Search Documents

By C. A. Pickles

Nickeliferous limonitic laterite ores contain considerable free moisture. In this research, the application of microwave radiation for the drying of this ore was investigated. The effects of sample mass, initial moisture content and porosity on the microwave drying rate were studied and the results were compared to those obtained with conventional drying. Microwave drying rates of two to three times the conventional values were achieved. Further enhancement of the microwave drying rate was realized by increasing the flow rate of air over the sample or by operating at reduced pressure. The high microwave drying rates were attributed to the inverted temperature gradient which resulted in internal heating and boiling and this in turn promoted movement of the water, both as liquid and vapour, to the surface.

Jan 1, 2005

By Karl Houseley, Dr. Robert J. Chapman

"A gravity concentration process has been applied to ores from the Clogau Mine, north Wales, the Tyndrum deposit, central Scotland and an alluvial ore from Leadhills area of Scotland. In the case of the Welsh ore and the alluvial deposit the gold grains in the concentrate and tailings streams have been characterised in terms of their three dimensions.In the case of Welsh ore, the thickness of a gold grain has been shown to be the single most important factor in determining behaviour in a gravity concentration operation. Six indices were used to quantify the overall geometry of the gold grains and those which incorporate a thickness term have proven to be effective in predicting the destination of gold particles within the concentration circuit. It is proposed that the most simple of these, the Heywoods flakiness ratio, has potential for the control of milling operations as an alternative to the established practice of characterising the size of the mill discharge.The effect of grain geometry on the recovery of fine gold has been studied using Tyndrum ore. The recovery of gold by gravity concentration increased from 20% to 70% when the criteria used to design the milling operation was the prevention of over grinding of gold grains.The destination of alluvial grains in the concentration circuit did not show such dependence on shape, and this has been attributed to the effective classification of all the gold grains in the sample by fluvial action producing a population of similar geometric characteristics."

Jan 1, 1996

By D. Larouche, M. Mardan

Hot tearing is a complex defect in aluminium castings which is produced during solidification when a certain amount of liquid phase remains and weakens tensile resistance of the alloy. In direct chill casting of aluminium alloys, hot tears initiate at the surface of sheet ingots just after the primary cooling zone, where the microstructure is particularly vulnerable. In order to study the hot tearing susceptibility of these alloys, and the effect of grain refiners on their thermo-mechanical behavior , tensile tests were carried out in the semi-solid state ( ~95% solid) and at low strain rates using an apparatus called DCSS, for Direct Chill Surface Simulator. This apparatus, originally developed at Alcan Arvida R&D Centre (ARDC), is an instrumented rig test reproducing the conditions prevailing during the primary cooling stage of the DC casting process. The mechanical behavior of solidifying shells and the hot tear formation under applied tensile loads were measured and the occurrence of hot tearing was observed. Temperature in different locations of the casting, applied load and surface strain were monitored during the tensile tests conducted on aluminum alloys AA5182, AA6111 and AA3104. The microstructure of the tested samples was examined using the optical microscope to evaluate their columnar or equiaxed aspect and their effect on the mechanical response of the alloy. A special emphasis has been given to the evaluation of fractions solid existing in the castings at the start of the tensile tests, taking into account the local temperature, thermal gradient and cooling rates experienced. It was found that excessive grain refiner additions decreased the strength of solidifying shells because of the increased level of porosity induced by easier nucleation of new phases (gas included). It was also observed that cooling rates increased with the level of grain refiner, a phenomenon that was associated to the higher number of contact points obtained with small equiaxed grains. Finally, the concept of a stress based criterion for hot tearing was reinforced by the strengths obtained on not grain refined AA5182 and AA6111 showing similar fraction solid near the surface, but significantly different grain sizes.

