Search Documents

By Brian E. Robertson

"This paper summarizes work carried out at the Dome Mine to mechanize the mining of narrow veins of less than 1.5 m in width by the introduction of new mining methods and specifically designed electric LHDs.Extensive mining trials have been conducted using sublevel blasthole, modified Avoca, and resuing mining methods. The introduction of the Microscoop and the Jarvis Clark remote, radio-controlled scooptram has increased mucking productivity.As a result of this work, additional narrow vein stopes are now being prepared for production. In the future, narrow vein stoping wil lprovide a greater percentage of the total mill tonnage.IntroductionThe Dome Mine, which is owned and operated by Dome Mines Limited, is located at Timmins, Ontario. Production has been continuous since 1910 and in 1984 was increased from 1814 to 2721 tonnes per day.At least six distinct ore types have been recognized at the mine. In general, these orebodies can be broadly categorized into wide and narrow deposits. The wide deposits are approximately lenticular in shape and vary in width from 10 m to 40 m. The narrow orebodies consist of quartz and quartzankerite veins ranging in width from a few centimetres to six metres. The average dip of the veins is 65 degrees.Since the I970s, mining activity has been largely concentrated in the wider orebodies using highly productive open sublevel blasthole and mechanized cut-and-fill stoping methods. With the demise of shrinkage stoping in 1975, investigations were initiated to develop new mining methods and introduce LHDs - truly designed for narrow orebodies. These investigations resulted in test trials of the sublevel blasthole, modified Avoca, and resuing mining methods. Consultations with equipment manufacturers and suppliers led to the development of the Jarvis Clark remote, radio-controlled electric scooptram and the introduction of the France Loader Microscoop."

Jan 1, 1986

By P. R. A. Andrews

"Graphite is one of the most versatile of non-metallic minerals because of its diversified properties, for example: it is unctuous; it marks readily; burns slowly; is almost chemically inert; is flexible over a large temperature range; is a good conductor of heat and electricity; is hydrophobic; has a negative temperature coefficient of resistivity; has excellent weathering properties; tends to emulsify with water-in-oil; is readily soluble in iron; and after oxidative treatment, can exfoliate like vermiculite. These properties give rise to its major uses in lubrication, refractories, marking instruments, electrical products and paints.Flake graphite is the variety which commonly occurs in Canada; the provinces of Ontario and Quebec contain the deposits of economic significance, although graphite occurs in other provinces. The beneficiation of graphite has been the subject of many investigations at CANMET, thus reflecting graphite 's importance as an industrial mineral. Thirty-eight studies relating to various aspects of beneficiation were conducted between 1918and 1989anda review of some of the more important studies is presented. The information includes mineralogy, beneficiation methods and results; flotation parameters and reagent concentration data are presented in tabular form. By so arranging the principal data, the research worker and production metallurgist will be assisted in the evaluation of graphite ores from a variety of origins."

Jan 1, 1992

By James L. Parks, David M. Kjos

"Designs, installation procedures and performance characteristics of martensitic cast steel concaves are reviewed. Longer wear life, fewer pieces to install and eliminating the need to scarf joints are the principal benefits of using martensitic steel to replace austenitic12% Mn (Hadfield's) steel, the traditional concave material for large gyratory crushers. Installation procedures that reduce the risk of breakage are described. Operating practices that affect concave performance are also discussed.IntroductionThe crushing machine considered to be the forerunner of the modem gyratory crusher was patented in 1878 by Charles M. Brown of the Gates Iron Works(1). The earliest gyratory crushers with receiving openings of 6 to 12 inches were fed by hand, and the crushing capacity of a mine was increased simply by installing more small crushers. The introduction of the steam shovel to open pit mining around the tum of the century provided an incentive for much larger primary crushers, and gyratory crushers with a 48 in. receiving opening were being built by 1910, followed not long afterward by machines with 54 in. and 60 in. openings to . Fortunately for the crusher maintenance people of that era, an austenitic 12% Mn steel with exceptional toughness was already available, having been discovered by Robert Abbot Hadfieldoi in 1882. Although small gyratory crushers working soft- to medium-hard rock reportedly used chilled cast iron (white iron) wear parts, these newer and much larger machines were fitted with ""Hadfield's manganese steel"" concaves and mantles to withstand the impact associated with handling large rocks .M E International first challenged the long-standing convention of using 12% Mn steel concaves in large gyratory crushers in the late 1960s when they supplied upper row concaves in martensitic cast steel for a 60-109 primary crusher at a taconite plant on the Iron Range. Since then, martensitic steels have been successfully substituted for 12010 Mn steel in concaves for more than seventy primary gyratory crushers processing iron, copper and precious metals ores, industrial minerals and crushed stone.This paper reviews materials, designs and performance characteristics of martensitic steel concaves in large gyratory crushers. The principal benefits include significantly longer wear life, fewer pieces to install and the elimination of scarfing. Obtaining the full measure of these benefits and minimizing the risk of breakage is strongly dependent on installation procedures, which are described in some detail. Operating practices that can affect performance are also discussed."

