Search Documents

By W. A. Bain

"AbstractProduction from the Excelsior Reservoir has amounted to approximately one million barrels. This production has caused a 'Pressure •drop of 10 p.s.i. from the original pressure of 1,245 p.s.i.g. Volumetric balance calculations indicate that the pool as being produced by a water drive whose strength is •probably unsurpassed in Western Canada. It has also been shown by 'unsteady state' calculations that the reservoir will still be above the saturation pressure of 915 p.s.i.g. at the time of depletion. The average permeability of the producing formation is approximately 1,000 millidarcys and, consequently, well draw-downs are very low. The field is essentially a bottom-water drive and calculations have shown that gravity drainage will greatly assist the recovery of oil. Water flooding data on several cores •have placed the flushing efficiency at •approximately 50 per cent, which indicates a recoverable oil-in-place of 17.7 million stock tank barrels. Calculations and field data indicate that the MER for the early life of this field is probably as high as 8,000 to 10,000 stock tank barrels per day.IntroductionTHE EXCELSIOR NISKU oil reservoir is located about twenty miles northeast of Edmonton. The field was discovered in November, 1949, by Imperial Excelsior N.o.1 well, in Lsd. 13, Sec. 3, Twp. 56, R. 22, W. 4, at a depth of 3,850 feet.Since discovery, development has continued on a 40~acre spacing pattern. At the end of 1951, drilling over approximately 80 per cent of the estimated productive area of 1,680 acres had established 32 we1ls capable •of production. The field •has been fairly well delineated by dry holes on all but the eastern flank ."

Jan 1, 1952

By A. McLean, X. Men

"With high quality sulphide ores diminishing, nickel production from low-grade oxide ores becomes increasingly important and a major concern is the high sulphur level in the resultant ferro-alloy. So, desulphurization of the ferronickel becomes an important consideration. Red mud is a waste product of alumina industry and causes adverse effects on environment. In the present study, experiments were conducted to determine feasibility of using red mud as a major ingredient of refining fluxes for ferronickel desulphurization. In view of their influence on slag-metal separation, contact angle measurements between ferronickel alloy and molten slag made from red mud were also determined. INTRODUCTIONNickel is a very important metal that finds a variety of applications including consumer products, building, automotive and electronics. There are two kinds of ores containing nickel, namely oxide and sulphide ores. Anthony and Flett [1] reported that about 55% of the world’s nickel production originates from sulphide ores while the balance of new nickel is derived from oxide ores. However, oxide ores count for about 70% of the worldwide reserves. Apparently, oxide ores will play a significant role in the production of nickel in the future. Most of nickel produced using oxide ores is from pyrometallurgical processes namely ferronickel smelting or matte smelting. So, we can draw such a conclusion that using nickel oxide ores to produce ferronickel will become more and more important .Before used to make stainless steel or other materials, the ferronickel need pretreatment to remove impurities especially sulphur and phosphorus that will cause negative influence on the properties of steel product. Red mud is a by-product during alumina production. Usually, about 1 to 1.5 tons of red mud will be produced when we get 1 ton of alumina. About 90 million tones of red mud are produced every year in the world [2].Red mud is deemed as a toxic industrial waste which needs treatment before discharge because of alkalinity and chemical and mineralogical properties. Until now, the main means to deal with red mud are to store it in impoundments or dump it in the sea depending on local environment. Nowadays, how to recycle red mud has become a pretty hot topic around the world. The last 40 years have witnessed a lot of patent applications concerning the ways of red mud utilization. However, a little amount of red mud is consumed until now due to the limitations of recycling red mud."

Jan 1, 2012

By M. Lebeuf, A. Dumais, C. Farsangi, N. Singh

The Nunavik Nickel project began ramp-up of a new ore body (Expo) in November 2014. This new deposit is significantly more competent than the previous ore type milled (i.e., the plant moved from a feed with a BWI of 12.2 kWh/t to predominantly material with a BWI of 19.6 kWh/t). Despite circuit changes made in advance of the Expo ore ramp-up (grinding media size, mill loading/power draw, and cyclone configuration) the throughput of the plant was bottlenecked at 90% of targeted throughput with multiple stoppages to grind-out the primary mill due to excessive circulating loads. During this time, the secondary milling circuit was under-utilised: therefore the focus for debottlenecking plant production became increasing the product size of primary milling. Given the scope of changes already made to the circuit, it was decided to test the mill in open circuit. The milling changes were modelled using the Molycop Tools package to identify potential problems. In the modelling and plant trial it was apparent that the ball size in the secondary grinding circuit was inadequate, resulting in pebbling. The power draw of the secondary mill was brought up to minimize pebbling and the average ball size was increased. The switch to open circuit primary milling permitted a significant augmentation in plant tonnage. While the overall grinding efficiency decreased using the open circuit configuration, the ability to increase throughput made it the clear operating choice.

