Search Documents

By C. Nikolic

A process utilizing ozone for the precipitation of cobalt from nickel sulphate liquors containing ammonium sulphate has been developed. Best results were obtained using nickel carbonate to maintain solution pH at 5.0 to 5.5. Work was performed both in column and stirred-tank reactors. Variables studied included neutralizer type and concentration, NH4+ concentration, temperature, Ni++ and Co++ concentration, per cent O3 in the O2 carrier gas, O3 input rate and agitation. The over-all rate of cobalt rejection increased sharply with increasing agitation and ozone concentration in the gas phase, reflecting relatively slow transfer of ozone from the gas to the liquid phase.

Jan 1, 1978

"In response to mine head grades declining and orebodies becoming more complex, Glencore Technology has developed an alternative method for recovering economic minerals once leached into solution, rather than relying on conventional flowsheet options. The method involves the precipitation and separation of base metals from solution with limestone or lime. The final grade of these precipitate is not usually high enough to attract favourable terms of sale due to dilution from gypsum and sulphate salts. A set of operating conditions have been developed to allow the separation of the base metal precipitate from gypsum by exploiting the difference in particle size. A high-grade oxide product can be easily separated from the gypsum stream at very low cost. This process was originally developed by Glencore for zinc and copper systems. This paper reports on the successful application to nickel and cobalt, and this process has significant advantages over the incumbent precipitation process utilising magnesia.INTRODUCTION During evaluation of transitional and oxide zinc ore deposits during the 1990’s, Noranda Inc. (now Glencore) developed a sulphate based ore leach process to extract zinc into solution. For flowsheet development, conventional schemes dictated that once the zinc was dissolved in an acidified solution it was recovered by means of purification or solvent extraction followed by electrowinning and casting to produce zinc ingots. The deposits Noranda evaluated were high grade but had a relatively short mine life (10 years) and economic analysis showed that the projects couldn’t sustain the investment of a full zinc refinery. Compounding this problem was the lack of power supply infrastructure and the high power cost in the region. Noranda then evaluated alternative means of recovering zinc from solution. Laboratory testwork showed that a high-grade zinc precipitate (+50 wt% Zn) could be produced as an oxide, carbonate or sulphide by contacting acidified zinc sulphate solution with a number of reagents including soda ash, sodium hydroxide, and sodium hydrogen sulphide. Economic evaluation showed that the cost of the reagents are prohibitive, especially when the final product is still a metal intermediate (ZnO, ZnCO3 or ZnS). Noranda then continued to focus on fine zinc oxide precipitation for supply into the automotive tyre industry as this product would attract favourable terms of sale as a premium on Special High Grade (SHG) zinc."

Jan 1, 2017

By D. Roy Eccles

A multi-element geochemical response, with contrasts of up to 29 times background, was obtained in soil above the Mountain Lake Diatreme, northwestern Alberta. The overall geochemical signature is indicative of an ultramafic source; geochemical responses contain elevated concentrations of Co, Cr,O, Cu and Ni with the presence of high Ba, Ga, HI, PO,, Rb, Ta, Ti and light rare earth elements suggestive ofa kimberlite or lamproite body. The shape, or morphology, of the enzyme leach-based geochemical signature over the Mountain Lake Diatreme combines moderately strong to strong oxidation halos, or a rabbit's- ear geochemical profile, with a sharply-defined apical geochemical profile. Because some Alberta diatremes discovered to date form positive topographic highs, the resultant geochemical signature may express the soil development profile that forms directly on top of kimberlitic and lamproitic bodies. The enzyme leach technique, which has proven to be a useful tool in base metal, precious metal and petroleum exploration, may have a significant impact on exploration for kimberlite, lamproite and related rocks in Alberta by providing industry with a useful and cost effective tool to probe blind and/or buried anomalies identified by airborne and ground magnetic surveys in areas of glacial overburden.