Jan 1, 1993

By A. M. Girodo

"Dorbyl Heavy Engineering has been manufacturing winders since 1949 mostly for the South African mining industry.Table 1 shows that the vast majority of winders have been double drum winders. At the greater depths with larger ropes being employed, it became apparent that multi-rope winders would be needed. The high stress variation in Koepe winder ropes at great depths especially beyond 2000 m, ruled out this possibility. Thus the original concept was borne for the Blair multi-rope winder where the stress level variations in the rope would be as per the well known, tried and tested double drum winder. The Blair multi-rope was also devised to increase payload by using multiple ropes.With the increasing costs of transporting men and material coupled with fact that orebodies are getting deeper, various feasibility studies have been carried out by South African mining houses. For this reason Dorbyl Heavy Engineering has done conceptual design work of both double drum and Blair multi-rope winders with diameters up to 8.5 m dia (still well within our manufacturing capabilities). These feasibility studies have looked at depths approaching 4000 m*.This paper covers the typical duties leading to the choice of single drum, double drum, Koepe and Blair multi-rope hoists on South African gold mines. A brief synopsis of Dorbyl hoists in use in the South African mining industry, with some indications of future trends, will be discussed.With current installed depths of wind approaching 2500 m, the Blair multi-rope hoist has been used extensively for the heavier payloads.Some of the main considerations pertinent to the design of the Blair multi-rope hoist are illustrated together with the implications of using this type of hoist to winding depths of3000 m to 4000 m in the foreseeable future."

Jan 1, 1995

By P. Fossi

This report describes a pilot-scale study of a hydrometallurgical process to treat high-grade nickel matte or a nickel-cobalt sulphide precipitate to produce high-purity electrolytic nickel. The first step of the process is the oxidative leaching of the nickel-bearing material by nitric acid; the nitrous gases generated during leaching are reconverted to nitric acid. The crude nickel sulphate nitrate solution is purified and is then subjected to a denitrification step. Nitrate separation is effected either by the crystallization of nickel sulphate or by precipitation of basic nickel carbonate. The electrolyte is prepared from the nitrate-free material and nickel is then recovered by electrolysis of the sulphate solution using insoluble anodes. Some technical and economic problems encountered with this processing route are discussed and the method is compared to the "all-chloride" process developed by Société Le Nickel.

Jan 1, 1977

By Stanley G. Butcher

"The methods generally applied to predict performance and financially evaluate beneficiation options are reviewed.Typical costs f or a western Canadian thermal coal operation are examined. Preparation-from truck dump to loadout-frequently amounts 10 over a quarter of total minesite costs. Failure to achieve projected yield-whether caused by mine or plant problems-s-substantially increases production costs because more coal has 10 he mined to meet a specific market demand. Problem identification by mass/ash balances is recommended.Thorough characterization of the coal and associated waste materials and more reliable prediction of beneficiation process performance are therefore essential to determine a project 's financial viability.IntroductionWestern Canadian coal prep a ration plant capacity is partway through a massive expansion program . In 198 1 potential product ion was 14 million tonnes, by 1985 it will be 26 million tonnes per year. Only two years ago the industry was concerned whether it could sustain this rate of growth to meet market demands : now with diminished market demand and lower coal prices being offered by our international competitors there are doubts whether t his potential will be fully employed , even by 1990.One direct consequence o f the occurrence of a variety of coals in a stunningly beautiful but complex geo logical setting such as the Rocky Mountains and their Foothills is that each project is unique. Coal is a low value per tonne product. To supply distant markets from geographically isolated deposit s necessitates expensive , dedicated , infrastructure . T o be profitable these operations must achieve eve ry advantage of the economy of scale.Each of the mi ne complexes commissioned in the 1970s experienced severe problems in the area o f co a l preparation . Most bought their way out , paying for major plant modifications by increasing the scale of their total operation . The current market recession may not allow new operations this route to profitability.The objective of this paper is to illustrate the economic impact of coal preparation problems on the profitability o f the total minesite operation and thus provide a sound basis for decision making process."

