Search Documents

By K. Regl, J. Berneder

"AMAG investigated different aspects to improve the resistance against grain coarsening in aerospace alloys during recrystallization and was successful in finding several opportunities to minimize this effect. The studies show that one aspect to counteract grain coarsening is the chemical composition and subsequently all phases that are formed during homogenization. Starting with a fine grain (~ 50 µm) can lead to a final grain size of few mm. On the other hand with a coarse initial grain size (approximately 150 µm) and the right chemical composition the grain size can stay almost constant despite different deformation steps. Additional we investigated different sequences for the component production to eliminate the problem of grain coarsening as a coarse grain has a detrimental effect on product performance.INTRODUCTION In the aircraft industry, aluminium sheets are most commonly deformed in their soft state, followed by solution heat treatment and natural or artificial aging. If the preceding deformation is in a critical amount, during the recrystallization at solution heat treatment grain coarsening can occur. A subsequent deformation to this condition leads to an orange peel surface, which requires additional polishing. Next to this extra effort the coarse grain size produces a drop in the mechanical properties, often below specification limits. If there is no subsequent deformation, this effect is not visible and without destructive testing there is no possibility to detect the error. As mentioned before, this effect occurs during recrystallization, which is a process that is driven by the stored energy in the microstructure. The two most important aspects for an increase of the stored energy are the increase of the grain boundaries fraction (smaller grain size) and the increase of the dislocation density caused by deformation. The increase in dislocation density during the deformation arise from trapping of existing dislocations and from the generation of new dislocations. During recrystallization all grains are built completely new, so all dislocations are removed (Humphreys & Hatherly, 2004). There are three requirements for recrystallization:"

Jan 1, 2018

By G. H. K. Pearse

Sulphur is derived from both 'voluntary' and 'involuntary' production. The former category includes sulphur obtained from elemental sulphur deposits and from pyrite and gypsumanhydrite deposits. Sulphur in the latter category is produced by pollution abatement at fossil Juel plants and from treatment of metallic sulphides. Canada is the world's largest sulphur exporter and third largest producer. Main resources of Canadian sulphur are sulphurous fossil fuels, metallic sulphides and native sulphur. Only the first two sources have produced sulphur in Canada 10 date; the first source accounts for over 85% of total Canadian production. Future sulphur sources will be derived increasingly through pollution abatement and decreasingly through voluntary production.

Jan 1, 1984

By J. F. K. Brown

MR. T. L. McCALL: Planning ahead in coal-mining is essential, but the question may be raised, just how far ahead can we plan. You can overdo it: chat is, you can get in a rut. Never let planning get a hold on you to chat extent. You must be prepared to deal intelligently with any new conditions that arise, and to apply new discoveries. It may become necessary to abandon ? .your plan, make the best you can of the ground you have developed, and start again, with a new plan. So far as the submarine workings of the Dominion Steel and Coal Company are concerned, we cannot know definitely what lies ahead of us under the sea: we must ?base our tentative plans on assumptions, and, as we meet changing conditions, we must change our plans. In the case of inland mines it is possible to bore in advance, and consequently it is generally possible to set out your plans in advance, block out a section of the mine, and develop to obtain a uniform product for a whole year, or perhaps even longer. MR. J. B. MORROW: While planning in coal mining, we must bear in mind chat the consumer also is planning ahead. Some people will tell you that, in ten years time, the demand is going to be all for pulverized co al; others believe that the field for such fuel is limited. Needless to state, planning for a pulverized-coal market is quite a different matter to planning for a general grade, ore stoker, market. In planning, therefore, our endeavour must be to keep a jump ahead of the work being undertaken by the anthracite producers. This year, they are spending about two million dollars-money contributed, not by the Government, but by the industry itself-in the study and promotion of new and improved ways of burning anthracite. For example, they are perfecting small hot-water heaters, and one they have brought out weighs only about ten pounds. I feel that research of this type must be regarded as an essential part of planning in coal mining. We, in the soft-coal industry, are also planning types of more efficient burning equipment and doing other investigational work.

