Search Documents

By T. E. Smith

"This paper describes the application of a motor-driven flywheel unit, known as a peak shaver, to compensate for the cyclic load fluctuations of a large electric dragline installed at Pine Point Mines, near Great Slave Lake in the Northwest Territories. Of particular interest in this application is the fact that the power system supplying the dragline is a relatively small isolated system, with the major generating source approximately 170 miles from the mine.The cyclic load fluctuations of the dragline are theoretically capable of producing a maximum swing of up to 11 megawatts, which approaches nearly 50% of the installed generating capacity. To reduce these load fluctuations to acceptable limits various alternatives were considered, leading to a decision to install a peak shaver to optimize the operations of both the mine and the power system. Without the peak shaver, the dragline operations would be severely curtailed and additional diesel generation would have to be run at considerable expense, otherwise the power system frequency fluctuations would be totally unacceptable. With the peak shaver, power and frequency fluctuations are kept within tolerable limits, and optimum economic operation of the diesel generation is obtained.The paper outlines the steps leading to the selection of the peak shaver as the compensating device, describes the equipment installed and gives details of operating experience with the dragline/peak shaver combination since installation early in 1979. This .peak shaver is the first of its kind in North America, the only other peak shaver installation being in Australia.IntroductionPine Point Mines Limited owns zinc-lead mining and milling operations located at Pine Point, Northwest Territories, 5 miles south of Great Slave Lake (Fig. I). The company is staffed and managed by Cominco Ltd., which has a 69% interest in Pine Point Mines.Mining activity in the Pine Point area was first recorded in 1898, when the Yukon gold rush was on, but when the zinc/lead showings in the Pine Point area did not yield much in the way of gold, interest in the area soon waned. Cominco Ltd. first acquired some claims in the Pine Point area in 1928, but interest was sporadic until the early 1950s, when extensive exploration indicated rich pockets of zinc/lead ore near the surface. Pine Point Mines Limited was formed in 1951, with Cominco acquiring a majority interest in the company."

Jan 1, 1980

By David L. Anderson

This paper explores the financial impact of the initial version of the Saskatchewan Potash Reserve Tax; first, a one; and second, in conjunction with the other taxes affecting the industry's profitability. A though the introduction of the Reserve Tax is shown to lead to a substantia increase in a hypothetical firm's effective tax burden, the more unusual outcomes frequently attributed to this levy on y occur after the imposition of other non-provincial tax rulings. Despite this qualification, the results obtained suggest that the Reserve Tax undoubted y acted as a catalyst in the polarization of attitudes during the ear y period of industry/government confrontation

Jan 1, 1979

By C. J. Newman, D. J. Kemp, R. M. Sweetin

"The smelter is described by area; feed preparation, continuous furnace line, gas handling and auxiliary systems, blister refining, Hazelett casting of thin anodes, and scrap remelting. Early smelter campaign data is presented and compared to design. Some modifications to the basic design of the furnaces and gas trains are indicated, with their respective impacts on improving smelter performance.Plant compactness, the use of jumbo tanks, and a highly automated electrode handling system are featured in the refinery description, with brief coverage of the liberator and slimes leaching sections. Early experience in refining thin regular Hazelett anodes, and submersible pump recovery of raw slimes are relayed, together with automatic stripping from titanium blanks.Refinery tonnages and operating parameters are given showing the relatively trouble-free attainment of refinery design performance.IntroductionPrevious papers and articles ( 1), (2) ,(3 ) have described the metallurgical facilities serving the copper-zinc-silver Kidd Creek orebody located near Timmins, Ontario. For convenience a brief review of their mid-1983 operating status is presented.The concentrator, originally designed for 9,000 short tons, was commissioned in late 1966. It can now comfortably process over 13,000 metric tonnes per day largely as a result of the addition of a fourth circuit in 1978."