Jan 1, 1985

By Zara Hosseini

?Microseismicity ?Seismic Systems ?Intrinsically Safe and Explosion Proof Seismic System ?Case studies: ?Gas Drainage Optimization ?Fault Identification ?Conclusion Seismic Event ?Occurrences in which energy is released in the rockmass creating a series of seismic waves propagating throughout the rockmass ?Can cause a Fall of Ground or CoalBurst Factors creating Seismicity: ?Mining at Depth ?High stress zones ?Major geological structures ?Mining practices and strategies ?Mining activities i.e. drilling and blasting

Aug 1, 2013

By M. Remillard, M. Garon, D. Hodouin, M. Therien

"Nineteen streams in the copper and zinc flotation units of the concentrator of the Matagami Division of Noranda Inc. have been sampled f or particle size distributions, chemical assays, and gold and silver contents in each particle size interval. The data are upgraded by the mass balance package BILMA T. These results, in conjunction with microprobe analyses, are used to quantify the silver losses in the copper cleaning flotation stages and to determine how over-all silver and three silver-bearing minerals are recovered in the plant final products. RESUMEDix-neuf produits des circuits de flottation du cuivre et du zinc de la division Matagami de Noranda Inc. ont été échantillonnés pour leur distribution granulométrique, leurs analyses chimiques et Ie contenu d'argent et d'or des fractions granulométriques. Le bilan métallurgique a été obtenu à l'aide du programme BILMA T. Ces résultats, couples avec une étude minéralogique a fa microsonde, sont utilisés pour quantifier les pertes argentières aux diverses étapes de nettoyage du circuit de cuivre et pour déterminer la répartition de l'argent et des trois minéraux argentifères dans les produits finals de l'usine."

Jan 1, 1988

By Sukumar Bandopadhyay, Arunapuram Sundararajan

"Unique production and environmental problems are associated with multiple seam mining where dragfines are used for overburden and interburden removal. On the production side, the problems are decreased dragfine efficiency in chopdown operations, the general need for spoil rehandle, complications in sequencing stripping and coal handling operations, and potential stability problems in highly stacked spoil. Many variations of dragline methods have been reported in the literature to encounter these problems. Because of the physical properties and peculiar hydrology of sub-arctic region mining of multiple seams in such areas probably could not be done with the methods used in temperate regions.The properties of thawed material would make spoil hard to place in a stable manner and thus would influence the mini sequence. For instance, multiple seam mining which requires some rehandling of spoil and prolonged exposure of overburden and interburden material might be precluded by the instability of thawed spoil and therefore mining techniques have to be modified. Since the deployment and operation of a dragline in modes different from conventional schemes will affect productivity, it will be necessary to study the effects on production of changing the dragfine operational schemes. This paper presents a heuristic simulation model of multi-seam dragline operation of a sub-arctic mine that can be used to analyze the handling of overburden and detailed study of the dragfine performance."

