Search Documents

By R. Sharma, I. Miskovic, S. Miskovic

Solvent extraction (SX) is a widely used method for the extraction of copper from pregnant leach solutions or other ionic solutions in hydrometallurgical applications. About 17% of total refined copper production worldwide is produced using SX followed by electrowinning (EW). Conventional SX units, such as mixer-settlers, consume a large amount of extractant, offer poor process control and yield low extraction efficiency. Extraction efficiency is poor due to low specific interface area, crud formation, emulsification, and slow phase separation stage. Micro solvent extraction (micro-SX) is a rapidly developing technology that provides an opportunity for improved process control, higher extraction efficiency, lower residence time and, as such, has a potential to reduce the environmental footprint of SX operation. In this research, extraction of copper ions in an acetate buffer media is investigated using D2EHPA with kerosene as a diluent. Chemical factors such as extractant concentration and ionic concentration of aqueous phase are varied to determine the optimum conditions. Subsequently, the extraction efficiency and reaction time of new micro-SX reactors are compared against previous bulk SX studies. Extraction in the microfluidic reactor was observed to be faster with a residence time more than an order of magnitude lesser than bulk SX. This study forms a prelude for developing new modular micro-SX units which will enable continuous, effective, and safe operation on a large scale. In future studies, numerical and analytical models validated through this work will help eliminate rigorous experimentation and enable faster design and fabrication of micro-SX units. INTRODUCTION Conventional industrial solvent extraction (SX) units such as mixer-settlers, extraction columns present various disadvantages. Low specific interfacial area, crud formation, and emulsification in industrial reactors lead to long extraction times and severely hamper extraction efficiency (Priest et al., 2011; Chen et al., 2017). Microfluidic extraction considerably improves upon the current extraction practices by (1) creating a large surface to volume ratio that enables rapid mass transfer across the interface, (2) better process control, and (3) easier separation of phases (Kashid, Renken, & Kiwi-Minsker, 2011; Ciceri, Perera, & Stevens, 2014). These factors establish micro-SX as a crucial mode for process intensification. Although, a micro SX unit has significantly low processing volume than conventional extraction methods, their throughput can be increased via massive parallelisation (‘numbering up’), which is an area of active research (Darekar, Singh, Mukhopadhyay, & Shenoy, 2016a; Kriel, Woollam, Gordon, Grant, & Priest, 2016).

Jan 1, 2019

By A. P. E. Dirige

In order to maximize the recovery of ore in variably dipping ore zones of moderate width, cemented backfill is normally placed to serve as structural support. With the intention of saving on costs, backfill of low cement content can be used, which are often supported by a sillmat of higher strength. The stability of the low cement backfill face, exposed during adjacent mining, must be carefully studied to provide very effective, safe and economic mining operations. Improper design of these stope support structures may result in fill mass failure resulting in relaxation and failure of the stope walls, with consequent losses of production, ore dilution, and in safety problems. This paper presents a study conducted to assess fill performance during adjacent pillar mining and to provide a comprehensive understanding of backfill behaviour, the failure modes that may occur and the consequences to production, ore dilution and to safety problems, and accurately predict their stability. The design study investigated the effects of stope width and height, orebody geometry and inclination, and wall roughness on the stability of cemented backfill during adjacent pillar mining. Fill properties used were based on paste fill specimens cured for 28 days. Paste fill performances were assessed based on analytical and numerical modeling studies for the different mining conditions. Analytical modeling was carried out using limiting equilibrium analysis and numerical modeling was carried out using FLAC3D. The modeling results suggested that, for stopes that are inclined with smooth wall rock conditions, backfill failure, driven by the fill self-weight, has minimum dependency on the binder content and is reduced by resisting forces developed on the footwall-fill contact. For inclined stopes with rough wall rock conditions, wall roughness contributes significantly to the stability of the backfill during adjacent pillar mining. The analytical modeling approach was demonstrated to be useful in providing some approximate parameters for predicting the behaviour of paste fill exposed faces during adjacent mining, but cannot predict the mode or mechanisms of failure. Numerical modeling not only assess the stability behaviour of paste fill free faces, but also is able to provide a better idea of paste fill failure modes and possible failure mechanisms. The depth of failure and the potential for instability for a simulated stope filled with paste fill can be predicted, and may be useful in estimating the mass of material that could possibly fail and ore dilution levels.

May 1, 2009

By Ross Gilders, Leo Cheung, C. David Desjardins

"For the past twenty years significant progress has been made in bacterial leaching. In fact, a recent article in the Northern Miner has cited that nearly all new copper production is based on bioleaching. The bacteria that play the predominant role in bioleaching is an obligate chemolithoautotroph called thiobacillus ferrooxidans. These bacteria thrive in areas rich in sulphide and prefer low acid media. In the simplest sense, they metabolize sulphide converting it to sulphate either as acid or as soluble metal sulphates. This process is well known because these bacteria generate acid mine water. Over the last five( 5) years, we have been carrying out development work on creating optimum bioleach conditions for the extraction of metals from sulphide rich ores and concentrates. Recently, a study was carried out on a byproduct sulphide concentrate produced in a tin flowsheet developed for the Mt. Pleasant Mine of ADEX Mining Corp. The objective was to determine whether a bioleach process might successfully leach this sulphide material which contains copper, zinc, iron and, what is more important, trace metals such as Indium, Gallium, and Bismuth. The current work describes the successful recovery of these metals achieving extractions of more than 80% by applying bioleaching techniques. An overview of this technical program forms the basis of this paper.IntroductionBio-Oxidation of metal sulphides has emerged to be one of the leading edge hydrometallurgical processes for the economic extraction of metals from ore and concentrates. The fundamental process involves the bacterial assisted oxidation of sulphide to sulphate yielding metal sulphates which can be subsequently leached by conventional means. The bacteria that play the predominate role is an obligate chemolithoautotroph named thiobacillus ferrooxidans (TF). These bacteria thrive in areas rich in sulphide and occur naturally worldwide. In fact, TF is responsible for generating acid in water (acid mine water) from exposed sulphide surfaces primarily through the oxidation of pyrite. TF bacteria thrive under the proper conditions of temperature and oxygen supply in the presence of sulphides and populations in excess of a million per millilitre (ml) of solution are achievable. Typically, at room temperature, the bacteria will bio-oxidize in a pH range of 1.0 to 3.0. Today, bio-oxidation has been applied commercially with great success for the extraction of uranium, copper, and gold."