Jan 1, 2001

By C. H. Hopper

DIAMOND drills have played an important part in the development of mines for many years. Recently. they have also entered the production field arid the use of diamond drills m the primary breaking of ores has become a big branch of the industry. The writer has estimated roughly that the total diamond drilling in Canada during 1942 was 5,625,000 feet, of which 2,250,000 feet, or 40 per cent, was for blast-holes. This accounts for 6,750,000 tons of ore broken, using the conservative factor of 3 tons per foot of hole. Many consider that the use of diamond drills for blast-holes is the most important advance in mine practice of the past decade, and the industry owes a great deal to the staff of Noranda Mines, Limited, for the pioneering they have done in the development of long-hole mining methods and for publishing their results. A great many mines have followed Noranda's lead. At the Waite-Amulet, Aldermac, Flin Flon, Canadian Malartic, Hoyle, and Matachewan Consolidated mines, most of the ore is broken by long-hole blasting. While the mines were developing new methods, the diamond-drill industry was developing mechanically-set bits and better machines. Through the effective use o smaller, cheaper diamonds, as well as more efficient setting, bit costs per foot are only one-half what they were ten years ago. Few people realize that a diamond bit is relatively inexpensive. The common EXT coring bit, for example, contains some 200 small diamonds, weighing altogether about 2.70 carats which, at $3.40 per carat, cost $9.20. After use, the equivalent of about 100 of these diamonds may be recovered. Therefore the true cost of the bit is only $7.00, made up of $4.60, the cost of the diamonds lost, $2.00 for setting, and $0.40 tax. The trend in machines has been toward specialization for the different classes of rock in blast-hole work. Light, high-speed machines have been developed for soft ores and higher powered machines for hard ores.

Jan 1, 1943

By Joseph Hirschi, Behrooz Abbasi, Harrold Gurley, Yoginder P. Chugh

"The research goal was to assess if analytical tool/s can be developed to quantify displacements around a geological fault as longwall face moves toward it and past it. A company was faced with crossing a 2-3 m (6-10 ft.) normal up-thrown fault in the development entries and the face while mining a 375 m (1,200 ft.) wide longwall face. A field monitoring and numerical modeling study was performed to develop data. Field measurements consisted of roof-to-floor convergence and rectangular rosettes in the immediate roof. Numerical modeling consisted of constructing a 3-D structural model using the FLAC3D software with the fault plane incorporated as ubiquitous joint. Based on analyses and field observations data, the coal company was informed of impending movements along the fault plane and likely impacts on the development entries. Additional stiff supports were installed in head gate entries around the stage loader and equipment about 60 m (200 ft.) outby of the longwall face (solid). As the longwall face approached the fault, predicted displacements were documented and manifested by severe loading on the installed supports.BACKGROUND AND STUDY OVERVIEWThis paper summarizes results of a cooperative study aimed at improving longwall mining operations in Illinois. More specifically, the study focused on: 1) In-mine measurements in development entries while mining ahead of and behind a faulted zone, 2) Making observations on stability of pillars and entries while mining through the fault, and 3) Developing simplified analytical structural models using FLAC3D to assess if predictive techniques can be developed to plan mining operations through fault zone. Available data on geometry of the fault with estimates of the cohesion and frictional parameters were used for modeling."

Jan 1, 2015

By R. S. Jones

"Fording Coal Ltd. is now in its fifth year of a 15-year contract to supply 3 million long tons of clean coal per annum to its Japanese steel-making customers. The mine employs both conventional truck-shovel and unconventional ""walking"" dragline coal mining techniques in multiple-seam pits. This paper describes the present and future application of the 60-cu.-yd dragline and truck-shovel pre-stripping fleet in 1•ecovering 5- to 40-footthick coal seams in mountainous terrain. Deep blastholes, coal flow demands, spring ""run-off"", seam and inter-seam thrust faulting, limited seam outcrop data and regional faulting are a few of the problems encountered in this application. The author discusses these problems and their solutions as applied at Fording Coal Ltd."

