Search Documents

By Witold J. S. Ostrowski

Stabilization of water-bearing sediments by the freezing method for shaft sinking has been used for over 80 years on the European Continent. The real application of this method in Canada started with the development of the potash mines in Saskatchewan during the past fifteen years. The great depth to which it is applied creates a number of problems which have to be seriously considered by engineers in order to produce a safe and economical design. Freezing depth, thickness of the ice wall, number of the freeze holes, capacity of the freezing plant, pre-freezing time, etc., are the most important points which have to be established. Recent field experience in freezing to great depth in the Saskatchewan area is immensely interesting and important for further development of our potash mining and the application of the freezing method.

Jan 1, 1967

By M. J. Latva-Kokko, T. J. Riihimäki

"Oxidation autoclaves are normally operated at elevated temperature and pressure. The improvement in kinetics is due to combined effect of temperature and partial pressure of oxygen. In this paper exclusive effect of pressure has been studied with a low grade sulphide ore at below 100 °C temperature. These studies are related to development of a novel tower-like reactor that utilizes hydrostatic pressure. Technology is designed to generate high amount of effective fluid volume for high solid content slurries with lower energy consumption and improved kinetics compared to normal atmospheric operation.INTRODUCTIONEconomical utilization of low-grade ores requires handling of enormous amount of material. This sets new requirements for process equipment in terms of size and energy efficiency. For example on the field of mineral processing this has lead to a six fold increase in the operating volume of mechanical flotation cells over the past two decades. Ore beneficiation methods like flotation greatly reduce amount of material that needs to be further processed in smelters or hydrometallurgical refineries. However with some ore types, such as nickel laterites and refractory gold ores, traditional concentration technologies cannot be utilized. Thus direct leaching of ground ore could be an attractive option. In many cases normal atmospheric tank leaching has traditionally been a non-feasible option mainly due to high capital and operational expenses induced by large amount of stirred reactors required. Main restriction for increasing reactor size to beyond 500 m3 has been mechanical load and power requirements set by mixing in cases when high dispersion efficiency of gas is required. THEORETICAL BACKGROUNDIn hydrometallurgical industry autoclaves are typically operated at elevated temperature and pressure. In many cases increase in operating temperature is the desired phenomena and improvements in kinetics are strongly related to that. Thus increase in pressure might be induced solely by water vapor pressure. However when gaseous feed is present, pressure itself has a strong effect on leaching kinetics for various reasons and its role should not be neglected."

Jan 1, 2012

By J. Keough

During industrial electrowinning of copper, uneven growth can impact current efficiency, cause short-circuits in the cell and negatively impact the final quality of the metal product. Copper electrodeposits can be made smoother by incorporating a host of additives in the electrolyte but uneven copper growth may still occur due to variations in electrolyte composition throughout the cell-house. To quantify roughness, 3D images of the surface may be combined with scaling analysis to gain further insight into the deposit structure. Moreover, scaling analysis may offer a method to predict long-term deposit structure using short-term copper deposits. In this paper, the application of Atomic Force Microscopy (AFM) and scaling analysis are used to monitor copper growth and extract surface roughness characteristics. The cathode was a 304 stainless steel disc that was polished to a mirror finish. Copper was deposited onto this surface over a range of 10, 20 and 30 minutes from an acidic sulfate solution (40 g/L Cu) at 40oC from an electrolyte that contained or was free of guar. AFM images were acquired to obtain 3D topographical information on the samples and scaling analysis was performed to extract the root-mean-squared (rms) roughness, periodicity (grain size), aspect ratio of surface features and growth mechanism. INTRODUCTION During the process of copper electrowinning, the dissolved metal ions are reduced and thereby deposited onto a cathode substrate which is later recovered by stripping the metal from the cathode surface. Although this process is widely used in the industry, the conditions of the deposition procedure may cause the growth of the metal product to be uneven which can not only impact the current efficiency and final copper product quality but may also lead to plant interruptions through short-circuits if the anode and cathode make contact. To create more uniform copper deposits, a host of additives may be included in the electrolyte which may act as brighteners, leveling agents and inhibitors which may include guar gum, glue, thiourea or polysaccharides or polyacrylamides and their industrial use has changed over time (Moats, Luyima, & Cui, 2015). As such, the electrolyte composition is often complex and subtle variations in the solution matrix throughout the cell-house may impact the surface morphology of the final copper product. In an effort to quantify the roughness of copper samples, image analysis is often applied and may include Scanning Electron Microscopy (SEM) or Atomic Force Microscopy characterization. While both are appropriate, AFM offers 3-dimensional information which may be used to both qualitatively and quantitatively characterize the surface characteristics.