Jan 1, 1937

By Margaret Armstrong, Chris Roth

Abstract -Estimating ore reserves for vein type deposits is a two-stage procedure: first, calculate the geometry of the vein system, and second, estimate the grades within this system. The grade estimation can only be consistently performed if the vein geometry - its size, shape and orientation - has been correctly characterized. Getting the size and shape of the different veins right means that the ore tonnages will not be artificially inflated, e.g., by falsely classifying host rock as veins. Similarly, correctly estimating their orientation and location helps mine management decide on the appropriate mining technique, selective or not. When applying geostatistics to estimate the vein geometry all available information needs to be used and not just the standard lithologic indicator of being or not being in a vein.

Jan 1, 1998

By A. Pearson, Auld. F. A., S. O. Colbeck

"To minimise mine shaft maintenance over the long-term, some potash mine shaft sinking projects have required the provision of a continuous fully welded waterproof steel liner over a substantial depth to achieve zero water ingress. This brings many challenges, including the implementation of a bottom-up construction sequence incorporating extensive waterproof welding and how to ensure the integrity of the welded liner when subject to substantial temperature fluctuations that are likely to occur with a composite steel-concrete liner placed within an artificially frozen shaft excavation. This paper highlights the key challenges and discusses multiple mitigation measures including vertical shaft movement joints and a combined structural-thermal analysis approach. INTRODUCTION Whilst the application of combined steel and concrete shaft liners using a fully welded steel liner is not new and has been used in several previous projects, most notably at Lanigan (Storck, 1968 & Roesner, 1980), recently the need to provide a continuously welded steel waterproof liner for over 800 m length of shaft for a potash mine has been considered. The need for a fully continuous welded steel liner arises from the perceived benefits of providing a fully dry shaft environment to; increase the life expectancy of the shaft; reduce routine maintenance particularly combatting salt accretion and minimising wash down practices; and improve long-term ground stability by preventing salt dissolution. Whereas previous projects have employed discontinuous sections of steel liner, when a fully continuous liner is employed longitudinal shaft strains from thermal changes result in significant deformations that must be either explicitly accommodated or resisted. Note, these thermal vertical expansion forces are more than capable of lifting the shaft collar and head frame structures should they be fixed in place. Typically, shafts are designed to resist vertical forces (collar loads and self-weight) by creating mechanical interlock with the adjacent ground. In competent rock this occurs incrementally with the construction of the shaft liner, and occasional hitch/crib structures are constructed as intermediate foundations to guarantee the transfer of vertical forces at distinct horizons. Usually this means cribs are constructed at first rock head, above the station level, and at the sump, although sometimes additional cribs are formed when entering and exiting weak strata or when a change in shaft liner construction is required."

Jan 1, 2019

By G. Titichoca

Modification of the blasting process considers that any increase in the energy consumption generates greater benefits if done in the later stages (associated with a larger decrease in energy consumption). Therefore, although the blasting cost is doubled, generating a greater proportion of fines in addition to a weaker ore (because with greater loads and appropriate distribution of explosives a greater number of internal cracks is generated), the reduction of the unit cost that occurs in the grinding stages (SAG and ball mills) generates a positive balance in the overall size reduction process. Codelco Chile, Division Andina, has developed an extensive experimental plan to evaluate the concept of blasting modification applying greater energy. This was implemented in two stages, each including a specific mine sector: La Union and Don Luis. This paper reviews the experience of implementing such blasting modifications at the La Union mine and its impact on the design concepts and the operation of the SAG mill plant