Jan 1, 1986

By K. Parameswaran

This paper builds on presentations made at the Conference of Metallurgists (COM) 2015, COM 2017 and Extraction 2018 and associated papers published in the respective conference proceedings. Based on the classic Brundtland Commission definition of sustainable development as “development that meets the needs of the present without compromising the ability of future generations to meet their own needs,” the paper describes how metal mining can be compatible with sustainable development and how sustainability considerations have been applied in the primary copper industry, using several examples of sustainable mining practices from ASARCO LLC operations. Finally, the paper discusses how these considerations might be used in the future by discussing the need for developing a sustainable development strategy and how this strategy can be aligned with the United Nations Sustainable Development Goals. INTRODUCTION The primary copper industry comprises: mining (also referred to as “extraction”); mineral processing (also referred to as “beneficiation, “milling” or “concentration,”) which includes leaching, solvent extraction (SX), crushing, grinding, froth and flotation operations; and metallurgical processing which includes smelting and converting; refining, which includes fire-refining or anode refining and electro-refining; and electrowinning (EW). There are two routes for producing refined copper: hydrometallurgical and pyrometallurgical. The hydrometallurgical route comprises mining (open-pit and underground), mineral processing (crushing and grinding — for heap leaching only; leaching and SX) and metallurgical processing (EW). The pyrometallurgical route involves mining, mineral processing (crushing, grinding and froth flotation) and metallurgical processing (smelting, fire refining and electro- refining). The primary copper industry is capital, water, resource and energy intensive with the potential for significant environmental impacts, if the environmental aspects are not properly managed. ASARCO LLC (Asarco) was organized in 1899 as the American Smelting And Refining Company. Originally a consolidation of several lead-silver smelting companies, it evolved over the years into an integrated producer of primary non-ferrous metals, including copper, lead and zinc and associated co-products. Grupo México, S.A.B. de C.V (Grupo México) acquired Asarco in 1999. Today, Asarco is a vertically integrated producer of primary refined copper and associated co-products such as gold, silver, selenium and tellurium. Asarco operates three open-pit mines and mills, two leach, SX-EW plants, a copper smelter in Arizona and a copper electrolytic refinery in Texas.

Jan 1, 2019

By A. L. Craven, J. P. L. Bacharach, D. B. Stewart

"Inert gas use for underground mine fir e control is a well-established mature technology in some parts of the world. This paper reviews three candidate inert gases and describes three case histories where inert gas fire-fighting technology was used in actual underground fires.IntroductionInerting is the introduction of an inert gas into an atmosphere in contact with a fire to reduce the level of oxygen and hence the intensity of the fire 10 the point of extinction. The benefits of inerting include:a. Reduced Explosion HazardBy displacing oxygen from the atmosphere surrounding the fire the risk of secondary gas explosions is reduced. For example, simple methane-air mixtures at standard temperature and pressure are non-explosive below 12% oxygen. In actual mine fires, combustible gases may include hydrogen and carbon monoxide as well as methane. Such gases are also rendered non-explosive with oxygen removal to below 40/0. Fuel-rich oxygen-deficient mixtures can however be made explosive through dilution with air. Such dilution can occur downwind of the fire. It is also important to remember that the atmosphere in a sealed-off fire zone is rarely homogenous.b. Reduced Fire Intensity and SpreadIn a fire zone the initial combustion may well set alight materials surrounding the fire. Inerting can reduce the intensity and spread of secondary combustion and can cool the area surrounding the fire zone after the fire itself has been extinguished.c. Reduced Air LeakageLeakage of air into sealed areas in excess of the natural leakage may be reduced either by introducing inert gas into the leakage paths to replace air or by pressure balancing seals and providing a chamber of nitrogen on the outbye side of the seals. Both methods assist in the reduction of the intensity of combustion and hasten oxygen starvation."

Jan 1, 1986

By William M. Luff

This paper outlines the regional geology and history of the area, and summarizes the stratigraphy, structure and geology of the Brunswick No. 12 mine area. The Brunswick No. 12 deposit is a stratiform massive sulphide body. It occurs in rocks of the Tetagouche Group, which is believed to range in age from Lower to Middle Ordovician. The stratigraphic sequence, including the stratiform orebody, in ascending order consists of older metasedimentary rocks, augen schist, metasediments, augen. schist, footwall metasediments, the -massive sulphide body, iron formation, hanging-wall metasediments, siliceous tuff, basic volcanic rocks , basic iron formation and a porphyry dyke. This sequence is similar to that at some other deposits in the area. Four phases of structural deformation are known to be present in the Brunswick No. 12 mine area. The first deformation folds (F1 ) and associated faulting are the most important factors in determining the distribution of the massive sulphides. This deformation has resulted in the massive sulphides being separated into four zones: the Main Zone, the West Zone, the East Zone and the V-2 Zone. Brunswick Mining and Smelting Corporation Limited is actively mining, developing and exploring the deposit.

