Search Documents

By H. Attia, S. Engin

This paper presents a practical approach for determining the optimal spindle speed and the depth of cut in a milling operation within the ever-increasing economic and technical constrains. Analytical modeling and experimental work has been carried out to predict chatter in such operations. The stability lobes determined from this analysis were then used as a constraint in the optimization of the cutting process. The optimal cutting conditions are determined for two different objectives: maximum metal removal rate and minimum cost per unit. It is demonstrated that this approach can be generalized to impose multi-level constrains, e.g., surface integrity and machining accuracy. The approach presented in this work was examined and validated on three NC milling machines. The productivity improvement, cost reduction, while respecting part quality requirements, is demonstrated.

Jan 1, 2006

By Q. Liu, P. Katsabanis, J. A. Meech

A thermohydrodynamic computer code has been used to simulate dust explosions. For sulphide dusts, the thermodynamic predictions are used to investigate the effect of dust concentration, mineral content and inert materials as well as the quantity of sulphur dioxide produced. It was found that the amount of oxygen available for the explosion is very important and that the dust concentration which gives maximum explosion pressures is obtained at zero or slightly negative oxygen balance values. The sulphide minerals were found to have the following explosibility sequence: pyrrhotite, pyrite, chalcopyrite, sphalerite, covellite, chalcocite and galena, which is in agreement with mine experience. The results show that theoretical calculations can be used to predict explosion pressures and toxic gases produced by a dust explosion and therefore they can assist in the design of protective measures .

May 11, 1988

By G. McIsaac

"This paper discusses the formulation of a linear program with the objective of maximizing the cash flow of the long-term plan of an underground operation. A mine is split into eleven independent ore zones, each characterized by its reserves, required development, and mining method. Based on practical considerations, maximum rates are set for each zone’s development and production capacity. For the total mine plan, a minimum daily production rate is set along with a minimum feed grade to the mill. A maximum daily development capacity is set based on the equipment and labour available. Proven and probable ore is mined preferentially over possible ore in the early years of the plan. Also, the fixed cost of operating the mine is taken into consideration whenever mining activities take place.Once the linear program is solved, it can be critically reviewed, and unrealistic results can be identified. Some resource allocations constraints can then be changed in certain sectors, and new results can be analyzed. “Whatif” scenarios can also be examined, such as determining the impact of hiring a contractor to develop a given sector, or dropping an ore zone completely from the plan."

Jan 1, 2005

By G. McIsaac

This paper discusses the formulation of a linear program with the objective of maximizing the cash flow of the long-term plan of an underground operation. A mine is split into eleven independent ore zones, each characterized by its reserves, required development, and mining method. Based on practical considerations, maximum rates are set for each zone?s development and production capacity. For the total mine plan, a minimum daily production rate is set along with a minimum feed grade to the mill. A maximum daily development capacity is set based on the equipment and labour available. Proven and probable ore is mined preferentially over possible ore in the early years of the plan. Also, the fixed cost of operating the mine is taken into consideration whenever mining activities take place. Once the linear program is solved, it can be critically reviewed, and unrealistic results can be identified. Some resource allocations constraints can then be changed in certain sectors, and new results can be analyzed. ?Whatif? scenarios can also be examined, such as determining the impact of hiring a contractor to develop a given sector, or dropping an ore zone completely from the plan.

