Search Documents

By T. W. Wlodek

"AbstractThe results of research into the fatigue properties of SAE 1080 carbon steel and nickel-chromium-molylbdenum steel for mining drill rods are analysed and described in detail.The effect of water corrosion on the fatigue strength of drill rods of these two steels in the as-rolled condition has ,been investigated and the beneficial influence of shot-peening on their dry and water-corrosion fatigue strengths determined by employing the method developed previously (1).Eight S-N curves for as-rolled and shot-peened mining drill rods under both dry and water corrosion conditions have been derived and their shape and relative position are discussed. The main features relating to field performance of the drill rods are analysed.Purpose of Research and Outline of ProgrammeDRILLING holes in rock and ore by means of drill rods attached to a pneumatic drill is a basic procedure required in mining operations. Detonation of explosives placed in these holes is at present the only practical method of breaking down the rock and ore.A drilling rod is supported by its bit end in the drilled rock. Its shank end, fixed in the drilling machine, transmits impact energy to the cutting edges of the bit. On the field performance of the drill rod depend a number of basic mining operations such as sinking, drifting, and stoping. The drill rod is there-fore regarded as one of the most important tools used in the mining industry."

Jan 1, 1952

By A. J. Monhemius

"This paper reviews the history of modern iron-control processes in hydrometallurgy. Attention is paid to processes developed in the electrolytic zinc industry for removal of iron from zinc sulfate leach liquors and the problems faced by the industry in the safe disposal of the iron residues produced by these processes. Past lessons learned are projected onto current efforts to develop hydrometallurgical processes for treatment of copper sulfide concentrates. It is argued that any attempt to create a “hydrometallurgical copper smelter” will fail, unless methods are developed that can recover iron in a form that can be directly used by the steel or pigment industries.RÉSUMÉ Cet article passe en revue l’histoire des procédés modernes de contrôle du fer en hydrométallurgie. Il accordera une attention particulière aux procédés développés dans l’industrie du zinc électrolytique pour l’élimination du fer dans les liqueurs lixiviantes de sulfate de zinc anhydre, ainsi qu’aux problèmes rencontrés par l’industrie en termes d’élimination sans danger des résidus ferreux générés par ces procédés. En projetant les leçons tirées du passé sur les efforts actuels, on pourra développer des procédés hydrométallurgiques pour le traitement de concentrés de sulfure de cuivre. Beaucoup prétendent que toute tentative de créer une « fonderie de cuivre hydrométallurgique » échouera à moins de développer des méthodes permettant de récupérer le fer sous une forme pouvant directement être utilisée par les industries sidérurgique ou des pigmentsINTRODUCTIONThis paper resulted from an invitation to the author from the CIM’s Historical Metallurgy Committee to give a presentation on the early developments of iron control in hydrometallurgy. This was to take the form of a plenary lecture at the 4th Symposium on Iron Control in Hydrometallurgy, which formed part of the 28th International Mineral Processing Congress, held in Quebec City in September 2016.I was naturally flattered that the invitation was to give the lecture at an IMPC, the prestigious conference series that has been held since the 1950s. That this particular IMPC was to include the 4th Symposium on Iron Control in Hydrometallurgy, a conference series held only every 10 years, made the invitation even more appealing and appropriate. This was because I had been co-chairman of the First Symposium on Iron Control, together with my erstwhile colleague, John Dutrizac, which was held 30 years ago in Toronto."

Jan 1, 2017

Training by Inclusiveness ?Background ?Video ?Results ?Partners ?How SEM works ?Future of SEM Background: Inclusivity partners ?Northwest Community College ?Smithers Exploration Group ?With support from the Province of BC ?Federal government ?And First Nations across the northwest