Jan 1, 1977

By P. W. A Severin

"The Sturgeon Lake deposit, a partly eroded lens of massive sulphides with an underlying sulphide stringer zone, is one of five orebodies that occur in the Sturgeon Lake area of northwestern Ontario within volcaniclastic rocks of the Archean Wabigoon Subprovince in the Superior Province of the Canadian Shield.The Sturgeon Lake Cu-Zn-Pb-A g-Au deposit was discovered in October 1970 as a result of an I.P. survey. Production from this open-pit mine began in March 1974 and continued until the ore was exhausted in March 1980.The Sturgeon Lake property is underlain by basaltic volcanics, minor amounts of mafic lapilli tuff and rhyolite volcaniclastics. A quartz crystal-bearing rhyolite occurs at the top of the felsic volcaniclastics and is ""capped"" by the Sturgeon Lake massive sulphide deposit. The felsic volcanics have been intruded by a crudely layered sill-like, carbonatized mafic intrusion. Recent work suggests that the felsic rocks that underlie the Sturgeon Lake deposit are lateral equivalents of those in the vicinity of the Mattabi Mine and are not correlative with the dacitic volcaniclastics that underlie the Lyon Lake and Creek Zone deposits. Hydrothermal processes that resulted in the formation of the Sturgeon Lake orebody have resulted in a depletion of Na2O, CaO and FeO and an increase in MgO, K2O, copper and zinc. In the vicinity of the sulphide stringer zone, the rhyolites are ""bleached"" due to silicification and sericitization. The rocks lying immediately below the massive sulphides are locally strongly chloritic.The Sturgeon Lake deposit may have formed on a top ographic high which prevented mafic flows and dacitic volcaniclastics that underlie the Lyon Lake and Creek Zone deposits from inundating the Sturgeon Lake fumarolic vent from the west. Continued or resurgent activity from the Sturgeon Lake fumarole may have resulted in the formation of the Lyon Lake and Creek Zones as more ""distal "" deposits in topographic lows. The Sturgeon Lake, Lyon Lake and Creek Zone deposits were subsequently overlain by mafic tuffs and flows."

Jan 1, 1982

By James Logan

BC Alkaline CuBC Cu--Au PorphyriesAu Porphyries ?Formed over narrow time interval ~205 Ma ?from silica deficientvsalkali-enriched magmas ?At shallowdepths ?Structuralcontrol ?Cu-Au-Ag, trace Mo ?Oxidized system anhydrite, magnetite ?Multipleintrusions & multiplemineralized centres

May 1, 2006

By G. R. Larocque

"The Loss Prevention Program and management style applied at Kidd Creek enabled them to maintain a 1.02/200 000 man-hours accident frequency over a 20-year period. Falconbridge Limited, Kidd Creek Division operates a major zinc, copper, silver mine, two gold mines and a metallurgical facility in Timmins, Ontario. The metallurgical site and the base metal mine are 17 miles apart and joined by their own railroad. The minesite consists of two shafts, one 3000 feet deep and the other to 5200 feet deep, as well as the necessary maintenance and service shops. The metallurgical site consists of a 14 000 STPD concentrator, a zinc refining plant, copper smelter, copper refinery, and the necessary maintenance shops. The two gold mining operations are adjacent to the metallurgical site.At the time of writing this paper the workforce consisted of some 2500 people divided between the two sites. Nine hundred and ninety-two employees are stationed at the minesite, with the remainder at the metallurgical site and gold mines. The workforce in the Timmins operation is non-unionized and reflects the belief that employee interests are well served.Beside providing competitive wages and an excellent benefit package, Kidd Creek takes special pride in its employee relations practices and continued efforts in communication.In each of the programs referred to, there have been equal involvement by both management and the employees. Each crew, under the direction of a supervisor, makes up its own health and safety committee. To maintain a successful Loss Prevention Program, it is essential that management and the employees work closely together and provide meaningful input and effort to succeed.At this point, refer to the lost time injury frequency as a measure of failure and refer to the opposite end of the scale as the measure of success. The ultimate goal of every operating company is to have a zero frequency, therefore denoting 100070 success. The company uses most of the tangible safety aids found in other mining operations, such as safety posters, safety reminders, check lists, and the use of the Neil George Safety System. The difference is the manner and style of management at the Kidd Creek Division. Their ""open door"" policy and the close association, between management and the employees, has always served them well. Also, at Kidd Creek they believe they have a well-trained and dedicated workforce."