Jan 1, 1996

By W. P. Corking

"The purpose of this paper is to describe the relationship of the goldbearing ore to structure at the Pickle Crow mfoe. Information beyond this scope may be found in the reports and papers of Hurst( l), Bothwell(2), Thomson(3) , and Monette( 4).The property lies on Crow river, in Patricia district, 80 miles northeast of Allanwater, and about 125 miles northeast of Sioux Lookout on the Canadian National railway. From April of 1935, when the mill began operation, to the end of 1944, a total of 564,890 oz. gold and 49,275 oz. silver were recovered from 958,416 tons of ore.Mining on the property is at present carried on in two separate orebodies, the Howell and the No. 2 vein. Stoping has been carried on from every level on the Howell vein to a depth ot 2,450 feet below the surface and from several levels on the No. 2 vein through a mile long cross-cut on the 750-foot level to the Howell vein workings. A steadily increasing volume of ore is being obtained from the No. 2 vein.Each of the two orebodies consists of vein quartz with small amounts of other gangue minerals either in a single vein or a stockwork of veins. Both lie within sheared walls and carry gold in the free state. Fig. 1 shows the position of the veins with respect to the surrounding rocks. It will be noted that the delineation of the beds of iron formation shows that the lava flows and minor, interbedded sediments that make up most of the country rocks are areally folded and contorted.STRUCTURENearly all gold found to date in sufficient quantity and concentration to make ore in the Pickle Crow area is confined to these major quartz veins . Both strike a little north of east and dip north, and in both cases the attitude of the enclosing rocks is somewhat more north of east in strike and more steeply north in dip than that of the veins. As a result of this disposition both veins migrate across their enclosing rocks at a moderate angle in both dip and strike. (In this connection it should be noted that No. 2 vein dips at a considerably flatter angle than its host rock, but has a very pronounced rake to the northeast, effecting the same result as in the Howell vein.)"

Jan 1, 1954

By M. A. Roche

The property of the Hudson Bay Mining & Smelting Company, Limited is located at Flin Flon lake, 85 miles northwest of The Pas, Manitoba, on the Manitoba-Saskatchewan boundary. The area is at latitude North 54°, and is approximately 1,000 feet above sea level. The ore-body occurs in amygdaloidal greenstones, which are to be referred to the earliest basic volcanic flows in the district. It was discovered in an outcrop on a point of land jutting into Flin Flon lake, and subsequent diamond drilling proved that it extends under the lake both to the north and south of the point of discovery. After the taking of soundings from the ice during the winter months, it was estimated that l,000,000 tons of overburden, mainly mud and clay, would have to be removed to expose the underlying ore. Flat diamond-drill holes indicated that the ore-body was separated into more or less independent lenses by horses of unmineralized greenstone, and that in places the overall width, including horses of waste, reached 450 feet. These several] conditions were the main factors influencing the management in their decision to adopt an open-cut method for the mining of the upper portion of the ore-body. Before it was possible to commence stripping operations, it was necessary to dam-off the eastern portion of Flin Flon lake, instal pumps, and de-water the dammed-off area. Dams for this purpose were constructed of mine waste rock and clay filler from nearby hillsides. Material for the bottoms of the dams was taken across Flin Flon lake in hopper-bottom barges. Trestles were then built on the dam bottoms and dams were complete by the time trackage was available. De-watering commenced in April, 1930, and was completed by the latter part of May of the same year. Estimated pump output for the period was roughly four billion gallons. Two Morris 10-inch dredging pumps were used, direct-connected to 250 h.p. electric motors. Individual pump capacity was rated at 3,000 g.p.m. against a 150-foot head. Average head for the operation was 50 feet, which increased the total output considerably. The pumps were mounted on floating barges in cribbings of piling driven at the lowest points in the lake bottom.

Jan 1, 1933

By A. M. Bell

"The property of Gaspe Copper Mines, Limited, is in the Gaspe Peninsula some 60 miles west of the town of Gaspe and 20 miles in from the north coast. The Copper Mountain deposit was first discovered in 1921 and first optioned and drilled by Noranda in 1938. The Upper Needle Mountain showings a mile south were found in 1938, but it was not until after a delay of 10 years that the more important deep ore at Needle Mountain was located by drilling. Production started in 1955, and the smelter commenced operation in December. Mining is by open stope methods with first production coming from the Lower Needle Mountain orebody, of which only a small portion has been exposed in underground openings.Stratigraphy and AlterationThe country rock is composed of limy siltstones of Devonian age. Away from alteration these are dark and generally carbonaceous. Throughout the drilled area numerous narrow layers of tuffaceous fragmental material occur, and such beds are found to provide excellent horizon markers by virtue of their uniform thickness and wide lateral distribution. These markers are valuable for stope control in mining the bedded replacement deposits.Intruding the sediments at Copper Mountain are porphyry dykes, and one drill hole encountered granite 1,400 feet below the valley. Solutions responsible for the rock alteration and ore deposits seem to have emanated from this intrusive centre.On the mine claims strong hydrothermal alteration has completely obscured the original character of the sediments. The unaltered formations are all very similar in appearance, but following alteration rocks that are very dissimilar in physical characteristics are produced, and such differences have an important influence on ore deposition. The alteration effects are known to extend over a vertical range in excess of 3,000 feet and have a surface area of two square miles. All known ore bodies are within the zone of alteration. In this, rocks are strikingly bleached to a white colour in contrast to the normal dark-coloured sediments, and are much harder and more abrasive, with bedding often obscured. The first effect of alteration is driving off of carbonaceous matter, followed progressively by silicification in the acid rocks and by the formation of lime silicates in the lime rocks, with an accompanying gain in silica and a corresponding loss in lime. Extensive analysis has shown that there is an actual addition of silica involved in the alteration."