Jan 1, 2006

By S. Avalos, J. M. Ortiz, W. Kracht

Semi-autogenous grinding mills are intensive energy consumers. Current models base their energy consumption inference on operational variables and feeding ore characterization. While they provide adequate design guidelines, they are not suitable for real-time energy forecasting dealing with gaps in operational dataset and up/downstream process bottlenecks. This work explores the capability of Gated Recurrent Units to learn the semi-autogenous grinding mill consumption behaviour. Gated Recurrent Units are trained to forecast different time-support consumptions under a time-series operational dataset. The results show high performance on small supports (30 minutes) to capture local variability and long-trends while larger time supports (8 hours) can only capture time-trends but not local variability. The proposed technique seems promising for further research and implementation on real mine cases since the input variables are low-cost and easy to obtain. INTRODUCTION Current changes in the Chilean energy matrix (Román-Collado, Ordoñez, & Mundaca, 2018), from fossil fuels to renewable energies, have impacted different industries and particularly the mining sector. Solar energy incorporation into greenfield/brownfield projects will help reducing costs and will lead to rethink foundational paradigms (production and processing strategies) (Pamparana et al., 2017). Also, integration of new space-time predicting tools together with automated real-time updating models are some of the main challenges in the geometallurgical framework (Ortiz et al., 2015; van den Boogaart & Tolosana-Delgado, 2018). Those contexts encourage and demand the development of tools capable of predicting the energy consumed by mining systems, being comminution the greatest energy consumer with an average close to 50% of the entire mine consumption (Cochilco, 2013). In comminution, the semi-autogenous grinding mill (SAG) represents the largest energy consumer (~10 nominal each SAG). Theoretical and empirical energy consumption models (Jnr & Morrell, 1995; Morrell, 2004; Silva & Casali, 2015) base their inferences mainly on feed/product size distributions, SAG sizing, bearing pressure, feed hardness, water addition and grinding charge level, and commonly assume steady-state and work isolated from up and downstream processes. While those techniques provide adequate design guidelines, they are not suitable to predict hourly, daily or even weekly energy consumptions on interconnected comminution circuits where upstream/downstream bottlenecks lead SAGs to operate below designed regimes. Forecasting energy consumption is required by short-term energy management, medium and long-term planning energy consumption, designing the nominal capacity of renewable energy sources, among other. Also, when models are input-sensitive and some of those input measurements are expensive and/or time consuming, model robustness suffers when real-time predictions are required.

Jan 1, 2019

By T. Tsutsumi, S. Kukino

"During the diametrical compression test, the tensile stress generated near the loading plate is influenced by the contact area between the loading plates and specimen. However, very few studies have determined the contact area. Theoretical or analytical models have shown that for an orthotropic material (i.e., with material properties that differ along each of three mutually orthogonal twofold axes), the maximum tensile stress is generated at the center of disk when the angle of the principal material direction to the loading direction is close to ?/4. The maximum value is almost constant, regardless of the contact area. Conversely, the maximum tensile stress is generated near the loading plate when the angle between the principal material direction and loading direction is small. The maximum value decreases as the contact area increases. Therefore, in the latter case, the influence of the contact area on tensile strength measurement of is significant.In previous studies, the distribution of stresses applied on the loading plate is assumed to be a uniform load. In reality, the applied stress is highest at the center of loading plate and seems to decrease with distance from center. The applied load disappears at the edge of loading plates. In this study, in order to satisfy this boundary condition on the loading plate, the cosine curve is adopted as the distribution of load applied on the loading plates in a theoretical model of the diametrical compression test. Furthermore, the elastic solution using boundary conditions shown in this study is used to obtain the tensile stress distributions on the loading axis for an orthotropic circular plane. These distributions are compared with empirical results obtained under uniform loading with a loading plate or concentrated loading in previous studies."

Jan 1, 2015

By Wouter Bleeker, Isabelle Cadieux

"Abstracts of theses related to mineral deposit studies and exploration, completed at geology or earth science departments of Canadian universities, have been compiled for the period 1991 to mid-I993. Part I, presented in the June, 1994 issue of the ClM Bulletin, gave a listing of thesis titles. Part II, which consists of edited abstracts of theses considered to be of direct application to mineral deposit studies and exploration, is presented under various themes as follows:A. Kimberlites, Other Alkaline Intrusions and Related Studies;B. Volcanogenic Massive Sulphide Deposits and Related Studies;C. Mineral Economics;D. Mesothermal Gold Deposits, Other Gold Deposits and Related Studies;E. Magmatic Nickel-Copper, Platinum Group Element, and Chromite Deposits and Miscellaneous Platinum Group-related Studies;F. Granite and Pegmatite-related Deposits and Porphyry Deposits;G. Diverse Hydrothermal Deposits. Sediment-hosted CopperDeposits and Mississippi Valley Type Lead-Zinc Deposits; andH. UranitnlHeiated studies, Evaporites and Exploration Geophysics.Abstracts related to themes A to D were presented in previous issues of the ClM Bulletin, abstracts related to themes E and F are presented in this issue. The remaining abstracts will be presented in a future issue."