Jan 1, 2016

By Alvis L. Lisenbee, Colin J. Paterson, Mustafa M. Hariri

"Abstract-The schist-, sediment-, and intrusion-hosted Tertiary Au-Ag hydrothermal deposits of the northern Black Hills, South Dakota are localized and controlled by various types of fractures. This study is an attempt to distinguish between and discuss the possible causes of these fractures in three mines: Richmond Hill, Annie Creek - Foley Ridge (ACFR), and Gilt Edge.Five models based on the structural and tectonic settings of the northern Black Hills are proposed for the fracture origin. In Richmond Hill mine, mineralized fractures within the schist-hosted deposits are in the form of veinlets and stockworks. Larger veins filling open spaces along schistosity planes are also present. Fractures in Richmond Hill mine are related to breccia pipe emplacement and influenced by the Precambrian foliation.Fractures in sediment-hosted (ACFR) and intrusion-hosted (Gilt Edge) deposits are mode I systematic joints. These fractures, and similar ones examined in seven locations outside the mines, are related mostly to the formation of the Lead-Deadwood dome. Fracture trends vary from one area to another depending on their location with respect to the dome. Other factors, such as the Black Hills uplift, pluton emplacement, and Precambrian foliation, may also affect the fracture trends. The proximity of the mines to domes formed by multiple intrusions, the associated fracture patterns and density, and existence of breccias, may be used in exploration for similar deposits in the northern Black Hills or other areas of similar geologic settings."

Jan 1, 1995

By Alvis L. Lisenbee, Colin J. Paterson, Mustafa M. Hariri

"The schist-, sediment-, and intrusion-hosted Tertiary Au-Ag hydrothermal deposits of the northern Black Hills, South Dakota are localized and controlled by various types of fractures. This study is an attempt to distinguish between and discuss the possible causes of these fractures in three mines: Richmond Hill, Annie Creek – Foley Ridge (ACFR), and Gilt Edge.Five models based on the structural and tectonic settings of the northern Black Hills are proposed for the fracture origin. In Richmond Hill mine, mineralized fractures within the schist-hosted deposits are in the form of veinlets and stockworks. Larger veins filling open spaces along schistosity planes are also present. Fractures in Richmond Hill mine are related to breccia pipe emplacement and influenced by the Precambrian foliation.Fractures in sediment-hosted (ACFR) and intrusion-hosted (Gilt Edge) deposits are mode I systematic joints. These fractures, and similar ones examined in seven locations outside the mines, are related mostly to the formation of the Lead-Deadwood dome. Fracture trends vary from one area to another depending on their location with respect to the dome. Other factors, such as the Black Hills uplift, pluton emplacement, and Precambrian foliation, may also affect the fracture trends. The proximity of the mines to domes formed by multiple intrusions, the associated fracture patterns and density, and existence of breccias, may be used in exploration for similar deposits in the northern BlackHills or other areas of similar geologic settings."

Jan 1, 1995

By Tadeusz W. Wlodek

THE known phenomenon that a test-piece of ferro-magnetic steel is magnetic after it has been broken in tension indicates that, while it is being loaded, the steel acquires magnetic properties. In the present investigation of the influence of the stress on the magnetic flux, repeated pulsating stresses of increasing amplitude, varying from zero to the maximum tensile value, i.e., pull-pull loading, were employed. The specimens were prepared from two types of carbon steel and two of alloy steel. The magnitude of the magnetic flux was determined indirectly. The voltage and mode of variation of the electromotive force induced in a coil surrounding the stressed steel specimen were measured as an indication of the varying magnetic flux within the specimen. Curves representing the electromotive force induced by the varying magnetic flux show that as the tensile load increased so also the magnetic flux increased, with a corresponding increase in measured e.m.f. At a certain stress there is a sharp bend in the voltage curve (point Win the diagram, Figure 5); this critical stress corresponds very closely with the yield stress (0.2 per cent permanent strain). Beyond this point, slight increases in the stress produce large increases in the voltage. The wave form of the e.m.f. was registered on an oscillograph. Analysis of the curves so obtained demonstrated the necessity of continuing these experiments, in order to determine the type of induced wave form associated with various types and amplitudes of stresses. In these experiments, the shape of the stress wave was sinusoidal, although the shape of the induced e.m.f. was sinusoidal only up to a certain load and became more and more complex above this load.