Jan 1, 1984

By G. R. Cope, J. S. Getsinger, K. D. Lund, T. Neale

"Mineral exploration in the Sicker Group, a belt of Paleozoic volcano-sedimentary rocks on Vancouver Island, has traditionally centred on auriferous polymetallic volcanogenic massive sulphide deposits such as those currently mined by Westmin Resources Ltd. near Buttle Lake. Recently, however, the focus of exploration in the Sicker Group has shifted toward targets of structurally controlled gold concentrations, with notable success. Major north and northwesterly-trending structural features such as the Cowichan-Horne Lake break (one of several regional high-angle thrust fault s active throughout a long period of geological time) and related fault systems have contributed to localization of gold mineralization.Using the extensive information database compiled by MPH Consulting Limited during numerous exploration projects in the Sicker Group, two cross sections through areas with significant gold occurrences southeast of Port Alberni are presented. The cross sections combine geological, geochemical and geophysical data in an attempt to emphasize the relationship between structural trends and gold mineralization. Examples from specific properties, including gold discoveries along the Mineral Creek fault zone, are used to illustrate this relationship."

Jan 1, 1990

By J. Elderton

"The combination of A C induction motor and flu id coupling, of either the fixed or variable filling type, constitutes a simple, low cost, highly reliable drive unit, with many applications in the mining field.The paper will, however, concentrate on the variable filling fluid coupling in three principal applications-conveyor starting, infinitely variable speed control for slurry and slimes pumping and dewatering pumps for deep mines. Fluid couplings can be used with standard or custom-built control gear equipment, ranging from the most simple, time-based open loop types, to those having the latest microprocessor techniques.IntroductionThe first industrial applications of fluid couplings included their use in the mining field as hydraulic slip regulators for flywheel generating sets. These installations, usually rated at around 1700 to 2500 hp, were located at mine shafts where the electrical grid transmission lines were not strong enough to cater for the peak power demands of the cage winding cycle. In Canada, the first two significant examples of variable filling fluid couplings for mining were on conveyor drives, at Steep Rock Mines Limited, closely followed by the major iron ore handling term inal on the St. Lawrence River at Sept-Iles. Successful and reliable operat ion of the fluid couplings at these two sites set the pattern for use on many subsequent mining projects throughout the Canadian Continent."

Jan 1, 1986

By A. K. Ratte, C. M. Brown

"IntroductionIn autogenous mills, grinding of the ore feed is accomplished by the direct action of the variously sized rocks making up the feed on each other and the mill interior. Size reduction is achieved without the addition of grinding media foreign to the mill feed, differing in this respect from rod, ball, and pebble milling. The term ""semi-autogenous"" has entered common usage in the industry to describe autogenous mills to which supplementary grinding ball additions are made to increase the rate at which size reduction of the mill feed occurs, beyond that achieved solely by the action of rock on rock. In a semi-autogenous grinding (SAG) mill, 50Jo to 10% of the mill volume may be occupied by grinding balls, whereas a range of 25% to 45% is more usual in ball milling.The comminution of mineral ores using ""conventional"" techniques has been described in previous papers. In conventional operations, size reduction of mined ore, and liberation of the valuable mineral content, is typically accomplished using flowsheets employing two to four stages of crushing. Crushing is followed by one to three stages of grinding and classification using various combinations of rod, ball, and pebble mills. This paper describes operations employing autogenous or semiautogenous grinding as the principal stage in the comminution process. Primary crusher discharge, or in some instances run of mine ore, is fed directly to an autogenous or semi-autogenous grinding circuit. Final product sizing may be accomplished in a single grinding stage, the mills operating in closed circuit with classification equipment, or in several stages using autogenous and semi-autogenous mills for primary grinding, and ball or pebble mills for secondary grinding. In several operations a portion of the primary mill discharge is crushed in an intermediate comminution step, these circuits being called autogenousball- crusher circuits (ABC). Many different flowsheets exist, but common and important to most are crushed ore stockpiles, reclaim feeder and mill feed conveyor systems, pumps, screens, and classifiers. Autogenous grinding is employed in both wet and dry processes, although today wet predominate."

