Search Documents

By M. G. Mena, M. S. Mena-Junio

Silver (Ag) filler is the most attractive choice among all the conductive fillers of die attach materials for the attachment of silicon devices because of its balanced properties and relatively low cost. However, a major problem of silver is that it electrochemically migrates in the presence of moisture and applied bias. In microelectronic devices, silver migration can occur between adjacent conductors/electrodes, which leads to the formation of dendrites and eventually results in short-circuit failure. In order to assess the reliability of these conductive fillers, an investigation for two types of Agfilled die attach materials was done using the water drop test at room temperature and using a 1000 hour temperature-humidity-bias (THB) test under 85 ºC and 85% RH conditions. Four different bias/voltages and six different electrode distance spacing were used. Both dendrite and cloud/lace-like growths were observed as a result of the electrochemical migration of silver, Water drop test results revealed that increasing the applied bias/voltage and decreasing electrode spacing causes migration to occur faster, thus resulting into shorter time to fail (TTF). It was also observed that the growth rate of the dendrites from the cathode increased linearly as the dendrite approached the anode, probably due to a combination of increased ion availability and electric field. A minimum applied bias of 3 volts was required for migration to occur in Epoxy A as compared to 2 volts for Epoxy C. The higher migration voltage requirement for Epoxy A was attributed to the higher volume resistivity of the said epoxy. In addition to the minimum voltage requirement, it was observed that a minimum electric field of about 1 volt/mm is required for migration to occur. The 1000 hour THB testing did not result into any failures. It is surmised that the presence of condensed moisture is another requirement for migration. Such condition is not present during the THB testing.

Jan 1, 2012

By The Mine Staff

THE PROPERTY of the Lamaque Mining Company, Limited, ?is located in the Town of Bourlamaque, seventy miles east of Noranda, in Bourlamaque township, Abitrbi county, north western Quebec. Gold production commenced at Lamaque in April, 1935, with an initial mill capacity of 250 tons per day. The capacity was doubled in November of the same year, and in December, 1937, it further increased to 1,200 tons per day. During the war years the mill operated at a reduced tonnage, but in 1951 milling units were added along with complementary crushing and shop facilities to bring the capacity to 1,500 tons per day. Finally, in 1953, the capacity was raised to 2,000 tons per day, which rate is being maintained at the present time. The total production at Lamaque from April 2nd, 1935, to December 31st, 1956, has been 9,168,901 tons of ore from which 2,208,168 ounces of gold was recovered. The total value of this production , excluding E.G. M.À.*, was $77,869,653.

Jan 1, 1957

By Harry R. Oldale

This paper first covers the general and economic geology of the Coxheath Hills area, and then outlines the exploration and mining development that has been carried out since the first discovery of copper in the area in 1875. The work of Mariner Mines Limited from 1963 to the present time is detailed, particular attention being paid to the recent discoveries of copper, silver and lead mineralization that have greatly enhanced the potential of the area.

Jan 1, 1967

By R. C. Gegg

The property of MacLeod-Cockshutt Gold Mines, Limited, is in the Little Long Lac area of the Thunder Bay Mining Division, Ontario, about four miles south of the Canadian National railway station of Geraldton. The town of Geraldton is about 170 miles east of Port Arthur and 22 miles west of Long Lac, which is on the main line of the Canadian National railway. The Trans-Canada highway passes through the property and during the winter season the road is maintained between Port Arthur and Long Lac. Electric power is supplied by the Hydro-Electric Commission of Ontario from their Cameron Falls plant and is distributed at 44,000 volts by a local transformer station. Early History The South orebody was discovered by diamond drilling in the spring of 1936. This is a porphyry contact orebody with major pyrite and minor arsenopyrite mineralization. Some gold is present in the 'free' state, but for the most part it is locked in the pyrite, with little or none in the arsenopyrite. Preliminary test work was based on comparing straight cyanidation with bulk flotation and cyanidation of the concentrates. The overall results by the two methods were found similar, but for economic reasons the flotation-cyanidation process was adopted. Before the mill came into operation, a new and entirely different type of orebody, consisting of massive sulphide lenses in banded iron formation, was discovered to the north of the existing workings. These bodies are an intricate mixture of pyrite and arsenopyrite, both carying gold.