Jan 1, 2019

By M. Rafiee

Indoor physical security, as a perpetual and multi-layered phenomenon, is a timeintensive and labor-consuming task. Various technologies have been leveraged to develop automatic access control, intrusion detection, or video monitoring systems. Video surveillance has been significantly enhanced by the advent of Pan-Tilt-Zoom (PTZ) cameras and advanced video processing, which together enable effective monitoring and recording. The development of ubiquitous object identification and tracking technologies provide the opportunity to accomplish automatic access control and tracking. Intrusion detection has also become possible through deploying networks of motion sensors for alerting about abnormal behaviors. However, each of the above-mentioned technologies has its own limitations. This paper presents a fully automated indoor security solution that leverages an Ultra-wideband (UWB) Real-Time Locating System (RTLS), PTZ surveillance cameras and a Building Information Model (BIM) as three sources of environmental data. Providing authorized persons with UWB tags, unauthorized intruders are distinguished as the mismatch observed between the detected tag owners and the persons detected in the video, and intrusion alert is generated. PTZ cameras allow for wide-area monitoring and motion-based recording. Furthermore, the BIM is used for space modeling and mapping the locations of intruders in the building. Fusing UWB tracking, video and spatial data can automate the entire security procedure from access control to intrusion alerting and behavior monitoring. Other benefits of the proposed method include higher accuracy and robustness, more complex query processing, and interoperability with other BIM-based solutions. A prototype system is implemented that demonstrates the feasibility of the proposed method.

Aug 1, 2013

By Kevin J. Melong

"Redpath Canada Limited and joint venture partner Thyssen Mining and Construction Canada have recently completed the sinking of the Scissors Creek service in Saskatchewan through its joint owned company, Associated Mining Construction (AMC). The Scissors Creek service shaft was sunk at Nutrien’s Rocanville mine. The following paper outlines the shaft sinking plant and the methodology related to sinking and shaft lining. KEYWORDS Hydraulic shaft jumbo, Hydraulic shaft mucker, Potash shaft sinking, Shaft lining, Sinking galloway INTRODUCTION The sinking and lining of shafts at mines to access mineral deposits has always been one of the great mining challenges for owners, engineers and contractors. Over the course of history in Canadian mining, the sinking of potash shafts through the notorious Blairmore formation of Saskatchewan has proved to be some of the most challenging shaft sinking projects on record. There is no doubt that today’s shaft sinking business demands the utmost in safety performance while delivering projects within schedule and budget. Given these requisites, Redpath and TMCC (executed under the joint venture company, Associated Mining Construction or AMC), were taxed with developing the shaft sinking system to deliver this program in the safest and cost effective manner, with due regard to schedule and quality. Traditionally the potash shafts sunk in Saskatchewan involved a significant level of manual labour, owing to the methodology of excavation by means of chipping the frozen shaft sections with hand held pneumatic machines, and manually placing tubbing segments or steel liners of the shaft lining system. Most certainly, the AMC team wanted to make a step change from those earlier sinking programs and develop systems for sinking this potash shaft that removed the high level of manual work, thus making this project inherently safer, while endeavoring to sink more efficiently. With that in mind, the team embarked on a design program to improve its overall shaft sinking systems without the requirement for excessive capital and methodology flexibility to adapt to potential changing conditions expected to be encountered during shaft sinking. This was especially important should the new approach be met with less than expected success, and retrofitting of the system was required. The concepts were developed to provide for a much improved work environment, while easing the manual labour burden on the workers with innovative equipment and approach to the work."

Jan 1, 2019

By Patrick Fantin

Mining ? The Past Safety Not a priority; Health Not a priority; Energy Manual Labour; Horsepower? Literally. Financially Robust For the Owner?s; Mining ? The Future Safety Zero Harm Health Understanding and elimination of Industrial Disease Energy Efficient use of energy through technology. Full value of renewable energy. Financially Robust Continually build shareholder value through optimum CAPEX/OPEX.

