Search Documents

By M. S. Badollet, W. C. Streib

"AbstractA commercial method .has been developed for controlling the texture of chrysotile asbestos fibers so that they may possess properties comparable with natural sem1-harsh fibers for use in wet •processes.The physical properties of the soft, silky and slimy fibers are partially altered by a flash-heating process which removes a portion of the molecular water.The heat-treated fibers show an improvement in filterability, an increase in bulk, absorption, and surface area and better electrical properties, such as volume resistivity.IntroductionCHRYSOTILE ASBESTOS fibers are found in nature having varying degrees of texture, referred to as soft, semi-harsh, and harsh. Fibers of each type of texture have inherent characteristics which directly affect their usefulness to industry. Visual differences are apparent under a microscope where it is seen that the soft-textured fibers have a silky, serpentine or wavy appearance, whereas the harsh-textured fibers are coarser and spicular. Semi-harsh fibers, of course, have properties intermediate between these extremes.Fankuchen and Schneider ( l) have shown by the use of low-angle X-ray scattering that the diameter of the harsh type of chrysotile fiber is somewhat greater than tha of the soft variety. Surface area measurements on various chrysotiles of different textures tend to confirm their findings. By nitrogen adsorption methods, it was found that the surface areas of soft types of chrysotile asbestos are approximately 23M2 / g whereas for the harsh types they are as low as 11M2/g."

Jan 1, 1955

By T. Prietl

Metallurgical vessel linings are multilayered, consisting of refractory bodies, insulation materials, joints, and additional space to control for thermal expansion. A unique biaxial hot testing press (BHTP) was installed at the RHI Refractories Technology Center Leoben, Austria to enable the three-dimensional behaviour of complex vessel lining segments to be investigated under simulated service conditions. Using the BHTP, the heat up and thermo-mechanical behaviour of magnesia chromite brick lining segments with and without mortar filled joints were examined. The results obtained during the initial heat up provided validation of CFD modelling of the lining system. In addition, after the heat up and under steady state conditions, the lining behaviour during deformation-controlled compression and relaxation was examined. These analyses generated important data regarding the stiffness, joint compressibility, and brick damage of the lining segments after cyclic loading and unloading as well as the benefits of using mortar joints in the lining. These investigations were performed in collaboration with the Christian Doppler Laboratory for Secondary Metallurgy of Nonferrous Metals, University of Leoben, Austria. The BHTP has been operational since November 2004 and is providing information regarding the thermo-mechanical behaviour of different lining segments.

Jan 1, 2007

By S. Mao

Total station has been predominantly applied in stationary survey scenarios in construction. With the moving target tracking and point survey automation functions, a robotic total station (RTS) lends itself well to more dynamic applications. Nevertheless, a RTS unit is still unable to track multiple targets simultaneously or to survey a target point when the line-of-sight is temporarily unavailable. In this paper, we propose a methodology to synchronize and automate multiple RTS units intended to address dynamic tracking and surveying applications in the construction field. By using the application programming interface (API) from the manufacturer, we implement the proposed methodology and the prototype system integrates two RTS units in regard to space and time and communicates survey command instructions among RTS units through wireless networks. The two RTS units can be operated to survey the two ends of one swinging sling concurrently in order to retrieve the actual length of the sling within several millimeters accuracy. Besides, in applications where line-of-sight between a target object and one RTS unit cannot be guaranteed all the time, continuous surveying can be materialized by automatically delegating the task to another synchronized RTS unit with clear view of the target object. A field test was conducted to demonstrate the application of the proposed automation approach in which sling length was measured of a rigging framework used for lifting industrial modules. The testing results are presented and achievable accuracy and reliability are discussed. The proposed solution overcomes the limitations of global positioning system (GPS) and laser scanning and holds high potential to provide cost effective solutions to many dynamic field applications.