Jan 1, 1949

By Daan Maijer, Wade Marquardt, Robert MacKay, Steven Cockcroft, Farzaneh Farhang Mehr

"To comply with the new Corporate Average Fuel Economy (CAFE) standards, the automotive industry is aiming to reduce weight and increase the power and efficiency of small displacement engines through the application of forced induction technologies. As an example, there are now several 2.0 litre turbocharged engines in production, producing in excess of 240 hp. To meet the need for improved fatigue properties in the engine blocks used in these high-output engines, a new water-cooled chill technology is under exploration at UBC in partnership with General Motors and Nemak. A series of experimental techniques were used to assess the capability of the new chill to extract heat from an A319 casting in the vicinity of the main bearing bulk head. The results show that this method has the potential to achieve a reduction in secondary dendrite arm spacing thus meeting the new microstructural specifications for these engines.INTRODUCTION The automotive industry is working to meet the stricter efficiency requirements laid out within the CAFE (Corporate Average Fuel Economy) regulations (Bastani, 2012; Cole, 1995; Mackay, 2011; Miller, 2000), while at the same time not sacrificing performance. One approach is to increase the use of lightweight materials, which leads to a decrease in the overall vehicle weight and fuel consumption (Cole, 1995; Mackay, 2011; Miller, 2000). Other approaches include smaller displacement engines and gas-electric hybrid drivetrains. However, one trend that is becoming clear, is a greater emphasis on force induction gasoline engines. This allows for weight reduction to be achieved with smaller displacement engines without sacrificing performance. One consequence of this approach is that the engine block materials are subject to higher in-service thermal and mechanical cyclic loads (Cole, 1995; Miller, 2011; Heysler, 2001) The fatigue properties of an alloy are strongly affected by a number of the, as-cast, microstructure features including, Secondary Dendrite Arm Spacing (SDAS), porosity and eutectic lamella spacing (including intermetallic ß-Al5FeSi platelets) (Mackay, 2010a; Mackay, 2010b; Viet-Duc, 2015; Casellas, 2005). It is generally accepted they can act as fatigue initiation sites and that a reduction in their size will result in an improvement in fatigue performance. For a given alloy chemistry, one of the key parameters affecting the length scale of all three is cooling rate (Mackay, 2000)."

Jan 1, 2017

Mercapto organic compound SDMP was used as a depressant for separation of copper activated marmatite from pyrrhotite in the presence of butyl xanthate. Flotation results show that SDMP has strong depressing effect on pyrrhotite recovery in the absence and presence of copper ion, but has promotional effect on marmatite recovery when added together with copper ion. The flotation test of mineral mixtures shows that copper-activated marmatite could be separated efficiently from pyrrhotite using SDMP as depressant. Infrared adsorption spectra demonstrate that SDMP has a strong adsorption on pyrrhotite surface through its functional groups such as ?SH, -S03.

Jan 1, 2006

By J. Kramer, T. Hartmann

In the Hydrometallurgical processes, the presence of the so-called “crud” is a constant challenge in solvent extraction. Crud is a stable emulsion which forms along the interface between the aqueous and organic phase. The spread is influenced by the following parameters: first, wind blows the dust and impurities into the open sedimentation tanks. Second, the undissolved solids such as sand transported in the PLS causing problems in conjunction with incorrect agitator design. The crud fraction can decisively impact the efficiency of the hydrometallurgical extraction because the phase interface can constitute a large fraction and the sedimentation tanks cannot react flexibly to it. In the downstream process of the seriesconnected sedimentation tanks, they are thus all contaminated with crud. At the same time, the necessary mass transport is significantly impeded at the phase boundary between organic phase and aqueous phase due to the crud formation. The transfer of the organic phase into the electrolysis cell can result in a “burnout” of the cathode. The carry-over of this electrolyte into the extraction can cause problems with the pH regulation. The carry-over of the organic components into the raffinate also leads to contamination of the leaching circuit. The continuous treatment of the crud with a 3-phase decanter centrifuge is extremely effective in combating this problem. This technology splits all three phases from each other and they are consequently continuously separated. All subsequent process steps exhibit a stable, uniform effectiveness. The main advantage for the customer is that fluctuations in the process are eliminated and the organic phase can be recirculated back to the extraction. The recycling of the solvent alone justifies the investment in less than 6 months as examples from South Africa and Chile show. To operate solvent recovery in daily operation fully automated online at the optimum limit, the decanter centrifuge is equipped with a concentration-dependent pond adjustment called DControl®. By this means, we can guarantee our customers the maximum possible solvent recovery and minimise the solvent costs in this process step. This system is presented in detail in this paper.