Jan 1, 2007

By Michael Boyle, John Zeni

"The Blind shaft boring method is a mechanised process of excavating large diameter vertical shafts downward from the surface. It is a rotary drilling technique eliminating any requirement for personnel to enter the shaft or access underground workings during drilling and lining phases. Excavated material is delivered to surface carried by a flow of circulating fluid through the centre of drill rods. The drill assembly is suspended from a large A-frame rig and powerful winch at ground level providing vertical thrust to a hard rock cutter head. INTRODUCTION The Southern Coalfields Ventilation Shaft was constructed at a mine, 45 km north-west of Wollongong. The 5 m finished diameter (6.2 m drilled) shaft reaches a final drilled depth of 517 m, the deepest, fully lined blind bored vent shaft to date in Australia. Operated by a mining company in the Southern Coalfields, the expanding mine required a new ventilation shaft and associated surface infrastructure to service future operations. An assessment of future ventilation requirements for the coal seam operations identified a need to improve the capacity and reliability of the existing underground ventilation system in order to ensure a safe and efficient underground working environment. Installation of the new upcast ventilation shaft was determined to be the most cost effective and reliable solution to provide adequate ventilation for underground operations. The completed shaft is smooth and fully lined with steel/concrete composite liners that are hydrostatically sealed. The shaft lining is designed to meet the mine ventilation requirements for a service life of 20 years. The shaft intersects the top of the working section of the coal seam at approximately 513 m of depth. This includes the shaft collar depth and shaft bottom profiled intake section.PROJECT METHODOLOGY AND INDUSTRY BEST PRACTICE The shaft was drilled using the blind bore method, an innovative construction technique and an alternative to the traditional methods of sinking deep and large diameter shafts, such as raise boring and conventional drill and blast shaft sinking. The blind bore method allows the shaft to be drilled from the surface down without anyone having to enter the shaft or the mine during the construction process. This is by far the safest method of shaft construction and is especially suitable for difficult ground conditions where there may be unstable or water-charged strata. As this method involves drilling from the surface downward, shafts can be completed ahead of the underground mine development. Thus, allowing underground operations to focus on development and production without the conflicts of managing ventilation priority for underground contractors and mucking out spoil from excavation workings."

Jan 1, 2019

By K. Bunney, R. Pleysier

The deportment of a suite of elements through representative gold ore processing unit operations in cyanidation has been investigated. Chromium and lead are not soluble in alkaline cyanide solutions. Arsenic, antimony, cobalt, molybdenum, selenium, tellurium and vanadium are soluble, but typically do not adsorb onto activated carbon to any appreciable extent. Silver, copper, cadmium, mercury, nickel and zinc to varying extents report along with the gold to the carbon eluate. Cadmium, mercury and zinc can report to the carbon regeneration kiln off-gases. Strontium is soluble and adsorbs on carbon where it remgins.

Jan 1, 2011

By A. E. McIlhinney, I. E. Puddington, C. E. Capes, A. F. Sirianni

"Two main problems are associated with the removal of pyritic sulphur from coals. The first is due to the fine state of dissemination of pyrite, which requires grindin1 to a very fine size to accomplish liberation. The second problem is caused by the similar surface chemical characteristics of coal and pyrite, which complicates separatio11 methods based on this property. In the work described here, the problem of fine particle size was overcome by using the selective oil agglomeratioa method developed at the National Research Council of Canada. Recovery of more than 90% of the combustible values was possible, even with particles only a few microns in diameter. Experiments using conventional chemical depressants for pyrite met with little success. It was found, however, that pyrite may be rejected during coal agglomeration through treatment with the iron.oxidizing bacteria, thiobacillus-ferrooxidans. The conditions for maximum pyrite separation are described and possible mechanisms by which the bacteria act are discussed."

Jan 1, 1973

By M. W. Bates, A. L. Mular

This paper, based on work carried out at Queen's University, describes the development and use of mathematical models of the parallel cyclone classifiers being used in the Strathcona mill of Falconbridge Nickel Min.es Ltd.

Jan 1, 1971

By Y. Hayashi, A. Fuwa

To analyze zinc vaporization kinetics of zinc smelting slag in the ISP furnace, reduction reaction rate of zinc oxide from ZnO-FeOx-CaO-SiO2 slag system with CO-CO2-Ar gas mixtures has been measured by a therm o-gravim etric apparatus at various ZnO content, Pco, and temperature. The reduction rate was measured under a chemical reaction control in the initial three minutes where surface zinc content can be assumed constant. Through the reaction rate dependency analysis on ZnO contents, Pco and temperature, discussion has been made on its reaction mechanistic information in terms of rate coefficient, adsorption/desorption mechanism and activation energy.

Jan 1, 2008

By H. J. McQueen

Before 1950, hot working was simply deforming above the recrystallization point and gave a soft product compared to cold working. From 1960 onwards, improved testing in compression and torsion (stress, strain rate, temperature, quenching) provided valid specimens for microstructural analysis by polarized optical and transmission electron microscopy (TEM). Indeed, TEM was essential to uncovering the hot working mechanisms because it could distinguish between cold and hot substructures (dynamic recovery) in either initial or new grains (dynamic recrystallization). Over the years, teams at Concordia, McGill and UBC obtained NSERC support for students and equipment. CANMET built up a hot forming group having capabilities from high-rate cam-plastometer compression to rolling of experimental alloy billets; this was combined with latest metallographic instruments for fundamental research. Al alloys of every class (2000, 3000, 5000, 7000, 8000) were studied to understand the effects of solutes, precipitates, dispersoids and composites. The complex flow patterns in extrusion were clarified and modeled by finite element methods. Physical simulations of rolling schedules (up to 20 passes and reductions of 98%) by torsion provided evidence of microstructure development during both the passes and the softening intervals, thus clarifying development of texture in different alloys. The results frequently appeared in proceedings of Light Metals symposia and Canadian Metallurgical Quarterly