Sep 1, 2005

By R. W. Boyle

"EDITOR'S NOTEPart 1 of this paper, published in the August issue, covered lithochemical surveys based on major, minor and trace elements in whole-rock samples from primary enveloping halos.Part 2, which follows, continues with discussions of surveys based on leakage halos, zonation of elements, stable and radioactive isotopic distributions, and geothermometric, geobarometric, thermoluminiscent, pedochemical, hydro-chemical, atmochemical and biogeochemical methods. It concludes with a selected bibliography.Surveys Utilizing Leakage HalosLeakage halos can be used as scalar or vector quantities in thesearch for deeply buried blind mineral deposits. In the first case, the occurrence of a leakage halo (e.g. a small pitchblende seam) may simply indicate the possible presence of pitchblende mineralization or orebodies; in the second case, the areal or three-dimensional distribution of leakage halos may, by their increasing frequency and I or increasing metallic or gangue element content, provide a means of vectoring in on loci of mineralization and orebodies. Examples of both cases are given in the following text.Leakage halos are of many types, as shown in Figure 2 (Part 1), and are best discussed with respect to their associated mineral deposits. Furthermore, it should be noted that leakage halos are frequently offshoots or extensions of enveloping halos. Where this occurs, careful tracing of the leakage halo(s) downward or upward respectively will often lead to the apex or nadir (bottom) of the enveloping halo(s) and ultimately to mineralization or ore."

Jan 1, 1982

By Owen Matthews

Introduction For the past year and a half, the mill of Cochenour Willans Gold Mines, Limited, McKenzie Island, Ontario has been roasting arsenopyrite-gold concentrates, prior to cyanidation, by means of a roaster employing techniques that are new and novel. The roaster is known as the Dorrco 'fluo-solids reactor', and the technique as 'fluidization'. The reactor has demonstrated its ability to roast a flotation concentrate containing arsenopyrite, pyrite, stibnite, small quantities of other sulphides, and some lime silicates and carbonates, yielding a calcine consisting mainly of porous iron oxide, plus the gold values. This calcine is readily amenable to cyanidation. Bulk shipments of concentrates to a distant custom smelter, as practised prior to this installation, has thus been eliminated, with appreciable savings in smelting charges, freight costs, and interest losses during shipment and smelting. This is the pioneer installation of fluo-solids roasting at a Canadian mill and up to the present performance results have not been published. It is the purpose of this paper to present the information now available for the benefit of other millmen who may be confronted with identical or similar problems to those encountered and solved at Cochenour Willans.

Jan 1, 1949

By A. S. Bayne

THIS paper will present a review of the mining operations of one of Canada's most lately established gold mining districts (1). The history of the Little Long Lac and Sturgeon River areas is interesting in view of the fact that, although they have long been the scene of a certain amount of mining activity, they remained little more than an uninhabited wilderness until 1933, since which time ten producing gold mines and mills have been established in permanent operation, eight of these having entered production since the beginning of 1937. As complete a background as possible will be given concerning the major influences having a bearing upon living and economic conditions in the mining communities. The object, here, is to show the diversity of problems which demand the attention of the operator starting up and operating a new mine in present times, and to indicate the ways in which these problems are successfully met in this district. A description of the power facilities and plant equipment will be followed by a summary of the problems encountered and methods applied in exploration and development. This is to aid in forming a background showing the circumstances which influence the mining methods and costs of the various operations. The paper will conclude with a description of the mining methods used and the costs of the operations, including summarized analyses of the stoping methods and mining conditions. The various phases of operation will be dealt with separately, in so far as this is possible, in order to present clearly the salient features. It is necessary, however, that the reader bear completely and constantly in mind the fact that in actual operations these phases arc, to a large extent, intimately related and greatly affect each other, as well as being, in turn, affected by other circumstances beyond the control of the operator. A few of these circumstances are: capital available during the development period and early stages of productive operation; strength of rock comprising the ore and its boundary walls; grade, size, shape, and location of ore-bodies; and many other natural items which must be carefully weighed in relation to the details of operation.

Jan 1, 1940

By V. A. Ettel

Current practices in electrolytic winning and refining of copper , nickel and zinc are reviewed from the point of view of their respective energy requirements. The electrical energy requirements of these processes are broken down in to the individual components, which belong to two basic categories: (a) thermodynamic energy requirements (G of the desired reaction) : (b) energy losses (anode and cathode polarizations, ohmic drops in the electrolyte and in the cell hardware, energy losses due to unwanted side reactions and electrical shorts). The individual energy components are separately examined for each electrolytic process and the potential for energy saving in these processes is discussed. It is shown that many potential energy-saving measures are uneconomical at the present time, as they increase over-all operating costs. The discussion is focused on those approaches which hold most promise for the future.