Jan 1, 1976

RISKGATE is an interactive online risk management system developed by the Minerals Industry Safety and Health Centre (MISHC; University of Queensland) to maximise health and safety performance in the mining industry through implementing continual improvement in management of major unwanted events. A comprehensive knowledge base has been captured for risk management of tyres, collisions, fires, isolation, strata underground, ground control open cut, explosions, explosives, manual tasks and slips/trips/falls. This will be extended to outburst, coal burst and bumps, interface displays and controls, tailings dams and inrush in 2013. RISKGATE presents substantive and leading edge controls to assist industry stakeholders in the design, management and reporting of organisational and regulatory compliance requirements. From a broader industry perspective, RISKGATE provides an environment for knowledge capture and knowledge exchange to drive innovation and best practice in the identification, assessment and management of risk. By capturing operational knowledge from industry experts, RISKGATE provides a cumulative corporate memory at a time of high personnel turnover in the coal industry. All major Australian mining companies are contributing topic experts to this broad industry initiative. In the first 24 months, nine coal mining companies nominated over 80 different experts who contributed over 400 days of individual time to the knowledge capture workshops. RISKGATE is the largest single Australian Coal Association Research Program (ACARP) occupational health and safety (OHS) initiative to date.

Aug 1, 2013

By Jonathan Peck, Carl Hendricks

"Global Positioning Satellite (GPS) based positioning and navigation systems have been recently developed and implemented by AQUILA Mining Systems Ltd. on blast hole drills and electric cable shovels in Canadian open pit coal and iron ore mines. These systems enable the location of the drill bit or the shovel tracks to be accurately determined in three dimensions. The position of the drill or shovel is displayed to the operator via a real-time, Moving Map Display (MMD) on an LCD-VGA screen. The MMD allows the operator to accurately navigate the drill from blast hole to blast hole or maintain a desired shovel grade or face position, with respect to displayed bench features. The maps for the MMD are downloaded from the mine office via laptop or radio link as required or as mining plans change.To obtain reliable, accurate and real-time3D positions of mobile mining equipment, proven GPS technology has to be utilized. The GPS components need to operate reliably under the severe environmental conditions that exist on board mobile mining equipment. In addition, they have to contend with varying pit geometry’s and satellite configurations, with little or no performance degradation. These issues were initially examined in December1993 during a feasibility project between AQUILA and Gregg River Resources Ltd., in relation to implementing GPS systems on blast-hole drills.To achieve certain design objectives, AQUILA Mining Systems Ltd. has developed navigation systems for cable shovels and blast-hole drills based around off-the-shelf, high precision GPS components. These systems utilize the AQUILA Advanced Monitoring Platform (AMP), to display graphically, via the MMD, shovel grade and drill position to the operator to within ±12 inches of design coordinates. Production prototypes have been installed on a Marion 301 cable shovel and a Bucyrus-Erie49-R Series III drill at the Fording River Mine in August, 1995, at the Wabush Mine on a Bucyrus Erie 190-B shovel in June, 1995, and on a GD120 drill at Gregg River Resources Ltd. in January, 1996. All these systems have undergone field trials to test system components and functionality’s under actual production conditions. This paper will discuss these GPS-based positioning and navigation systems in subsequent sections."

Jan 1, 1997

By Roland B. Hoag, Roger G. Webber

Sulphate concentration in groundwater is a good measure of the extent of oxidation of sulphides, provided that sulphide minerals are the primary source of the sulphate. A study was conducted near the Eustis Mine in Quebec to determine where and how the sulphate in groundwaters originated. Atmospheric precipitation is the only source of sulphate other than oxidation of sulphides, and in this study area it is equal to 0.01,. millimole per litre. The oxidation of sulphides can be divided into subsurface oxidation (mainly inorganic processes) and surface oxidation (including both organic and inorganic processes) . The maximum sulphate concentration due to subsurface oxidation of sulphides depends on the solubility of 0 2 in water and is 0.25 millimole per litre. Surface oxidation is, therefore, responsible for any amount greater than atmospheric plus subsurface contributions (0.29 millimole per litre). Surface inorganic oxidation occurs in waters with a pH greater than 15 and is controlled by the kinetics of the oxidation processes. Organic (bacterial) surface oxidation is dominant only in acid (pH< 1.5) waters. The bacterial action accelerates the oxidation of sulphides, and large quanttties of sulphate may be introduced into solution.