May 1, 2013

By S. Nafisi

Permanent mould casting may be regarded as a near net shape manufacturing process where simple to very complex shaped engineering components are fabricated with high degree of precision in a metallic mould, In this group, High Pressure Die Casting (HPDC), have attracted more attention because of its production rate, where both liquid and semisolid metals (SSM) can be cast with high degree of precision and versatility. The SEED process, Swirled Enthalpy Equilibration Device, the new process for semi solid metals slurry production route, consists of two steps: The initial step involves extracting specified amount of heat from the molten metal to generate liquid-solid slurry, i.e, mushy structure, followed by drainage of remaining liquid to produce a compact free standing feedstock for rheocasting operation. In this paper, microstructural evolution during the process and some initial casting results of automotive components an also reported.

Jan 1, 2005

By M. D. Griffith

"Ventilation models are a vital tool to ensure ventilation designs can provide airflow to all work areas in a mine. Airway resistance and variations in natural ventilation pressures will affect simulated airflow and heat distribution through a mine. Validating ventilation model resistances and pressures to the exact underground conditions can be difficult and the variances can contribute to significantly different simulation results depending on the structure of the ventilation design. The study will use sensitivity analysis to explore examples of variability of simulated airflow due to small resistance, heat and natural ventilation changes and thereby help the user identify both trustworthy and potentially unreliable parts of a mine ventilation model. INTRODUCTION Mine ventilation network modeling is a vital tool for ventilation professionals and has become increasingly relied upon during the design and operation phase of mine ventilation systems. However, they provide only an approximation of reality, and caution must always be exercised when drawing conclusions or making decisions based on simulated data. Ventilation modelling should be performed by persons with a sound fundamental knowledge of ventilation and ideally should be validated with field data, but in large mines, or mines which are yet to be mined, accurate input of the simulation variables can be difficult, and errors and inaccuracies may be difficult or impossible to avoid. This study discusses and investigates the sensitivity of the mine ventilation simulation results to input errors. In addition, there are limitations to what steady-state airflow and heat simulations can model, regardless of the accuracy of the model inputs. In some situations, steady-state solvers cannot capture the dynamic changing behavior of a ventilation system. This study will also describe and apply techniques to analyze the natural variability of mine conditions on ventilation models. The consequences of poor accuracy in some parts of a mine model may impact on the health and safety criteria of ventilation designs. For example, if an airway is required to flow in a particular direction and quantity, then despite a ventilation model showing correctly designed conditions, small errors in input values may result in incorrect prediction of the direction or quantity of airflow. This may create unexpected buildup of heat or gases during operational activities, causing safety issues or operational delays. The ability to know which parts of a mine ventilation model have increased potential for poor simulation results will allow engineers to consider the ventilation design and make changes if required to better guarantee the required design flows."

Jan 1, 2019

By E. Peek, L. Becze, K. Reading

"Gallium oxide is an important semiconductor material used in optoelectronic devices (flat panel and solar cell) catalysts and sensors. One of the methods to produce ?-Ga2O3 is the so-called hydrothermal route. It is practiced by Neo Gallium Compounds and comprises of two steps: (1) the production of mainly gallium-oxy-hydroxide in a pressure vessel by reacting metallic gallium with water at 200-220 ºC and (2) the calcination of gallium-oxy-hydroxide at 700-750 ºC to convert it into ?-Ga2O3. This paper describes this pressure hydrometallurgy process supported with relevant thermodynamic data and presents the characteristics of the ?-Ga2O3 powder produced for commercial purposes. INTRODUCTIONGallium is a relatively new metal, having been predicted by D. Mendeleev in 1871, discovered by P.E. Lecoq de Boisbaudran in 1875, and first commercially produced in the USA in 1943. Gallium is not rare, being more abundant in the earth crust than antimony, bismuth, molybdenum, silver and tungsten. However, few gallium minerals exist in nature, and the dispersion of gallium within other minerals add to the complexity of its recovery. In practice, gallium is found in dispersed state primarily in bauxites and in some sphalerites, and, to a much smaller extent, in some coals. At present, a very large proportion of the primary gallium in the world is recovered as a by-product of aluminum plants, mostly Bayer plants, where gallium is extracted from a bleed of the Bayer liquor (Roskill, 2011). In 2011, world production of primary gallium was estimated at 200 metric tonnes. In addition, there is a significant contribution of recycling to the overall yearly availability of the metal.Gallium exhibits fairly remarkable properties: it is liquid above 29.76 ºC, can be supercooled, and with its high boiling point (2204 ºC), is the metal with the widest liquid range. Gallium is magnetic, and is an excellent conductor of both heat and electricity. Gallium also displays a marked anisotropic electrical conductivity (Roskill, 2011). All these properties render gallium almost irreplaceable in the semiconductors (GaAs, GaN, GaSb, GaP wafers) and the optoelectronics industry (flat panel, solar cell)."