May 1, 2010

By Wayne N. McKee, Scott A. Lewis

"Introduction to the Syncrude OperationSyncrude Canada Ltd., located 42 km north of the city of Fort McMurray, Alberta, (Fig. I) is an integrated operation that has produced synthetic crude oil from the Athabasca oil sand deposit since 1978.The operation, consisting of a surface mine, an extraction plant, a bitumen upgrader, and a utilities plant, is currently capable of producing over 60 million barrels of crude oil per year. Production is expected to increase to 70 million barrels of crude oil per year over the next five-year period with no major changes to equipment or process planned.The Syncrude surface mine, producing a total of 675 000 tonnes of ore and waste per day, rates as one of the largest mines in the world. A strip mining method is utilized, with two or three operating benches necessary to excavate a total depth varying between 60 m and 70 m. The 20 m to 30 m of overburden is removed by electric and hydraulic shovels and 200-ton haul trucks, and dumped in the mined-out pit for final storage. The overburden operation creates a flat bench near the top of the ore zone on which the four 60 m3 draglines operate. The draglines excavate interbanded ore and waste in the highwall, with ore placed on the operating bench in windrows, and waste returned to the mined-out pit. The windrowed ore is reclaimed by four bucketwheel reclaimers, and discharged onto a conveyor system for transfer to the extraction plant."

Jan 1, 1993

By J. Asfahani

"The inverse slope method (ISM) was applied to reinterpret vertical electrical soundings (VES) data from pits at the Al-Sharquieh phosphate mine, in order to demonstrate applicability and suitability of the ISM for interpreting VES data from sedimentary phosphatic environments. The ISM overcomes limitations of the curve matching method and the complexity of lithological sections. The ISM geo-electrical interpretation results correlated well with lithologies of the pits. This method characterized resistivity and thickness of the phosphatic layer, and identified favourable phosphate-prospecting areas using the newly developed thickness/depth parameter. The ISM is recommended for interpreting VES measurements in similar sedimentary phosphatic regions.RÉSUMÉ La méthode d’inversion de la pente (ISM) a été utilisée pour réinterpréter les données de sondages électriques verticaux (VES) effectués dans des puits de la mine de phosphate Al-Sharquieh, afin de démontrer l’applicabilité et la pertinence de cette méthode pour interpréter les données VES dans des environnements de sédimentation de phosphates. Cette méthode (ISM) surmonte les limitations de la méthode de comparaison de courbes et la complexité des sections lithologiques. Les résultats de l’interprétation géoélectrique ISM correspondaient bien aux lithologies des puits. Elle a permis de caractériser la résistivité et l’épaisseur de la couche phosphatique et d’identifier les secteurs favorables à la prospection pour le phosphate en utilisant le paramètre nouvellement développé épaisseur/profondeur. ISM est recommandée pour l’interprétation des mesures VES dans des régions semblables où se trouve du phosphate sédimentaire."

Jan 1, 2016

By Biplop Das, E. Herrera, A. Burrows, P. J. Mackey, G. R. F. Alvear Flores

Since the first commercial plant was built at Mount Isa, another twenty ISASMELT™ furnaces have come into commercial operation, and construction of new plants continues. The primary copper ISASMELT™ top submerged lance (TSL) technology continues to attract interest from potential users who seek to smelt productively. In addition to the known benefits of productivity and flexibility, ISASMELT™ operators have also achieved improvements to energy efficiency when switching from their previous technologies. The recent production statistics for operation at Tuticorin, India show that ISASMELT™ has taken the first steps into territory beyond 400,000 t/y (copper cathode basis) and this will likely be the scale chosen by future new copper smelters operating purely on a toll smelting basis. Highly energy-efficient technologies will be expected at these smelters

Jan 1, 2015

By George W. Bain

Summary During the last three years the discovery of gold in the belt of volcanic and sedimentary rocks extending eastward from the Porcupine and Kirkland Lake gold-fields has caused a great deal of excitement in mining circles. The area is heavily drift covered, and every aid to the location of veins is eagerly grasped. A knowledge of the physiographic history of the area is of the utmost importance in the application of many of these aids. Evidence is presented to show that glacial erosion has lowered the general elevation very little below the pre-glacial level, and that many glacial erratics have been carried less than three miles southward. Probably a knowledge of the general geology of a: region was never more necessary to the understanding of the distribution and continuation in depth of the mineral veins than in this area. Four distinct granites occur in the region, and gold-bearing veins are genetically associated with only one of these. Two types of quartz-feldspar porphyries have been found, only one of which has any bearing on the locus of the mineral veins. Many other examples of this complexity of associations might be cited, but everyone goes to show that in most cases the economic importance of the deposits can be realized only after the regional geology is understood. A series of sandstone, limestone and shale intruded by granite lies unconformably below the Keewatin lavas. The latter are intruded by a gneissoid granite and are overlain unconformably by the thick series of Timiskaming greywackes and silts. These are intruded by carbonated syenites and syenite porphyries which have since been rendered somewhat schistose.