Jan 1, 1994

By Ken Woloschuk

??Owners?Perspective ??Owners?Challenges ??EcoNomics?Delivery Model ??Projects ??Project Outcomes ??Questions ??Balancing the triple bottom line initiative: ?shareholders expectations of economic costs and benefit; ?stakeholders expectations of social and environmental costs and benefits; ?deciding what is sustainable and which design alternatives are the most sustainable. ?? Delivering required project outcomes

May 1, 2008

By Rufus L. Chaney

A new technology is available to the Ni mining and remediation community to “phytomine” Ni from mineralized or contaminated soils using rare plants which hyperaccumulate Ni to over 1% of shoot dry matter. Research has identified useful plant species, and even bred improved cultivars of Alyssum murale and Alyssum corsicum for commercial phytomining in temperate regions. All agronomic practices (fertilization, soil amendments, planting and harvest methods) needed for economic phytomining were identified to attain high yields and high Ni concentration in the biomass. In tropical regions, other species are available such as Phyllanthus which accumulate over 1% Ni in dry shoots. These species are perennial so they regrow after annual cutting to harvest biomass. Expiration of our patents on the technology opens the opportunity for other organizations which control Ni rich natural soils or contaminated soils requiring remediation to commercialize the technologies. Inexpensive methods to remediate/revitalize Ni contaminated phytotoxic soils using agronomic approaches have also been developed and demonstrated at Port Colborne, Ontario, but adoption is delayed until formal agreements with government are completed. These new simple remediation and profitable phytomining technologies can obtain Ni from soils which contain Ni well below levels considered economic for current mining technologies, and the plants biopurify the Ni so it is easy to recover Ni metal from plant ash by pyrometallurgical or hydrometallurgical technologies. Although increasing pH decreases the solubility of Ni in all soils, raising pH increases Ni accumulation by Alyssum species. Hence usual chemical extraction methods for phytoavailable soil metals such as the DTPA- or NH4-OAc-extraction cannot predict Ni accumulation by Alyssum species.

Jan 1, 2016

By Nicolas Gatelier, Sophie Laurent, Thierry You

Hard-rock caverns for hydrocarbon storage are a very particular type of underground facility controlled not only by local administrative and regulatory constraints that can be very specific, but also by the possible risks of geotechnical or geomechanical failure. Each such facility throughout the world is a prototype that needs to be adapted to very different site conditions. The straight forward application of design methodologies from relatively similar fields (mines, tunnels) can be very useful, but risks holding back the scientific and technical improvements needed by an engineering industry in full development. Here we look at various case histories and at problems that have been raised where recent attempts at standardization would appear to have been ill adapted, and where storage designers, through experience and judgment, may still provide innovative engineering solutions.

Jan 1, 2015

By M. Loan

The Zinifex's Hobart Smelter uses the paragoethite process to remove dissolved Fe(III) from concentrated zinc leach liquors. This produces a residue consisting primarily of 6-line ferrihydrite (a hydrated Fe(III) oxyhydroxide), several insoluble components derived from the calcined zinc concentrate neutralization agent and other precipitated phases, such as jarosite and silica. The precipitation of 6-line ferrihydrite in the paragoethite process was studied using a laboratory-scale continuous crystallizer, and the conditions were selected to limit high levels of dissolved silica and jarosite. This approach allowed the reactor pH and the rate of precipitation to be correlated with residue solid-liquid separation, particle size, morphology, residual zinc and sulfate concentrations, and phase formation (e.g., goethite, jarosite, schwertmannite, and 2- and 6-line ferrihydrite). These studies delineated the mechanism of 6-line ferrihydrite precipitation in the kinetically controlled paragoethite process, and its inter-relationship with goethite and jarosite precipitation under conditions where 6-line ferrihydrite is favoured. Unexpectedly, the generation of a more crystalline goethite precipitate with larger "primary" particle size did not produce a residue of improved properties, as bulk aggregates dictate the physical properties of the residue and not the crystallinity. Furthermore, it is difficult to precipitate 2-line ferrihydrite or schwertmannite under existing paragoethite process conditions.

Jan 1, 2006

By O. Bouaziz, O. Magnea, P. Cugy, E. F. Rauch

The experimental difficulty to perform Equal Channel Angular Extrusion (ECAE) of a bulk sample of hard material such as steel was overcome. The original method proposed in this paper consists in replacing the bulk sample by a stack of alternated hard metal (steel) and soft metal (aluminium) sheets. By applying this procedure to an Interstitial Free steel (IF steel), 2.7µm grain sized material was obtained after recrystallisation. Its mechanical properties (hardness, formability in shear, hardenability and faigue limit) were investigated and compared with the properties of the same IF steel with conventional grain sizes (12m and 25µm).