Jan 1, 2012

By J. D. T. Steyl

"This paper presents a phenomenological model of the rate of iron(III) precipitation in batch and continuous autoclaves at medium temperature operating conditions. The rate expressions are based on information obtained from the literature and experimentation at low and high pulp densities. Special allowance is made for the formation of surface nuclei, which appears to be promoted at a higher iron(III) precipitate surface area, especially in suspensions of lower terminal acidity. This leads to the formation of secondary particulates and provides the required link to simulate high pulp density leaching-precipitation systems, using low pulp density batch precipitation data. In particular, the model allows direct application of the simulation to the autoclave oxidation of iron-containing copper sulfide concentrates and provides a good estimation of the relative precipitation rate of hematite, the preferred product, compared to hydronium jarosite. Some interesting mechanistic understandings of iron(III) precipitation in autoclaves are further elucidated.INTRODUCTIONThe objective of this work is to describe the rate of iron(III) precipitation and the relative amounts of hematite compared to hydronium jarosite precipitation during batch and continuous chalcopyrite oxidation under medium temperature (MT) (~130 to 160ºC) autoclave conditions. Published information has not yet revealed sufficient mechanistic insights about this sparingly soluble salt system under these conditions. The rate expressions in this paper are based in part on current literature information, supplemented by qualitative experimental observation at low pulp density conditions, in particular the high-resolution backscatter electron (BSE) images and particle size distributions (PSDs) of the precipitates. A summary of this work and insights from the literature are presented first, after which the behaviour of iron(III) in high pulp density leaching systems is used to derive a phenomenological expression of the effect of existing iron(III) precipitate surface area on the precipitation rate. The overall regression encapsulates all the experimental results, i.e., those obtained in both batch and continuous autoclave configurations (Steyl, 2012a)."

Jan 1, 2012

According to the principle of similarity, the physical and chemical configurations of a system can be defined by ratios of magnitudes within the system and do not de-pend on the size or nature of units of measurement. In the present work, the similarity principle was utilized in evaluating the reducibility of various iron ores in a rotary batch furnace under optimum operating conditions. It was then used successfully to extrapolate the results, first to the operation of a 20-ft. pilot-plant kiln and then to an industrial-size 80-ft. kiln. By means of this systematic analysis of kiln operation, it was possible to increase the production capacity of the kiln considerably. T HE kilns used by the Strategic-Udy process for the partial reduction of iron ores are, in most aspects, similar to conventional calcining kilns. Iron ore is fed continuously in the upper (feed) end of the kiln and, as the latter rotates

Jan 1, 1964

By D. V. Ziehlke, J. M. Franklin, T. M. Gordon, A. G. Galley

The Snow Lake-Wekusko Lake region of northern Manitoba conta ins numerous lode gold occurrences, including the largest gold deposit in the Churchill Prov ince, the Nor Acme mine. The Aphebian volcanic and sedimentary rocks of this region are comprised of submarine volcanic strata, overlain by turbidites, both of the Amisk Group, and fluvi atile sedimenta ry strata and bimodally composed subaerial volcanic rocks of the overlying Missi Group. Gold occurs as: 1) accessory gold in volcanogenic massive sulphide deposits, 2) lode gold in shear zones related to sy n- to post-FI thrust fa ults, and 3) lode-gold associated with post-F2 fault . An alteration a emblage of biotite, al bite and calc ite is associated with both groups of lode-gold deposits, and has been superimposed on the regionall y-developed metamorphic assemblages. AJthough these deposi ts are spatial ly related to britt le-ductile faul ts of different initial ages, they appear to have all fo rmed after the major period of reg ional fo lding and metamorphism, and thus may be penecontemporaneous. The alteration is different from the sericite-ankerite-quartz assemblage that is typically associated with gold deposits in Superio r Prov ince. Deposits in thi s area of Churchill Prov ince may have formed either at a higher temperature or a deeper structu ra l level than tho e in Superior Prov ince.