Jan 1, 1949

By Scott D. Long

"Abstract-Grass roots exploration has an emphasis on good precision at low (sub-economic) concentrations of an element, in order to identify "anomalies" which may lead to drilling targets. Although it is wise to have well-defined quality controls in place during early stage sampling, the control procedures at this stage tend to be rudimentary. When a deposit warrants detailed delineation, the need for accurate geological characterization and assaying of ore-grade rock must be supported by appropriate quality control procedures.As a project returns more promising results, and the likelihood of the project warranting a prefeasibility study increases, it is time to tighten quality assurance requirements and quality control protocols. Delays in instituting adequate quality control and verification procedures may lead to costly remedial actions that can also delay completion of the prefeasibility or feasibility study. Sometimes, as a project matures, the quality control and quality assurance aspects fail to keep pace with the changing nature of the work: an increasing emphasis on precise and accurate assaying of oregrade rock.A resource model is like a house of cards. The foundation of the house is the geological observations, the sampling methods and the geological interpretations performed upon those samples. Upon the sampling, which includes all the sub-sampling steps of sample preparation, rest the assay results. The quality of the assays can be no better than the quality of the sampling. Good assaying technique will preserve all biases and imprecisions introduced during sampling and sample preparation; it cannot remove them. If the sub-samples and/or assays are bad and must be redone, all the succeeding levels of the house of cards must also be rebuilt, or at least patched up.From geological observations, a geological interpretation is built, the quality of which is critical to the construction of an acceptable resource model. Geological elements are difficult to assess, and are not discussed here; they are dependent upon the expertise of the geologists involved. Geological knowledge contributes essential quality control elements to resource/reserve determinations (Sinclair and Postolski, 1999; Postolski and Sinclair, 1999).This paper consists of five sections: (1) overview of quality control protocols, (2) maintaining quality control of databases, (3) quality control of drill sampling, (4) optimizing crushing and grinding requirements, and (5) quality control of assay data acquisition."

Jan 1, 1998

By G. Guiglionda, A. Deschamps, F. De Geuser, M. Langille, B. J. Diak

"Increased demand for light-weighting in passenger vehicles has created a need for strong, light, ductile materials to be used in body-in-white applications. The AA6xxx-series of aluminum alloys are suitable candidates meeting most requirements but can fall short of the formability demands of designers, necessitating an understanding of what controls the formability in this alloy series. This work examines the effect of copper alloying in AA6xxx on the pre-ageing and natural ageing responses of the microstructure and mechanical properties. The changes in microstructure observed by differential scanning calorimetry and hardness testing are related to the work-hardening and strain-rate sensitivity parameters for these alloys measured by tensile testing. An observed asymmetry in the measured strain-rate sensitivity associated with increasing versus decreasing strain rate changes suggests that a different mechanism operates for the two conditions. It is postulated how this asymmetry in strain-rate sensitivity will impact the necking and ductility behaviour of these alloys.INTRODUCTION The widespread use of AA6xxx series alloys in the form of sheets has provided the need for a more thorough understanding of the complex interactions between composition, processing, resulting microstructure and ultimately, the mechanical properties of the alloys. Conventional industrial practices involve the production of rolled AA6xxx sheet (typically 1 mm thick) to be used for body-in-white (BIW) applications for auto body panels (Hirsch, 2004, 2014). The final metallurgical step prior to the shipment of these panels to manufacturers involves a solution heat treatment (SHT) reverting the ageing products of the alloys into solid solution and the product is then shipped to the customer. During this shipping time and while sheets are waiting to be used, the natural ageing (NA) process occurs whereby the strength of the alloys increases resulting in reduced formability. This can result in a product that is unable to meet the formability demands of the automotive manufacturer. As a result, industry has moved towards performing pre-ageing (PA) treatments to prolong the “shelf-life” of the material prior to it having insufficient formability. Once formed into BIW panels, the parts are then painted and subsequently undergo the paint curing heat treatment which consists of a short period of time at medium temperature, typically 20 minutes at 170–190°C. This short artificial ageing (AA) treatment, known as the paint bake (PB), provides additional strength and improved dent resistance for the material, but reduced formability. The PB result is strongly dependent on the PA treatment performed prior to the forming operation. Furthermore, the addition of copper (Cu) to a base Al-Mg-Si composition is known to increase the alloy’s strength. The goal of this work is to study the effect of Cu on strength, strain hardening, and strain-rate sensitivity (SRS) of these alloys, to understand the strength-formability compromise, for two separate heat treatment schedules; one including and one excluding the PA treatment, both followed by NA."