Jan 1, 2012

By Georges Houlachi, Raynald Labrecque, Jean-Noël Cloutier

"Electrodialysis (ED) is an electro-membrane technology based on electrochemical process using electrical energy for the production of chemicals. The process can be used for concentrating, extracting, separating products, modifying molecules, purifying solutions, pH adjustment and regenerating salts into their base and acid. This paper reviews the principle of ED, present some of the different options and discuss applications that are relevant to the hydrometallurgy and mining industries for the treatment of effluents focusing on recovery of chemicals (acid and metals) and recycling of water minimizing the environmental footprint.INTRODUCTIONElectrodialysis (ED) is usually defined as an electrochemical separation process in which electrically charged membranes and an electrical potential difference are used to separate ionic species from an aqueous solution and other uncharged components [1]. ED technology consists of an electro-membrane technology based on an electrochemical process using electrical energy for the production of chemicals. It is a method combining electrolysis and dialysis was proposed for the first time in 1890 by Maigrot and Sabates [2]. In the late 1930s Teorell, Meyer and Sievers discussed membrane phenomena, revealed membrane potential, electric conductivity, transport number [3]. Meyers and Strauss introduced a multi-compartment ED apparatus consisting of two electrodes and a stack of ion-exchange membranes between them [1]. They succeeded to double the concentration of a KCL solution [3- Tarleton]. In general, ED consumes less energy than electrolysis to perform salt splitting. In that regard, one can expect an energy reduction of about 30% [4–5]. ED offers a great versatility in the domain of separation processes. Indeed, it can be used for concentrating, extracting, separating products, purifying by desalination, pH adjustment and regenerating a salt to acid and base components. This paper reviews the principle of ED, presents various options available and discusses potential applications relevant to the mining and metallurgy industries with economics of some successful industrial applications."

Jan 1, 2016

By Frederick J. Browne

Water, water everywhere, but not a drop (fit) to drink! Trite, but how often only too true? What is there met with in mining which, under various circumstances, may be said to be the most sought-for and highly-prized and also the most objectionable and most feared? Water! What visions that combination of five letters brings to all thoughtful minds? Up to near the end of the eighteenth century water was thought lo be an element but was then discovered to be the result of the combustion of two volumes of hydrogen with one volume of oxygen, and water so produced is chemically pure. Pure water is a clear and colourless liquid when seen under ordinary conditions, but appears bluish when seen through a long tube, and this same bluish tint may be observed in many lakes, especially those of glacial origin. A story often told describes a prospector in the desert who, failing to find water to replenish his canteen, suffers torture and death under fearful circumstances. Then again we may recall the flooding of mines, where water poured in so quickly that there was no opportunity of saving the unfortunate workmen. Instances might be multiplied without number showing that either the lack or excess of this essential fluid has taken heavy toll of human life. In all branches of mining and associated industries water must be dealt with to a larger extent, from an economic point of view, than any other substance, and very often the purity of the water is a matter of considerable importance.

