Search Documents

By P. H. Agson Gani, T. Sitorus, N. P. Widodo

"PT ANTAM UBPE Pongkor underground mine use blasting to develop its tunnels which will cause poisonous and dangerous gases trapped inside mine. To analyze this case, a study of mine ventilation, the dispersion of carbon monoxide (CO) gas concentration and diffusion coefficient is commenced. At the end, the re-entry time formula will be determined. Results indicate that this study is site specific and could only be applied in the place this study executed. The aim of this study is to be further developed by applying Principal Component Analysis (PCA) to find a universal re-entry formula. KEYWORDS Mine Ventilation, Re-Entry, Smoke Clearing, Diffusion Coefficient, Carbon Monoxide Gas, Gas Dispersion INTRODUCTION Pongkor underground mine is using cut and fill as its mining method. Thus, its development and production processes require blasting to develop its tunnel. This process caused poisonous and dangerous gases spread and trapped inside the mine, one of them is carbon monoxide (CO) gas. CO is formed in an unbalanced reaction of explosives detonation and could be the cause of headache, blackout and death to people who inhale CO at certain concentration (McPherson, 2011; Hartman, Mutmansky, Ramani, & Wang, 2012). Mine ventilation system is installed in the mine to resolve this problem. Mine ventilation play an important role to disperse CO gas by absorb the poisonous/dangerous gases and deliver clean air into mine. The important parameter is diffusion coefficient, because diffusion is affecting particulates or gasses spreading from its sources throughout the mine. Diffusion coefficient is the total diffusion in axial direction of turbulent flow mainly by convection of bulk motion, advection and eddy diffusion, while the effect of molecular diffusion is appreciably negligible (Widiatmojo et al, 2015). Taylor (1953, 1954) develops a theory about the dispersion by inducing a slow stream of solvent into a capillary tube. Taylor used Reynolds assumption of radial diffusivity to be analogous with the transfer of the matter in turbulent flow as well as the transfer of momentum and heat. Then, Taylor proposed the formula of diffusion coefficient, D (m2/s), against pipe diameter and turbulent shear velocity are as follow:"

Jan 1, 2019

By Ron Light, Doug Applett

"HistoryThe Nanisivik mine began operation in October 1976 as the world's most northerly metal mine and the first permanent industrial project in the Canadian High Arctic. Located 700 km north of the Arctic Circle on Baffin Island's Strathcona Sound, exploration by Texasgulf Inc. between 1957 and 1970 had outlined the ore deposit. In 1974, Nanisivik Mines Ltd. was formed with Mineral Resources International, the Government of Canada, Metallgesellschaft and Billiton being shareholders, and Strathcona Mineral Services Ltd. providing project management. In 1996, Breakwater Resources purchased the mine from Alberta Energy Corporation Limited which had recently acquired the assets of then owners Conwest Exploration Ltd.Ore DepositThe main ore deposit is very flat, approximately 80 m in width and varying in thickness from 3 m to 16 m. The length of the deposit is approximately 3000 m with satellite zones located on the perimeter of the main zone. The economic mineralization is sphalerite with minor galena and silver. The sphalerite and galena are coarse grained and associated with pyrite as the main gangue component with minor inclusions pf dolomite and calcite within the deposit. The deposit being hosted in a permafi·ost environment creates a number of challenges. Dry drilling is employed in room and pillar production drilling. The permafrost aids in the stability of both the pillars and the back."

Jan 1, 2000

By M. Kawahara, H. Sunayama

Oxidation rates of the cubic specimens, which were prepared by cutting the shaped magnesia-carbon bricks, were measured continuously with a thermo balance in the temperature range from 1273 to 1 823 K in N2-02 and Ar-02 mixed gas with 2.1 x 104 and 3.7x 102 Pa of oxygen partial pressure respectively. The effect of the graphite content, the maximum grain size of magnesia clinker and the oxygen concentration in the atmospheric gas on the oxidation rate for the MgO-C refractory has been investigated. The value of effective diffusion coefficient of O2, which diffuses through the porous decarburized layer, decreased with the decreasing of the porosity and the oxygen concentration in the external gas phase. It was speculated that the dense layer formed easily due to the high tortuosity of pores and the low recession speed of the carbon interface in the MgO-C bricks.