Aug 1, 2013

By Lachezar Tsotsorkov

Being a mining company, Assarel-Medet has a significant impact upon the environmental components. In order to meet the legal requirements and the requirements stipulated by the effective permits as well as to reduce the environmental imprint throughout the years, the policy of the company to implement a number of projects to improve the environmental components quality and the environmental state in the company?s region. The projects associated with atmospheric air quality management and reduction of the impact exercised by Assarel-Medet JSC by implementing various measures to eliminate the potential sources of the impact, preventive and rehabilitation initiatives as well as organizational and administrative activities are among the most important ones. A stable improvement of atmospheric air quality in the region and minimization of the company impact upon the ground air state in the region was observed in the period from 2005 to 2012 due to the applied measures. This project is a contribution to the environmental protection, in particular to atmospheric air protection, by applying integral monitoring and modeling methods to identify the negative impact by the mining companies and plan measures to reduce and restrict it as well as to improve the quality of the environment and living area of people working and living in the impact range as an element of sustainable development.

Aug 1, 2013

By W. C. Whittaker

COMPLETED in November, 1943, at a cost of over $1,500,000, Elk River colliery of the Crow's Nest Pass Coal Company, Limited, has been laid out and equipped for an ultimate annual production of 1,000,000 tons and replaces the recently closed Coal Creek plant, which has been operated by the Company for the past forty-five years. The project has involved the opening of mines in three seams, the construction of a complete set of colliery buildings, including a modern preparation plant of 360 tons per hour capacity, and the laying out of the necessary yard tracks and spur connecting the new development with the Company-owned Morrissey, Fernie and Michel railway, which, in turn, connects with the Canadian Pacific railway at Fernie. The colliery is three and a half miles east of Fernie, B.C., near the southern end of the Crow's Nest coal field, which contains the largest and most important body of coal in the Province of British Columbia. The coal-bearing horizon is the Kootenay formation, present in the form of a syncline covering an area of 230 square miles. Most of the coal seams occur in the lower 2,000 feet of the formation, the covering beds being largely coarse sandstones and conglomerates of great thickness, the presence of which accounts largely for the preservation of the coal measures. James McEvoy, in the report of the Geological Survey of Canada for the year 1900, states that the basin appears to contain a fairly constant coal content of nearly 172 feet in 23 seams of a thickness of one foot or over. Coal has been mined in the Fernie district since 1897 and the first shipments were made from Coal Creek colliery in the following year, over the then newly constructed British Columbia Southern railway. Since that time, a total of over 16,000,000 tons of coal has been produced, an average of 350,000 tons per year. The7ears of peak production were 1910, 1912, and 1913, with an all-time high of 924,000 tons in 1913. The lowest output in the history of Coal Creek was that for the year 1933, when only 60,340 tons were produced, the colliery being closed for some months. Present production from Elk River colliery averages 1,150 tons per day, the output being considerably less than it could be were sufficient man-power available.

Jan 1, 1944

By Charles G. Kemsley

MR. C. R. WHITTEMORE: It is interesting to note that the mining industry is making increased use of alloy steels for drilling. They will undoubtedly lead to greater footage at lesser cost. Mr. Kemsley states that, for use in hard ground, the shanks are brought to a hardness of 435 to 440 Brinell by heating them to approximately l,800°F. It seems to me that this temperature is excessively high-it is considerably above the critical point of the steel. The only effect of such a high temperature is to lessen considerably the impact resistance of the steel. The possibilities of an oil quench, followed by a tempering draw which does not lessen the hardness of the steel too much but increases its toughness, might well repay further study; also the temperature control, a factor which depends on the composition of the steel. However, service results are undoubtedly the best criterion of practice. MR. KEMSLEY: I would like to point out that the steel is not quenched at 1,800°F. After heating to this temperature, it is laid aside to cool gradually; this high temperature is necessary to produce the required hardness by simple normalizing-cooling in still air. We all know that ideal conditions for hardening steel demand salt baths and furnaces with automatic temperature control, but for most companies the cost of such equipment having sufficient output capacity is prohibitive. The end we are trying to attain is to make good drills at a cost that will be within the means of any mine.

Jan 1, 1942

By Mehmet Guney

This article is based on a detailed heat investigation conducted at the Rokana Division of Nchanga Consolidated Copper Mines Limited while both authors were employed in Zambia. Mindola Mine is one of the three underground mines comprising the Rokana Division on the Copperbelt of Zambia, producing about 270,000 tons of ore per month at 1.9% Cu and 0.14% Co. The total volume of air being circulated by means of five primary fan installations slightly exceeds 1,000 m3/sec at standard density. Sectional bulk cooling is practised where air cooling coils are installed at primary splits some considerable distance from the stoping operations. Total capacity of the refrigeration complex is 10,500 kw (3,500 R. tons), of which about 7,000 kw is available as effective cooling power after losses, but the heat removed from the coifs is about 3,500 kw with 61% over-all plant performance. An extension program is planned for a further five production levels with the re-deepening of a sub-vertical shaft. Thermal heat will become a major problem at increased depth associated with higher rock temperature, higher thermal conductivity of the rock groups encountered and fissure water flowing into working areas through the strata with increased rock temperature. This paper describes the ventilation and refrigeration practices in Mindola Mine, with special reference to future thermal heat problems. These are discussed with a view to mining at depth.