Jan 1, 1977

By Dong-min Lee

As the construction industry is becoming more large-scaled and complex, the BIM technology has been utilized throughout the industry. Since 2008, the construction industry in South Korea (Korea) has required carrying on BIM-based project continually. According to this trend, BIM S/W market, as well as BIM library market is also gradually activated. Many countries have already been establishing Web-based BIM library market, also Korea has been trying to establishing this Web-based BIM library market. In this study, through market research of Web-based BIM library market of advanced countries including the U.S.A. and U.K., establishment strategy of BIM library market to be derived by late starters that introduce BIM such as Korea, Japan and China was deduced based on current establishment status of BIM library market in Korea. In addition, deal with an issue that a clear revenue-sharing system between business principals of Web-based BIM library market is not available at the current stage was presented as a factor of inhibiting activation of BIM library market. So in order to offer a reasonable revenue-sharing strategy in BIM library market as conceptual level, a methodology and process of applying Game theory being used for deriving. It is expected that a reasonable revenue-sharing model between business principals would be presented as its standard of BIM library market to be more activated in the future.

Aug 1, 2013

The Cadia mine is shifting from the open pit operation to the Cadia East underground block cave. The resulting increase in milled tonnes and the decrease in fines production through shifting to block caving require an increase of over 25% in installed power. This expansion is being accomplished via the installation of up-front crushing and HPGR milling of the ore, with the SAG mill receiving a secondary crushed feed. This design, criteria and rationale for selection is presented. Over the coming years, the mine will further expand capacity. The target is to accomplish this with minimal addition of installed power or use of fresh water. This presents a challenge that epitomizes the future constraints on our resource dependent and intensive industry. The approach and proposed options to this longer-term expansion are also presented.

Jan 1, 2012

By C. Butcher

Numerical simulations of straight tube hydroforming of a dual phase steel were performed using both upper and lower bound constitutive models for porous ductile materials. The Gurson model is based upon an upper bound approximation to the material behavior and thus overestimates formability. Conversely, a lower bound solution to Gurson's unit cell geometry was developed by Sun and Wang to provide a conservative estimate of formability. The effect of a compressive axial load (end-feed) on damage development and tube formability is investigated. The resulting upper and lower bound models successfully captured the experimentally determined burst pressure, formability and failure location.

Jan 1, 2010

By Q. Han

A modified cast-on method has been developed to reinforce aluminum castings with steel insert. Defect-free bond between the steel insert and the aluminum casting has been consistently obtained. Data obtained from a push-out experiment indicated that the bond strength was much higher than that obtained using the Al-Fin approach. This paper introduces this modified method in four sections: the coating of the steel pins, the cast-in method, microstructure characterization, and the bond strength. The section on the coating of the steel pins contains coating material selection, electro-plating technique for plating Cu and Ni on steel, and diffusion bonding of the coatings to the steel. The section on cast-in method deals with factors that affecting the quality of the metallurgical bond between the coated steel and the aluminum castings. The results of microstructure characteristics of the bonding are presented in the microstructure characterization section. A push-out experiment and the results obtained using this method is described in the section of bond strength/mechanical property.

Jan 1, 2015

By Mengmeng Gai

This paper introduces a model-based automatic object recognition and registration framework to assist heavy equipment operators in rapidly perceiving 3D working environment at dynamic construction sites. A video camera and a laser scanner were utilized in this study to rapidly recognize and register dynamic target objects in a 3D space by dynamically separating target object?s point cloud data from a background scene for a quick computing process. A smart scan data updating method has been developed which only updates the dynamic target object?s point cloud data while keeping the previously scanned static work environments. Extracted target areas containing 3D point clouds were orthographically projected into a series of 2D planes with a rotation center located in the target?s vertical-middle line. Prepared 2D templates were compared to these 2D planes by extracting SURF features. Point cloud bundles of the target were recognized, and followed by the prepared CAD model?s registration to the templates. The field experimental results show that the proposed rapid workspace modeling method can significantly improve heavy construction equipment operations and automated equipment control by rapidly modeling dynamic target objects in a 3D view.