Jan 1, 1925

By R. H. Nafziger

A novel process has been developed for preparing directly workable steel ingots from prereduced iron ore pellets by a two-stage process. The pellets are continuously charged into an electric arc furnace, where molten metal is separated from the gangue. The molten metal flows out of this furnace through a hollow nonconsumable graphite electrode immersed in a molten flux in an electroslag furnace. The molten metal solidifies on a continuously withdrawing base plate to form the ingot. A variety of standard carbon and alloy steel ingots . free of porosity , were produced using suitable decarburizers and ferroalloy additions. Some advantages of the two-stage process include: (a) consumable electrode fabrication is eliminated; (b ) no expensive deoxidizers are required; (c ) the uncontaminated electros lap flux can be reused; (d) energy consumption averages 25% less than in a conventional electric arc - electroslag operation ; and (e) the operation is continuous.

Jan 1, 1977

By I. Stanoev, V. S. Stoilov, I. Gradinarov, E. D. Visariev, I. A. Bonchev, Aurubis Bulgaria

"Aurubis is the leading integrated copper group and the world’s largest copper recycler. In Copper smelter Aurubis Bulgaria (Pirdop), the residual copper in the slags from Flash furnace and Converters is recovered by flotation. The slag processing comprises: pit cooling, crushing, two stages grinding (autogenous and ball) and flotation. The copper concentrate is thickened and then is filtrated by vacuum disk filter. The thickener overflow is sent to settler for additional clarification. A resent throughput increase resulted in higher solid content in the thickener overflow due to insufficient thickener area. Different scenarios to overcome the issue were evaluated (new thickener, reagents and reconstruction). An increase of the thickening area by installation of lamella modules was chosen as the most promising option. Three lamella modules (1 m3 each) were installed in conventional thickener for the test. Number of sampling campaigns was done to evaluate the effect on solid content in overflow. Parameters of the dewatering cycle were collected during sampling campaign. The products grain size distribution was defined - thickener feed, thickener overflow with and without lamella. The thickener overflow with lamella modules has 2.12 g/L less solid content. The decrease was 71.8%. According to the tests results, the whole conventional thickener was reconstructed with lamella modules. The thickener area was increased by more than 400 m2.INTRODUCTIONIn Copper smelter Aurubis Bulgaria, the copper in slag from the Flash furnace and the Converters is recovered by flotation. The scheme of slag processing is crushing, two stage grinding (autogenous and ball) and flotation. Till 2010 the grinding cycle in the plant was in two stages: the first stage was AG Mill 70×23 working with a classifier and the second stage was ball mill 3.6/5.5 working with a hydrocyclone. In 2010 a new AG Mill 65×78 with hydrocyclone was put in operation in order to increase throughput of the plant. The second stage of the grinding cycle was not changed."

Jan 1, 2016

By P. Ramirez

"To achieve an optimal metallurgical performance in the flotation process the bubble diameter should be between 0.5 and 2.5 mm. To control bubble size, frothers are added, reducing bubble size and conferring bubble stability against coalescence. However, the bubble generation mechanism determines predominantly the bubble size distribution produced. In mechanical flotation cells, bubbles are produced by the shear stress generated by a rotating blade on a gas stream. This mechanism produces a log normal bubble size distribution. In contrast, in column flotation, jetting gas injectors are commonly used in Chile and the bubble size distribution is bimodal with small and large bubbles. Bubbles larger than 2.5 mm mean a loss in surface area, while bubbles smaller than 0.5 mm move with the pulp stream and therefore collide less frequently with particles. In this paper, a new device based on a jetting sparger and a deflector disc (impinging jetting) is evaluated as an alternative sparger for column flotation.The new device was tested in a rectangular acrylic cell 1 m × 0.5 m × 3 m. High-speed cinematography was used to compare bubble generation with jetting and impinging jetting at different gas velocity in the nozzle (5–50 m/s). From the image analysis, it was observed that the deflector induces a shear stress, in analogy to a rotating blade but in this case the shear results from a high velocity gas hitting a static surface. The device was evaluated in a 0.5 m diameter 3 m high column. The McGill bubble viewer technique was used to compare the bubble size generated by jetting and impinging jetting. It was found that the Sauter mean bubble diameter reduced from 7.4 mm to 2.8 mm, when the jetting sparger was modified with the deflector. In the case of the impinging jetting sparger, 70% of the bubbles were in the effective range for flotation, while for the jetting sparger, only 10% were in the effective range."