Jan 1, 1979

By G. J. Heferen, A. Pranowo, N. J. Aslin, P. O. Eriksson

Glencore Technology (GT) has over four decades experience supplying stainless steel cathode plates (“cathode plates”) to the electro-refining and electro-winning industry. Cathode plates are typically the single biggest capital investment in a refinery. Refineries may view cathode plates as fixed asset or consumables depending on their operational characteristics. This paper examines the issue of cathode plate life and the strategies and philosophies used by different plants in the management of their cathode plate asset. Some plants operate with their original plates after more than 20 years. Others accept high turnover and regular maintenance as normal operating practice. Reference data are provided on plate life for various operating plants including benchmark plants achieving best-practice plate life and operating cost. The role of the electrode handling equipment on cathode plate longevity is also examined, including latest developments in Cathode Stripping Machine, robotic copper stripping, and full-automation production cranes. The ability to identify and manage the population of plates in service is also critical for maximising plate life and minimising its overall operating cost. This paper discusses a novel and unique RFID system for tracking and managing cathode plate inventory. INTRODUCTION Permanent cathode plates The adoption of permanent stainless steel cathode electrodes in the electro-refining of copper was the most significant process development since the first commercial electro-refineries were built in the late 19th century. It provided significant improvement over the labour intensive and complicated starter sheet system. Copper grows over the permanent cathode blade for a number of days before being stripped, and the permanent cathode can be returned straight back to cells for the next cathode cycle. Glencore Technology (formerly Mount Isa Mines (MIM), then Xstrata Technology) has been manufacturing permanent stainless steel cathode plates from the late 1970s with the birth of ISA PROCESS™, and the Kidd process that came one decade later. Invented and commercialised by Mount Isa Mines, the ISA PROCESS™ was first implemented into Copper Refineries Limited (CRL), Townsville, in 1978. The KIDD PROCESS by Falconbridge evolved in the 1980s and was first implemented into the Kidd Creek Tankhouse, both operations converting from traditional copper starter sheets.

Jan 1, 2019

By C. G. Williams

IN preparing this paper on Canadian mine taxation, there has been no attempt to detail the requirements of the various taxing bodies; but rather to consider the matter from the standpoint of its underlying principles and give a general idea of the methods adopted. I have added an Appendix setting forth the principal features of the various Acts, which should be used for general reference only, since new rulings alter minor details from time to time. In current legislation, many important points are left to the discretion of the Ministers and their deputies. We are, indeed, fortunate in having in Canada an able and conscientious body of permanent officials, who bring a sense of justice and courtesy to their work which is most commendable, and which has done much to simplify the working out of general problems. The production of metals may rightly be deemed a form of manufacture, but differs from the average manufacturing business in three important respects: (1) In its early stages, it is wholly speculative, since it is impossible to make any definite appraisal of value or possibilities. (2) The principal asset of any mine, i.e., the ore in the ground, is a wasting asset, and is irreplaceable. (3) Any additional burden by way of taxation cannot be passed on to the public but must be borne entirely by the producer. Having regard to the first of these differences, it is apparent that, since the risk of loss is great, the reward in case of success must be correspondingly great. This fact seems to be constantly overlooked by those who regard the all too few outstanding successes in Canadian mining history as fit prey for predatory legislation. As an illustration of the speculative nature of early mining development, let us consider the Province of Ontario-and I take this illustration simply because I am more familiar with conditions there, and not because I believe it differs greatly from any other province. From 1907 to 1933, 165,243 claims were staked and recorded, from which 43 mines were developed which paid one or more dividends. There was, of course, some duplication through re-staking; also, on some claims very little work was done, and most mines have more than one claim. But, since staking and recording cost real money and effort, each of these claims must have been considered to have had merit.