Aug 1, 2013

By Tassos Grammatikopoulos, Vladimiros Papangelakis, Douglass Duffy, Cheryl Washer, Srinath Garg

Flotation operations in Sudbury, Ontario, seeking to separate pentlandite and chalcopyrite from mixed sulphide deposits, produce pyrrhotite tailings that have been disposed of in tailings ponds for over 50 years. These reactive tailings are viewed as waste, despite containing ~0.8 wt% Ni, and represent an environmental liability because of their acid mine drainage (AMD) potential. Given the large quantities of pyrrhotite currently stored in Sudbury, and declining ore grades elsewhere, these tailings have shifted from being viewed as a waste to a potential resource. Recent advances in the bioleaching of low-grade sulphide ores have raised the prospect of bioleaching as a potential low-cost processing option. However optimization of this proposed process requires a thorough understanding of the mineralogy of the pyrrhotite tailings that would be leached. The work presented here addresses the characterization of two distinct Sudbury pyrrhotite tailings, namely from the Vale and Glencore operations, using electron microprobe, XRD and QEMSCAN analysis. Particular focus is given to how the mineralogy may affect bioleaching as a processing option, through the deportment of nickel and the various phases present

Jan 1, 2015

By Harvey McLeod

M3 -Technology HOWEVER:In practice we have limitations ?Clients: aggressive or cost based; inexperienced ?Consultants: ?expanding market w/training limitations ?Prescriptive designs ?Lack of senior oversight ?Regulators: difficult to retain technical capacity ?Stakeholders: perceptions and expectations ?Physical settings: challenging terrain, climate, soils/rock Do M3?s Perform? YES?Generally M3?s since mid-1960 do perform ?BC Closed Mines: Afton, Highmont, Trojan, Bethlehem, Cheni, SNIP, NO?ARD/ML issues?e.g. Equity Silver, Samatosum; selenium, cadmium, sulphate

May 1, 2010

By A. McLean, W. Q. Chen, W. Yan, M. Barati, Y. D. Yang

In order to maximally remove the harmful impurities phosphorus and reduce the loss of valuable elements from Si-based alloy for production of solar-grade silicon, thermodynamic properties of the Si-based alloy were studied. In this work a new model, the Molecular Interaction Volume Model (MIVM) derived from statistical thermodynamics, was successfully used in the Si-based and Si-Fe-based alloy. The calculation started from binary Si-Fe, Si-P and Fe-P systems, then the thermodynamic parameters of ternary systems could be derived based sub-binary systems. Using the activity coefficients of the elements in the Si-based alloys and the saturated vapor pressure of the pure substance of the components, mass fraction of P during vapor-liquid equilibrium can be calculated. The calculated thermodynamic parameters were compared with experimental data available in different publications, and it is found that the thermodynamic parameters calculated using MIVM model are in good agreement with the measured results. The calculated result shows that the mass fraction of phosphorus during vapor-liquid equilibrium of Si-Fe-P melt increases with the increasing phosphorus content and decreasing temperature. This is an important direction for experimental practice in vacuum or low-pressure EML refining of ferrosilicon for potential production of solar-grade silicon without significant vaporization loss of valuable element.

Jan 1, 2015

By H. Golzarpoor

Life Cycle Analysis (LCA) is a methodology for evaluating the environmental impacts associated with a product during its life cycle. LCA is identified as the most reliable method for verifying environmental impacts; however, current LCA-based approaches have certain limitations for environmental analysis of construction products. Integration of the LCA methodology with Discrete Event Simulation (DES) provides a sound framework for modeling and analysing the environmental impacts of construction products. LCA and DES is one possible combination for analysing the cause and effect of various scenarios where time, resources, and randomness of input variables affect the outcome and, therefore, has the potential to address the shortcomings of LCA in construction. Recent studies in disciplines other than construction such as manufacturing systems have revealed positive effects on evaluation of environmental metrics while integrating LCA with DES; however, this integration has not yet been applied for environmental analysis of construction products. By implementing LCA data in a DES model, this research proposes an environmental model of earthmoving operations in a case study. Environmental variables are simultaneously assessed with production variables in the same simulation model and the integration of DES and LCA is discussed.