Jan 1, 1976

By J. C. Gibson, C. H. Stockwell

"The San Antonio gold mine is at Bissett, Manitoba, on the north shore of Rice lake, 100 miles northeast of Winnipeg. Gold was discovered on the property in 1911, but intensive exploration was not undertaken until 1926. Milling commenced on May 1st, 1932. Total amount of ore milled from that time until the end of 1946 was 1,766,670 tons, having a value of $18,378,317.GENERAL GEOLOGYThe rocks in the vicinity of the mine are Precambrian and include three groups, namely, the Rice Lake series of volcanic and sedimentary rocks, basic and acidic intrusions, and a younger formation of sediments known as the San Antonio formation (Fig. 1). The lower part of the Rice Lake series, consisting of flows of rhyolite, trachyte, and andesite with interstratified beds of agglomerate, occupies an area extending southward from Rice lake. The lake itself and the country to both east and west of its northern end is underlain by the next succeeding beds of the series, which are chiefly tuffs, arkose, and conglomerate, but include a thin band of basalt. Northward from the lake, these are succeeded by the upper beds of the series, first a thin band of basalt and, overlying this, porphyritic andesite flows interlayered with beds of volcanic breccia or agglomerate.The Rice Lake series has been invaded on the east side of the lake by a body of basic rock ranging in composition from gabbro to diorite and quartz diorite, now much altered. This is cut by younger sills and dykes of basic rock, probably diabase, the original texture of which is largely destroyed by alteration. Numerous dykes of feldspar porphyry, quartzfeldspar porphyry, and a few of a rhyolite-like rock, occur south of the lake, but are uncommon to the north. They cut the diabase and older rocks.Extending westward from Rice lake and lying with marked angular unconformity against all of these rocks is the San Antonio formation, consisting of cross-bedded, arkosic quartzite."

Jan 1, 1954

By M. H. Haycock

Introduction The property of Rouyn Merger Gold Mines, Limited, is in Rouyn and Joannès townships, Western Quebec, seven miles east of the town of Rouyn. Traversing it is the east-west trending Cadillac-Bouzan fault. Diamond drilling in 1944 and 1945 along a shear zone south of the fault indicated an ore deposit lying at the contact between sedimentary and volcanic rocks and dipping approximately 60° to the northwest. In the summer of 1945 it was decided to sink a shaft to investigate the indicated ore zone. In the immediate vicinity of the deposit, bed-rock is overlain by clay beds, in some places as much as 70 feet thick. Consequently, possible shaft sites were limited to those locations where overburden would not be excessive. The most favourable site was about 125 feet to the south of the ore zone as projected vertically from bed-rock to the surface. Accordingly, it was decided to sink the shaft at this point, with an inclination of 60° N. W., paralleling the dip of the ore zone.

Jan 1, 1948

By K. Blower

"Since there was no representative from Wesfrob Mines Limited, the information on their infra-red concentrate drying operation, which had been prepared by Mr. K. Blower, was presented by Mr, Dorland. Mr. Blower, in submitting the information, emphasized that their objectives in this operation were (a) to guarantee less than 90%, of flow-moisture in their copper concentrates and thus satisfy marine shipping regulation• and (b) to minimize capital costs, The infra-red dryers have satisfied these objectives.To control final moisture in the copper concentrate, current practice is to preheat the filter cake with steam in the disc filter hood and then conveyor-0r7 the concentrate with infra-red calrod heaters. The application of steam aids the system as follows:1) Improves vacuum pump efficiency.2) Lowers viscosity of filtrate (increased temperature},3) Preheats the cake prior to radiant heating. (150°F)The hot cake discharging from the filter ranges from 10.6 to 10.9% moisture. After radiant heating the moisture level is reduced to 8.5% - 9.7% depending on production rate. Further moisture loss occurs during conveying and transferring to the stockpile for a final shipment moisture ranging from 8.1% to 9.5%. Production rate is frail J to 5 dry short tons per hour.1) #23 Conveyor 18"" flat belt covered from filter discharge to transfer point with 7 heaters end-to-end. Drive - Reeves Vari-Speed, 31:4 ratio, type 332-10-18, class ""D"", driving through a 24:1 ratio Dodge reducer. Speed of Conveyor - 3,9 feet per minute to 19.6 feet per minute. (Speed has been established and is not changed as a rule from the present level of a1:out 15.)2) #23 Conveyor 24"" wide, 20° troughed belt covered with 21 heaters, end-to-end from loading point, Speed - Constant at 54,2 feet per minute."

