation design at the Brooklyn project site is that, relatively short and high capacity piles were driven into the shallow glacial drift and till deposits, overlying the thick fine-grained glacial lake deposits. In order for this unusual foundation scheme to be feasible and economical, the piles needed to achieve their driving criteria in the upper strata. Consolidation settlements in the lower stiff and over-consolidated glacial lake deposits below the pile tips had to be relatively small. The paper discusses the unusual stratigraphy in this area of Brooklyn in greater detail with geologic profiles and engineering characteristics of the glacial strata. It also discusses the design aspects of the pile foundations, settlement estimates, a pile drive test program during design, results of the static load test program during construction, and production pile installation results.

Jan 1, 2008

By Lucian L. Bogdan

"SummaryActive loaded strand anchors are often used for slope stabilization, retaining walls or tiedown anchors. Normally, strands are tensioned against the structure and wedges are locked inside the anchorages at a certain lock-off load. During the life of the structure, anchors can receive additional loading during a surcharge, seismic event or other activity on the structure.In order to have a reliable ground anchor system, the strand must not slip through the anchorage wedges during its service life. Strand slippage has been reported during lock-off, when dirty wedge plates and wedges have been used. Low lock-off loads are believed to contribute to strand slippage too. Since the initial lock-off load for a ground anchor is usually lower than the lock-load for an equivalent capacity tendon in other types of post-tensioning construction, there is a concern that strand slippage may occur if the load on the anchor increases above the initial lock-off load.Corrosion protection grout, placed after the anchor is locked off, fills the pocket and surrounds the strand and wedges. Some anchor installers believe that the grout will prevent the anchorage from developing additional capacity if the load increases above the initial lock-off load.The load-carrying capacity of an anchorage depends on several factors. Most important are: initial applied load, anchorage geometry, friction between wedge-anchorage-strand and condition of the contact surfaces.The ADSC Anchored Earth Retention Committee considers that the industry should know how wedges behave once the permanent strand anchors are stressed and grouted inside the transition pipe, between wedges and inside the grout cap."

Jan 1, 2005

By F. M. Abdrabbo

Flight auger bored piles are formed by screwing a continuous flight auger into the ground, and pumping cement/sand grout or concrete down the hollow stem of the auger as its withdrawn. The auger is driven at the top by hydraulic or electrical motor and is guided by a vertical crane leader. Loading tests on concrete piles are described. The stability plot method is used to drive the shaft friction and the end bearing load components of the pile capacity. This paper outlines features of crucial construction factors that affect the geotechnical capacity of this type of piles. These factors include, vertical speed of auger during boring, grout factor, grout pressure, number of reborings, type of material, and slump of concrete used to form the piles. Two of these factors are highlighted in this paper. It was found that, shaft resistance is independent of grout factor, whilst point resistance increases as grout factor increases. Nevertheless the engineer should decide the safe pile load associated with the most economical grout factor. High vertical speed of auger during boring of piles may cause disaster for the adjacent buildings, due to soil decompression.

Jan 1, 1993

By Paul Pedini

The challenge of Contract C19E1 of Boston's Central Artery Project called for the construction of two roadways under the commuter rail yard at North Station. Two options were offered for the method of their construction: Slurry Wall Roof-First or Soft Ground Tunneling. The instability of the indigenous soils seemed to rule out the use of tunneling, so the slurry wall method was chosen. However, these soils were incapable of holding up during slurry trench excavation. After many episodes of ground loss on early panel excavations, Modem Continental Construction suggested a method of trench wall stabilization. The Contractor (MCC) both suggested wall stabilization method and requested that the owner participate in the funding for the effort. The Project and the Contractor were able to agree on a solution which resulted in collapse-free excavation...and found an innovative way to fund the solution.

Jan 1, 2002

By Rouzbeh Afsharhasani, Moses Karakouzian, Brandon Kluzniak

"The Vegas High Roller is the centerpiece of a new development parcel adjacent to the Las Vegas Strip. At a height of 550 feet, the High Roller is currently the tallest observation wheel in the world. The design team conducted a geotechnical site investigation to characterize the alluvial soils and cemented layers encountered and to provide foundation design recommendations for the observation wheel, boarding platform, and temporary structures needed to erect the wheel structure. This paper presents a case history of the geotechnical design process, including development of a ground model and design parameters, high-strain dynamic axial load tests, and settlement monitoring during construction. Results indicated that design parameters were conservatively assumed and that the majority of the axial load was transferred to a near surface caliche layer, thereby resulting in insignificant settlement of the foundation system.IntroductionThe engineering of the Vegas High Roller is similar in concept to that of the London Eye and the Singapore Flyer. The wheel has 28 cabins, each with a capacity of 40 persons. The top point of the structure is 550 ft above ground level at the site.A geotechnical site investigation program was undertaken and subsequent analyses were performed to provide foundation recommendations for the observation wheel legs, boarding platform columns, and temporary structures directly associated with construction of the observation wheel."