Jan 1, 2018

By A. Osouli, B. Moradi Bajestani

"Increase in permeability of rock mass is vital for both petroleum and geothermal applications. Hydraulic fracturing is a common method to create and increase the permeability for production. Due to the complexity of fracture propagation in a naturally fractured medium, understanding the interaction between hydraulic fracture (HF) and natural fracture (NF) is of great importance to optimize the fracturing process. The possibility of interaction between HF and NF is partly a function of orientation. Various scenarios are predictable for hydraulic fracture regarding the intersection with NF such as being arrested by NF, crossing NF or crossing the fissure while injecting water into it. Different parameters such as geomechanical and geometrical properties of surrounding rock mass, the operational parameters such as injection rate and the angle between created hydraulic fracture and natural fracture (approach angle) can affect the result of hydraulic fracture and natural fracture intersection. In this paper, using a series of flow-coupled Distinct Fracture Network (DFN) simulations, hydraulic fractures were analyzed to investigate the influence of the aforementioned parameters on the hydraulic fracture propagating. Results show that the most significant parameters affecting the interaction of natural and hydraulic fracture are orientation of the intersection as well as injection rate. The interaction and fracture propagation in NF and HF intersections are also studied and discussed in detail.INTRODUCTIONThe hydraulic fracture technology has substantially changed the oil, gas and geothermal industries. With the help of this technology, extraction of fossil resources from tight shale reservoirs will be economical, feasible and sustainable. Due to presence of massive oil and gas trapped in these reservoirs, this technology has been the center of attention for the past 40 years (King, 2012). Hydraulic fracturing is the process in which high pressure water is pumped into shale unconventional reservoirs with low to ultralow permeabilities. With this process paths are created in these mediums for delivering oil and gas to horizontal wellbore and increase the surrounding rock medium permeability. Economical and sustainable stimulation of these tight reservoirs is highly dependable on our understanding in regard to fracture propagation in the highly complex rock medium. Hydraulic fracturing process in rock mediums with preexisting natural fractures is more complex because of the high possibility of Hydraulic Fracture (HF) being arrested or deviated by Natural Fracture (NF). Also, HF and NF intersection can influence the required pumping pressure, injection rate, the outcome of horizontal wellbore and the affected geological underground zones. Since the 1950s, numerous studies have been conducted to predict and plan fracture propagation with the help of modeling and simulation methods. Having a thorough and accurate prediction of fracturing process will not only prevent stimulation of unwanted geological zones or pollution of aquifers, but also will improve the efficiency of the fracturing process. Previously, several studies have been conducted in order to investigate and analyze the interaction of hydraulic fracture and natural fracture (Cottrell, Hosseinpour, & Dershowitz, 2013; Doe, Lacazette, Dershowitz, & Knitter, 2013; Shakib, 2013; Zhang & Jeffrey, 2006)."

Jan 1, 2015

"During the development of a mining project, samples are taken for metallurgical tests. The sample can be a composite sample made of material from a selection of various drilling products or a sample from a mining test. It can be also a sample from an existing plant in order to investigate process enhancement. This sample can represent several tonnes of material which are analysed and split for use in various tests.In the current case, a composite sample of gold ore is dedicated to a Gravity Recoverable Gold (GRG) test. The properties of interest are the head grade of gold, the size distribution of the material, and the gold assay per size class. The sample is mixed and a sub-sample is taken to measure the feed properties: the size distribution and the gold assay per size class. The remaining material of the sample is subject to the first stage of concentration using the laboratory Knelson concentrator. The concentrate is analysed in its entirety, while a sample of tailings is taken for the same analysis. The remaining part of tailings is subject to grinding to feed the second and third stages of concentration. Similar sampling is performed at each stage.The concentration performances are analysed in light of these measurements. But what is the accuracy of the measurements of the properties? Pierre Gy’s theory of sampling, associated with a heterogeneity model built using the GRG test results, will answer this question. The current paper presents, through a real example, the calculation of the errors of the measurements of size distributions and gold assays performed during the GRG test. The uncertainties of the concentration performances and liberation size estimate are then calculated and their impact on the results interpretation is analysed.INTRODUCTIONDuring the development of a mining project, samples are taken for metallurgical tests. The sample can be a composite sample made of material from a selection of various drilling products or a sample from a mining test. It can be also a sample from an existing plant in order to investigate process enhancement. This sample can represent several tonnes of material which are analysed and split for use in various tests. In order to take into account the ore variability in terms of gold deportment, it is recommended to perform variability studies (Dominy, Murphy, & Gray, 2011, Dominy, 2013) using samples representing various horizons or years of production. But for a given ore type, it can be necessary to perform many tests with different operating conditions (Brochot, 2012a). In that case, the variability of the samples is not due to the heterogeneity of distribution of the deposit, but only on the heterogeneity of constitution of the primary sample. The level of confidence associated with the estimated performance parameters is directly linked to the overall error (including sampling error) of the measurements performed during the tests."

Jan 1, 2016

By Grant Arnold

Le Camp Minier de Matagami est situé dans la ceinture volcano-sédimentaire Harricana- Turgeon appartenant à la Province du Supérieur, sous-province de l?Abitibi, au Québec. Les gisements de métaux de base polymétalliques sont retrouvés exclusivement dans les deux domaines lithotectoniques comprenant l?association basalte-rhyolite (Matagami-Brouillan et Joutel-Raymond). Tous ces dépôts, à l?exception de ceux de Selbaie, sont de type exhalatif et représentent des dépôts volcanogènes à Zn-Cu, typiques de l?Archéen. Le complexe volcanique de Matagami est constitué principalement de deux phases de volcanisme tholéïtique. Les dacites et les rhyolites du Groupe de Watson, représentent la phase la plus précoce et celles-cis sont recouvertes par la seconde phase qui est constituée majoritairement de roches intermédiares à mafiques intercalées d?horizons felsiques, formant le Groupe de Wabassee. Un sédiment chimique sulfuré, la Tuffite Clef, marque le contact et l?hiatus entre ces deux groupes. Cette tuffite est reconnue à la grandeur du flanc sud du camp minier et représente l?horizon favorable à explorer puisque sa déposition a correwspond à une période d?intense activité hydrothermale. Le complexe volcanique de Matagami est limité au nord et au sud par des bandes sédimentaires orientées est-ouest, connues respectivement sous les noms de Groupe de Matagami et Groupe de Taïbi. Le Complexe intrusif de la Rivière Bell, qui occupe la base du Groupe de Watson, est un complexe lité consistant en une séquence stratifiée gabbroïque avec localement des niveaux stratiformes à concentrations d?oxydes magmatiques, la bordure de ce complexe est marquée par la présence d?un horizon granophyrique. Cette intrusion synvolcanique prétectonique, représente probablement la source de chaleur étant à l?origine de l?activité hydrothermale observée dans les roches volcaniques sus-jacentes. Suite à un levé aéroporté, le camp minier de Matagami a vu le jour en 1956 lors de la découverte du dépôt de Mattagami Lake, un gisement volcanogène de 25.6 millions de tonnes. Depuis ce temps, un total de neuf gisements ont été exploités et un dixième, Bell Allard, est présentement en production. En date du 31 décembre 1999, la production historique du camp s?élevait à plus de 41 millions de tonnes. Cette présentation mettra l?accent sur la géologie des récentes découvertes dans le prolifique camp minier de Matagami. Les ressources publiées pour le dépôt Persévérance sont de 947,000 tonnes titrant 19.12% Zn, 1.37% Cu, 32 g/t Ag et 0.40 g/t Au. Deux autres découvertes, Équinoxe et Persévérance Ouest contibueront à la ressource globale. Les trois dépôts sont situés au niveau de la Tuffite Clef même si les roches sus-jacentes ne sont pas celles typiquement observées dans les autres dépôts du flanc sud. Ces découvertes sont le résultat d?un programme d?exploration ciblé et soutenu, démontrant ainsi la possibilité de découvrir de nouvelles ressources même dans les camps miniers comme Matagami qui ont été explorés intensivement depuis plus d?un demi-siècle.