Jan 1, 1972

By H. Craig Boyle, Craig H. B. Leitch

"The Trout Lake stockwork molybdenum deposit is located in the Selkirk Mountains of British Columbia, 50 km southeast of Revelstoke. The property is being explored by a joint venture between Newmont Exploration of Canada and Esso Minerals Canada.The deposit is associated with a small granodiorite stock of Upper Cretaceous age (76 Ma) which has variably altered the surrounding schists, argillites and marbles of the lower Paleozoic Lardeau Group to hornjelsic biotite schists and skarn. The intrusive is composed of a small stock and an intersecting network of northeast- and northwest-trending dykes at surface that coalesce downward into a larger stock. There are two main phases of intrusion, with an earlier quartz porphyritic granodiorite cut by an intra-mineral ""quartz diorite"" porphyry. A strong sub-vertical north-trending fault controls the distribution of the mineralized stock work and displays post-mineral movement.Molybdenite, accompanied by pyrite and pyrrhotite, is mainly present along the margins of veins in a well-developed quartz stock work, but occasionally is strongly disseminated in microfractured intrusives. The stock work is strongest in and around the contacts of the intrusive and its apophyses, and occurs over a vertical range of more than 1,000 m. As defined by the 0.10% MoS] contour, the main mineralized zone is up to 300 m long by 200m wide. Preliminary drill-indicated reserves, currently being revised, are approximately 50 million tonnes of 0.23% MoS2, within which are several zones of higher-grade material. Hydrothermal alteration, as defined by quantitative X-ray diffraction studies on composite core sections, is composed of a central quartz/K-feldspar/albite/minor biotite zone coincident with molybdenum mineralization, which is overlapped by a slightly later, antipathetic quartz/ sericite/pyrite zone. Ankeritic carbonate is also a common alteration mineral, but only traces of fluorite, and no topaz or sulfosalts, have been observed. Analysis for trace elements such as Sn, W, Bi, Sb, As, Hg, U, Ag, Au, Mn, Cu, Pb, Zn and F has been limited except for Sn and W, which appear to be zoned inside and outside the Mo zone respectively; the other elements do not show detectable patterns thus far."

Jan 1, 1983

By A. Zorkovská, S. Castro, P. Baláž, Z. Bujnáková

Enargite (Cu3AsS4) belongs among refractory copper minerals with very low hydrometallurgical extractability of copper. An application of enargite leaching in acid solutions leads to simultaneous dissolution of copper and arsenic and the final leach solutions have to be treated for the separation of both elements. However, the alkaline leaching of enargite is selective. Arsenic passes into leach while produced copper sulphide represents the raw material suitable for pyrometallurgy. The hydrometallurgical processing of mineral can be influenced positively by mechanochemical route. We have shown that more than 80 % of arsenic can be extracted from enargite concentrate by atmospheric alkaline leaching at 95 °C when mechanical activation in an attritor is applied. The produced Cu2S can be further treated with elemental iron where mechanochemical intervention is applied in the second stage of enargite processing. The final product forms Cu/FeS nanocomposite from which copper nanoparticles can be easily separated. The illustrated concept of copper obtaining from copper sulphide is an example of so-called “dry” processing, as reactions in gas and liquid phases are excluded. This concept of environmentally friendly metallurgical processing can be classified as an impetus for novel technology to produce copper from enargite concentrates.

