Search Documents

By Roderic A. Ellman

The new Woodrow Wilson Bridge (WWB) will replace the existing bridge over the Potomac River to connect Alexandria, Virginia to Prince Georges County, Maryland. The new WWB will extend approximately 1.1 miles across the river, with a 367-ft long bascule span in the main river channel where the water depth is about 36 ft. The subsurface soil profile consists of up to 50 ft of a soft organic silty clay layer that is very vulnerable to scour, underlain by a deep deposit of hard sandy clay. Foundation construction in the Potomac River required the use of cofferdams to allow structural concrete work to be performed in the dry. This paper will the present the types of cofferdams used to construct the foundations for the WWB replacement project. The bridge is primarily comprised of fixed spans in relatively shallow water and a bascule span over a navigation channel in relatively deep water. Foundation construction included the installation of 48" to 72" open end steel pipe piles and cast-in-place concrete pile caps. To achieve the desired bridge appearance, pile caps were required to extend below the water surface and below the existing river bottom in shallow water locations. Conventional steel sheet pile cofferdams with tremie concrete seal were used to construct fixed span, shallow water piers. Selection of deep water bascule span foundation cofferdams was governed by several factors including contraction scour, environmental considerations and cost. Potomac River cofferdams, i.e., relatively shallow depth cofferdams that are supported by the foundation piling were selected. This cofferdam system provided a shallow profile which minimized contraction scour and the amount of filling in the river. Design issues include load selection and cofferdam stability in very soft alluvial soils. Construction issues include erection sequence, tremie concrete mix design and placement procedures.

Jan 1, 2005

By X. L. Chen

The diaphragm walling has been recently adopted in one of the largest excavation of deep foundation engineerings in Shanghai, China with dimension of 90m in length, 50m in width and 13m in depth to solve its stability problem. In this paper the field test for monitoring the stability of the diaphragm wall is discribed, in which the excess pore water pressure and the horizontal displacement of the clay layers were monitored during the period of the excavation. The data measured in the field test are efficient for the safety during construction.

Jan 1, 2010

By Ben C. Gerwick

Large diameter steel tubular piles installed vertically or on a slight rake, offer many advantages as the foundations of major overwater bridge in regions of high seismicity. By proper selection of diameter and wall thickness, an optimum balance between stiffness and strength can be achieved. Under strong seismic motion, the piles will deflect and bend so as to reduce the acceleration forces transmitted to the superstructure, while still limiting drift. A major advantage of this concept is that the mass of the footing block is significantly reduced from that of the conventional pier. The design of the footing block requires great care in order to transfer the high shears and moments. Where the soils consist of significant depths of sediments, the kinematic interaction of soils, piles and structures must be considered. Moments will be a maximum just under the footing block. Filling the top portion of the pile with concrete will prevent local buckling and assure ductile behavior even under overload. Typically the piles will be long, with most or all of their support furnished by friction and will require the use of very large pile hammers to achieve the required capacities. Where the piles are founded on rock or in hardpan, sockets will be drilled and filled with reinforced concrete. For these piles, high moments can occur both at the head and just below the rock surface, so the concrete infill should extend the full length. This paper describes the use of tubular piles driven through the deep silty sands of the Jamuna River, Bangladesh, and also where socketed into the near-surface rock for the mail pylon pier of the new San Francisco-Oakland East Bay Bridge in California.

Jan 1, 2013

By Waddah Akili

This paper describes the steps taken in planning, developing, and executing a case study/ case history course in geotechnical/ foundation engineering at an international university. The paper sheds light on: how a “workable” format for the course was arrived at; the organization of the course; and the results of evaluating the effectiveness of this approach versus traditional lecturing. Problems and challenges that could arise when offering the course for the first time are also addressed. Embedded in this experience and its related protocols are: the emphases on engineering design and the practice, teamwork and leadership development, organizational management, and oral and written communication skills. The paper concludes by confirming that discussions, through an open forum, are judged to be superior to traditional lectures in improving critical thinking, cultivating desirable personal attributes, and acquiring problem-solving skills.

By Gary L. Seider

Chance, a Division of Hubbell Power Systems, Inc., in conjunction with Sailors Engineering, Inc. has updated its Helical Design Capacity Software. This latest version, ?HeliCAP® v2.0?, is a state-of-the-art helical anchor and pile capacity program designed to operate in the Microsoft® environment. The program calculates the tension and compression capacity along with the frictional capacity, if applicable, of CHANCE® Civil Construction helical anchors and piles using design theories and methods adopted by Chance. This paper details the current state of practice employed by the software in the design methods and installation methodologies of helical anchors and piles.