Jan 1, 2004

"Accelerated expansion of Western Canada's metallurgical coal industry has again stimulated considerable exploration activity in the Rocky Mountain Foothills Belt and influenced much of the R&D related to transportation, processing and carbonization. Preparation R&D has included further pilot-plant work on desulphurization, spherical agglomeration and modified compound cyclones (which are also proving themselves in other mineral beneficiation studies). Combustion research, aside from increasingly stressing control of combustion source pollution, has directed special attention to lignite PF firing and problems arising from lignite ash. Studies directed toward the non-fuel utilization of coal have centered on such diverse topics as active carbons, carbonaceous filter media, plant nutrients and industrial applications of humic acid derivatives. In addition, a number of long-range research projects related to such matters as coal chemistry and pyrolysis have been actively pursued, and further attention has been given to improved sampling techniques and analytical methods."

Jan 1, 1969

By Chris Twigge-Molecey, John Peacey

To meet the business objectives of a metallurgical project, there is often a need for new and untried technology or equipment, whose very novelty can present serious risks to meeting those objectives. The key risk management approach is a rigorous stepwise progression from theoretical evaluations and laboratory tests to pilot plant trials. These must be followed by demonstration-scale trials before final construction of a commercial scale plant, paying particular attention to the magnitude of the scale-up between phases. Success depends on following a well-defined program, not eliminating any steps, and ensuring adequate resources are available to the development team. Chapter 6 discusses the nature of technology risks to metallurgical plant projects, and the rigorous management practices needed to identify, analyze, evaluate, and avoid or mitigate them.

Jan 1, 2015

By E. Uzun

"In this study, H2SO4 and HCl leaching behaviour of an ore sample containing 1.87% of Ni, obtained from the Karaçam (Eskisehir-Turkey) lateritic deposit that started operation recently was investigated. Acid concentration, temperature and reaction time were investigated as variables by comparative leaching tests and the optimum leaching conditions were selected on teh basis of Ni, Fe, Co and Mg behaviour. For H2SO4 leaching, optimum leach parameters were 95°C, a 12 normal H2SO4 concentration and 90 minutes of reaction time, and under these conditions Ni and Fe dissolutions were 97.6% and 95.4% respectively. On the other hand, 70°C, an 8 normal HCl concentration and a reaction time of 90 minutes were found to be the optimum parameters for HCl leaching, and Ni and Fe dissolutions found were 97.1% and 97.8%, respectively.INTRODUCTION Today, nickel and various nickel compounds are obtained from sulphide and lateritic nickel ores (Moskalyk & Alfantazi, 2002). Even though about 72% of the world's nickel reserves constitute lateritic ores, only about 42% of nickel is produced from these ores. The decrease in production from sulphide deposits, on the other hand, and increases in the use of nickel in the iron and steel, and battery production sectors, and especially the production of nickel cast irons in recent years, have accelerated the importance of making use of lateritic deposits (Luo et. al., 2010; Chang et. al., 2010). In the beneficiation of sulphide nickel ores, mostly pyrometallurgical methods are used. On the other hand, about 39% of lateritic ores are beneficiated by pyrometallurgical, and 61% are beneficiated by hydrometallurgical methods (USGS, 2009). In laterite beneficiation, the ore properties are of significance; that is to say, limonitic ores are eneficiated by high pressure acid leaching or via the Caron process, nontronitic ores are beneficiated by high pressure acid leaching or heat treatment (smelting), and ores containing serpentine by pyrometallurgical methods (Berezowsky, 2004; McDonald & Whittington, 2008a; Dreisinger et. al., 2015)."

Jan 1, 2017

By Xiaowen (Wendy) Ma, Hans Liang, Xiaoying Chen, David Way

"The mineralogical characteristics of the process streams provide key indicators to the potential improvement in the metallurgical performance. Therefore, the process mineralogy and diagnostic metallurgy have been widely used as a tool to assist the metallurgists at the operating plants. The challenge of this study was then how to characterize the diagnostic flowsheet of the minerals of interest in the process streams across the flotation circuit. The investigation from this study indicates that the minerals chematic flowsheet can visibly demonstrate the sources that caused the gold losses during the mineral processing.In this paper, we present studies of the flotation process stream samples, representing the feeds, intermediate products, final concentrate and final tails, which were produced from the flotation concentrators of Mt Carlton mine in Queensland, Australia. This study was focused on characterizing the process streams and learns how the gold in the process streams was associated with other sulphide minerals and host minerals on a size by size basis. The automatic QEMSCAN/MLA Particle Mineral Analysis (PMA) and Trace Mineral Search (TMS) were applied to identify the minerals and to detect the gold in the sized fractions of process streams. The Laser Ablation ICP-MS (LA) spot analysis, QEMSCAN EDS spot analysis and electron microprobe spot analysis were employed to identify and quantify there fractory gold concentrations in the sulphide minerals, like pyrite, and the elemental concentrations of visible gold grains. The diagnostic flowsheet of gold recoveries by the process streams, by mineral association classes and by the particle sizes were generated and discussed."