Jan 1, 1935

Although Canadian bentonite is competitive in quality for most uses, it has not been accepted for the pelletizing of iron ore concentrates. In 1962, Canada consumed about 10,000 tons of imported bentonite for this use. By the end of 1965, the planned domestic consumption for this purpose alone will probably be more than 100,000 tons a year, valued at about $3 million. Consequently, a challenge exists for the establishment of a Canadian source of high-quality bentonite for pelletizing. Such a bentonite would also be suitable for the two other major applications -well drilling and foundry use. Brief mention is made of such topics as the identification, 1noperties, occurrences, exploration, applications, technology and laboratory testing of this clay. In particular, the type of bentonite in demand, the geological horizons warranting exploration, and simple preliminary test methods are discussed.

Jan 1, 1964

By F. Chachula, A. Molinaro

"Sulphide mineral flotation operations continuously strive for a balance between mineralogy, mineral liberation, circuit conditions and reagent solutions to maximize the production rate and recovery of payable metals. The Taseko Gibraltar copper – molybdenum mill operations underwent an extensive project focusing on the fundamentals to identify the effects of process conditions and mineral liberation to improve the bulk circuit copper – molybdenum recovery efficiencies in the bulk flotation circuits. This discussion will provide process data that demonstrates; 1) fundamental relationship between mineral liberation to recovery and grade, 2) flotation circuit condition testing and optimization, 3) reagent combinations resulting in efficient/economical mineral recovery, and 4) the development of a xanthate free reagent solution. The data presented and discussed will also touch on flotation parameters including pH, retention time, kinetics and the effect on bulk circuit recovery performance.INTRODUCTION Taseko's is the owner (75%) and operator of the Gibraltar copper-molybdenum mine, located in south-central British Columbia, the second largest open pit copper mine in Canada and the largest employer in the Cariboo region. Taseko restarted Gibraltar in 2004. From 2006 until 2012, the company invested ~$700 million to expand and modernize the operation which was originally scheduled for demolition when the company acquired it in 1999. In the spring of 2011, construction commenced for Gibraltar Development Plan 3 (GDP3). GDP3 included the construction of a standalone 30,000 ton per day concentrator, built adjacent to the existing 55,000 ton per day facility. The new design capacity of Gibraltar was designed to be 85,000 tons per day. An integral part of the project was a new molybdenum recovery facility. In addition to the new concentrator, the mining fleet was upgraded with a new mining shovel, production drill and ten haul trucks (Taseko, May 2015). In May of 2015, the Company completed an updated mine plan for Gibraltar featuring a 50% decrease in strip ratio. This new mine plan was a result of a detailed, six-month engineering study and forms the basis of an updated NI 43-101 compliant reserve (Taseko Announces Improved Economics At Its Gibraltar Copper Mine, 2015). The new mine plan took into account lower milling costs as a result of the modernized processing facilities (Taseko, May 2015)."

Jan 1, 2018

By F. Mercier-Langevin

ABSTRACT; Agnico-Eagle’s LaRonde mine is one of the deepest mines in Canada. Ground conditions in the deeper levels can be very challenging, ranging from hard and brittle to soft and squeezing. As a result, rock mechanics and ground control practices have had to evolve considerably to accommodate progressively deeper mining activities. This paper focuses on the deeper levels of mines and how the difficult ground conditions encountered there have influenced the mining strategy. The first section examines ground control practices and support systems in highly stressed, poor quality rock. The evolution of level layout is also presented. Finally, improvements in stope sequencing are reviewed.