Jan 1, 1989

By Denghong Wang

Abstract- The Ashele Cu-Zn deposit is a recently discovered volcanogenic massive sulfide deposit in Xinjiang, China, hosted by Lower to Middle Devonian submarine bimodal volcanic rocks. The primary ores of this polygenetic deposit are represented by massive syn-depositional pyrite, chalcopyrite, and sphalerite, and were formed by submarine exhalation. Hydrothermal alteration consists of strong sericitization, chloritization, silicification, and carbonatization of the metavolcanic rocks beneath the massive orebodies. Depletion of Na2O is an obvious chemical change in the hydrothermal halo. Geological and geochemical evidence suggest that the Ashele Cu-Zn massive sulfide deposit was formed by submarine exhalation related to bimodal volcanic rocks, trapped in a rifting basin, then deformed by shearing, and thermally metamorphosed by the intrusion of dacitic porphyry. Sulfur and lead isotopic studies indicate that metals such as copper and zinc may have originated from spilites, but that volatile components, especially sulfur, were derived directly from submarine volcanic magmas.

Jan 1, 1999

By Craig Dirk

Agenda Applications of ?GPS ?Drill Navigation ?Cycle time monitoring ?UDS / Boom Stress monitoring ?Payload systems ?Laser Surveying Future Applications

May 1, 2006

By M. R. KEYS

"The property is about 120 miles north of Red Lake in the Favourable Lake area, district of Kenora ( Patricia part) , Ontario. The original discovery was staked by K. Murray in December, 1927. The first development work was done by the Favourable Lake Mining and Exploration Company. In 1936 Newmont Mining Corporation acquired control of the property and developed it to production by September, 1939. Production to the end of 1945 had a value of $7,534,656 from 441,457 tons of ore, an average value of $17.04 a ton . This production was mainly from gold and silver, with lead and zinc of subordinate importance.The rocks in the vicinity of the mine trend in a north-south direction. From east to west the sequence is: (1) A dark-coloured, massive rock, presumably a flow, composed mainly of quartz and biotite. ( 2) A buff- coloured, scricitized rock locally containing quartz phenocrysts and black hornblende. This is an alteration product of the dark variety and is later than the folding. It occurs mainly within the dark rock. (3) A series of sediments comprising thin beds of greywacke, grit, quartzite, conglomerate, and iron formation. ( 4) A gabbro sill, now largely altered to amphibolite.With the exception of the buff type, these rocks dip 80°E. The buff rock has a very irregular outline in comparison with the other rocks and appears to dip somewhat more flatly east. Felsite and diorite dykes are also present. These have a general strike of S.60°E. and dip 65°S .W. A post-ore diorite dyke trending N.15°E. occurs about 2,000 feet east of the mine area."

Jan 1, 1954

One Data Set for the Lifecycle Complete data captured at the logging stage benefits the entire life cycle Exploration Technical Studies Production and Milling Visible Light Spectrum Hyperspectral, put simply, is the interaction of light with matter based on the nature and chemical structure of the specimen. SpectrumWe develop the library to match the liberation size fraction Analyses every 1mm2 1 meter of NQ core = 35 000 analysis data Crystal size detection : 0.1 micron

May 1, 2013

By A. Burkert, A. E. Hajj

"An information system has been developed for the use of companies considering developing a new mine which may be liable to secondary sulphide ignitions or by existing operations. The system uses the Comdale X expert system to analyze information about a particular mine. The system will indicate whether the mine is likely to experience ignitions and what precautions can be taken to reduce or prevent their occurrence. The advantage of an information system using expert system and artificial intelligence principles is that it can recommend action when there is an incomplete knowledge of all the system parameters. By interrogation of the user it can determine the state of knowledge and react accordingly. It is considered that such systems could be of significant use in mine planning for new and existing properties, especially where operators have limited expertise regarding secondary sulphide ignitions. IntroductionSulphide ignitions occur in the underground mines of several countries, including Australia, Canada, Finland, South Africa and the United States of America (1·3) and there has been a significant increase in their number and severity over the last decade(2.4). The basic causes of such ignitions are not well understood and man incidents are not reported or documented.Sulphide ignitions can pose a serious threat to the health and safety of mine workers and to the cost and efficiency of the mining operation (1-5). Byberg(6) described the three major problems associated with sulphide ignitions as:1. the force of the initial explosion can endanger workers and equipment;2. the intense heat of the ignition's flame front can endanger workers and equipment and may also ignite combustible material resulting in mine fires; and3. the sulphur dioxide produced by the ignition may be of such quantity and concentration to endanger workers, as was tragically demonstrated at Geco. In this incident in October 1985, a worker was killed at a position 2400 metres from the ignition point of a sulphide ignition at Manitouwadge, Ontario."