Jan 1, 2017

By A. K. Mahto, B. Samanta

"A heuristic model was developed to simultaneously generate the ultimate pit and production scheduling at a mining project. The method consists of a preprocessing step to select a starter pit, the implementation of a genetic algorithm to optimize the pit and schedule of the starter pit, and a network-flow algorithm–based postprocessing operation to finalize the ultimate pit and production scheduling. Applied to an iron ore mine, the model pit and schedule produced a net present value 21% higher than the reference pit and schedule prepared by experienced field engineers.RÉSUMÉ Un modele heuristique a ete developpe pour generer simultanement l’ordonnancement de la fosse finale et de la production dans le cadre d’un projet minier. Cette methode comprend une etape de pretraitement visant a selectionner une premiere fosse, la mise en oeuvre d’un algorithme genetique pour optimiser la fosse et le calendrier d’execution de cette premiere fosse, ainsi qu’une operation de posttraitement basee sur des algorithmes de flux reseaux pour finaliser l’ordonnancement de la fosse finale et de la production. En l’appliquant a une exploitation de minerai de fer, ce modele de fosse et d’ordonnancement a genere une valeur actualisee nette (VAN) superieure de 21 % a l’approche de reference pour la fosse et l’ordonnancement developpee par des ingenieurs de chantier chevronnes. INTRODUCTIONLong-term planning for an open-pit mine involves two important activities: developing the ultimate pit and determining the optimum production schedule. To accomplish this, an ore deposit is discretized into a number of smallsized elements called blocks, which are presented in a 3D block model structure. Because of economic and slope criteria, only a certain set of mining blocks can be extracted from the deposit constituting a pit. During mining, these blocks must be extracted in a specific sequence known as the production schedule."

Jan 1, 2017

By H. W. Parsons

Several low-temperature, dry chlorination processes for the treatment of sulphide minerals are reviewed, in a chronological order. These processes include the following: the Swinburne-Ashcroft, Baker-Burwell, Maim, Comstock-Wescott (Aldermac) and the Mitterburg Mining Process. Dry chlorination investigations at the Canadian Mines Branch (now CANMET) and the U.S. Bureau of Mines are discussed, as is a proposed process by the South Africa National Institute for Metallurgy. The techniques used in the process are discussed, as are the shortcomings, problems and failures of the methods.

Jan 1, 1978

By Werner Unland, Nick Holl

"The paper presents the engineering design and experience gained so far with a dewatering system for an open-pit uranium mine planned at Key Lake in Northern Saskatchewan.The results of hydrogeological investigations preceding engineering exhibit an extensive unconfined overburden aquifer hydraulically connected with the underlying Athabasca Formation and basement rocks, both of relatively low hydraulic conductivity. The overburden aquifer is embedded in a bedrock trough, with the deepest depression between the planned pits. The hydrogeological data were used in a numerical dewatering model simulating groundwater flow atdifferent stages of the pit development.Based on the model results, the engineering design had to provide for different pumping rates, varying between 1.0 and 0.21 ms/sec. This problem was solved by using a double line pressure system. The design concept for the complete peripheral discharge system and the well design used for 26dewatering wells are discussed.Experience with reverse-circulation techniques applied for the construction of the dewatering wells is presented. Theoretical and practical considerations which led to the constructionof wells of different diameters are discussed.The design of the in-pit dewatering system provides for seepage ditches, horizontal drains, pit-bottom sumps and inpit dewatering wells where required."

Jan 1, 1980

By W. D. Madeley

Synthetic minerals were made from pure starting materials and galena samples were doped with the title metals. Microscopic, microprobe and X-ray examination confirmed that the dopeants were in solid solution. Paired flotations in a Hallimond-tube apparatus were performed to determine relative flotation response using Aerofloat 238 promoter. Results of these tests show that silver-doped galena floats more readily than pure galena and that galena doped with bismuth floats less readily than pure mineral to a 95% confidence level. Galena doped with both silver and antimony as AgSbS2 shows no detectable effect. Antimony-doped galena followed the expected trend, but not to 95% confidence. The results are consistent with the theory that flotation by thiol-type anionic collectors is enhanced by p-type semiconduction.