Jan 1, 1989

By N. Staroselsky

"Significant energy savings are often possible for centrifugal compressors operating in parallel by improved control strategy and improved instrumentation. Blow-off can usually be reduced by improved surge control combined with a better control strategy for loading and unloading the group of machines. More precise and stable pressure control then becomes possible. This improved control strategy will also decrease the frequency of operation near the dangerous limits of surge or overload or overspeed. A sample station of mixed centrifugal and reciprocating compressors is examined and a substantial energy saving with the recommended control strategy is projected from operating data. Present Operating Conditions of the Compressed Air StationThe Compressor StationThe compressor station described here has three centrifugal compressors and three reciprocating. It supplies a mine in New Brunswick.Compressed Air and Power ConsumptionFigure I and Figure 2 provide graphs of air consumption and pressure changes based on the owner's data.During the typical two-shift operating day (Fig . I) in the non-productive shift (midnight to 8:00 a.m.), the consumption stays at a level of 9,000 SCFM. This corresponds to a pressure of 110 PSIG. Then, after 8:00 a.m ., the air consumption starts to increase and th e pressure decreases. Around 10:00 a.m., the consumption reaches its maximum level at 97 PSIG. Around II :30 a.m., the air consumption starts to decrease because of the production drop during the lunch break of the first shift. Pressure increases again up to 109 PSIG. After the break, consumption rises to its maximum level over 16,000 SCFM andpressure drops to 97 PSIG.Around 2:30 p.m., the air consumption drops sharply to 9,000 SCFM because of the production decrease to zero level. This drop results from changing of shifts. The pressure at this time increases again up to 110 PSIG. The second shift (2:30 to II :30 p.m.) is an alogous to the first.During the three-shift operating day, the break around 4:00 . a.m . and the shift change around 6:30 a.m. cause sharp drops in air consumption. The pressure for almost the entire night shift stays near 110 PSIG because the station is working with blowing-off even under the maximum consumption. The analysis of Figures I and 2 shows that the pressure varies with the air consumption changes. During non -productive time (non-production shifts , shift changes and breaks) or during the night shift, the total station capacity is proportional to the discharge pressure. By decreasing the level of this pressure up to 97 PSIG, the flow of the station may be decreased during the non-production time as follow s:"

Jan 1, 1980

By W. F. Giuvlore, E. Mcroberts, T. S. Golosinski

"The rising demand for Canadian coal and depletion of shallow deposits, most suitable for surface mining, result in rapidly increasing volume of waste materials which have to be moved by the coal mining industry. While at present this challenge is being successfully met using conventional mining methods, in the future, innovative methods must be considered if Canadian coal is to remain competitive.The need for more efficient mining methods is also faced by the oil sands industry to assure competitiveness of the synthetic oil price.A look at the world mining practice indicates that large volumes of material can be economically mined and moved by the continuous mining systems comprising bucket-wheel excavators, belt conveyors and stackers. To assess the state of art and applicability of this mining method to Canadian conditions, the field trip was organized by the Department of Mining Engineering o f the University of Alberta, to several typical mining operations in Europe. It is in Europe where the continuous mining methods were developed and are almost exclusively used in large-scale surface mining."

Jan 1, 1984

By O. Mejia

"As study was undertaken to investigate the relationship between mill liner wear and grinding energy efficiency and to assess the opportunity to control mill speed to improve energy performance as mill liner wears. The study involved analysis of plant operating data and liner wear profiles over time. The operating work index was found to be an effective tool to identify the decrease of grinding efficiency along the liner service. The plant data show that the mill grinding efficiency as determined by monitoring the operating work index, and throughput decreases as liner wears. However, efficiency and throughput can be maintained by either changing the liner more frequently or by increasing the mill speed. Two scenarios for increasing mill throughput were analyzed. The first one involves changing the liner before the efficiency drops and the second one requires increasing the mill speed from 75% to 79%. Both scenarios show financial benefits that can be used in mill operations.INTRODUCTION The analysis of the mill power draw is used in this study as a key parameter for comparing mill liner profile and its effect on mill performance. Current technology and simulation software used in the mining industry do not factor in the impact of liner wear profiles in grinding efficiency and mill throughput (Toor, 2013). To address this gap, this study provides an analysis of key factors affecting mill throughput and grinding efficiency: mill speed, ball loading, and liner profiles. Several years of plant mill operating data, published research papers, and MillTraj® simulation results are used to demonstrate that face angles impact grinding efficiency and throughput and that mill speed can be used to overcome this problem. Moreover, the liner profile wear analyses clarify a mismatch between actual and estimated power draw calculations."