May 1, 2001

By Stéphane Chevrel

Non-energy raw materials are vital inputs for the EU?s economy and maintaining fair and undistorted access to these materials for EU industry and citizens is increasingly difficult. Within the EU, exploration and extraction have to face increased competition for different land uses and a highly regulated environment. While the EU is currently dependent on the importation of many metals, the overall potential for mining and quarrying in Europe is strong. In spite of this, the land area available for extraction in the EU is constantly decreasing, turning access to land into a key challenge for the extractive industry. The EOMINERS project aims at contributing to demonstrate how to improve the EU capacity in implementing new mining sites and their societal and environmental acceptability. The overall aim of EO-MINERS (Earth Observation for Monitoring and Observing Environmental and Societal Impacts of Mineral Resources Exploration and Exploitation) is to bring into play EO-based methods and tools to facilitate and improve interaction between the mineral extractive industry and the society in view of its sustainable development while improving its societal acceptability. EO offers a unique opportunity to collect necessary spatial parameters that play a key role for better assessments of mining-related environmental and societal impacts. It could enable the development of means to identify the site-specific environmental and societal footprints of mineral resource extraction and to determine their respective significance. This understanding of global and cumulative footprints along a causal chain is needed in order to target policy measures. In this way the expected reduction of environmental and societal footprints in the mining sector can be most effective for the environment and more cost-efficient for public authorities and commercial operators. The project first defined environmental, socio-economic, societal, and sustainable development indicators and criteria that can possibly be dealt with using EO techniques. After an analysis of policies related to the environmental and social footprint of mineral industries, project expertise and stakeholder interviews (national and on-site) as well as site investigations led to the establishment of a list of indicators to be monitored, either directly or indirectly, through accessible parameters. Development of EO-based monitoring tools is then carried out over three demonstration sites: the lignite open pit of Sokolov in Czech Republic, the Mpumalanga coalfield centred on the town of Emalahleni (previously Witbank) in South Africa, and the Makmal gold mine in Kyrgyzstan. From these developments, it is subsequently intended to contribute to the development of generic, standardised EO data integration schemes, in particular in view of characterising affected ecosystems, populations, and societies and prepare indisputable documents that will make the basis for a sound ?trialogue? between industry, governmental organisations, and stakeholders. This paper discusses results obtained after three years into the project, focusing on product development over the demonstration sites and their relevance to the observation and monitoring of environmental and societal footprints of the extractive industry.

Aug 1, 2013

By X. J. Guo, H. X. Li

The biological heap leaching at Zijin copper mine is currently the largest industrial application of biohydrometallurgy and one of the earliest mines to develop biological metallurgy technology in China. Since 2001, through demonstration plant and different expansion stages, it has been developed to produce 20,000 tons cathode copper annually. However the ore grade of heap leaching gradually decline year by year with copper grade average at around 0.23% now. The copper mineral is mainly the secondary copper sulfide, and symbiosis with higher content pyrite, the sulfur and iron contents is about 15 times as copper in the ore (S/Cu>15), so the acid and iron treatment of leachate, extractant and acid mine waste water is a great challenge. Combined with located in the rainy area of southern China, huge amounts of over 10 million cubic meters acid drainage need to be treated every year, so the recovery of copper from waste water as well as low grade ore is one of the characteristics of this process. This paper in general introduced the operation of heap leaching, solvent extraction, stripping and electrowinning process in Zijin mine, summarized the experience of production and technical practice, and discussed the methods of heap construction, leaching rate enhancement, third phase formation and treatment, mine effluent treatment, resource recovery and heap slope reclamation. INTRODUCTION The Zijinshan gold and copper mine is located in southeast China, Fujian province, and the typical distribution characteristics of gold and copper deposit are "upper gold and lower copper", both are large porphyry deposits. By the end of 2017, the accumulated proven reserves of available gold resources were 318 tons, copper are 2.15 million tons, and the prospective reserves of copper are more than 5 million tons. The gold mining is open pit while the copper mining is open pit and underground. The cut-off grade of gold mining is 0.15 g/t, and that of copper mining is 0.15%. A large number of very low-grade gold ores (grade <0.30 g/t) adopt a combined ore-dressing process of “partial crushing/ore washing/reprocessing/heap leaching (overlying)/ carbon slurry" independently developed, while flotation and bio-heap leaching are adopted for copper mine. Among them, copper ore with more than 0.25% copper content enters the flotation system to produce copper concentrate, while that of less than 0.25% copper content is processed by bio-heap leaching, solvent extraction and electrowinning. Zijin biological heap leaching plant is the first mine in China to achieve the scale of annual output of ten thousand tons of cathode copper since 2006. In 2008, the solvent extraction and electrowinning system were expanded, now with a daily processing capacity of 20,000 tons of ores, an annual output of 20,000 tons of cathode copper, the expanded plant is the largest biohydrometallurgy plant in China.