Jan 1, 1944

By J. Shanks

A S far back as 1925, Brazeau Collieries, Limited, became interested in .briquetting. This was brought about by complaints from their principal customer that stack losses, due to a high percentage of fine coal in their mine run, were excessive. The Company considered oil spraying of the fines. This, after some experiments and tests had been made, was ruled out as uneconomical and impracticable. When sufficient oil to be effective was put into the fines, it caused the coal in the tender of stoker-fired engines t0 arch over the screw feeder. The Company ultimately placed their problem in the hands of the Re-search Department of the University of Alberta. Experimental work was carried on by this department over a period of more than a year. The results obtained and the experience gained in this research work were conveyed to Brazeau Collieries in a report dated October 31st, 1929, and in a supplementary report dated February 2nd, 1935. Most of the results obtained in experimenting with Brazeau coal are embodied in a brochure, reprinted from the proceedings of the Second International Conference on Bituminous Coal, Vol. 19-24-28, entitled Principles in the Briquetting of Coking and Non-Coking Bituminous Coals, by E. Stansfield and W. A. Lang. All who are interested in briquetting should read this brochure. In the writer's opinion, iris the most important treatise on the subject printed in recent years. The results given in the paper are, of course, those obtained in laboratory investigation. It was pointed out to the writer that it would be most interesting to have such results correlated with those obtained in commercial practice. In this short paper, an attempt is made to do so.

Jan 1, 1942

By Farnham. G. S.

It is difficult co know how to deal with this subject before a group having such mixed interests. The mining man is not coo concerned with the problems of alloy research. The engineer is more interested in properties of materials than how these properties can be achieved. The business man feels that scientific history and prognostication are not for him, predicting trends or possible developments in the economic field being a more than sufficient occupation. Yet the application of physical metallurgy research to industry is of importance to miner, engineer, and business man, for only through such application can the continuing existence of industries manufacturing or consuming metals be assured. History shows that hard work does not guarantee industrial survival. For instance, the Bessemer method of steel making superseded puddling operations; it, in its turn, has been largely displaced by open-hearth processing; later, steels made in electric-arc furnaces displaced open-hearth products in the quality field; and now, very specialized steels are being made in high-frequency rather than in arc furnaces. It is apparent then, if industry is co remain healthy, complacency must give way co imaginative planning, based on a thorough knowledge of production technique, a knowledge supplied by efficient research.

Jan 1, 1947

By R. B. Fermor

"AbstractAttention is drawn to the ventilation problems arising from the use of diesel vehicles underground, especially in view of the fact that diesel fumes in combination with other pollutants may be more harmful than diesel fumes alone or the other pollutants alone.Means for minimizing the harmful effects of using diesels underground are listed, and the quantities of air' required in mines in which diesel-powered vehicles are used are discussed. Mines are classified in three categories on the basis of severity of ventilation problems, and statistics are given for these categories.Details of the various components contributing to total ventilation needs are given, and the ventilation needs of individual mines in the three categories are listed. A description is given of the principles according to which main ventilation coursing is planned and the selection and siting of main fans is discussed.General Considerations in the Use of Diesel-Engined Vehicles UndergroundIN ORDER to reduce physiological hazards, present and latent, to workers in mines in which extensive use is made of diesel equipment underground, it is important that mine ventilation systems reduce the concentrations of rock dust, diesel fumes and particulate matter as rapidly as possible to an acceptable level in all parts of the mine.There is some evidence that the long-term effects of a combination of the above pollutants are greater than those of anyone of them alone, which makes the problem even more pressing."