Jan 1, 1994

By Robert Marchand

_ North-western Quebec _ Bousquet mining district _ 21 M oz mining camp _ 100,000 t/yr (400 t/d) _ Shrinkage : 52 % _ Longhole : 40% _ Development : 8% _ 5 days/week _ 120 employees _Discovered in 1936. _12 changes of ownership. _Exploration & development : 1987 _Commercial production : 1990 _Shaft deepening : 1995 _Internal shaft : 1999

Oct 1, 2001

By L. B. Kilius

The composite cathode system based on Ce0.9Gdo.1O2_,5 electrolyte with a painted cathode was used for an intermediate temperature (500-700°C) solid oxide fuel cell. This cathode system was chosen due to its excellent thermal expansion match to the electrolyte, its relatively high conductivity (115 S cm-1 at 700°C), and its low activation energy for oxygen reduction (99 kJ/mol). It was found that the decrease of sintering temperature of the composite cathode system produces a significant decrease in charge transfer resistances to a level of 0.25 SI cm2. The conductivity measurements of porous samples produced values between 40 and 88 S/cm for porosities of 30-40%.

Jan 1, 2005

By G. Girard, A. Larouche, J. Colbert, G. Doyer

"The Direct Chill (DC) casting process uses water to extract heat from molten aluminium and helps to control the solidification process. Many factors such as the water flowrate, water distribution around the mould and water impingement angle have significant impacts on the solidification process. It has been noted that the chemistry variation of the cooling water is also an important factor that has a major impact on the presence of defects on the ingot. A significant change in the water quality can produce defects on the ingots such as cracks, bleedouts, or runouts. Understanding the impact of water quality variation on ingots is therefore essential to ensure good ingot production and reduce defects. This paper aims at describing a new approach to follow the variations of process water quality over time. It is an original and innovative method, which is still under progress. A water quality and stability index (WQSI) is under development to evaluate changes in the water composition based on water physico-chemical parameters. The index is calculated by comparing each of the actual parameters with historical values previously modeled by a statistical law. It is a dimensionless number having an adjustable weight factor for each parameter. The positive or negative contribution of each parameter, with respect to the water cooling capacity, is taken into account to calculate the WQSI. The current selection of parameters is based on knowledge from the literature as well as on empirical experience. When the developed tool will be mature, it could be used to track water variations upon time and anticipate problems, enabling proactive actions to ensure good ingot production.INTRODUCTIONFor many years, the impact of water chemistry on heat transfer, during DC casting, has been of great interest in the aluminum industry. Several papers have been published to demonstrate the correlation between water chemistry and heat transfer (Yu, 1985), (Gildemeister, 2014). Although numerous studies do present the effects of water parameters (i. e. hardness, conductivity, oil, and grease…) on cooling capacity under controlled experimental conditions, they do not reflect the strong interactions between the parameters and variations present in a casting center. Wells and Cockcroft also demonstrated that laboratory based studies are not fully representative of real heat transfer in an industrial casthouse, there are too many factors involved (Wells, Li, & Cockcroft, 2001). In this context, it becomes very difficult to obtain a quantifiable relationship between the capacity of water to cool the ingot and ultimately the performance of the cast."

Jan 1, 2016

By P. Diehl, M. David

"As shortage in the supply of mineral commodities become more probable, there is an increasing need for reliable and comparable reserve/resource data. It is therefore necessary to standardize the traditional classification procedure by quantifying the three basic criteria in resource evaluation: economic feasibility, geologic assurance and recovery. For the portion of fairly well documented deposits and as far as their geologic parameters are concerned, geostatistical methods can considerably improve the quality of ore classification. In respect of economic feasibility and recovery, approved geostatistical methods can be introduced directly into the classification procedure. The concept of geologic assurance, however, requires a new interpretation in terms of geostatistical error spread. As the ""risk"" in estimating an ore parameter is also a function of the respective block size, it is reasonable to define not only upper limits for the risk intervals for each class of uncertainty, but also block dimensions which reflect the typical stage of planning associated with the different ore categories. An algorithm has been developed to block out areas inside a mine or a large panel which satisfies the constraints of an ore category in respect of the risk intervals of a parameter and in respect of their size. The method has been computerized and is demonstrated on a massive copper-nickel deposit.IntroductionFacing an uncertain future with respect to the demand and supply of mineral commodities, both governmental authorities and the mining industries show an increasing interest in a useful framework for the assessment and classification of the remaining mineral resources"". This is reflected by the recently published appraisal and classification scheme of the United Nations as well as by the new or revised classification systems of the USA; Canada or Australia. Moreover there are various classification schemes which are currently discussed in major mining companies."