Jan 1, 2012

By Takahiko Okura, Chiharu Tokoro, Shunta Shibuya

Copper concentrates bearing arsenic as enargite (Cu3AsS4) or tennantite (Cu12As4S13) have disadvantage on copper smelting environmentally and economically, so those concentrates should be treated decently. In this paper, some experiments of arsenic removal from several kinds of copper concentrates by heat treatment in an inert atmosphere were discussed. In this study, several samples in which arsenic contents varied 0.18 to 8.3 wt % were heated to the temperature range of 400 °C to 700 °C under argon gas flow during 1 hour. The heat residues and volatilized materials (V.M.) were analyzed by XRD, XRF, ICP-AES, XAFS and MLA to analyze residual concentration of arsenic and residual mineral composition. Experimental results showed that arsenic removal from copper concentrates advanced in 2 steps; at the temperature range of 500 ° C to 550 °C and of 550 °C to 650 °C, respectively. MLA analysis showed that a few of arsenic in enargite was removed by 550 °C heating and a majority of it was still combined with copper and sulfur as tennantite. On the other hand, arsenic in tennantite was removed almost completely by 650 °C heating. Furthermore, a particular type of arsenic mineral, such as Cobaltite (CoAsS) still remained after heating at 700 °C.

Jan 1, 2014

By A. M. A. Mohamed, F. H. Samuel, S. Valtierra, H. W. Doty, A. M. Samuel

"The influence of Fe, Mn, Cu and Mg alloying additions, Sr modification and grain refinement on the microstructure of as-cast and solution heat-treated Al-10.8% Si alloys was investigated using optical microscopy and EPMA techniques. The results showed that the modification effect of Sr diminished with increasing Cu and Mg additions, due to Sr-Cu-Mg interactions. Strontium caused segregation of AlzCu in areas away from eutectic Si regions, and altered the precipitation sequence of the a-Ah5(Fe,Mn)3Siz iron intermetallic from post-dendritic to pre-dendritic, with the phase observed within the a-Al dendrites. Depending upon the alloy Fe and Mn content, a coarser variation (""sludge"") of the a-Fe phase occurred, in the form of polyhedral shaped particles. The AhCu phase dissolved almost completely during solution heat treatment, while Al5Cu2Mg8Si6, sludge, and a-Aln(Fe,Mn)3Siz phases persisted in all alloys, particularly at high Mg and Fe levels. The f3-Al5(Fe,Mn)Si phase dissolved partially in Sr-modified alloys, the dissolution becoming more pronounced after solution heat treatment."

Jan 1, 2006

By Dean Millar

Clean, green, cheap compressed air can be produced efficiently and renewably by modernization of a 19th century technology ?The hydraulic air compressor has no moving parts ?After commissioning, the Ragged Chutes HAC operated for 70 years, only being stopped twice for repairs to the intake heads ?Operates using hydropower from Montreal river ?Produced air for ~29 silver mines in Cobalt, 20 km distant

May 1, 2013

By S. H. Ash

No single factor in modern civilization has played a more important part in the lives of our people than mechanization in industry and to it civilization owes much of its progress. In no industry has mechanization met more opposition than in coal mining, where ?the introduction of mechanical equipment has been opposed on many fronts for economic and social reasons. The term &apos;mechanization? as used in this report refers to the application of machinery to cutting, loading, and transporting coal from the face to the mine cars. During 1933, 84.7 per cent of the underground production of the bitu-minous-coal mines of the United States (1) was cut by machines, while in Washington only 17.6 per cent was machine-cut. Information in this report has been obtained from personal observations and from operating officials in the Roslyn-Cle Elum coal fields, especially D. R. Swem, manager of coal operations, and Thomas Murphy, superintendent, of the Northwestern Improvement Company, to whom the author is indebted for assistance. INTRODUCTION Although Washington coal-mining problems relating co mining methods, ventilation, drainage, and preparation of coal have been discussed in many publications, little has been published on mechanization in this region, principally because it has not been accepted generally that mining machines, mechanical loaders, and conveyors are necessary or economically adaptable to the variable and steeply inclined coal beds of Washington. Production of coal in Washington reached its maximum in 1918, when 4,128,424 short tons were produced; from that year, the trend was downward until 1934, when production was 1,383,103 short tons, the lowest since 1898; for the past two years, production has risen steadily.