Jan 1, 2004

By W. Evans, T. Steis

"Sulphide ores under certain circumstances will react with explosives to generate an autocatalytic chemical reaction. This reaction is exothermic and results in the production of large volumes of poisonous gases and creates an unsafe, unstable condition with the possibility of a low energy deflagration or even a detonation of the loaded hole. This paper outlines the conditions that need to exist for such a reaction to take place and the precautions necessary to minimize or eliminate the problem in areas of reactive ore. A special case study involving a northern Ontario mine will be detailed.IntroductionOne of North America's leading underground gold producer's processes over 6500 tonnes of ore per day from an orebody containing high concentrations of sulphides. After six years of problem free operation, the mine experienced two serious reactions in two months between the sulphides and AMEX II, the ammonium nitrate and fuel oil explosive it uses."

Jan 1, 1995

By W. J. Mcgaughey, R. G. McCreary, S. C. Maxwell, R. P. Young

"Seismic tomography is a process for obtaining images or maps of seismic velocity or other seismic properties of a rock mass. Seismic velocity images reveal variation in elastic moduli which, in tum, are related to several properties required in the geological or geomechanical assessment of a rock mass. Seismic velocity is sensitive to lithology, discontinuities, and in situ stress. Spatial or temporal variation of these properties may be indirectly assessed. Tomographic measurements are sensitive to volumes of ground, rather than determinations at points, or along lines or surfaces, as in conventional geological or geomechanical measurements or mappings.Tomography surveys are complementary to conventional measurements as they have the capability to interrogate a substantially larger volume of ground. They are thus useful in discerning trends or patterns in regions between or surrounding conventional ""point"" measurements of lithology, rock quality, stress, or other parameters of interest. Seismic velocity images give broad indications of trends in velocity; their spatial resolution of ground properties is typically on the order of five to ten per cent of the nominal survey dimension.Research in seismic tomography has been carried out for several years, and the capabilities and limitations of the technique in mining environments are beginning to be understood. This report reviews the present capabilities of seismic tomography surveys in mining, emphasizing rock mechanics applications. Six case studies are used as examples to demonstrate the capabilities of the method in assessing lithological variation, density and orientation of discontinuities, and the effects of stress."

Jan 1, 1994

Presentation Plan Hoist ropes ?Importance ?Mandatory and routine Inspections Continuous monitoring of wire ropes for mine hoisting ?Why a continuous monitoring of mine hoisting ropes.? ?Description of the ??Contiscan?? monitoring system ?Information data gathering Advantages of the ??Contiscan?? monitoring system ?Visual rope inspection on daily basis ?Monthly inspection ?Payload capacity flexibility and potential increase for deep mining operations. ?Periodical inspections by external experts ?Importance of the costs associated with hoisting production shutdowns. Commercialization and availability

Aug 1, 2013

By N. Katsikaros, R. Agius, B. Adaszynski

"With stricter limits globally being imposed on cyanide discharge levels in plant tailings, having a reliable and well designed cyanide detoxification circuit is critical for any operation. The INCO SO2/Air method is most commonly used for cyanide detoxification where sulfur dioxide and oxygen combine to oxidize cyanide to the much less toxic cyanate. This paper discusses the steps involved with the development, from laboratory through to design, of a robust cyanide detoxification circuit. The goal is to produce a cyanide detox circuit that reliably meets discharge target with the lowest operating and capital cost.Design begins in the laboratory where continuous tests simulate full scale operation of a detoxification circuit. Detailed design relies on several design parameters, based on theory and experience, to ensure the reactor can satisfy requirements of the cyanide destruction reaction. Selection of the correct reagents and their supply to the reactor is important to an operable process with minimal operator workload. The operability of the system relies on correct process control strategies to maintain optimal reagent addition and chemical conditions in the reactor. These design factors are critical to providing a robust plant that will consistently meet cyanide discharge levels, ensuring uninterrupted production and plant profitability."