Jan 1, 2011

By E. Ghali

For engineering applications, magnesium is usually alloyed with one or more elements which include aluminium, manganese, rare earth metals, lithium, zinc, and zirconium. Under normal environmental conditions, the corrosion resistance of magnesium alloys is comparable or better than that of mild steel. The oxide film thickness on pure magnesium after exposure for only ?10 seconds at ambient temperature is 2.2 ± 0.3 nm. Exposure to humid air or to water leads to the formation of a thick hydrated amorphous film that has an oxidation rate less than 0.01 pm/ y. E-pH diagram and high temperature corrosion are discussed. The pH values between 8.5 and 11.5 correspond to a relatively protective oxide or hydroxide film that is more stable at higher pH. Structural applications of magnesium alloys are limited by creep strength rather than by oxidation. Active and active-passive behaviours of magnesium alloys are discussed. The pilling Bedworth Ratio values of oxide and hydroxide are 0.79 and 1.77 respectively and so the formation of Mg(OH)2 inside the oxide film could lead to the development of cracks. Microbiologically influenced corrosion and rational biodegradation of magnesium alloys are discussed because of their interest for medical care.

Jan 1, 2006

By Floyd Smith

Based on underground observations made in .the coal mines of the Dominion Coal Company Ltd., this paper deals with the stress phenomena in the approach roads and headways and in the gob areas associated with the longwall method of total extraction. The deformation of roadways during development and the deformation of roadways during the total extraction period is delineated and presented in graphical form .. Conclusions are made as to the feasibility of the introduction of the retreat method of longwall extraction in one of the colhenes. The importance of future studies are enumerated, especially. those pertaining to the determination .of the opti.m.um sizes of protective pillars and to increasing the efficiency of the current methods of artificial roadway support.

Jan 1, 1967

By P. N. Calder, D. B. Apel, S. D. Butt

Mine-wide (MW) microseismic systems use widely spaced transducers to determine the source location and parameters of stronger microseismic events, while high frequency (HF) systems use fewer transducers to monitor local areas for the weaker events that can precede stronger events. Previous monitoring at the Creighton Mine indicated that an HF transducer located 120 m away from an active stope recorded two types of activity in response to production blasting: the first occurring at the same time as the production blasts and associated with the passage of the direct seismic waves from the blast through the local area, and the second occurring several hours later and associated with the arrival of a slower moving stress change through the rock mass (which was identified by the mine’s MW system). Interpretations of locally increased stress levels, based on analysis of the recorded HF events, correlated with the nearby occurrence of two strong seismic events. These results were applied to a similar monitoring trail at the Kidd Creek Mine where the transient stress changes induced by several development blasts were monitored. It was observed that increases in HF activity corresponded with the occurrence of MW events near the transducer location, and that fewer HF events were recorded the longer this occurred after the blast. Local geological features appeared to influence the number and occurrence of both HF and MW events.

Jan 1, 2000

By A. Ignatow

"A review is made of some of the principal factors and conditions that are, and will be, important to the over-all market climate for asbestos fibre and for the future of Canada's asbestos industry: - health hazard associated with asbestos exposure;- uncertain international regulatory environment for continued asbestos use;- adverse public reaction to asbestos;- product liability/litigation costs (U.S.A. primarily);- promotion of substitution by governments and asbestos user industries; and- minimal product and market development efforts by asbestos producing and consuming industries.In addition, Canadian producers, who export some 95 per cent of their production, face additional constraints:- dramatically reduced integration with asbestos-consuming industries;- 60 per cent of exports to most rapidly declining markets (U.S.A., Europe);- increased competition from offshore producers favourably located to growth markets in developing countries;- increasing production costs;- a strong dollar;- disadvantageous freight rates; and- loss of price leadership and price erosion.Future market trends, as well as prospects for Canada's asbestos industry, will be projected in this paper.Economic FactorsTable 1 presents asbestos fibre production in all countries for the period 1980-82. In certain instances, e.g. U.S.S.R. and China, these are capacity estimates as production statistics are not officially published. The U.S.S.R, by far, is the world's largest producer accounting for some 50 per cent of world production, though most production is consumed internally or by COMECON countries. It is estimated that some 700 plants produce asbestos-containing products within the U.S.S.R.Canada accounts for some 25 per cent of world production though it ranks first in world trade. Other important producers are South Africa Zimbabwe, Brazil and Italy. Since 1979, Canada's asbestos mining industry has experienced a dramatic drop in production and exports of asbestos fibre, as demonstrated in Table 2."