Jan 1, 1978

By Peter Cunningham

Teck Facts and Figures ? Employ more than 14,000 around the world, includes: ? Over 8,600 in Canada (close to 7,800 in British Columbia) ? Close to 2,000 in Chile ? Over 2,700 in Peru ? Approximately 600 in U.S. ? Hundreds more in exploration around the world ? Total capital expenditures ? $1.8 billion for 2012

Aug 1, 2013

By H. Huang, H. M. Chen, W. B. Xie

Cu-0.8Cr-0.1Zr alloy were prepared by atmospheric melting. the microstructure and properties of the CuCrZr alloy after first cold rolled, solid solution, second cold rolled and aging treatment were analyzed by using optical microscope, electrical conductivity analysis and Vickers hardness tester. The results show that with the increase of the first cold rolled deformation, the grain breakage becomes more serious, and the cold hardening becomes more obvious and the hardness increases. The conductivity and peak hardness of the first cold rolled (reduction of 30% and 60%) alloys after solution, secondary cold rolled and aging treatment reaches 81 %IACS and 187 HV, respectively. However, the conductivity in the CuCrZr alloy with a higher rolling degree (reduction of 90%) after solution, secondary cold rolling and aging treatment is significantly higher, and the conductivity and peak hardness is 85.8 %IACS and 178 HV, respectively. INTRODUCTION CuCrZr alloy has been widely used in domestic industry for its excellent comprehensive properties such as high strength and high conductivity, especially in the contact wire and lead frame of high-speed railway (Sun, Tao, & Lu, 2015; Mishnev, Shakhova, Belyakov, & Kaibyshev, 2015; Zhang et al., 2016; Fu et al., 2017). In recent years, a lot of research has been done on how to improve the strength and conductivity of CuCrZr alloy. However, the high strength and high conductivity of copper alloys are contradictory characteristics. On the one hand, the addition of alloying elements is conducive to solution strengthening and aging strengthening; on the other hand, too much alloying elements in copper alloys cause defects in the lattice of copper matrix, resulting in a serious decline in the conductivity of copper alloys (Martienssen & Walirmont, 2005). How to obtain high strength and high conductivity at the same time is the main problem. At present, the main research methods are adding microalloying elements, thermomechanical treatment and severe plastic deformation to study the electrical conductivity and mechanical properties of CuCrZr alloys. For example, Xie et al. (2011) added trace Ag to the Cu-0.26 wt%Cr-0.08 wt%Zr alloy, and the size of precipitated phase Cr and Cu4Zr became smaller and the mechanical properties of the alloy were improved. Su, Dong, Liu, Li, & Kang (2004) found that the addition of trace Mg in CuCrZr alloy inhibits the growth of precipitated phase and reduces the internal stress around the precipitated phase. At the same time, the size of precipitated phase becomes smaller and the peak aging strength of the alloy is improved. Pang et al. (2013) found that adding trace Ni and Si to the CuCrZr alloy could improve the peak hardness, softening resistance and precipitation morphology of the alloy. Experiments shows that the grain size was significantly refined by equal channel angular extrusion combined with aging treatment, while the strength of the alloy was increased, and the electrical conductivity of the alloy did not decrease (Vinogradov, Patlan, Suzuki, Kitagawa, & Kopylov, 2002; Saray, 2016); Kermajani, Raygan, Hanayi, & Ghaffari (2013) showed that the strength of CuCrZr alloy can be improved by rolling at 500 °C. After 150 minutes of aging treatment, the strength and conductivity of the material increased to 431 MPa and 81 %IACS, respectively. Takata, Ohtake, Kita, Kitagawa, and Tsuji (2009) noted that the strain hardening, uniform elongation and tensile strength of the nano-precipitates produced by the mechanical heat treatment process can be notable enhanced. The mechanical and electrical properties of CuCrZr alloy can be improved by combining large plastic deformation with aging treatment in the test process (Gao, Huttunen-Saarivirta, Tiainen, & Hemmila, 2003; Huang et al., 2003; Xia et al., 2012; Zel’dovich et al., 2014).