Jan 1, 1927

By S. A. L. Read

"The intact rock constant, mi, is one of the three basic input parameters required for the widelyused Hoek-Brown failure criterion. Values for the constant should ideally be determined by statistical analysis of laboratory test data. In this paper the influence of the inclusion or exclusion of tensile test data on derived values is discussed. We firstly investigate the relationship between direct tensile strength (DTS) test values and Brazilian tensile strength (BTS) test values based on a literature search, finding that the correlation between the two test types is DTS = 0.9*BTS, independent of the lithology being tested. Secondly, using the shear strength database of Douglas (2002), we examine the influence of confining pressure range and the inclusion or exclusion of DTS and BTS test values on calculated values of mi.Chief amongst the influences was the exclusion of tensile data in the calculation procedure, particularly when the Hoek triaxial confining stress range requirement (?3?max = 0.5?c) was not satisfied. Based on a reasonable 1:1 relationship between R (the ratio of unconfined compressive to tensile strength), use of actual tensile data in the calculations for the Hoek brown failure criterion is considered to be a simpler and more robust approach to the use of a tensile cutoff based on empirical criteria such as that of Fairhurst (1964). We advocate the fitting a failure curve using compressive and tensile test data as the most reliable means of calculating mi, while at the same time satisfying requirements as originally advocated by Hoek relating to the appropriate triaxial confining stress range (?3?max = 0.5?c) and sufficient (>5) evenlyspread data points. In the absence of triaxial data the use of R provides a practical means of obtaining estimates of mi that are more robust than guideline values."

Jan 1, 2015

By S. G. Enns, E. W. Yarrow

"Situated about 200 km southeast of Juneau, Alaska, within the lower Stikine River region of northwestern British Columbia, the Galore Creek porphyry Cu-Au deposits are hosted by Upper Triassic to Lower Jurassic alkaline volcanic rocks and comagmatic syenite intrusions. Early and late breccias are also locally important host rocks for mineralization. Of the twelve identified Cu-Au deposits, the most important are the Central zone, Southwest zone and the Junction deposits with a combined resource of 284 million tonnes at 0.67 % Cu.The composition of the intrusive rocks is predominantly silica-undersaturated, alkaline, and metaluminous. Four intrusive suites are identified from field, petrographic and petrochemical data. Variation within suites or lineages can be explained by alkali feldspar fractionation. An oscillation between porphyritic and equigranular intrusions is suggested by the sequence of different intrusive lineages. The youngest intrusive phase is silica-saturated.A complex succession of intrusive and hydrothermal events is demonstrated at Galore Creek, with the most intense alteration and mineralization developing early in its history. In the Central zone, early Ca-K-silicate alteration, dominated by garnet, biotite, Kfeldspar, and anhydrite grades outward into K-silicate alteration. Both are locally overprinted by retrograde sericite± anhydrite± carbonate (SAC) alteration. The most intense Ca-K-si/icate alteration, a magmatic-hydrothermal breccia, and an early syenite intrusion are all coincident with copper mineralization in the core region of the Central zone. However, higher grade mineralization in the zone, exceeding 1 % Cu with more than 0.5 g/ t Au, is typically associated with intense biotite-rich, K-silicate alteration primarily hosted by altered volcanic rocks. The highest gold grades, commonly exceeding 1 g/t, are associated with bornite-rich mineralization situated in the northern and southern parts of the Central zone.Mineralization in the Southwest zone occurs as disseminated chalcopyrite within a late, diatreme breccia and adjacent K-feldspar porphyry. In the other satellite deposits, disseminated chalcopyrite and bornite occur in volcanic rocks with alteration that is similar to the Central zone."