Jan 1, 2007

By Denis Huber

The technical assessment of the final works on the "Stéphany Palace" project at Menton in France's Alpes-Maritimes region shows the importance of daily project monitoring based on the observation method recommended by the European standard Eurocode 7 which applies to Foundations and Geotechnical Engineering. Excavation operations to a depth of 10 m near the France-Italy railway track and adjacent buildings required precise observation of land deformations, regular piezometric monitoring as well as special design arrangements. Temporary active tie-rods were thus placed in phases in order to control deformations in the retaining structures resulting from excavation operations. The Menton region, terminating the Alpine arc of mountains, naturally required the consideration of seismic forces in phase in the lower floors of the building, directly linked to the buried walls. These calculations were carried out in accordance with the PS69/92 rules, calling for an increase in dynamic thrust under the effect of gravity field rotation.

Jan 1, 2002

By Anne Fagot

Because of the risk of corrosion caused by stray currents, steel foundations and steel sheet piling are generally prohibited in the vicinity of railway structures. Steel solutions are only accepted if they are shown to meet the required design working life and if this can be achieved at an acceptable cost compared to competing materials. The influence of stray currents on various steel sheet piling designs was studied using software initially dedicated to gas and pipeline industries and cathodic protection systems. It has been successfully adapted to model stray currents affecting steel sheet piling. Corrosion rates assessed using this modeling software were considerably lower than commonly expected. Zones of potential corrosion risk were identified; specific cost-effective countermeasures could be established. The developed software tool can help to optimize the design of piling solutions in the vicinity of DC railway power systems in terms of suitable countermeasures that meet structural reliability and cost requirements.

Jan 1, 2008

By John Erikson, Alan J. Lutenegger, Nicholas Williams

"In order to evaluate the level of disturbance produced in clays during installation, a series of single-helix and multi-helix anchors were installed at a test site consisting of a stiff overconsolidated clay crust overlying softer near normally consolidated clay. Field vane tests were then conducted over the top of the helical plates at various depths to determine the undrained shear strength after installation and were compared with undrained shear strength measured in adjacent undisturbed ground. The tests represent the first time that the degree of installation disturbance has been evaluated directly and show that even with perfect installation practice the clay is disturbed as a result of rotation of the helices during installation. The results show that the soil is not completely remolded but that the strength is below the peak undrained strength of the adjacent undisturbed ground. Measurement of the installation torque and the rate of advance are used to define an “Installation Disturbance Factor” which may help to evaluate the quality of the installation by the Contractor and degree of soil disturbance. INTRODUCTIONAn important consideration in the design of Helical Anchors is the degree of disturbance to the soil during installation. This may be especially important for saturated fine-grained soils where the disturbance from installation may produce a reduction of the undrained shear strength. Even though this was recognized as early as 1950 by Skempton, soil disturbance is often ignored by engineers using current design procedures. Field investigations were performed to obtain both directs and indirect evaluation of the degree of disturbance produced by the installation of single-helix and multi-helix anchors in clay and the influence of disturbance on behavior. The investigations involved measurement of torque and advance during installation, load tests performed to determine load-displacement behavior and ultimate capacity and field vane tests performed over the helical anchors to evaluate changes in undrained shear strength as compared to adjacent undisturbed ground. The characteristics of the site and details of the installation are presented. Results of the field vane tests are shown for a number of helical anchor installations and results of load tests are presented. The results indicate that a reduction should be made to the undisturbed undrained shear strength for design and that the reduction may be related to the Sensitivity of the clay and quality of installation."

Jan 1, 2017

By Mary Ellen Bruce

Let me first address the issue of the wet grab samples. The wet grab samples that were attempted to take on the Central Artery were hindered by the fact that the way the mixing was being done was only by injecting grout on the way out, during withdrawal of the mixing tools. They would auger down to the required depth (usually with some water being injected), which took anywhere from 45 minutes to an hour, and then when coming out, the grout would be injected with grout. That was leaving a column of grout in the center where the shaft had been (i.e. inside of the blades of the mixing tools), which would end up being something like a foot in diameter because the pipe that was used for the drill shaft was a foot in diameter. So we had 10 inches to a foot of almost pure grout in the middle of our column and then we had 2 feet on either side that was mixed soil cement. So when they went down with the wet grab sampler not knowing where that was in the column sometimes they/we were getting strengths of 1500 psi, and sometimes they/we were getting strength of 500 psi or 100 psi. So what was it that we were taking into the wet grab sampler? In those cases you don't really know, but it wasn't representative of the core samples we were taking. We were purposely not coring in the center because we knew that was going to be high cement content, almost pure grout. So the issue of wet grab sampling particularly on this project, the Central Artery Project, was that we didn't really know what we were sampling. What becomes an issue with wet grab sampling in other projects is that you have to have another device (machine) in most cases, a cherry picker crane or something similar that can raise and lower with a beam that is used to forces the sampler down into the freshly mixed soil-cement. And regarding economics, is it more economical to have that crane standing by with its operator or to have a drill rig to come along later and do the coring and take the material out that's fairly identical to what you're finding in situ? The complaint of micro-fracturing in the core samples as you're taking the cores was raised by Seiko as causing large strength reductions. But, if you're doing it carefully, then I don't think that's much of an issue anymore, on research basis perhaps but not on a practical level.