Jan 1, 2019

By C. R. van Staal, L. R. Fyffe, J. A. Winchester

"The geochemical characteristics of Early Paleozoic volcanic rocks are used to establish the following tectono-volcanic regimes in the northeastern mainland Appalachians: foreland continental rift volcanics; fore-arc ophiolites; island-arc volcanics; back-arc ophiolites; and back-arc ensialic volcanics. A Late Precambrian calc-alkaline magmatic arc bounds the Early Paleozoic volcanics to the southeast.The Precambrian calc-alkaline volcanics of the Caledonian Highlands, primitive Cambro-Ordovician oceanic-arc volcanics of the Eastern Townships, and within-plate Ordovician volcanics of the Miramichi Highlands can be related to a progressive change in mode of subduction from compressional Andean-type in the Late Proterozoic to extensional Western Pacific-type in the Early Paleozoic. The development of marginal oceanic basins in the Paleozoic created a more favourable environment for volcanogenic sulphide deposition, particularly in back-arc areas.The influence of tectonic setting is reflected in the distribution, size and metal ratios of the massive sulphide deposits associated with the volcanic rocks; deposits within intra-oceanic arcs in the Eastern Townships of Quebec average two million tonnes grading 2.2% Cu, 4.0% Zn, and 0.6% Pb, whereas those within a back-arc, ensialic rift near Bathurst, New Brunswick, average nine million tonnes grading 0.6% Cu, 5.4% Zn, and 2.2% Pb."

Jan 1, 1990

By Derek E. McBride

"Exploration work in the Beardmore - Tashota area has led to a reinterpretation of relationships between gold mineralization and the geologicalevolution ofthe area. The host volcanic rocks form two parallel volcanic belts connected by a much smaller cross-cutting band, which trends northeast from Beardmore to Tashota. This connecting band consists of mafic and felsic volcanic, plus clastic sedimentary rocks in a sequence conformable with the contact of the Onaman Lake Batholith to the east. A metamorphic aureole or incorporated xenoliths are lacking along this major contact and the only intrusive relationship observed is chilling between mafic dikes and a cold host granite in proximity to it. Granite dikes are totally lacking in the volcanic succession, or the overlying sedimentary sequence. A major part of this sequence consists of a polymict basal conglomerate with granite boulders and volcanic clasts in a fine-grained chloritic matrix. The nearest source for these boulders is the Onaman Lake batholith.Gold mineralization in significant economic quantities (+ 50 000 ounces) occurs at the top or above the mafic volcanic succession as quartz bands. In the Northern Empire Mine, the band is conformable, folded, boudinaged and the mineral zoning shows a relationship to variations in the host rock, not structural overprinting. In general, where the host mafic tuff is medium-grained, the quartz band is thicker, up to a metre wide, and carries economic grade; where the tuff is finer-grained and bedded, the band is very thin and low grade.Stratigraphic control and metal zoning shows that the mineralization formed as part of the development of the volcano- sedimentary succession. The other major deposits in the area (Leitch and Sturgeon River) have a similar structural history suggesting that they are also syngenetic in terms of the stratigraphic development. Regionally, these deposits were emplaced prior to any significant tectonic deformation but at the end of the mafic volcanic event.The mafic activity was related 10 a period ofextension which caused the volcanic troughs to develop along centres of rifting. The hiatus at the end of this event permitted extensive hydrothermal systems to form and deposit siliceous exhalite bands within sedimentary or terminal mafic volcanic environments in promixity to major thermal sources. Subsequently, the Kenoran Orogeny deformed the entire succession into upright folds with a sub-vertical schistosity. Evidence shows that the deposits have remained intact since deposition."

Jan 1, 1987