Jan 1, 2019

By Victor R. Eyzaguirre

Cerro Verde is one of several large porphyry-type copper deposits in Southern Peru. The copper occurs as primary sulphides, with a significant oxide capping. The exploitation of the deposit has been correspondingly divided into two stages, the first consisting of copper production from oxides, and the second from sulphides. Minero Peru successfully started the Stage I plant in June of 1977 with the first production of electrowon copper cathodes. This paper is essentially devoted to a description of the Stage I process, which can be summarized as follows: Ore is trucked to the primary crusher, where it is crushed to 225 mm and conveyed to a coarse ore stockpile. Ore withdrawn from the stockpile is secondary crushed to 65 mm, conveyed to a truck loadout bin, loaded into trucks and driven to the leaching pads. Ore is placed on the pads in lifts and sprayed with sulphuric acid solution to dissolve the copper. Copper-bearing solution forms a pond behind a dam at the lower end of each pad and is pumped from there to the solvent extraction plant. Copper is extracted from the leach solution into an organic phase and is then stripped from the organic phase to form a purified concentrated copper solution suitable for feed to electrowinning. In electrowinning, the copper is finally recovered as cathodes suitable for sale as refined copper.

Jan 1, 1978

By J. M. Whiting

"North America has entered a period when greatly increased attention must be given to energy .supply and demand by government, industry and individuals. Such increasing concern about energy will be a long-term phenomenon, accompanied by continuing examination of future resource development and utilization. Those engaged in or associated with mining, a major energy consumer, are likely to experience a variety of problems which are associated with the end of an era of low-cost, virtually unlimited energy supply. Their efforts, furthermore, may be subjected to escalating public and government scrutiny, involvement and control. However, ever-growing recognition of the real and urgent necessity to systematically develop new energy supplies within Canada and the United States will provide unusual challenges and opportunities for those companies and individuals with mining expertise. The vast deposits of coal, tar sands and oil shale provide a relative certainty of supply which only stands to gain in attractive ness with time. In order to benefit from this aspect of certain supply, nevertheless, synthetic fuels will have to be produced at a tolerable cost. This will always require excellent process design and engineering. As synfuels development expands to any significant production level, however, and Jess than ideal reserves are scheduled, the usual geologic-productivity complexities encountered in making ore out of low-value rock will tend to become of prime concern. It is for this reason that the services of experienced mining personnel will be in growing demand in energy production."

Jan 1, 1973

By C. Jay Hodgson, P. J. MacGeehan

"The gold ore zones of the Campbell and Dickenson mines occur within a km-wide, 2 km-long zone of highly altered and anomalously fissile and deformed volcanic and subvolcanic intrusive rocks, cut by a series of mainly post-deformation mafic and quartz-feldspar porphyry felsic dykes.Three main periods of gold ore-forming hydrothermal activity are recognized. In the first, the mine rocks were extensively altered and gold and arsenic enriched; syn-volcanic auriferous veinlet and low-grade chemical sedimentary ores were deposited in what was a major discharge zone of a submarine hydrothermal system. The chemical sedimentary ores are closely associated spatially and temporally with domal rhyolitic extrusions. Because of its mechanical and chemical properties, this synvolcanic alteration zone became the locus of later deformation, and the site of the generation of auriferous hydrothermal solutions, perhaps by pressure solution processes at depth. These solutions deposited, synchronously with deformation and metamorphism, the second and most economically important type of ore zones in the mine: large foliation-parallel and foliation-oblique banded carbonate- 'chert' Rssure-filling veins.In the third and final mineralizing event, high-grade, pipeshaped zones of siliceous replacement-type mineralization, and quartz-arsenopyrite-gold veins, were superimposed on the previous mineralization types after most of the deformation, but before the emplacement of the late dykes. The source of heat and also possibly the fluids for the third mineralizing period may have been the dyke-forming igneous activity. The textures and mineralogy of the banded carbonate- 'chert' veins suggest a near-surface (<3 km) environment of deposition, but their relationship to the fabric of their host rocks indicates they were emplaced in an environment, presumably at considerable depth (5-10 km?), in which the rocks were undergoing intense penetrative deformation. This anomaly is unresolved."

Jan 1, 1982

By C. M. Offenhauer

Abstract Zirconium markedly affects the formation of graphite in cast iron and may promote the formation of normal flake gaphite, fine flakes of eutectiform graphite, or spheroid nodular graphite, according to the composition of the Iron and the amount of the zirconium addition. Usually, it is employed in the form of a complex addition agent in order to facilitate its introduction and to guide its effect. The reported applications of zirconium as an inoculant for the production of pearlitic high-strength cast iron indicates that it is most effective as a silicon-manganese-zirconium alloy. Added in this form it reduces chill and minimizes zones of ferrite and eutectiform graphite. In low-sulphur cast iron, zirconium in amounts greater than 0.10 per cent tends to promote the development of eutectiform graphite. These irons are characterized by freedom from primary cementite or normal flake graphite and exhibit very little tendency to shrinkage on solidification. In hyper-eutectic low-sulphur cast iron, zirconium causes the formation of a partially nodular graphite structure. A combination of magnesium with silicon-zirconium alloy was found to produce completely nodular graphite structures without the hazards associated with the addition of elemental magnesium.