Jan 1, 2010

By D. K. Sarkar, J. Perron, J. D. Brassard

"Nearly perfect spherical shaped water drops rolling-off from the surface of lotus leaf is one of the beauties of nature. This kind of surface is called superhydrophobic, since the water does not like it. Physically, a superhydrophobic surface provides a contact angle (CA) of water over 150°. The combinations of both mico-nanostructure topography as well as low surface energy are essential to have such high CA on a surface. Nano-micro structured superhydrophobic surfaces have been developed in different methods. (i) Monodispersed fluorinated silica nanoparticles have been synthetized via Stöber Sol-Gel process and deposited on various surfaces, such as aluminium or glass, to obtain transparent superhydrophobic thin films. (ii) Similarly, zinc stearate nanocomposite coating has been fabricated by spray process on the same substrates. These thin films are found mechanically robust with drag reduction of coefficient 16% lower than as-received surfaces. (iii) By electrodepositing pure zinc on steel surfaces and further coating it with diluted room-temperature vulcanized silicone rubber, the surface become superhydrophobic. This superhydrophobic surface protects the steel against corrosion by increasing the polarization resistance from 1.5 k? on steel to 44.4 k?. This coating also reduced the ice adhesion on the steel surface 6.3 times as compared to bare steel substrates. Globally, these superhydrophobic surfaces have tremendous applications against corrosion reductions, drag reductions and ice adhesion reductions.INTRODUCTIONSuperhydrophobic coatings are increasingly attractive to the industry and academia due to their unique self-cleaning properties as a result of their water repelling characteristics. Fabrication of superhydrophobic coating is an inspiration from nature as water is seen to repel on many natural surfaces such as those of the lotus leaves, butterfly wings, water striders’ legs, and so on (Gao & Jiang, 2004; J. Huang, Wang & Wang, 2006; Neinhuis & Barthlott, 1997; Zheng, Gao & Jiang, 2007). This non-wetting phenomenon is well understood on lotus leaves, shown on the Figure 1 (a), and it is considered as the basis of the studies of superhydrophobicity. The existence of this binary structure on the surface of the lotus leaves allows a large amount of air entrapment and consequently reduces the contact area of water on it and the presence of low surface energy waxy components with reduced affinity to water together leads to the superhydrophobic properties. The phenomenon is shown on Figure 1 (b). Cassie and Baxter (Cassie & Baxter, 1944) as well as Wenzel (Wenzel, 1936) proposed two mathematical models to explain the wetting phenomena on rough surfaces that leads to superhydrophobic properties. By definition, superhydrophobic surfaces are characterized by a water contact angle value = 150° with the rolling off of water drops from the surfaces (Sarkar & Saleema, 2010). Superhydrophobic surfaces find tremendous importance in the technological world where it can applied in domains such as anti-corrosion, anti-biofouling, electrowetting, icephobic and even in drag reductions (Bushnell & Moore, 1991; Cao, Jones, Sikka, Wu & Gao, 2009; Carlborg & van der Wijngaart, 2010; Carré & Mittal, 2009; Y. Huang, Sarkar & Chen, 2010a; R. Karmouch, Coude, Abel & Ross, 2009). However, the most important challenge faced by industries is their feasibility large scale in an effective an economical manner."

Jan 1, 2016

By A. H. Anderson

THE travelling grate coking process was developed by Shawinigan Chemicals, Limited, at their Shawinigan Falls plant. The first production unit went into operation a month prior to the outbreak of the war. Since then a substantial part of the coke used in the manufacture of calcium carbide has been produced by this process. In the following will be given a short account of the development work, a description of the process and the equipment, a discussion of the properties of the coke, the economics of the process and its future possibilities. EXPERIMENTAL WORK The carbide industry is a large consumer of coke, one ton of commercial carbide requiring for its production 1,200 lb. This coke must meet certain specifications in order to be acceptable. It should have a low ash content, preferably below 8 per cent, and the sulphur and phosphorus content must not be above specified limits. The size of the coke is also important. If it is too large it has to be crushed before it can be used in the furnaces, and if it is too fine it may have to be screened and briquetted. In addition, it must be dry. Although it was generally possible to purchase coke, including petroleum coke, and coke fines, in the quantities required, it became increasingly more difficult as time went on to obtain coke of a suitable quality at an attractive price. It was therefore natural for us to look to coal carbonization as a means of basing the supply of the fundamental raw material for carbide manufacture on something more solid than the shifting conditions of the coke market.