Jan 1, 1995

By F. McCarthy, R. McDonald, G. Woodbridge, G. Brock, D. Robinson

"The Direct Nickel process is a hydrometallurgical technology being developed to treat nickel laterite ores by leaching at atmospheric pressure. The leaching process uses nitric acid in a relatively large excess, is thus non-selective, and much of the soluble iron goes into solution. The first stage of solution purification is iron hydrolysis and the Direct Nickel process utilises the colligative properties of the pregnant leach solution (PLS) to enable the removal nitric acid of varying concentrations via distillation. Once sufficient acid has been removed, the boiling point of the solution is increased allowing high temperatures (up to ~170°C) to be achieved under atmospheric pressure. The higher temperatures initiate the precipitation of the iron primarily as hematite and allow the removal of the acid generated by the hydrolysis reaction. The rejection of the iron is near complete with solution tenors typically falling from 65 g/L Fe, or more, to less than 50 mg/L Fe. The separation of clean nitric acid from the PLS at this stage allows for relatively simple acid recycling. A hematite product with iron content above 60% could also provide an extra revenue stream.INTRODUCTION The Direct Nickel (DNi) Process is a novel hydrometallurgical processing route designed to treat all types of nickel laterite ores in a single flow sheet using nitric acid under atmospheric conditions. A simplified flow sheet is shown in Figure 1.Between 2007 and 2012 the process was developed and refined at Direct Nickel’s laboratory within the CSIRO Minerals’ facilities in Perth, Australia, and in 2013 a series of pilot plant trials were run under continuous operating conditions. The process is designed to treat both limonite and saprolite in the same flow sheet, and after comminution, the blended ore is mixed with nitric acid and leached just below boiling point in agitated atmospheric leach tanks. The acid is added in excess, so typically for a blend of limonite and saprolite the acid addition can be in the order of 1.8-2.0 t acid/t dry ore. After a residence time of between 4-6 hours the majority of the soluble metals have leached into solution and the insoluble leach residue is separated from the pregnant leach solution (PLS) via counter-current decantation."

Jan 1, 2016

By G. B. Harris, C. W. White

Cyanide has been used for the recovery of gold since the mid 1800s, but several jurisdictions have already banned its use, and environmental pressures are increasing to finding an alternative. Gold also forms chloride complexes similar to those of cyanide, but the use of chloride has never achieved widespread acceptance. This paper describes a chloride-based flowsheet, wherein the key unit process is the recovery and recycle of chloride ion. It is shown that the chloride-based flowsheet is competitive economically with the conventional cyanide-based flowsheets, and that it has a number of other advantages, particularly environmentally.

Jan 1, 2011

By S. Flewelling, M. Scobie, G. R. Baiden

"SynopsisA feasibility study to develop a research program, the Mine Automation Plan (MAP), was recently completed. This was undertaken by a team comprised of Inco Ltd., Falconbridge Limited, the Canadian Centre for Automation and Robotics in Mining (CCARM) and the Centre for Resource Studies (CRS). The study was sponsored by PRECARN Associates, which is a consortium of thirty-six Canadian companies focussed on research and development in artificial intelligence and robotics. PRECARN Associates was formed in 1987 when a number of research proposals were funded in the fields of process control systems, robotics systems and intelligent engineering systems. In July 1991, PRECARN accepted the next round of proposals for research. The MAP project was one of the successful proposals, being awarded $100,000 for the development of a feasibility study defining a long-term R&D plan for underground hardrock mining automation.The development of the feasibility study started by addressing the fundamental structure of the mining process, and its relationship to the metallurgical process, over-all infrastructure support and management systems (Fig. I).Mining may be considered as comprising five subprocesses: (I) delineation; (2) development; (3) production; (4) backfilling; and (5) infrastructure support services. Within these subprocesses many applications for artificial intelligence and robotics exist. The mining process is dependent upon the interaction between the physical mining process and information. For example, the delineation process is dependent on geomechanical, geochemical and geophysical techniques to develop a model of the orebody based upon access to such data. This same relationship between the physical and information models holds true through the development, production, backfill and infrastructure support systems.The foundation for the MAP study has been the recent development by Inco Ltd. of an underground communications system (Fig. 2). The system has the ability to supply high bandwidth communications, over voice, data and video to mobile and stationary locations within the mining operation. It is seen to be the future backbone of a comprehensive, automated information system which should permit the application of the concept of Computer Integrated Manufacturing (CIM) to underground mining. CIM, through the automated flow of information, has been successful in integrating the engineering, production and various support groups in manufacturing."