Jan 1, 1986

By J. Olaf Sund

"The New Brunswick gypsum and an-hydrite deposits make up part of the Windsor group in the Upper Mississippian. The present deposits were formed by surface hydration of the underlying anhydrite beds. The sub-hydrate, hydrate, and di-hydrate stages of gypsum are formed from the anhydrite by this hydration. The anhydrite was precipitated from sea water in embayments that were separated from the sea by a reef or bay-mouth bar. The anhydrite is the original form of the calcium sulphate precipitate.One gypsum deposit near Plaster Rock in northern New Brunswick was precipitated from sea water directly as gypsum, which is its present form."

Jan 1, 1960

By C. J. Hodgson

"IntroductionThe Kitsault molybdenum mine is located 600 m above sea level on Lime Creek at the head of the inlet of Alice Arm, 140 km northeast of Prince Rupert, British Columbia (Fig. 1). The area of the mine is characterized by rugged topography and deeply incised creeks which drain into the Portland Canal - Observatory Inlet fjord system. Access is by air service or boat from Prince Rupert, or by secondary road from Terrace.HistoryThe deposit was first staked in 1911, at which time the main feature of interest was a polymetallic vein with values in silver located southeast of the molybdenum deposit (Woodcock and Carter, 1976). Turnbull (1916) was the first to describe the extensive zone of crisscross quartz stringers with Mo~ on the banks of Lime Creek which, although it clearly had the potential to contain a major deposit, was not then believed to be of commercial value.Following sporadic work through the 1920s and early 1930s, the ground lay idle unti11959 when Kennco Explorations (Western) Ltd. commenced a program of systematic diamond drilling on the stockwork-type mineralization adjacent to Lime Creek. In late 1964, Kennco announced the presence of an orebody of 36 million tonnes averaging 0.230Jo Mo~ which was to be put into production at a rate of 5450 tonnes per day under a new subsidiary, British Columbia Molybdenum Ltd., at a forecasted capital cost of $20 million (revised to $30 million).Between January 1968 and April 1972, 10.4 million kg of molybdenum were produced from 9.3 million tonnes of ore, at an average mill recovery of 90%, and with an average mill head grade of 0.206% Mo~. The ore was mined in an open pit with a waste to ore stip ratio of 1.5 to 1. The. operation was terminated in 1972 due to weak molybdenum prices and escalating costs.In May 1973, the deposit was purchased by Climax Molybdenum Corporation of British Columbia, Limited and in 1979 transferred to affiliate Amax of Canada Limited. In early 1979, following completion of detailed feasibility studies, Arnax commenced construction of the 10 900 tonne per day Kitsault mine and mill complex based on a mineable open pit reserve of 95 million tonnes at an average grade of 0.192% Mo~, sufficient for a mine life of 25 years. The original capital cost estimate was $143 million; it subsequently escalated to approximately $200 million."

Jan 1, 1995

By James J. Holmes

ACCIDENT prevention as we know and understand it today is of comparatively recent origin. As a matter of fact, the Industrial Accident Prevention Association of Ontario, which is the oldest organization of its kind in the Dominion, celebrated its thirtieth anniversary only this year. On the other hand, one could say that the history of accident prevention is almost the history of mankind itself. In a general sense, every forward step that man has made throughout the centuries has been largely due to two things: (1) a desire for increased comfort, and (2) the need for safety; and, always, the need for safety has taken precedence over the desire for comfort. While it is true that hundreds of volumes have been published, dealing with the many aspects of accident prevention work, you cannot go to a library and pick out a book that has all the answers in it. Such a book has never been published-we are still looking for some of the answers. However, a good deal of real progress has been made.