Jan 1, 1982

By John F. Kearney

After World War II Canada?s fledgling iron ore mining industry developed along the ill-defined Quebec / Labrador border near what became the town of Knob Lake and later renamed Schefferville. For about twenty-five years from 1954 to 1982 Schefferville was the epicenter of Canadian iron ore mining and the foundation of the Iron Ore Company of Canada. In about 1982 it all stopped, shut down, the miners moved away leaving behind a mining camp and a ghost town that have sat idle and almost deserted for the past twenty five years. The story looks set to change with new plans to re-establish the former mining operations in the historic mining camp. This paper outlines the proposal to reactivate the direct shipping iron ore operations in the Schefferville mining camp, and specifically the properties in Labrador owned or optioned by Labrador Iron Mines Limited (?LIM?), a wholly owned subsidiary of London Stock Exchange listed Anglesey Mining plc. The Schefferville mining camp is located about 1,000 km northeast of Montreal. There are no roads connecting the area to southern Labrador or to Quebec. Access to the area is by rail from Sept Iles to Schefferville, or by air from Montreal and Sept Iles.

May 1, 2007

By L. M. Scovell

The Internet and its related technologies will radically change the way that mines manage and control their maintenance, repair, and operating supply chains. The Internet is creating new distribution channels and offers new technology platforms with significant advantages over more traditional methods. Mines will have to re-evaluate both the strategies and the tactics employed in these areas. Mines will use e-commerce to integrate their maintenance, repair, and operating supply chains. The integration will extend beyond traditional trading partners to a worldwide network of communities with similar interests and goals. The changes will transform the way mines operate, lower mining costs, and thereby increase their chances of success in an increasingly competitive environment.

Jan 1, 2000

By William W. Shilts

"In carrying out a geotechnical survey of a proposed gas pipeline route from the Arctic Islands south to Longlac, Ontario, the Polar Gas Consortium contracted the drilling of several hundred 2- to 2D-m-deep boreholes in drift and bedrock. Samples from these holes were made available to the Geological Survey of Canada, where they were subjected to stratigraphic and trace-element geochemical analyses. The geochemical characteristics of the clay and sand-sized heavy mineral fractions of till samples from these boreholes have been summarized in a series of geochemical profiles.From the proposed pipeline terminus at Longlac northward to the vicinity of God's River in Manitoba, tills contain significant amounts of Paleozoic carbonate rocks and Proterozoic sedimentary rocks derived from the Hudson Bay basin and lowlands. Within this section, two sites were enriched in base metals, indicating the possibility of local mineralization of possible economic interest.From God's River northward to Seal River, Manitoba, no evidence of local mineralization was noted. The heavy mineral fractions of the tills are universally enriched in Mn-rich siderite thought to originate on or in the Paleozoic section of the Hudson Bay lowlands.From Seal River northward to Thelon River, near Baker Lake, tills contain only components originating west of the Hudson Bay sedimentary basin. Near the Keewatin-Manitoba border, all till is enriched in uranium, which probably originates in the ""young"" porphyritic granites underlying much of the region, and produces a distinctive airborne radiometric anomaly.At the Thelon River, multiple till sections are variously enriched in Cr, Ni, U, Cu and Mo in the vicinity of a distinctive aeromagnetic anomaly.From Thelon River northward, several coincident zones of chromium and uranium enrichment are found where the line of boreholes crosses east-west-striking belts of volcanic, ultramafic and sedimentary rocks of the Prince Albert Group.The results of this study indicate that till tends to have characteristic element associations or concentrations over each of several broad regions along the pipeline route. These are related both to large-scale bedrock associations and to largescale effects of glacial dispersal. In addition, the samples, collected more or less at random with respect to local bedrock geology, have intersected several small-scale geochemical anomalies that appear to be related to zones of mineralization of possible economic interest."