Jan 1, 2017

By Daniel Ruffing, Charlie Krug

In recent years, the chain-style trencher has been proven a valuable tool for installing vertical walls on challenging sites where conventional methods may be less desirable. Like many tools, trenchers are most effective when used with the right application. Trenchers are commonly used for applications that could also be completed with conventional slurry trenching; low-permeability cutoff walls, collection trenches and permeable reactive barriers (PRBs). Drawing from a wealth of experience with conventional slurry trenching and the trencher, this paper compares and contrasts the technical considerations, treatability, installation, performance, and lessons learned for recent projects.

By Adrian M. Keller

Borehole televiewers are downhole inspection devices available for high-resolution imaging of a borehole wall following rock coring. Borehole televiewers should be considered by geotechnical engineers and geologists as a supplemental way of investigating rock for deep foundations. The optical televiewer (OTV) produces a digital optical image and the acoustic televiewer (ATV) utilizes reflected acoustic waves to produce images of the borehole walls. These devices can be utilized to examine soft or fractured zones in the rock mass, solution features, open joints or other voids not observable from traditional rock coring techniques. These devices along with computer post-processing can determine the strike and dip of joints, bedding planes, shear surfaces, or other structural features, eliminating the need for expensive oriented cores or manned downhole logging. An acoustic televiewer was utilized in the Fall of 2008 during the investigation phase for the I-70 New Mississippi River Bridge (I-70 MRB) in St. Louis, Missouri. Voids and fractures in the upper portion of the rock were described by prior consultants. Further investigation of these features was necessary to evaluate deep foundation options to support the main towers. Ten borings were drilled from a barge in the river at the two main tower pier locations. An ATV was utilized in each of the ten borings to produce images of the rock mass in the borehole and allow further investigation of the voids. Voids interpreted as solution features were readily identified in the ATV logs in multiple borings and at similar elevations, suggesting connectivity. Measurements of the voids? width, location in the borehole and orientation allowed a more thorough understanding of the potential impact the solution features may have on the planned deep foundations. An extensive grouting program was eliminated based on the ATV results.

Jan 1, 2010

By Dale Berner, Michael O’Sullivan

"This article focuses on lessons learned from innovative designs including in-the-wet construction methodology and modified foundation conditions, for two United States Army Corps of Engineers (USACE) megaprojects. Olmsted Dam FoundationThe over $2 billion Olmsted Dam on the Ohio River is currently under construction 16 mi (29.6 km) upstream from the confluence with the Mississippi River. The project is under the jurisdiction of the Louisville District of the USACE. It will consist of an 800 ft (244 m) long tainter gate section, a 1,400 ft (427 m) navigable pass, two boat abutment sections, a fixed weir section, and upstream and downstream scour protection. The Olmsted Dam and its two 1,200 ft (366 m) locks, which were built in 2002, will eventually replace both Locks and Dam #52 and #53, both built in 1929, and thereby bring significant benefits to the Ohio River navigation system.In 2002, the Jacobs/COWI JV completed the design of the dam; which was an engineering challenge for several reasons. A significant consideration was its proximity to the New Madrid Fault, which could impose an 8.4 Richter scale seismic event on the structure, which is located in an area of potentially liquefiable alluvium. The extensive seismic analysis performed by the designer included a response spectra analyses, lateral pushover analyses of pile foundations, hydrodynamic added masses, pile group effects, and the development of kinematic motions as a result of the soil-pilestructure interaction."

Jan 1, 2016

By J. P. Powers

Methods for dewatering and the control of ground water for construction and mining are discussed, including open pumping; predrainage with deep wells, wellpoints or other systems; cutoff or exclusion of water by steel sheet piling, slurry concrete walls and slurry trenching, grouting, ground freezing, compressed air, slurry shields and earth pressure balance shields. Criteria are given for the selection among the methods for a given project. Unwanted side effects of dewatering are listed, with procedures for evaluating and avoiding them, by cutoff or artificial recharge.