Jan 1, 2019

By F. Musuka, D. Jenkins, A. Keyes

BHP Olympic Dam operates a Direct-to-Blister copper flash smelting Furnace (DBF) and an Electric Slag Cleaning Furnace (ESCF). Tapping blister copper from these furnaces via tapholes is a routine task carried out by trained personnel. Blister tapping is a high-risk activity with personnel operating in close proximity to molten metal. BHP’s risk management framework has identified taphole integrity as key to managing the potential for loss of molten metal containment and molten metal – water steam explosion, both of which have the potential to cause multiple fatalities. As part of the focus on managing this risk, since 2017, a dedicated Taphole Development Team has been embedded in the operation to run an accelerated improvement program focused on safely and sustainably embedding an improved taphole design with greater integrity. The program of works includes selecting and testing of new materials as well as improving operating discipline by collaborating with tapping personnel to convert their knowledge into codified condition monitoring and operating strategies. Computational fluid dynamics (CFD) is being used to derive critical risk controls, and to develop live-alerts to infer excessive refractory insert wear. To date, improving DBF blister taphole mudgun clay has led to more consistent drilling depths and subsequently reduced oxygen lancing requirements, resulting in improvements in taphole insert service life. On the ESCF, insert performance testing and development of a new taphole condition monitoring strategy, is being used to increase taphole insert tonnages to more sustainable levels. Operations personnel have been closely involved in different phases of the change management, this has led to standardization of tapping practices for both furnaces, and improved ownership of the proposed changes. The paper discusses the maturity in taphole integrity risk management as a result of recent and ongoing developments. It then provides an overview of future taphole developments proposed at Olympic Dam. INTRODUCTION Tapping operations at Olympic Dam and learning from significant events The Direct-to-Blister furnace (DBF) at Olympic Dam was built with a conventional design blister taphole, which was designed for manual oxygen lancing and clay stopper bar plugging tapping operations (Campbell, 2005). Manual tapping is a high-risk activity, where personnel work in close proximity to molten metal, and molten metal personal protective clothing and equipment must be used. Opening tapholes by oxygen lancing is a skilled activity and unintentional damage to the taphole inserts can occur. Since 2008, a Mudgun and Drill unit has been developed and trialled and is now in use on the DBF blister tapholes, to remove personnel from the line of fire when opening and closing tapholes. This has the additional benefit of reducing lancing damage to taphole inserts. A new taphole design labelled the Modular Blister Taphole (MBTH) was developed at Olympic Dam for the Mudgun and Drill operation. The intent of the design was for mudgun clay to fill the entire tapping channel when plugging after a tap. The drill would then drill through this clay plug to open the taphole.

Jan 1, 2019

By John F. Kearney

Labrador Iron Mines (?LIM?) Schefferville Projects consist of 20 major DSO deposits lying along a 120 km strike length in both the provinces of Newfoundland and Labrador and in Quebec. The town of Schefferville, Quebec lies close to the middle of this 120 km strike. LIM?s various properties comprise twenty different iron ore deposits which were part of the original Iron Ore Company of Canada (?IOC?) direct shipping Schefferville operations conducted from 1954 to 1982 and formed part of the 250 million tons of historical reserves and resources previously identified by IOC. LIM intends to develop all these resources in five separate stages. The first four stages will see the various deposits treated in three beneficiation plants, to be built adjacent to several of the deposits that comprise the Central, South Central and North Central Zones. The final stage is not yet planned but will likely involve a fourth plant. A Feasibility Study has not been completed on any of these Projects. LIM plans the development and mining of the various deposits in separate Stages. It should be noted that only the James and Redmond deposits have been permitted. All other deposits require environmental assessment and permitting. Only the James and Redmond deposits have been subject to detailed mine design. The Houston deposit has had preliminary mine design carried out. All other deposits will require detailed mine design when further geological data is collected and compiled. Detailed metallurgical testwork has been carried out on blue ore from James, Houston, Redmond and Knob deposits and to a more limited extent on yellow and red ores from these deposits. Only limited review work has been carried out on the high-silica blue ores. All of this work will be needed to be complete to confirm the final process routes. Additionally some metallurgical work will be required to be conducted on each of the other deposits to characterize their metallurgical response and to confirm expected recovery levels. Detailed mine design and metallurgical testwork has been carried out on those deposits that will form the basis of production for the initial years but further exploration, testwork and design is required for all the remaining resources. The first plant at Silver Yards and mine construction at James are now complete and initial production is expected in the spring of 2011. Metallurgical testing of the first stage deposits has established that the ore can be successfully upgraded to marketable standards. Based on the current testwork, a program of plant enhancement on the Silver Yards plant is now planned with the objective to increase both the plant throughput and recovery. Production of direct shipping lump ore and sinter fines is forecast at around 1.5 million tonnes in 2011 and, based on current and historical resources, growing to approximately 5 million tonnes in 2015 and thereafter. Production from the first four stages is expected to continue at about this rate through to about 2028.