Jan 1, 1977

By Kazutoshi Haga, Batnasan Altansukh, Atsushi Shibayama, Ryuji Oinuma

"Recently, the arsenic grade in copper ores has been increasing year by year. Arsenic bearing minerals (enargite (Cu3AsS4) and tennantite (Cu12As4S13)) coexist with typical copper minerals such as chalcopyrite (CuFeS2). The removal of arsenic from copper ores that contain relatively high arsenic content is essential due to its adverse impact on the environment and the resulting economic consequences. In this study, arsenic removal and dissolution behaviour of Cu and As from enargite (Cu3AsS4) were investigated using ferric sulphate (Fe2(SO4)3) solutions containing sodium chloride under high pressure oxidation conditions. The effects of numerous parameters including the concentration of Fe2(SO4)3 and NaCl, temperature, total pressure, leaching time and particle size were studied while other variables such as pulp density and stirring speed were fixed at 100 g/L and 750 rpm. The results showed that more than 60% of the copper was dissolved in a 0.1 M ferric sulphate solution under the high pressure oxidative conditions, whereas the leaching rate of arsenic was less than 20%. SEM observation revealed that elemental sulphur was deposited on the surface of enargite forming a passivation layer and the residue was agglomerated. Those phenomena may cause a decrease in the copper leaching rate. It was found that more than 80% of copper was dissolved in the ferric sulphate solution in the presence of 0.34 M sodium chloride under the conditions optimized, whereas the dissolution of arsenic in the mixture did not exceed 2%. XRD analysis of the solid residues from the leaching experiments used ferric sulphate and mixtures of ferric sulphate and sodium chloride showed arsenic to be present as scorodite (FeAsO4).INTRODUCTION In recent years, there has been an increase of the arsenic (As) content of copper ores due to the gradual depletion of high grade copper ores. In some copper deposits, arsenic occurs in the form of minerals such as enargite and tennantite. The removal of arsenic in ores containing copper is critical to the production of pure copper and the management of the environmental challenges caused by the smelting process. Due to the environmental risk caused by arsenic emission and the deteriorated quality of the copper product, smelting of enargite concentrates is not an effective method for the extraction of copper (Padilla et al., 2010; Safarzadeh et al., 2014; Long et al., 2012). Therefore, a number of studies have been carried out to develop arsenic removal technologies from copper ores using various methods such as hydrometallurgy (Curreli et al., 2009; Tongamp et al. 2010), pyrometallurgy (Dalewski., 1999; Padilla. et al, 2012) and bio-oxidation (Ehrlich, 1964; Sasaki et al., 2010). Several hydrometallurgical leaching processes like sulphuric acid, alkaline sodium sulphide and sodium sulphate and ferric sulphate leaching have been developed to treat enargite ores and concentrates. The alkaline sodium sulphide leaching process has been developed for the removal of arsenic from enargite (Anderson, & Twidwell, 2008; Parada et al., 2014). The mechanism of the dissolution of arsenic from enargite in sodium sulphite solution is"

Jan 1, 2016

By V. Gangrade

Recirculation is the major concern associated with the utilization of booster fans. In controlled recirculation, a portion of the return air is purposely mixed with the intake air and the mixture is directed towards a working district, while the air quantity and gas concentrations in the air are closely monitored and managed. The objectives of this study were to determine the gas concentration in intake and return airways during controlled recirculation, and to determine the recirculation fraction for multiple headings. Experiments were conducted in a laboratory model to determine the effect of controlled recirculation on the quality of air circulated through the working faces. Preliminary results showed that recirculation is beneficial to ventilation planning because it reduces the build-up of air contaminants at the working faces and reduces the overall power consumptions. The experimental results were used to quantify the recirculation fraction and to calibrate ventilation models of the laboratory model. These models are used to simulate the controlled recirculation and to predict the gas concentrations in multiple headings.

Aug 1, 2013

By A. J. Stapleton

"This paper gives a brief description of the occurrence and development of the Needle Mountain mine at Gaspe Copper Mines, Limited and describes the trackless mining equipment used in this highly mechanized underground operation.Maintenance of the trackless equipment is considered in detail, with particular emphasis on scheduling and control, examination and inspection. All maintenance is carried out in an underground garage, and the facilities for maintenance and field repairs are also described. Maintenance costs are given for various units and the figures for different types of loading and haulage units are compared to support the trend toward larger units and the increasing use of rubber-tired loaders."