Jan 1, 1994

By Edgar Stanfield

Since April, 1923, the Scientific & Industrial Research Council of Alberta has had an analyst, Mr. W. P. Campbell, steadily employed analyzing coal samples taken by the provincial Mine Inspectors. Mr. Campbell has also analyzed a number of coal samples taken by one of the Council's Geological Survey parties. We have thus, at the time of writing, over four hundred analyses of Alberta coal, made by the same analyst, and strictly comparable. These samples come from widely distributed points, some 88 townships being represented. The stream of samples is still flowing in, and it is hoped by the end of this year that the number of townships represented will be increased at least fifty percent. The time has arrived to publish some of the data collected; but it must be clearly understood that this is merely a progress report, subject to revision as further information is obtained. Three hundred and fifty-three coal mines in the province were operated during 1923. The production per mine varied from 5 up to 500,000 tons. With this number of mines to examine (and fresh mines are being opened every year) it is a large task to make even a proximate analysis of representative samples from every mine. Any chemist will appreciate the fact that to make ultimate analyses representative of even the larger mines will be a long and tedious task. It has seemed better to make a comprehensive survey by proximate analysis and determination of calorific value before beginning the more thorough survey by ultimate analysis. This paper, therefore, deals only with proximate analyses and calorific values; and, owing to limitations of time and space, does not deal with other chemical and physical characteristics of coal, such as storage quality and fusibility of ash, important though these are.

Jan 1, 1925

By w. w. Fraser

"In late 1985, Hudson Bay Mining and Smelting Co., Limited announced the Namew Mine/Mill project. Environmental baseline monitoring and planning began in early 1985 while a major drilling program was under way to delineate the ore deposit. This paper overviews the environmental assessment work conducted for the mine/mill operation, and outlines the tailings and water management practices.Planned environmental works and approach were affected in late 1988 when a massive water problem was encountered in the mine. The requirement to depressurize the rock surrounding the underground workings led to the need to develop, on short notice, an environmentally-acceptable procedure to dispose of a large volume of slightly-saline water.Biological toxicity tests performed on the depressurized effluent proved the effluent to be non-toxic and thus allowed resolution of the disposal problem. This resolution includes the conversion of a large water body from native fish species to a rainbow trout fishery."

Jan 1, 1991

By Robert B. Parsons

"Originally intended to be implemented in 1977, but actually introduced effective May 6, 1974, the earned depletion regulations have been substantially refined and modified since their appearance on the Canadian tax scene, so that this important legislation now consists of a highly complicated set of rules which even the most astute follower of tax law has considerable difficulty sorting out!This month, Tax Notes attempts to cut through this bewildering array oj regulations, in reviewing the main features of the earned depletion allowance applicable to mining operations. Despite the phase-out of earned depletion allowances for most oil and gas operations as part of the federal government's new National Energy Program, earned depletion provisions are still alive and well for the mining sector, although they might well be slowly strangling to death in their own entanglement of complexity!"

Jan 1, 1981

By G. F. Carr

"IntroductionFLUORSPAR has been found at several •localities in Newfoundland, but all the commercial deposits discovered to date are in the vicinity of St. Lawrence, a town on the southeast coast. Most of the veins are within six miles of St. Lawrence harbour, and between sea-level and an altitude of 400 feet. The St. Lawrence Corporation of Newfoundland, Limited, and Newfoundland Fluorspar, Limited, a subsidiary of the Aluminum Company of Canada. Limited. are the two producers.With the arrival of 1953, the St. Lawrence area entered upon its twenty-second •consecutive year as a producer of fluorspar. Production has increased more or less steadily during this period, as is shown by the fact that approximately one-half of the total shipments to date have been made during the past six years. Between four and five hundred men are employed by the industry, and more than $1,250,000 was paid out in wages and salaries during 1952. Shipments during that year reached an all-time high of 81,283 tons valued at $2,484,943, compared with 67,925 tons valued at $1,966,477 in 1951 (1).As a result of an agreement made in July, 1952, with the United States Defence Materials Procurement Agency, production of the St. Lawrence Corporation, Limited, and St. Lawrence Fluorspar, Incorporated, an affiliated company, will •be increased by .approximately 50,000 tons of acid-grade fluorspar per year. The contract extends over a period of four years, or until 150,000 tons of acid-grade concentrates have been produced."