Feb 10, 2003

By Paul W. Mayne

The axial load-displacement-capacity and load-transfer response of deep foundations can be conveniently assessed by geophysical piezocone tests that provide four independent readings with depth, including tip stress (qt), sleeve friction (fs), porewater pressures (ub), and shear wave velocity (Vs). The penetration data (qt, fs, and ub) of the CPT are utilized to obtain the pile side friction (fp) and end bearing capacity (qb) while the shear wave measurements provide the initial stiffness. Within an elastic continuum framework, the axial pile deflections are calculated and an approximate nonlinear response is obtained by modulus degradation from small-strain response (G0) to intermediate- and large-strains (G). The continuum solution permits separation of load transfer along the sides and proportion to the base. Applications are shown for case studies involving an end-bearing drilled shaft, two friction-type drilled shafts in Alabama and Georgia, and a "Class A" prediction involving driven pipe piles in residuum of the Atlantic Piedmont geology. Load-transfer data were available for the drilled shaft foundations.

Jan 1, 2002

By Fei-chiu Huang

A 17-acre landslide occurred in February 2001, on a slope below Via Bellota in the City of San Clemente, California. Three homes were destroyed and many others placed in jeopardy. The landslide, involving portions of five separate developments, continued to move significantly in the years following. Litigation ensued among the affected parties, and investigations continued through 2007. A mediated repair resolution was ultimately reached among the parties. The agreed upon repair consists of a multi-million dollar stabilization program that included grading, drainage, and structural systems. Part of the construction cost was offset by creating 4 new ocean view custom lots and 20 new mobile home lots. The landslide repair and slope stabilization design involved removal and replacement of portions of the landslide debris and construction of buttress and stabilization fills as well as installation of 74 shear pins in two rows. The shear pins were designed as 4-foot diameter by 50 feet in length and incorporated continuous W30x211 wide flange steel. The shear pins were designed to be installed 25 feet above the slide plane and 25 feet below the slide plane at each location. Construction of the 74 shear pins was initiated in 2008 and completed in 2009. Four-foot diameter holes were drilled by utilizing a truck-mounted, flight-auger-style drilling rig with a 4-foot diameter solid-flight auger. Prior to the installation of the shear pins, an engineering geologist downhole logged strategically selected holes to further evaluate the actual slide plane elevations. The wide flange steel shear pins were then lowered to the desired elevations and encased within 4,500 psi, Type V, 0.45 maximum water/cement ratio concrete. Inclinometers installed within four pin shafts and behind the pin rows indicated performance in accordance with the design. Slight to non-perceivable shear displacement was measured which mobilized the intended capacity at the monitored shear pins. No excessive slope movement was detected at any of the inclinometer locations during or after the construction period. Actual shear displacement of the steel wide flange elements was less than the movement anticipated before shear pin installation.

Jan 1, 2010

By Jeffrey A. Gebhard

As part of the design and construction of the new St. Anthony Falls I-35W Bridge, a full-scale load test was conducted on a 6 1/2-foot diameter drilled shaft in the St. Peter Sandstone. This load test helped identify shaft-rock interaction properties, including end bearing and multiple zones of differing shaft resistance for design of the drilled shafts beneath the three piers adjacent the river. The load test was designed by Load Test, Inc., Braun Intertec and the design team of Figg Bridge Engineers/TKDA and constructed by Design Build Consortium of Flatiron/Manson. Oversight was provided by the Minnesota Department of Transportation. Based on these test results, the drilled shafts supporting the St. Anthony Falls I-35W Bridge were designed to reduce risk and maximize economy for the people of the State of Minnesota.

Jan 1, 2009

By Garland Likins

The Texas Department of Transportation, now considering using Augered Cast-In-Place (ACIP) Piles (also known as Continuous-Flight-Auger or CFA Piles) in their foundations, awarded a research project to Professor Mike O'Neill at the University of Houston (UH) to study the advantages and potential difficulties with ACIP/CFA piles. ACIP/CFA piles were installed on three sites for UH; they had extra instrumentation and additional measurements by UH staff during installation which are beyond the scope of this paper. Independent visual logging of the pile was done by an experienced inspection firm. The main advantages of ACIP/CFA piles are their speed of installation and their economy. Potential savings are substantial. Disadvantages include an unknown structural condition of the shaft. Inspection is critical, but many simultaneous observations make accurate inspection difficult. Because of resulting uncertainty, many engineers have avoided ACIP/CFA piles in the past.