May 1, 2011

By L. V. Bell

"The gold deposits of the Caribou mine are representative of those of the Province of Nova Scotia as a whole. The ore shoots within the deposits, in common with those elsewhere within the Province, are associated usually with interruptions or irregularities in the broader and uniform fold structures. The structural factors localizing ore deposition as applied more specifically to the Caribou mine are demonstrated chiefly by the close relationship of the two principal ore shoots, known as the main orebody and the 'high-grade' vein, with a pitching drag fold developed in the southeast limb of the major northeast-southwest trending anticlinal fold or elongated dome that constitutes the primary structural feature of the Caribou gold district. It is of interest to note that the evidence indicates that this drag fold, in common with other folds subsidiary to the primary fold, formed as a result of movement similar in nature to that which caused the primary fold itself. Presumably, therefore, these folds are coincident in time.The property described here as the Caribou mine is an amalgamation of two adjacent properties formerly known as the Ross and the Nova Scotia Gold, but which since 1934 have been controlled and operated as a unit by The Consolidated Mining and Smelting Company of Canada, Limited. The Caribou mine is situated in the Caribou gold district about 45 miles to the northeast of the city of Halifax and about 6 miles to the north of the Moose River gold district.The history of mining at Caribou dates back to 1867. The first recorded gold production is for 1869. From 1869 to 1933 the gold produced from the mines of the Caribou district aggregated 47,249 oz. from 93,234 tons of ore treated. The grade of the ore on the basis of the gold actually recovered from the district would thus average 72 oz. gold a ton, which, as will be noted from the following, is precisely the grade of the ore treated from the Caribou mine during operations by The Consolidated Mining and Smelting Company. These operations commenced in September, 1934, and milling on a commercial basis was under way during 1938. Since that time production, apart from a short period in 1945 during which efforts were concentrated on development work, was continuous to early in 1947, when the mine closed down owing to exhaustion of the known orebodies. Gold produced from the Caribou mine by The Consolidated Mining and Smelting Company from September, 1934, to the close of 1946 aggregated 43,205 oz. from 90,754 tons of ore milled; the grade of ore treated averaged 0.50 oz. gold a ton. The indicated average grade of O.S oz. gold a ton for the ore of the Caribou district throughout its mining history ranks somewhat higher than the 0.37 oz. a ton average for the ore milled to date from the several gold districts throughout the Province as a whole according to the production statistics of the Provincial Department of Mines."

Jan 1, 1954

By H. R. Kempthorne

"The Property of Bevcon Mines Limited, including a recently acquired adjoining south group, occupies an area of 2,625 acres in northeast Louvicourt township, Abitibi county, Quebec. It is situated 17 miles east of Val d'Or at the junction of provincial highways 58 and 59.Gold was first discovered in the area in 1931 by the late S. B. Jowsey on the present property of Buffaddison Gold Mines adjoining to the west. However, it was not until the winter of 1944-45 that diamond drilling encountered encouraging results on the Bevcon claims. During the period 1946-1948 a shaft was sunk to 1,000 feet and considerable development undertaken from the 500-foot to the 1,000-foot levels. Between 1947 and 1950 approximately 24,000 tons of dump ore and 48,000 tons of ore by stoping were milled at Perron Gold Mines. The favourable results of these tests prompted the decision to construct a milling plant at Bevcon. The mill began operating in July 1952, and presently has a capacity of 800 tons per day. In 1953 the shaft was deepened to 1,600 feet and is currently (1955) being driven to 2,225 feet.Total production of gold to the end of 1954 has been 101,024 ounces from the milling of 697,427 tons of ore of an average grade of 0·163 ounces per ton.GeologyThe Bevcon orebodies occur in a granodiorite stock which has an east-west length of approximately 4 miles and a maximum width of 1 1/2 miles. The property covers the central portion of the stock and its contacts with the Keewatin volcanics. Approximately one-third of the northern contact and one-half of the southern contact are contained within the Bevcon claims. The granodiorite has been cut by acid (feldspar porphyry) and basic dykes trending east-west. A younger diabase dyke, 300 feet wide, strikes northeasterly across the property 1,000 feet east of the shaft.The main ore zone, striking east-west, lies between the more northerly porphyry dyke and the north granodiorite-greenstone contact. It has been extensively sheared, fractured, altered, and mineralized by gold-bearing solutions. It is approximately 2,000 feet Jong from the west boundary towards the diabase dyke. The shaft is centrally located and passes through the south contact of the ore zone at the 500-foot level. The zone increases in width and trends northerly with depth, due to the porphyry and greenstone contacts having average dips of 80 degrees and 70 degrees respectively to the north. Thus on the uppermost or 500-foot level the width is 150 to 200 feet, and at the present bottom level at 1,600 feet the width is 400 to 500 feet.Another gold-bearing zone has been indicated 200 to 400 feet south of the main ore zone by limited surface drilling."

Jan 1, 1949

By N. Bartie

Realising the circular economy (CE) is faced with some significant challenges. Process metallurgy and its infrastructure play key roles at the heart of making the CE work. Therefore, the enabling role of process metallurgy within the CE will be central to the discussion in this paper, touching among others on product and system design as well as the key metallurgical and other process fundamentals that need to be investigated and understood to make the CE a reality. The central role of materials and its processing will be discussed in an integrated circular cities perspective. A key focus will be a discussion on designing a resilient “Smart Materials Grid” using and innovating metallurgical process engineering tools, which will manage the flows through Sustainable Circular Cities. The discussion will be using copper as leitmotiv of the discussion i.e. from copper ore, to metal, to complex products, recycling, product design and simulation and its impact. INTRODUCTION The transformation of our economies from linear to circular models in which waste materials become resources is the focus of the Circular Economy (CE) paradigm. Its important intentions: to take control of the damage we have been doing to the planet to ensure its livability and the welfare of future generations. This can only be achieved through careful utilisation of human, natural and economic resources. The concept is derived from several others (Beaulieu et al., 2015), of which Cradle-to-Cradle, Extended Producer Responsibility (EPR), Industrial Ecology, and Life Cycle Thinking are just a few. Other relevant concepts include resource efficiency (RE), design-for-recycling (DfR), and various others discussed by Blomsma and Brennan (2017) and Homrich et al. (2018), as well as various R-hierarchies e.g. Reduce, Reuse, Recycle (3R). However, does society comprehend these concepts, the actors and actions that influence them and how they interact? Do we know the limits of CE? Does society understand the key role of Copper and other metals to rendering the CE operable? True life cycle and systems thinking, focussed on simulation-based, process and metallurgical design are required to answer these questions. Lieder and Rashid (2016) identify nine widely-varying fields that study the concept ranging from sustainability sciences and engineering to economics, business, law, and social sciences. Overlap between questions addressed highlights the need for interdisciplinary collaboration (Nanz et al., 2017) in the assessment of the current status, and further steps needed to transform to CE. This doesn’t apply just in academia, but also in industry where concrete implementation of CE needs to occur at multiple levels, thus necessitating cooperation between government, civil society and other stakeholders (Beaulieu et al., 2015).