Jan 1, 1945

By D. Jean Hutchinson, Mark Diederichs

"Cable bolts are an important support component in modern underground mines. If an optimized cable bolt system is to be achieved, it is insufficient to focus on cable bolt layout design or on cable bolt installation in isolation. Cable bolt support, like all engineered systems, requires a holistic approach, encompassing integrated elements of design, implementation and verification. The “Cable bolting Cycle” described in this paper incorporates these components along with related tools and procedures which should be used together to ensure effective and efficient cable bolt support.Design involves the consideration of demand, capacity and constraints as outlined in this paper. The demands imposed on the sup-port system by the rock mass response to excavation under the combined action of stress and gravity must be matched to the capacity of the cable bolt array. The cable bolt system capacity is a function of the component strengths of the steel strand and the bond (load transfer) and by the deformation response and retention characteristics of the system. The design is bounded by operational and economic constraints.Implementation of the cable bolt array can then proceed and must include appropriate protocols of communication, training and quality control, in addition to both general and site specific installation procedures. Implementation will be discussed as the sum of these components.Implementation of the cable bolt array can then proceed and must include appropriate protocols of communication, training and quality control, in addition to both general and site specific installation procedures. Implementation will be discussed as the sum of these components.The information presented in this paper represents a very abbreviated version of much broader concepts, procedures and design charts, presented in a practical cable bolting handbook by Hutchinson and Diederichs (1996)."

Jan 1, 1996

By I. M. M. W. R. Jones

"THE OBJECT of these notes is to initiate a discussion among the members of our Institution on the connotation of the term 'ore', and to arrive, if possible, at an acceptable definition of the term in the light of its current use by our leading mining engineers, metallurgists, •and geologists.The majority of •authors of well-known modern text-books on subjects dealing with mineral deposits define 'ore' in words which convey the meaning that it is an aggregate of minerals from which one or more metals can, under favourable conditions, be extracted profitably.Many eminent members of the Institution, and of mining and metallurgical institutions in other countries, consider that the term should not be restricted to metalliferous mineral •deposits but can also be applied correctly to certain non-metallic deposits. They believe that the growth, during the twentieth century, in the industrial importance of non-metallic minerals, and the progress made in the mining and the milling of deposits containing such minerals by methods similar to those used for metalliferous mineral deposits, no longer justify the academic restriction of the term to deposits worked for their metal content only."

Jan 1, 1954

By G. D. Garland

"IntroductionALTHOUGH the presence of rock salt in the Carboniferous basin of northern Nova Scotia has been known for at least one hundred and twenty years, and salt has been mined at Malagash continuously since 1919, certain characteristics of the deposits make exploration by drilling or surface examination difficult. The surface rocks of the basin are, in general, of Pennsylvanian age, while the salt occurs in the Mississippian Windsor group. The latter rocks are brought to the surface only along anticlinal folds, or as irregular fault blocks. Because of the limited areal extent of these Windsor exposures, and their complicated internal structure, geophysical surveys, especially gravimetric, can be of considerable aid in outlining the more favourable areas.The present paper describes the results of recent investigations by the Dominion Observatory, in cooperation with the Nova Scotia Department of Mines. It includes a regional study of that section of the Cumberland basin lying between Springhill and Malagash ( Figure 1), and a much more detailed survey of the immediate vicinity of the Malagash deposit itself. This deposit had been studied by Miller (6, 7) with the torsion balance nearly twenty years before, and a direct comparison between the results given by the two types of instruments is therefore possible."

Jan 1, 1955

By J. B. Kitchin

"The design of conveyor belting for use in mines poses problems to the manufacturer that are unique. The challenge to be met is that of the production of a conveyor belt which can withstand use and misuse in an environment that may differ vastly from one country to another, and even between one mine and its neighbour.The development of a product to meet such varying requirements necessitates a protracted program of trials, both in the laboratory and in the field; a new successful development, the only criterion, can be said to have been achieved only after very long-term usage under actual, deliberately chosen, arduous mining conditions.New developments in conveyor belt construction can never stop, no more than can developments in new and advanced mining techniques. A new problem is set-an answer must be found. Some of the problems are noted here, and answered where possible, in what must after all be little more than an excursion into a very comprehensive and detailed subject."

Jan 1, 1967

By W. H. Fertl, S. J. Pirson

Well logging techniques, as used successfully in oil and gas exploration, can also be used to give a detailed evaluation of drill holes through industrial mineral deposits such as sulphur. This paper describes the logging tools used gives the theory behind the well-log interpretation and discusses the application of the method in sulphur-bearing limestone and m more complex sulphur deposits.

Jan 1, 1970