Jan 1, 1985

By F. Filzwieser, K. Gamweger

The process of gas purging in molten aluminium has been an industrial practice in Europe for many years. The advantages are a reduction in the hydrogen content and impurities in the melt, as well as a homogenisation of the temperature and chemical analysis in the molten metal. Formerly used lances or impellers are being replaced by porous plugs which are installed at the bottom of the furnace. This special product of RHI Refractories has proven its efficiency in primary melting as well as in die cast, sheet and extrusion plants.

Jan 1, 2004

By F. Roemer, D. Goldmann, T. Elwert

Tantalum is an important minor metal for the production of high performance capacitors. Approximately 60% of the annual tantalum production is used in this application. Despite its high price of 298 US$/kg (average price 2010–2014), at the moment, no recycling from end-of-life products takes place. In the established recycling processes of waste electrical and electronic equipment (WEEE), tantalum is lost in the slags of copper smelting, where it is highly diluted. An economic recovery is not possible at that point. Although tantalum must therefore be extracted from the WEEE stream before it enters smelting, no industrial recycling processes exist. The main reasons are its low concentration in the WEEE stream, lack of information about tantalum bearing devices, technical difficulties of extraction, and conflicts of interests regarding the recycling of other valuable metals in WEEE. In this paper, the results of a cooperation research project are presented. The aforementioned challenges are addressed and a novel tantalum recycling process is developed. Small pilot scale experiments show that a mechanical processing route can produce marketable tantalum-concentrates of 30% tantalum with yields between 60 and 70%. This is reached through a manual pre-sorting of potentially tantalum bearing products followed by a combination of an optimized comminution, sieving, air classifying, eddy-current (EC), and two stage magnetic separation. Key to the implementation of this process was a detailed survey of the tantalum concentrations in different products carried out by the industrial partner.

Jan 1, 2016

By Mohan R. Srivastava

- OUTLINE - apologies and explanations - a quick bit of history - the wisdom of Wikipedia - ?Matheronian geostatistics continued to convert Bre-X?s bogus grades and Busang?s barren rock into a massive phantom gold resource?? - variogram analysis for Busang - would variogram analysis (or variance analysis) have revealed the fraud? - what went right, what went wrong

May 1, 2007

By J. E. Dutrizac, J. M. Zinck

Ferrihydrite is often the initial precipitate resulting from the rapid neutralization of Fe(III) sulphate solutions, and it seems to be a major constituent of zinc plant neutral leach residues. The most important parameters affecting ferrihydrite precipitaton are temperature, solution pH and the neutralization rate. Low temperatures and rapid neutralization rates yield poorly filterable ferrihydrite, whereas higher temperatures and slower neutralization rates produce readily filterable precipitates; in all instances, however, the precipitates are two-line ferrihydrite. Significant amounts of Zn are incorporated in the ferrihydrite precipitates, and the Zn contents increase with increasing Zn concentration, pH or temperature. Generally, the sulphate contents of the precipitates decrease as the Zn contents increase, and this may indicate that the Zn is adsorbed on the ferrihydrite. Discrete Zn phases were not detected. Neither Cd nor Tl is precipitated with ferrihydrite, although thallium jarosite co-precipitates with ferrihydrite at high Tl concentrations and elevated temperatures. Virtually all of the Sn added to the solution precipitates with the ferrihydrite, but the tin is believed to be present as intimately admixed amorphous SnO2.nH2O. Although selenite extensively precipitates with the ferrihydrite, selenate remains mostly in solution, likely because of the close similarity of the SeO4 2- ion to the SO4 2- ion which is present in high concentrations and saturates the available sites for anion adsorption.

Jan 1, 1998