Aug 1, 2013

By Louise Corriveau, Bronwyn Azar, Valerie A. Jackson, Luke Ootes, Jeff Harris

We use the results of new bedrock mapping, combined with geochemical point data and airborne radiometric data (in particular equivalent uranium concentrations) to help determine which geological units in the Paleoproterozoic Great Bear magmatic zone (GBmz) contain elevated uranium. The data collectively indicate that the highest primary uranium concentrations are in equigranular granites and subvolcanic/volcanic porphyries. Notably, these rocks host the majority of known uranium-bearing deposits and/or prospects in the GBmz. We speculate that the uranium in these deposits/prospects was derived from nearby, uranium-enriched rocks and was mobilized by much younger, circulating hydrothermal fluids. Sedimentary rocks of the Thelon and Dismal Lakes groups unconformably overlie the GBmz and are known to host unconformity-type and sandstone-hosted uranium prospects. Most likely, the uraniumenriched rocks of the GBmz acted as a uranium donor to these overlying sedimentary basins. The method of investigation employed in this study may be applicable to other ‘granitic’ terrains in order to identify regions with favourable rocks for uranium exploration.

Jan 1, 2013

By M. Kreuh

Crystalline Mg(OH)Cl and amorphous Mg2(OH)3C1 were successfully isolated from a hydrolyzed molten salt electrolyte sample in this work, It was found that the chemical form and crystallinity of the hydroxylchloride were controlled by the cooling rate of the molten sample when it was taken. Crystalline Mg(OH)Cl could only be obtained by cooling the molten electrolyte sample at a rate not faster than 0.6 °C/min, Upon more rapid cooling, the hydroxylchloride species precipitated as Mg2(OH)3Cl, The behavior of these solid hydroxylchlorides when contacted with fresh and non-hydrolyzed molten electrolyte at 550°C was also examined, It was found that the Mg(OH)Cl rapidly dissolved in the hot electrolyte and did not decompose into MgO at that temperature as would be expected from the literature, The dissolution rate of solid Mg2(OH)3Cl was found to be so slow by comparison that it resulted in the complete decomposition into MgO which thereafter was incorporated into the electrolyte as a suspended solid phase rather than dissolution.

Jan 1, 2004

By Giles St. Pierre

"The purpose of this paper is to report in a general way on the use of the Portaspec X Ray Spectrograph.At Manitou Barvue, we are milling two types of ores, copper and zinc. The control assay practice was to take grab samples at 4 hour intervals. These samples were dried in the mill, then taken over to the Assay Office where two operators would process them. Three hours later results were available at almost the same time as the operator was ready to take his set of grabs again, leaving no time for adjustments, if any were needed.After a reduction of personnel, there were no assays available on night shift. This practice was slow and inadequate, and a new way of doing control assays was investigated.After investigation the Portaspec was found suitable for the type of operation that we had in mind. The Portaspec is a conventional dispersive type of X Ray spectrograph. The instrument consists of three parts:The Power Supply The Spectrographic Head The Digital ScalerIn our case, where dried powder samples are analyzed, the instrument was provided with a two sample holder using one for the standard and the other for the sample. The operation of the instrment does not require any degree of skill or knowledge of chemistry or spectrography.Previous to buying the instrument, six sets of six to ten samples were sent to the supplier along with the assay for each sample. These samples were Cu. HDS., Cu. Conc., Cu. tls, - Zn. HDS., Zn. Conc., Zn. tls. A definite pattern was observed. For example - six Cu. HDS. samples ranging from .40 to .90 gave 10400 counts for the lowest to 16.040 counts for the highest. The number of counts were then plotted to give percentages."

Jan 1, 1971