Jan 1, 2010

By H. S. Radhakrishna

Foundations supporting power transmission and communications towers are subjected to both compression and uplift loads, often of a cyclic nature. Some novel foundations, combining the beneficial features of grouted and helix anchors with that of compression piles and grillages, were developed by Ontario Hydro during the construction of high voltage transmission lines in Ontario, Canada. In addition to meeting the load requirements, the foundations permit easy installation in swampy areas and also minimize impact on environmentally sensitive terrain. This paper describes the features of these composite foundations and outlines the performance criteria used for their design and installation on the basis of load test results.

Jan 1, 2010

By Jacob A. Jordan, Rachel M. Garrett, W. Robert Thompson III, James C. Pegues

"Environmental control structures for an existing fossil-fuel power generating plant near Pascagoula, Mississippi faced several design and construction challenges due to space limitations. Conceptual design calculations indicated drilled shaft foundations would likely be needed to accommodate the higher lateral and compressive loads expected under some structures. A maximum drilled shaft diameter of 60-in was preferred due to various space constraints. Smaller diameter drilled shafts were deemed acceptable under structures with more moderate loading conditions. Furthermore, augercast piles were considered where lateral loading was not a governing design criterion.A series of SPT borings and CPT soundings revealed a subsurface profile consisting of soft to firm clays to depths of about 25 feet, underlain by fine to coarse sands. The apparent relative density of the sands was loose just below the clay, with increasing density noted with an increase in depth.Analysis of conventional drilled shafts indicated needed capacities could not be achieved unless shaft lengths exceeded 100 feet. Post-grouted drilled shafts were therefore evaluated to decrease shaft lengths by taking advantage of increased base capacity. Analyses showed the higher predicted capacities needed for some structures could be achieved with this approach. Final design for the project incorporated 90-ft long, 60-in diameter post-grouted drilled shafts; 60-ft long, 48-in diameter post-grouted drilled shafts; and 60-ft long, 48-in diameter conventional shafts. Both post-grouted and conventional trial shafts were installed as part of the detailed design phase of the project. Each trial shaft included CSL integrity testing and Osterberg-cell bi-directional load testing. Load test results revealed that additional base capacity was, in fact, achieved through the post grouting process. The 60-in diameter post-grouted production shafts and the 48-in diameter conventional production shafts have been installed at the site, with the project that would utilize the 48-in diameter post-grouted shafts deferred at this time."

Jan 1, 2015

By D. Dreher Whetstone, Paul M. Blakita, Christopher M. Reith, Ravi P. Malviya

"Micro-piles are small diameter (5 to 10 inches), cast-in-place piles which can develop high load capacities by bonding with soil or rock. Micro-piles are particularly well-suited for moderate to heavily loaded structures requiring deep foundations in difficult subsurface conditions, such as karst, bouldery mine spoil, or unsuitable fills with concrete debris or other obstructions. Attempts to install conventional deep foundations including driven piles, drilled piers, or auger-cast piles are likely to be fraught with construction difficulties and disputes, delays, cost overruns, and may be unfeasible in some cases. Micro-pile installation equipment is very effective in installing foundations through such overburden or rock materials.This paper presents case histories of Micro-pile installations on two projects with difficult soil/rock materials. The project sites are located in Charles Town, West Virginia and Masontown, Pennsylvania.Charles Town, West Virginia ProjectThe Charles Town project entailed construction of a four-story pre-cast concrete garage. Triad Engineering, Inc. performed a geotechnical investigation for this project (Triad, 2001). The subsurface, geologic, and project specific information described in th is paper are largely based on the aforementioned geotechnical report.Ground ConditionsThe project site is located in Jefferson County, West Virginia, and is mapped to be underlain by the Elbrook Formation. This formation is described as argillaceous, dolomitic limestone with beds of dolomite and aphanitic and algal limestone (Dean, et al. , 1990). The carbonate rocks at the site were characterized as ""moderately solution-prone, highly calcareous and weathers differentially to produce a pinnacled or ""sawtooth"" top of rock profile. (Triad, 2001 )"" Overburden soils consist of low to high plasticity, fine grained residual soils formed by weathering of the parent carbonate rock. The residual soils include variable proportion of sand and rock fragments."

Jan 1, 2005