Jan 1, 1949

By J. W. Kramers, R. A. S. Brown

"Samples from seven test wells distributed throughout the surface-mineable area of the Athabasca Oil Sands have been evaluated to determine the amounts of heavy minerals present and the titanium and zirconium contents. The samples were treated to yield the size distribution of the titanium and zirconium minerals as well as their spatial distribution. The study has shown that heavy minerals are found throughout the surface-mineable area; concentrations range from 0.24 to 2.29 per cent (by weight), with a mean of 1.02 per cent. Titanium and zirconium contents vary throughout the area, and are found preferentially in the finer size fractions. •on the basis of preliminary calculations, the tailings streams from an oil sands plant would provide sufficient feed for a large-scale titanium pigment plant, and the tailings from one plant would provide sufficient zircon feed to satisfy Canadian demand for. metallic zirconium. Variability of the heavy mineral content and composition is such that the heavy mineral potential must be evaluated in detail for each mine site."

Jan 1, 1976

By Y. Yhang, D. C. Sego

ABSTRACT This paper evaluates the potential of freeze-thaw dewatering using Albian mature fine tailings (MFT). Freezing tests were first performed to study the effect of freezing rate on dewatering efficiency. Lower freezing rate resulted in higher thawed solids content and shear strength. Subsequently, large strain consolidation tests were conducted to investigate consolidation behaviour and how it is affected by freeze-thaw. The consolidation behaviour was presented in terms of effective stress versus void ratio and permeability versus void ratio. The results can be used to predict the field behaviour of Albian MFT and optimize the application of freeze-thaw for MFT dewatering.

Jan 1, 2014

"In many gold deposits, a reasonable amount of the gold that remains in the cyanide leach tailing is associated with pyrite. Some gold plants have found it economical to incorporate gravity circuits on the cyanide leach tailing to recover the gold bearing pyrite before subjecting it to fine grinding, then recycling the ground pyrite back to the cyanide leach circuit. For low grade gold deposits the loss of gold bearing pyrite is exacerbated as the broader process economics normally favour a coarse grind (> 150 ?m). An option that has received attention over the last decade is to recover the gold bearing sulphides in the milling circuit by gravity, similar to the widely-practiced gravity recovery of free liberated gold. The modelling and simulation of a gravity gold circuit in a milling flowsheet is relatively simple compared with a gold bearing pyrite circuit, as the recycle advantages and breakage functions for gold and pyrite are quite different. This current work represents an attempt to simulate the gravity recovery of gold bearing sulphides in a milling circuit that also incorporates fine grinding, using relatively simple simulation models. The simulation results are further explored with reference to the economics of this type of circuit.INTRODUCTION It is well known that gold is associated with pyrite in most sulphide gold deposits and that the amount of gold associated with pyrite will vary from deposit to deposit. Most of the gold associated with pyrite is liberated in the grinding circuit during the processing of a gold ore. However, some gold remains occluded in the pyrite and is lost in the final leach tailings. Little information is available in the literature on methods to enhance gold liberation from pyrite by specifically removing pyrite, either in the grinding circuit or from the final tailings stream, and grinding it finer. One of the earliest record of this approach is described by King (King, 1949) where pyrite present in Witwatersrand gold ores was recovered by circular jigs and Johnson barrels followed by fine grinding of the concentrate prior to cyanide leaching. Dominy et al., 1970, provides information on the use of Yuba jigs to recover pyrite from the discharge end of ball mills. Again, the jig concentrate was ground to a fine particle size before cyanide leaching to recover the liberated gold. Unfortunately, no information is provided in these articles on the additional gold recovery from implementing these circuits in a flowsheet. Martins et al., 1993, provides details of a gravity circuit using Reichert cones and spirals to recover gold bearing pyrite from a cyanide leach tailings followed by fine grinding of the pyrite concentrate in a Tower mill. The ground concentrate returned to the front end of the already installed leach circuit. Overall recoveries were increased by some 2% to 4% depending on the amount of gold and pyrite in the plant feed."

Jan 1, 2017