Jan 1, 2016

By Suman Giri

Non-Intrusive Load Monitoring (NILM) is a method of extracting appliance-level power consumption information from aggregate circuit-level data with the goal of giving users feedback regarding their energy consumption so they can take control of their consumption habits. In this paper, we present a novel algorithm for classification of on and off states of appliances. We compare the performance of our algorithm in on state detection with a pervious paper that evaluated the same dataset and show that it performs up to 13% better. We also present the results of a case study where we collected data for different modes of a cooktop, microwave and dishwasher and used our algorithms to perform power estimation. The error on ten different setups in the test bed ranges from 1% to 32%. We discuss our results and lay out ideas for future work.

Aug 1, 2013

By J. L. Jambor, M. J. Baker, M. J. Logsdon

"Abstract - Prior to the development of the Diavik Diamonds Project, baseline studies were conducted to determine the geochemical characteristics of four kimberlite orebodies as an aid in the design of both the water-management system and the facilities for containment of processed kimberlite and ore stockpiles. Materials tested included field samples of volcaniclastic and pyroclastic kimberlite, processed kimberlite (i.e., kimberlite ore which had been screened and washed as part of the processing procedure), and sedimentary mudstone (a minor xenolithic unit which was assimilated during kimberlite emplacement). Approximately 200 samples of kimberlite materials were collected as part of the geochemistry program. Test-work included whole-rock chemical analyses, acidbase accounting, kinetic leach tests using columns, and mineralogical analyses. Diavik kimberlite has major oxide and trace-element concentrations consistent with global averages for kimberlite. The mean total-sulfur content of the kimberlite material is 0.22 wt% S, but with a significant range. The kimberlite has an excess of carbonate minerals over sulfide minerals (average CO2 = 4 wt%, present mainly as calcite), and has a mean neutralization potential of 311 kg CaCO3 equivalent/tonne. A reactive form of framboidal pyrite associated specifically with the mudstone xenoliths is the primary source of sulfide-sulfur. Long-term kinetic tests confirmed the preliminary interpretations that were made from the static-test results. Kimberlite and processed kimberlite are net acid-consuming materials that produce alkaline drainages and have low but detectable leaching rates for SO4 and specific trace metals such as Al, Co, Cu, Ni, and Zn. If segregated from the kimberlite, mudstone xenoliths are acid-generating (pH = 3) and produce an effluent with elevated concentrations of SO4, Fe, Al, Cu, Ni, and Zn. The study demonstrates that xenolithic units in Diavik kimberlites have an important effect on the environmental geochemistry of the ore rock. The mineralogy and aqueous geochemistry of the kimberlite materials are such that they may not be suitable for general earthworks or as an alkaline agent and should report to an engineered facility to protect site water quality."

Jan 1, 2001

By A. Ignatieff

"THE WORLD'S coal resources represent the largest component of non-renewable energy resources. Coal is now regaining Its position following a temporary decline, particularly in North America during a period of about a quarter of a century. This period provided the opportunity to improve both surface and underground mechanization, thereby increasing the productivity and improving conditions for humans in the mines. Similarly, in preparation, improved cleaning of coal from various impurities including sulphur was achieved, to meet the more demanding requirements for coking coal. Progress was also made in combustion, particularly related to the reduction of pollution. Canada participated in most of these developments, despite the country's strong commitment of the use of hydrocarbons during this period. _Bearing in mind the vastness of this land (3.85 million sq. miles) by comparison with countries like U.S.A., U.S.S.R., and China, Canada's coal resources estimated to date are not large and they are scattered. The original evaluation of 1913 estimated the ""reserves"" from seams over one foot in thickness and a limiting depth of 4,000 ft at 1.2 trillion metric tons. D:. ~.R. MacKay, in his evaluation for the 1946 Royal Commission on the coal industry, known as the Carroll Commission, reduced the ""reserves"" to 99 billion short tons. The increased knowledge now available would indicate that the 1913 estimated was too liberal and the 1946 estimate too conservative but both were closer to a resource than to a reserve designation. Some adjustments of Dr. MacKay's estimates were made in 1970 by B.A. Latour of the Geological Survey of Canada and L.P. Chrismas of Energy, Mines and Resources Canada (EMR). In the last decade the Alberta Energy Resources Conservation Board has developed its own methods of evaluating coal resources and reserves. A methodical approach of exploration and evaluation was carried out by Saskatchewan jointly with the federal government of the lignite resources of Southern Saskatchewan. A similar joint program is in progress in Nova Scotia. Meanwhile, the industry itself carried on an extensive exploration program on the outcrops of promising projects in the Inner Foothills belt of Alberta and British Columbia in preparation for surface mining on a very large scale, with some development of hydraulic mines. All these activities have been reflected in the increase of the country's resources and reserves, which now fortunately are separately defined. In 1979 EMR issued Report E.R. 79/9(1>; the data were developed in 1978 and provided to the World Energy Conference Organization<2>. In 1980 the World Coal Study (Wocol), an international group that included Canada carried out a study which updated the W.E.C. data, indicating some reduction of the 1978 figures; quantities were reported in million metric tons of coal equivalent (C.E.)*(Jl."