Jan 1, 1944

By A. L. Mular

"IntroductionSince the mid -1960s, automatic control of grinding circuits has become the rule, to avoid losses attributable to frequent circuit upsets associated with uncontrolled disturbances such as ore hardness variations. Higher capital costs of grinding equipment and corresponding operating costs-especially with respect to energy consumption-are major factors that continue to stimulate interest in grinding control.Grinding circuit control strategies depend upon the control objectives defined by the processing plant and are subject to constraints such as: maintain final per cent solids within some range, do not transport steel ball s out of the discharge trunnion, or do not overflow or empty the pump box and so on. Constraints depend on the nature of equipment employed within the grinding circuit and may actually determine the characteristics of the control scheme. Typical control objectives are:1. Maintain final particle size at set point by ,a. manipulation of fresh feed rate with circulating load maintained by manipulation of pump box water addition rate, orb. manipulation of pump box water addition rate with circulating load maintained by manipulation of fresh feed rate, where the methodology utilized to accomplish either (a) or (b) is dependent upon equipment/circuit constraints such as the availability of a variable speed pump.2. Maintain circuit throughput at a maximum by,a. manipulation of fresh feed rate subject to constraints on final particle size and variables such as power draw, circulating load and mill overload.3. Maintain mill load at set point by a. manipulation of fresh feed rate subject to constraints such as on power draw.4. Maintain mill power draw at set point bya . manipulation of fresh feed rate subject to mill load constraints. Often, a grinding control objective is dictated by the recovery vs fineness-of-grind characteristic that exists for downstream separation circuits. When recovery is relatively insensitive to size, maximum throughput in the grinding circuit is advantageous.The purpose of this paper is to review control strategies for primary ball mill grinding circuits, rod mill/ball mill grinding circuits and semi-autogenous grinding mill circuits. Primary sensors employed are highlighted and modern trends are documented briefly."

Jan 1, 1989

By M. Oliazadeh, A. Vazirizadeh

"The inclusion of small amounts of silicon, phosphorus and sulphur in iron ores or concentrates can have a profound effect on the steel making process and thus on the final iron and steel products. In nature however, it is inevitable that iron deposits contain unwanted elements. Each element has its own distinct effect on the final steel product. The effect of high silicon is the formation of gray iron. Phosphorus mainly increases hardness and strength, lowers solidus temperature and increases fluidity and cold shortness. Finally sulphur contamination causes cracks in the iron texture when smelting and forms white iron when casting. Overall, the acceptable level of phosphorus, sulphur and silica in the iron concentrate should be less than 0.04%, 0.15 % and 1.5 % respectively.Scarcity of high grade iron ores necessitates using lower grade ores with higher amounts of impurities. The purpose of iron concentrators is to increase iron grades to an appropriate level suitable for steel making as well as removing impurities. Although many impurities can be traced in the ore, the most predominant impurities are limited to one or two elements. In this paper the beneficiation methods for removing SiO2, P and S are presented, including flotation, and the parameters that need to be considered in the design of beneficiation plants are discussed. Finally industrial cases are discussed along with their metallurgical performance.INTRODUCTIONIn metal sector, value of iron ores and concentrates is determined by iron percentage as well ascontent of:• Useful elements (Mn, Ni, Cr, V, Ti): natural alloying elements in steel• Deleterious impurities (S, P, As, Zn, Pb, K, Na): impair metal properties or complicate operational process in blast furnace• Fluxing components (Si, Ca, Mg,, Al)Sulphur and copper result in red-short, phosphorus is the cause of cold brittleness and arsenic and copper decrease welding characteristics. Sulphur should not exceed 0.15 in commercial ore. Acceptable sulphur content in ores and concentrates for producing sinter and pellets is 0.6%max, as sintering and heat hardening of pellets remove sulphur 60-90%. Phosphorous content in ores, sinter and pellets is limited to 0.07%-0.15%. 0.00.1% As max, 0.1-0.2% Zn max and up to 0.2% Cu are allowed in iron-ore part of the blast furnace burden for the production of standard conversion pig iron. Slag-forming components are divided into basic oxides (Ca, Mg) and acidic (Si, Al). Higher ratios of basic to acidic oxides are preferred since this reduces raw fluxing material."