Jan 1, 1937

By C. H. Buck, A. J. Taylor

"In 2015 Vale’s Clarabelle Mill began the process change to enable a higher degree of Cu separation. The flowsheet modification was part of a complete divisional flowsheet change being implemented in Vale’s Sudbury Operations. This paper will centre on some of the Operational Readiness (OR) work, culminating in the commissioning of the circuit in March 2017. The emphasis will be on the implementation of an integrated test plan to prepare for the process flow change through the mill.BackgroundClarabelle Mill (CBM) began making a saleable Cu concentrate in 2006 with the installation of the Cu separation circuit. Typical separation rate was 35-40% of Cu in feed reporting to Cu concentrate based on a target Ni concentrate Cu:Ni target of 0.7-0.8. The remainder of the recovered Cu (55-60%) reported to Ni concentrate and was smelted through the Copper Cliff Smelter.In 2013 a capital project, Surface Facility Upgrade (SFU), was implemented to focus on matching the surface plants capacities with the future mine plan to maximize revenues. This was to be achieved by redistributing the metal flow, specifically Cu, through CBM to increase metal unit content through the Smelter. The amount of redistribution of Cu was determined to be based on maintaining a stable Cu to Ni ratio (Cu:Ni) in the Ni concentrate.The change in Cu:Ni ratio in the Ni concentrate would affect the Sudbury divisional flowsheet, and required process changes across the all of the surface plants. The detail that surrounds the flowsheet changes as a whole will not be discussed, but the outcome of the decisions plays a large role in the operational readiness interactions between the mill, its suppliers and its downstream customers."

Jan 1, 2018

"The Cordillera contains numerous porphyry deposits and prospects, many containing economic quantities of copper, molybdenum, gold and tungsten. Over the lost twenty years, different phases of exploration have been driven by individual commodity prices and new discoveries. Exploration methods have remained largely unchanged since the 1960s and 1970s with the range of techniques chosen for each situation depending on the stage of the program, the type of porphyry target and the local environment. Improvements or changes to techniques have resulted from awareness of specific features in new deposits or regional problems. During the last ten years much of the emphasis has been on the re-evaluation of known porphyry deposits with more exploration in areas previously recognized as prospective. Re-evaluation of known deposits has resulted in increased reserves, often with improved gold grade, and the discovery of new zones. Several new deposits have been discovered including gold-only deposits of probable porphyry affinity.Research related to porphyry deposits has followed trends in exploration and has been directed toward the type of deposits that have been of current interest. In addition to research on specific deposits and areas, general research related to porphyry deposits has addressed three broad themes. The first theme involves the role of tectonic processes and the nature of source regions. Although different in detail, recent tectonic models suggest that a tectonic change or hiatus may be important for the generation of metal-rich magmas from various source regions and subsequent fractionation that permits volatile saturation. The second theme is based on magmatic processes, particularly the generation of a volatile phase enriched in metals. This research supports the general orthomagmatic model for porphyry deposits and has helped to define the influence of specific variables in the generation of different types of porphyry deposits. Finally, research on alteration and mineralization has provided evidence for different types of fluids and fluid processes involved in the formation of porphyry deposits. These data also support the orthomagmatic model but indicate additional complexity in magmatic-hydrothermal systems including the role of external fluids. Although important advances have been made, research has had a limited impact on exploration.Exploration and research on deposits that occur in the peripheral and upper parts of porphyry systems have been important over the last ten years. Although considerable advances have been made, the relationship of different styles of peripheral mineralization to magmatic processes in the core of the system remains ambiguous. An improved understanding of the processes that generate zoning, peripheral mineralization, and the surrounding alteration envelopes would be beneficial to exploration."

Jan 1, 1995