Jan 1, 2014

By Sandra L. Mesa-Espitia, Gretchen T. Lapidus

Gold present in arsenopyrite matrices is refractory and requires highly oxidative pretreatments in order to obtain acceptable degrees of extraction. However, these release many byproducts that are harmful to the environment. In the present work, a high-grade arsenopyritic ore was pretreated with different solutions, containing hydroxide ion, EDTA, oxalic, tartaric, or citric acids, to improve gold extractions in a posterior leaching step. The pretreatments were carried out at room temperature for 24 hours with a respective ligand concentration of 0.25 M. Once completed, the residue was leached in a thiosulfate solution to quantify the effect of the pretreatment on gold extraction. Only 29% of the gold content was leached, with very slow kinetics, in the untreated mineral. However, after pretreatment with tartaric or citric acid, the kinetics improved, although the percentage of gold extraction only reached 42-45%. The highest gold recovery, with very rapid kinetics, was found with the oxalic acid or the hydroxyl ion pretreatment (70 and 62%), respectively, but also corresponded to the most arsenic co-dissolution.

Jan 1, 2014

By Ali Roshanfekr

Linear mine-waste dumps at open-pit mine sites essentially represent expedient places to deposit large quantities of waste rock. Being in valleys in most cases, the effect of the water flowing through and out of the deposit often raises questions about their hydraulic behaviour and geotechnical stability, especially the zone of the downstream toe. In order to provide better tools to assess the behaviour of these dumps a laboratory and analytical study was conducted. Firstly, physical models were built to assess the flow capacity and hydraulics associated with the linear growth of such dumps. It was found that the elevation of the point of first-emergence on the downstream side becomes constant after the dump grows to a certain length, but that the upstream depth concurrently increases. The limits of applicability of the theories of Hansen et al. (1995, 2005) are discussed in this regard. Secondly, in analysing the seepageface downstream, two approaches for solving this spatially varied flow (SVF) problem were undertaken. Under one of the approaches links to SVF depths were merely made to the hydraulic heads of the body (interior) and flux was calculated using conventional surficial nodes after the fact, Under the other approach flux nodes were used to link the SVF algorithm to the hydraulic heads further ?inside? the body of the rockfill. Although there are inherent uncertainties, it was found that these two methods can be made to perform equally well. Research continues but it appears that a linear variation in depth can be assumed without inducing any unrealistic exit gradients in the zone of primary concern with respect to unravelling.

May 1, 2011

By A. Singh

Deformation structures after tensile and compression tests on Mg926Zn64Y alloy extruded at 250°C and 400°C are studied, in as-extruded and heat treated conditions. The icosahedral phase particles stimulate recrystallization during extrusion, resulting in fine grain size. Tensile and compression tests at room temperature show comparable yield strength, with a yield asymmetry ratio up to 0.98. c-type dislocations are observed in the grains near the submicron size icosahedral phase particles. The source of these dislocations is believed to be dissociation of <c+a> type non-basal dislocations. No dislocation pile-ups on icosahedral phase particles are found. {10 1 2} type twinning occurs in compression.

Jan 1, 2006

By Denilson Coutinho, Euler Soares, Paulo de Tarso, Jordana Ferreira, John R. Goode, Andreas Sprecher, Alexandre Rocha

The Serra Verde Project is located in the northern part of Goiás state, Brazil, and comprises 49 mineral claims covering an area of 69,814 ha. The Serra Verde deposit is a rare earth element (REE) enriched weathered granite comparable to the weathered granite, or ionic-clay, deposits found in southeastern China. The Mineral Reserves of the Serra Verde Project total 388 Mt (Measured and Indicated) at an average grade of 1,484 ppm of REE oxide (REO). Several hundred agitated leach and column leach tests have confirmed recovery of about 40 to 55% of the REE, except for Ce, using simple desorption techniques. Present plans call for a heap leach operation followed by precipitation of impurities and precipitation of a pure REE carbonate suitable for refining and separation. The project plan includes initial production of 5,000 t/a of REO, with a high content of heavy and critical REO, rising to 10,000 t/a of REO. This production rate will be obtained by mining of the Mineral Reserves over a 22-year mine life at an initial rate of 6 Mt/a for the first four years with the mining rate thereafter increasing as required by grade and production targets.

Jan 1, 2014

By M. H. Kotze, V. Yahorava

A gold-selective ion exchange resin, containing tributylamine groups, was developed by Mintek for the recovery of gold from cyanide leach solutions. The Dow Chemical Company and, more recently, Purolite commercialized the production of this gold selective resin for use in the gold mining industry, and it is marketed as Dow XZ-91419.00 and Purolite A194 respectively. A novel application of this resin is the selective recovery and separation of AuCl4 - f rom p latinum group metals (PGMs) in chloride and nitrate solutions. The current paper describes potential benefits of this type of resin for selective recovery and upgrading of gold from low grade chloride or nitrate waste streams, and the possibility of gold separation from PGMs during their refining in chloride media.

Jan 1, 2014