Jan 1, 2016

By Malcolm R. Gent

"The presence in Saskatchewan of sixteen kimberlite pipes of probable late Albian age has been reported. An abundance of aeromagnetic anomalies possibly attributable to kimberlite pipes have been identified and it is anticipated that industry has acquired reasonable proof of the presence of more than seventy k imberlite pipes in Saskatchewan. Historical reports of diamonds, the discovery of kimberlite pipes and these aeromagnetic anomalies indicate the Phanerozoic Basin and some parts of the exposed Shield in Saskatchewan have an excellent potential f or the occurrence of economically exploitable diamond deposits. The presence of some igneous minerals found in some salt solution breccias also indicates the probable occurrence of extensive diatreme activity during the Devonian.A Laramide Orogeny-induced crustal hinging or arching of the eastern margin of the Phanerozoic Basin and probably dextral wrenching-induced arching and faulting within the basin are proposed as major factors in the emplacement of Cretaceous or younger kimberlites. Zones of crustal weakness between subcratonic Archean blocks and internal faults are also thought to be significant controlling factors in the location of kimberlites in Saskatchewan.Mapped aeromagnetic anomalies interpreted as being possibly due to kimberlite pipes generally tend to be concentrated in, areas underlain by a basement of or with components of Archean age. Within Saskatchewan, these anomalies occur within the probable Trans-Hudson Orogen zone; the Rae-Hearn Craton margin; and the northeast flank of the Elkpoint Basin. Recognized areas of potential f or kimberlite emplacement are the Phanerozoic basin margin, the western limit of the Superior Province adjoining the Churchill Province, and a swath approximately 150m wide along the northeast-southwest trending Shaunavon linear and other areas of inner basin arching."

Jan 1, 1992

By William Petruk

Mineralogical investigations in connection with gold metallurgy are usually performed to find the reason for poor recoveries by cyanidation or by other leaching techniques. Poor recoveries most commonly are obtained when (I) native gold is encapsulated in an insoluble mineral as "invisible gold"; (2) native gold is coated with a precipitate; (3) gold-bearing products are insoluble in cyanide solutions; (4) carbonaceous material in the ore adsorbs gold; and (5) associated minerals decompose and consume cyanide. Samples of refractory material quite often have low gold tenors. It is difficult to find the gold-bearing minerals in such samples with an optical microscope because the probability of finding trace minerals in samples is small. The probability decreases with decreasing grain size of the gold-bearing mineral and with decreas¬ing gold tenor of the sample. Techniques have been developed to increase the success rate of finding gold grains; some are (1) concentrating heavy minerals; (2) preparing special polished sections; (3) searching with an image analyzer; and (4) dissolving associate silicate and sulphide minerals.

Jan 1, 1989

By E. Bonsall, J. J. Brummer, A. R. Graham

"A method and device are described for sampling diamond-drill core by cutting a continuous fillet of constant cross section from the cylindrical surface of the core throughout appropriate sample lengths. The apparatus employs a tapered, abrasive-set, cutting wheel, the conical cutting surface of which projects slightly into a rectangular core-guiding trough set parallel to the axis of rotation. The depth of fillet and thus the amount of sample per unit length can be regulated by adjusting the core guides. The freshly cut fillet itself, by engaging in a guide beyond the cutting wheel, acts to prevent rotation of the core during operation of the device.The cuttings which form the sample are normally collected in a tray below the cutting-wheel and appear at about 80 per cent -100 mesh. They require little or no further treatment or comminution before analysis. Speed, economy and convenience of sampling are thus greatly increased as compared with conventional sampling by im-1>act breaking or sawing, followed by crushing, grinding and sub division for assayAssays from fillets (about 1/20 the cross-sectional area of the core) and from 180-degree segments, from the same ninety-three core-samples, representing 431 feet of nickel-copper mineralization, gave the following results:"

Jan 1, 1968

By I. C. Edwards, E. O. Lilge, H. H. Mccreedy

"Introductory and GeneralTHE DRIESSEN CONE bas been used fairly extensively commercially as a classifier. Its use as a concentrator in the upgrading of ores at a fairly high ratio of concentration with concomitant recoveries has been almost negligible. Certain known features about the cone, however, such as its high throughput capacity, cheapness of construction and operation, and simplicity of design have attracted the attention of mill men. An inadequate knowledge of the operating characteristics of the cone when used as a concentrator seems to have been the main reason for its lack of use. It was for this reason that the present investigations§ were undertaken to determine the operating characteristics of the cone and its application to the concentration of uranium ores, with particular emphasis being placed on the concentration of low-grade uranium ores.The investigations were started in December, 1951, and have continued uninterrupted to the present. The initial work was confined chiefly to investigating the operating characteristics of the cone in order to establish the trends that certain variables would exert on the general metallurgy of uranium concentration. Optimum metallurgy was therefore not the prime initial objective."

Jan 1, 1955