Jan 1, 2019

By P. I. Laforest, M. S. Moats

"Antimony in smelted copper anodes has been shown to cause problems in electrorefining including brittleness of starter sheets. In order to improve deposit properties, a study was conducted examining the effect of anode chemistry on cathode ductility and electrolyte chemistry. Two industrial anodes with different molar ratios of As/(Sb+Bi) were used in laboratory electrorefining experiments with commercial electrolyte, and the addition of commercial glue and Avitone. The ductility of 21-hr copper deposits was evaluated by a 180° bend test. X-ray diffraction (XRD) and metallography were performed on unbent specimens to characterize the deposit structure. Increasing the anode As/(Sb+Bi) molar ratio from 0.54 to 3.8 resulted in an increase, on average, from four to eight bends to failure in cathode material produced. Significantly lower concentration of antimony (V) in the electrolyte was detected when operating with the higher molar ratio anode. The presence of (111) and (200) planes was noted in cathode material produced from the higher molar ratio anode suggesting that mixed growth character could be responsible for the observed increase in bend test results. The ductility of the starter sheet materials was improved by a higher anode molar ratio.INTRODUCTIONThe presence of antimony in copper electrorefining electrolyte has been reported to cause problems in cathode production (Hiskey, 2012; Peng, Zheng & Chen, 2012; Wang, Chen, Zhou-Lan & Lian-Sheng, 2006; Wang, Chen, Zhou-Lan, Wang, Xiao & Zhang, 2010; Wang, Chen, Zhou-Lan, Wang, Xiao & Tang, 2011; Wesstrom, 2014). To better understand the impact of antimony, laboratory scale electrorefining experiments were conducted using industrial inputs (anodes, cathodes and electrolyte). The influences of anode chemistry on the valences of antimony and arsenic in the electrolyte were monitored and correlated to physical cathode characteristics, such as a bend test to failure and crystallographic orientation.Commercially, starter sheets are produced by electrorefining impure cast copper anodes onto titanium blanks. The starter sheets are then hung in an electrorefining or electrowinning cell using loops of bent starter sheet material. These loops, in the absence of sufficient ductility, fail resulting in cathodes falling into the electrolysis cells. It is thought that the reduction in ductility can be related to anode composition; in particular, the molar ratio of arsenic to antimony plus bismuth As/(Sb+Bi). It has been stated that maintaining this ratio above 2:1 results in numerous improvements to electrorefining operations (Baltazar, Claessens & Thiriar, 1987; Kamath, Mitra, Radhakrishnan & Shetty, 2003; Krusmark, Young & Faro, 1995; Noguchi, Itoh & Nakamura, 1995; Wenzl, 2008)."

Jan 1, 2016

By Changmiao Liu, Dong Dong

"Magnesite is a major mineral resource in China, whose output and export are massive and quite important to the world. Flotation performances of eight anionic collectors on magnesite were studied to find the proper ones. Micro-flotation results indicated that collectors of HOl, SDBS and AEP had outstanding flotation performances on magnesite, with the recovery ratio all reaching above 90% in a wide range of alkaline pulp. Solution chemistry calculation, Zeta potential and FTIR measurements were employed to reveal the interaction mechanism between anionic collectors and magnesite surfaces. Solution chemistry analysis indicated that the main active components of HOl, SDBS and AEP were anions and association complex anions in alkaline pulp. Magnesite surface was negatively charged in the alkaline pulp. The active sites on magnesite surface were mainly the components of MgOH-, Mg (OH)2, and MgCO3 when the pulp pH was over 8. Anionic components of HOl, SDBS and AEP reacted with Mg in magnesite surface to make the insoluble anionic salts. And the chemical adsorption was confirmed by the FTIR measurement evidences.INTRODUCTIONAs an important industrial mineral, magnesite has been widely applied in metallurgy, building materials, chemical industry, agro-pasturage and other fields (Hu et al., 2006). It is a major mineral resource in China with abundant reserves. Its output and export are massive and quite important to the world. Liaoning province is rich in magnesite, whose reserves and production both come first in China. So far the proven reserves have reached 2.91 billion tons, accounting for more than 90% of total reserves in China, and more than 25% in the world (Li et al., 2012).Magnesite ores in Liaoning province mainly contain crystalline magnesite, and the gangue minerals of quartz, dolomite, talc, tremolite, chlorite and carbonaceous materials. Some ores also contain a little pyrite, chalcopyrite, hematite and apatite. Most of the ores must be preprocessed to separate the useful parts from the large amount of gangue minerals, so that their value and industrial application can be enlarged and promoted.Flotation is commonly used to process the magnesite ores, and the conventional flotation methods include anionic and cationic flotation. In the former, gangue minerals of silicates were separated by using amine type cationic collectors. After the impurity minerals were removed, high qualified magnesite concentration could be gained. For the cationic flotation method, it had some drawbacks of lower recovery ratio and poor performance in the lower temperature pulp (Li et al., 1995)."

Jan 1, 2016