Jan 1, 1985

By O. Lashkari

Manipulation of pouring temperature is an efficient way to produce different microstructural features. In order to characterize the microstructure of rheocast billets due to different superheats of 615-695 °C, the parallel plate compression method was employed. Foundry 356 Al-Si alloy with different morphologies of primary a-Al particles were tested at different initial pressures of 4,8, 11,2 KPa, The resulted strain-time graphs were further treated mathematically to calculate viscosity of SSM billets. The interrelationships of viscosity, the microstructure and primary phase flow during compression are discussed, It is shown that the dendritic primary a-Al structure has the highest viscosity number which is almost three orders of magnitude greater than those for globular morphology, The current research have, for the first time, shown the validity and reliability of "parallel plate compression viscometry" method in characterizing microstructural evolution of Rheocast SSM billets.

Jan 1, 2005

By M. Nakai, G. Itoh, R. Yamada, A. Kurumada

In order elucidate the mechanism for poorer fatigue properties of 7000 series aluminum alloys than those of 2000 series alloys, the effect of the test environment on the fatigue crack growth of the two series alloys was investigated, considering the relationship to hydrogen embrittlement. Two 7075-type and four 2024-type alloys were T6-tempered and T4-tempered respectively, and subjected to fatigue crack growth tests in moist and dry environments. When tested in moist air, fraction of intergranular crack path was higher in the 7075-type alloy with coarse equi-axed grains than in the 2024-type alloy with similar microstructure. This was in accord with the larger crack growth rate in the 7075-type alloy. Both the intergranular crack path fraction and the crack growth rate were decreased by changing the environment to the flow of nitrogen gas. Thus, the large fatigue crack growth rate of the 7075-type alloy is attributable to hydrogen embrittlement.

Jan 1, 2015

By S. Kelebek

Efficient separation of minerals is the essence of mineral processing. Separation of hexagonal pyrrhotite in processing of Ni-Cu sulphide ores was investigated together with particle size effects with respect to selective flotation recovery of pentlandite and nickel. The recovery by size response was compared for sodium metabisulphite (SMBS), triethylenetetramine (TETA) and their combinations with amyl xanthate as a collector. The pyrrhotite recovery for all sizes was lower than that of pentlandite for the blank case as well as individual cases with SMBS and TETA. For pyrrhotite, the recovery by size relations in the case of individual uses of reagents were mainly determined by recovery losses at coarser size range (>74 um), which occurs at a coarser size for pentlandite (>212 um). The combined use of SMBS and TETA, and the associated synergistic effect very significantly knocked down the pyrrhotite recovery to less than 7% that was a maximum for the –10 um (attributable to hydraulic entrainment). High recovery of pentlandite in a wide range of intermediate sizes and drastically low recovery of pyrrhotite resulted in a very efficient separation of pentlandite from pyrrhotite in all sizes. Separation of this mineral is discussed in relation to fundamental functionality of the reagents used.