Jan 1, 1980

By Isabel F. Barton, J. Brent Hiskey

Chalcopyrite (CuFeS2) is the earth’s most abundant copper ore mineral, but is refractory to leaching with sulfates, chlorides, and other common lixiviants and oxidants. This has led to increasing research into alternative lixiviants for recovering Cu from chalcopyrite. Here, we review the leach kinetics of chalcopyrite in glycine, ionic liquids, and methanesulfonic acid, compared to baseline ferric sulfate and ferric chloride. Glycine (CH2NH2COOH) has long been used in applications such as biocatalysis and electroplating, and has recently been examined as a lixiviant for whole ores and concentrates of both copper and gold. It is nontoxic, biodegradable, and capable of strongly complexing Cu2+. Compatible oxidants are peroxide, dissolved oxygen, and ferric sulfate. Chalcopyrite leaching rate in glycine is chemical reaction-controlled, but the effects of grain size and the reaction orders with respect to lixiviant and oxidant concentrations and mass transfer vary. The use of ionic liquids as a leaching agent for chalcopyrite has been extensively investigated in recent years. This system is based primarily on the use of the imidazolium molecule (C3H5N2), which is a planar 5-member ring structure. This lixiviant has been applied to the leaching of chalcopyrite in the form of pure mineral, concentrates, and ores. Kinetics of ionic liquid leaching of chalcopyrite vary substantially depending on the type and concentration of ionic liquid. Methanesulfonic acid (HCH3SO3) is one of the newest lixiviants available in leaching, having only been examined in the last decade. It has been examined as a substitute for sulfuric acid, since it is less corrosive, is biodegradable, and breaks down to carbon dioxide and sulfate over time. The rate of copper leaching from chalcopyrite by methanesulfonic acid is controlled by diffusion and exhibits a strong dependence on oxidant type and concentration. Despite promising reaction rates and total extraction by some of these novel lixiviants, comparison with baseline ferric sulfate and ferric chloride systems makes it doubtful that any will be commercially viable in the near term. Only at very high reagent concentrations and temperatures, and/or very fine grain size, did any of the systems perform comparably to the much cheaper ferric chloride at extracting Cu from chalcopyrite. Most had similar overall reaction rates and total extraction to ferric sulfate, which is relatively common and cheap. However, the leaching kinetics of these novel lixiviants offer valuable insight into the dissolution behavior of chalcopyrite in various systems.

Jan 1, 2019

RISKGATE is an interactive online risk management system developed by the Minerals Industry Safety and Health Centre (MISHC; University of Queensland) to assist the mining industry in implementing continual improvement in management of major unwanted events so maximising health and safety performance. A comprehensive body of knowledge has been compiled from diverse mining industry experts for risk management of tyres, collisions, fires, isolation, strata underground, ground control open cut, explosions, explosives, manual tasks and slips/trips/falls. This paper presents an overview of the RISKGATE body of knowledge captured specifically for the management of unwanted events that stem from the handling and use of explosives (drill and blast) within surface coal mining operations. The knowledge presented is divided into a series of initiating events (listed below) within which there are further degrees of classification based on design, operation, and management concerns. Initiating events: ? Loss of control of explosives and associated chemicals in storage on site ? Loss of control of explosives and associated chemicals during transport ? Loss of control of explosives and associated chemicals during manufacture ? Loss of control of explosives and associated chemicals during handling and blast operations ? Loss of control of explosives and associated chemicals during disposal The system guides the user in generating substantive and leading-edge controls to assist in the design, management and reporting of drill and blast operations to meet stringent internal and external requirements. From a broader industry perspective, RISKGATE provides an environment for knowledge capture and knowledge exchange to drive innovation and best practice in the identification, assessment and management of risk. By capturing operational knowledge from industry experts, RISKGATE provides a cumulative corporate memory at a time of high personnel turnover in the coal industry.

Aug 1, 2013