Jan 1, 1954

By V. J. Southey

HOLLINGER mining operations have required development by 24 vertical shafts having a total length of 28,160 feet. Seventeen of these are sunk from surface and seven are interior shafts. Four surface shafts and three interior shafts are now active and, excepting the recently completed new main ore-hoisting shaft, the remainder are either abandoned, or are used for passes or for ventilation. The new shaft bottoms 60 feet below the 3,050 level, but there is much work to be done before it is placed in service. The term 'shaft practice' is intended to include shaft construction and a general treatment o typical equipment. It is a large subject for an organization the size of Hollinger and this paper is intended only to present the salient features. The writer wishes to thank the management for permission to publish this information and to acknowledge the advice and criticism o A. G. Irving, chief engineer, and the willing co-operation of other members of the Hollinger staff.

Jan 1, 1939

By Claudia Gasparrini

"Factors affecting the extraction of gold are of a mineralogical nature. Knowledge of the mineralogy of the ore or metallurgical product to be treated, if appropriately combined with the metallurgical test work, may improve gold recoveries. .This paper outlines the mineralogical techniques f or the study of gold ores and metallurgical products and describes the gold mineralogy in relation to its metallurgy. An effective plan for studying refractory and other difficult ores, combining metallurgical test work, chemical analysis and mineralogy and capable of giving positive results over relatively short periods of time, is suggested.IntroductionFactors affecting gold recoveries are of a mineralogical nature and include (i) the gold-bearing minerals, (ii) their grain size and, particularly where the grain size is very fine (10 microns in diameter and less), (iii) their host minerals and (iv) the association these form with the gold-bearing minerals.Mineralogical studies of gold ores and metallurgical products containing gold in economic amounts (today down to 1/10 of one ounce per tonne or 2.84 ppm) are difficult and time consuming. Mostly because of such reason, metallurgical testing (test work) is usually done simply by trial and error without understanding the causes for failure or success.Mineralogical studies, if appropriately conducted and combined with the test work, provide an efficient mean s of improving recoveries through the understanding of gold losses derived from the use of the wrong technique for separation. The information they provide is therefore the first step in the development of recovery techniques, for those ores where the test work alone failed to produce positive results."

Jan 1, 1983

By H. R. Butler

"The Ontario Division of Inca Metals Company, a Unit of Inca Limited, operates eleven mines, four mills, three refineries, one smelter and one iron ore recovery plant. All but one mine, mill and refinery are located within a fifty kilometer radius of Sudbury, Ontario. A mine-mill complex is located some 100 kilometers west of Thunder Bay on the shore of Lake Shebandowan and a nickel refinery at Port Colborne.During the past 10 years the use of recycled water in our milling operations has increased to more than 95% at each mill. This high degree of water reuse has reduced the (a) need for fresh water and (b) the contaminant level of the downstream aquatic environment. The aggregating of effluents in a common receptor provides a process water having a consistent quality thereby minimizing upsets in mill metallurgy while concurrently improving the operating economies and the downstream aquatic environment."

Jan 1, 1980

By A. J. Monhemius

This paper reviews the history of modern iron-control processes in hydrometallurgy. Attention is paid to processes developed in the electrolytic zinc industry for removal of iron from zinc sulfate leach liquors and the problems faced by the industry in the safe disposal of the iron residues produced by these processes. Past lessons learned are projected onto current efforts to develop hydrometallurgical processes for treatment of copper sulfide concentrates. It is argued that any attempt to create a \u201chydrometallurgical copper smelter\u201d will fail, unless methods are developed that can recover iron in a form that can be directly used by the steel or pigment industries.

Jan 1, 2017