Jan 1, 2017

By N. Birbilis, S. Kairy, C. R. Hutchinson, D. Jiang, D. R. Feenstra, O. Gharbi

"Recent developments in metal-based additive manufacturing (AM) technology have generated considerable interest in multiple industries, owing to flexibility in design and the ability to produce final components in their net shape. The AM of high-strength aluminium alloys has not been widely explored, due to findings of undesirable microstructures leading to short fatigue life and poor fracture toughness; restricting the application of AM to lower strength aluminium alloys (with cast-like Al-alloy compositions) to date. Herein, aluminium alloy AA2024 (Al-3.6Cu-1.2Mg) was additively manufactured via selective laser melting (SLM), with the resultant microstructures and corrosion properties characterised and compared to wrought AA2024-T3. Microstructural characterisation was carried out using transmission electron microscopy (TEM), revealing SLM produced AA2024 included a population of ?-phase (Al2Cu) in preference to S-phase (Al2CuMg) typical of wrought AA2024. Additionally, the corrosion properties were investigated by potentiodynamic polarisation in a range of NaCl concentrations, whilst elemental corrosion rates were also determined (including for open circuit exposure conditions) and quantified in situ with an inductively coupled plasma mass spectrometer coupled with an electrochemical flow cell. Results revealed a significant improvement in the corrosion resistance, and elemental dissolution of AM prepared 2024 relative to wrought AA2024-T3.INTRODUCTION Aluminium alloys remain the preferred candidate materials in applications requiring a balance of low density and strength. The ability to produce net shape components from aluminium alloys has accelerated due to recent developments in metal-based additive manufacturing (AM) technology, including selective laser melting (SLM) and powder bed 3D printing. The AM of Al-alloys, including Al-Si-Mg (namely AlSi10Mg), has become widespread commercially in recent years. Alloys including AlSi10Mg offer reliable and reproducible production by AM, however such alloys (and variants thereof) are not high strength alloys. The pursuit of higher strength AM Al-alloys presents significant merit to multiple industries; however, such higher strength AM Al-alloys have not been widely studied to date. The solidification of high strength Al-alloys during conventional (casting) operations needs to be executed in a manner that avoids so-called =hot-tearing‘, which can arise as a result of the solute type and loading. A report on the solidification of a high strength Al-alloy prepared by AM, along with factors related to solidification, was recently covered by Pollock and co-workers (Martin et al., 2017). It was reported that AM of high-strength aluminium alloys (which have to date been principally based on the compositions of wrought high strength Al-alloys) may lead to undesirable microstructures that reduce fatigue life and result in poor fracture toughness; presently limiting the application of AM to lower strength aluminium alloys (with cast-like Al-alloy compositions) to date."

Jan 1, 2018

By J. D. Robertson

An in situ water sampling device has been developed to measure biologically-available or “labile” metals in natural waters and effluents. The active mechanism involves the use of a polyacrylamide gel layer to quantitatively control metal transfer to a trace-metal-adsorbing, gel-imbedded resin. Because the resin only adsorbs free metal ions (the gel sampler methodology is a kinetic speciation technique), and because metal bioavailability is related to the free-ion activity, the device provides a direct measure of the biological-availability of metals in the environment sampled. The prototype consists of a layer of ion-permeable polyacrylamide gel which separates the solution to be sampled from an ion exchange resin. Because approximately 90% of the polyacrylamide gel is water, mass transport through the gel is diffusion-controlled, and is therefore well defined. Metal ions are rapidly bound by the resin, creating a steep concentration gradient in the gel. The amount of labile trace metal that accumulates on the resin can be related directly to the concentration of the metal in solution, the exposure time and the molecular diffusion coefficient of the labile species. In addition, the passive nature of this device affords it the potential to address many of the limitations presented by conventional sampling methods, such as sample contamination introduced during collection or filtration and changes in trace metal speciation prior to analysis. Laboratory studies and limited field trials indicate that the sampler behaves as anticipated and illustrate that biologically- available metal concentrations in many environments are a small fraction of the total concentrations and often significantly less than the dissolved concentration. The implications of this on regulatory criteria are discussed. Additional field trials and correlation with bioassays are currently underway.

Jan 1, 2000