Jan 1, 1969

By S. B. Mishra

Ni-20Cr metallic coating was deposited on a Ni-based Superalloy (3Fe-19.5Cr¬0.3Ti-Balance Ni) by a shrouded plasma spray process; NiCrA1Y was used as a bond coat. Erosion studies were conducted on uncoated and plasma-spray coated superalloy specimens using an air-jet erosion test rig at a velocity of 40 m/s and impingement angles of 30° and 90°. The coating has been characterized for porosity, microhardness and microstructure and X-Ray Diffraction (XRD). An electron probe micro analyzer (EPMA) was used to obtain X-ray elemental mappings of the coating along the cross-section. Scanning electron microscope (SEM) with EDAX attachment was used to analyze the eroded surfaces.

Jan 1, 2005

By E. L. Bruce

Introduction The Outokumpu copper mine is situated in eastern Finland, 50 kilometers west of the city of Joensuu or 225 kilometers directly north of the city of Viborg (Viipuri), which is situated at the eastern end of the gulf of Finland (Figure 1). The ore-body was discovered in 1910 by Dr. Otto Trüstedt after two years of careful, scientifically-directed, search. During the early period of development of the mine, the ore was treated locally and the copper re-covered by an electrolytic process. Now the ore is concentrated by tables and by flotation. The concentrates are shipped to Germany for refining. In 1929 the mine produced 150,000 tons of ore from which between 20,000 and 25,000 tons of flotation concentrates containing 20 per cent copper were produced. Profits in 1929 were approximately half a million dollars, but the present price of copper will affect very seriously the profits for 1930. The ore reserves are given as between 7 and 8 million tons (1). The grade of ore is stated to be 4 percent to 6 percent copper, with a little zinc.

Jan 1, 1931

By Courtney E. Cleveland

THE gold deposits of the Pioneer and Bralorne mines, in the Bridge River district of British Columbia, are closely associated with a long, narrow intrusive body of extremely variable composition, outcropping on the northeast side of Cadwallader creek and lying almost entirely within the property boundaries of the two companies. Other masses of the same type of intrusive rock are found in the district, more or less along the line of the main axis of the Pioneer-Bralorne in trusive, and have associated with them variable amounts of gold-quartz mineralization (Figure 1). The ore deposits of the district have been the subject of investigation by officers of the Geological Survey of Canada at various times during the past 25 years, and articles on the geology and mines of the district have been published by various individuals in technical journals. A list of the more important re-ports follows: SELECTED BIBLIOGRAPHY

Jan 1, 1938

By Abhinav Karanam, Lukas Bichler

Yttria Stabilized Zirconia (YSZ) is a promising thermal insulator for high temperature environments due to its thermal stability and chemical inertness. As was demonstrated with other technical ceramics (e.g., Alumina), addition of Single-Wall Carbon Nanotubes (CNTs) to a ceramic matrix may significantly enhance the mechanical properties of the composite ceramic. In this work, 8 mol% YSZ with 0.2, 0.5 and 1wt% CNTs composites were prepared via Spark Plasma Sintering process. The densification, Vicker’s microhardness, specific gravity and microstructure evolution of the composites were investigated. The results suggest that the addition of up to 1wt% CNTs to YSZ yielded optimal combination of the studied properties. At higher addition levels, the specific gravity decreased and clustering of CNTs occurred, leading to poor densification and a relative loss of performance.

Jan 1, 2014

By J. M. Harrison

FIELD PARTIES of the Geological Survey of Canada have, in recent years, mapped several areas east and northeast of Flin Flon (9, 10, 12, 13, 14, 15, 118) (1). In all these areas the mineral deposits show a close geographical relation to faults although the immediate control of most of the known ore deposits appears to be folded structures in the rocks (8, 11, 18, 19). Air photographs and published geological maps were studied in order to ascertain whether or not the mineral deposits in the Flin Flon-Snow Lake mineral belt as a whole show any spatial relationship to faults. It was found that most of them do show a distinct geographical association with faults, or with topographic features that may be faults. It is further apparent on air photographs that a major lineament, for composite of lineaments, follows approximately the contact between gneisses and schists of the Kisseynew complex on the north, and Amisk volcanic rocks on the south. However, this Kisseynew lineament is not continuous and, especially in the eastern half of the district, it is exceedingly irregular in plan. Parts of this lineament have been mapped as faults (9, 10, 12, 14), other parts have been shown as stratigraphic contacts (1, 2, 21, 27), and still other parts have not been studied except by reconnaissance methods. It is suggested that the Kisseynew lineament may be due to a deformed fault that extends easterly from a point about 25 miles west-northwest of Flin Flon to a point at least 10 miles northeast of Wekusko lake and that the mineral deposits.