Jan 1, 1998

By Sam Messina

[Project: Job Number: Date: Superintendent: Person Making Inspection: Note: The following checklist shall be used on a regular basis as an overall assessment of the jobsite. The checklist is not all-inclusive. All applicable Federal, State, and local regulations, standards, and ordinances pertinent to the jobsite conditions must be evaluated on a continuous basis. Column A - Adequate Column I ? Inadequate]

Jan 1, 1998

By Anand J. Puppala

This paper provides information on various evaluation studies conducted to assess the CPT based interpretation methods. Salient findings from these evaluations are summarized. Additionally, a comprehensive evaluation study on both LCPC and European methods was performed on twenty-four driven piles selected from four different states. This evaluation showed that the LCPC method predictions are close to measured pile capacities. The European method provided good predictions for driven steel piles. Overall, both methods' predictions show high values of coefficients of variations, which are in agreement with other studies. Overestimation of driven concrete pile capacities is attributed to large estimations of unit point resistance. Suggestions to consider appropriate CPT based pile capacity interpretation methods are presented.

Jan 1, 2002

By B. Francis

Literature provides only limited information regarding the behaviour of laterally loaded piles socketed into weak rock masses. A laboratory program, comprising a number of tests of scaled models of the pile/rock mass system has been conducted. A synthetic rock, known as Johnstone was used to simulate a naturally weathered and fractured siltstone. The load-deflection behaviour of the test piles was measured, and strain gauges were fixed to the model piles to assess the bending moments. The laboratory results are compared with the results from several theoretical models, some of which are in the form of commercial software packages. This study highlights the inadequacy of existing methods to adequately model the influence of rock joint orientation in geotechnical design. Additionally, numerical modelling of the pile/rock mass system was carried out using the discrete element program UDEC. The importance in modelling the system using discontinuum mechanics is highlighted, particularly to capture the anisotropy of the rock mass.

Jan 1, 2004

By James D. Hussin

The Florida limestone is a relatively soft rock which presents many challenges to engineers when designing deep foundations. One alternative is micropiles which have grown significantly from their early days as very small diameter, light capacity elements. Also known as minipiles, pin piles, needle piles or root piles, micropiles offer an attractive deep foundation alternative for sites with tight access, low headroom, and where difficult subsurface conditions or obstructions necessitate a small diameter, high capacity deep foundation. The ability to confirm the competence of the limestone bearing formation by drilling in a rock socket has made micropiles a growing deep foundation selection in Florida.

Jan 1, 2003

By Jason N. Scott

It is now possible using low-cost wireless technology and rugged hand-held devices to record data on site electronically and for that data to be instantly available to others. This could potentially eliminate many problems that traditionally lead to remedial work, such as poor communication and the late detection of non­conformances. However, determining how best to implement such a system and integrate it with the rest of the business process is far from simple. This paper looks at Stent's experience of these issues by way of a case study of the SHERPA system. This is a wireless site data collection system developed for use with rotary bored piling.

Jan 1, 2006

By Edwin W. Hickey

This paper briefly discusses the geologic conditions in South Florida relative to the design, construction, and performance of deep foundations. The subsurface conditions in this area are unique in that the rock layers are highly porous and often very soft, and are sandwiched between layers of typically loose, uncemented quartz fine sands. Due to the high porosity of the Miami Limestone, 4-inch diameter rock coring is often required to obtain intact samples, and dewatering of excavations is sometimes difficult or impossible. The sand layers, typically tens of feet thick, are very loose to loose in relative density and have been the cause of unexpected large, deep foundation settlements. The engineering properties of the various geologic formations are discussed, along with typical deep foundation types used in the Miami area prior to and after 1980.

Jan 1, 2003

By Lisheng Shao

Soil mixing and jet grouting have been widely used to support heavy structures such as tanks, cement silos, and storage buildings. Although the installation methods vary between soil mixing and jet grouting, the end product of soil-cement columns behaves similarly in supporting structure loads. In many cases, soil-cement mass treatment offers the owner savings over driven/drilled piles. This paper discusses the design methodology, production work, and quality control, with supporting figures, of a recent large complex tank farm project. The project consisted of constructing six above-ground steel storage tanks and an approximately 700-foot-long fill slope. The tank farm site is located in an industrial area of southern California, with highly variable subsurface conditions consisting of compressible soils and buried construction debris. The compressible soils necessitated that the new tanks be supported on deep foundations. A test pile program performed previously at the site showed that conventional driven concrete piles were not feasible because of buried construction debris, therefore a soilcrete system was proposed. Site design included evaluating the total and differential settlement and column group bearing capacity under both static and seismic loads. Extensive field and laboratory testing confirmed the design soil-cement strength and modulus of both the soil mixed and jet grouted soil-cement columns. The project operation and quality control programs are also included in this paper.

Jan 1, 2010