Jan 1, 1951

By Edward P. Barrett

Iron ore, when subjected to reducing gases at a temperature suitable for reduction of the oxide but not high enough to melt the ore or metal formed, is converted into metallic iron. The product, being the original piece of iron oxide minus its oxygen, is sponge-like in appearance when viewed under a magnifying glass, and hence is called 'sponge iron. Sponge iron was probably the form in which some of the first iron was recovered from the ores. As early as the eighth century the Catlan forge developed into a low shaft furnace known as the high bloomary, in which iron was produced in the form of a pasty mass. These furnaces were increased in height, and with increased temperatures came the production of liquid cast-iron, at first undesirable because of lack of knowledge of methods for working it. In 1340 the first true blast-furnace was built iri Belgium. Some castings were made, but the greater part of the iron was converted into wroughtiron blooms by a crude puddling process. Charcoal was the universal fuel until the latter part of the seventeenth century, when coke was first used in England. Larger scale developments of methods of refining pig-iron followed. In I 885 Bessemer built his first converter in England, and within a few years the Siemen' s regenerative open-hearth furnace was developed, also in England, to produce steel. Then followed the enormous expansion in the metallurgy of iron. The idea of a direct process for the production of iron and steel has persisted during all of this time.

Jan 1, 1925

By P. Marcotte, G. LeBlanc, S. Ouellette, J. Boutin

"To characterize noise and vibration sources of different types of mining equipment used in underground mining, the authors performed a study in eight Quebec mines on 28 pieces of equipment. This paper presents the procedure followed to select the equipment to be evaluated, and the low-cost acquisition system developed to perform multichannel time-domain data acquisition in harsh environments. It also presents the results obtained for the noise level produced by the equipment and for handarm and whole-body vibration exposures.RÉSUMÉ Dans le but de caractériser les sources de bruits et de vibrations de divers équipements miniers utilisés sous terre, les auteurs ont étudié 28 équipements dans huit mines du Québec. L’article présente la procédure suivie pour choisir les équipements à évaluer ainsi qu’un système multicanal à faible coût développé pour acquérir des données dans des environnements difficiles. Il présente aussi les résultats obtenus pour les niveaux de bruit produit par les équipements et pour les expositions main-bras et du corps entier aux vibrations."

Jan 1, 2015

By R. P. Nicholson

On September 3rd, 1947, the Acadia Coal Company put into operation a central coal preparation plant. This plant was designed to process all coals mined by this Company in the Pictou County coal field. The problem, briefly, was to make a three-way separation of the raw coal fed into the plant. It was desired to remove all stone, metal, and wood from the marketable coal and to produce a splint coal from the raw material which would be suitable for making power. This splint coal product is belted directly to the power plant which is adjacent to the wash plant. To attain this object it was therefore necessary, first, to wash the raw coal, removing all splint, stone, metal, and wood. The stone, metal, wood, and highest-ash splint had then to be removed by a second washing in order to obtain the lower-ash splint for use in the power plant. The plant is on the east side of the Allan colliery, in the town of Stellarton (see accompanying photograph). It is of steel frame construction with wood siding, covered on the exterior with corrugated galvanized iron. Considerable concrete had to be poured for the foundation piers as the plant site is largely 'fill' ground. This necessitated the construction of extremely heavy footings containing a large amount of reinforcing steel. In all, 884 cu. yds. of concrete were poured for the various pits, tanks, and foundations; its average test was about 3,500 lb. per square inch. At the time the plant was constructed, the steel shortage in Canada and the United States was acute and, in order to obtain steel for the structure which is four stories high- an unused part of the Allan bankhead was torn down. Enough steel was obtained from this demolition to fabricate the new plant.

Jan 1, 1948