Search Documents

By Deepak Bhadouriya, Saurabh Singh, Aditya Raj Suman

"An experimental study of chemically enhanced filtration and dewatering of fine coal slurry with and without additives was carried out. The experiment involved determination of effect of slurry concentration, additives (cationic, anionic and nonionic), filter area, filtration velocity, particle size and cake resistance on dewatering and filtration using vacuum filtration cell. Finally, the rate of filtration and dewatering and optimum amount of additives used were determined under suitable filtration condition. Overall, it was found that the filtration and dewatering characteristics were enhanced by increased slurry concentration, larger filter area and larger particle size. In addition of additives, the kerosene was found to be best for enhancing the filtration which yielded cake moisture reductions of approximately 17% by weight. At optimum dosages, the final cake moisture contents were reduced by 3.6% and 5.8% by weight using the appropriate surfactant and flocculent, respectively.INTRODUCTIONFor India, it is estimated that coal constitute a principal source of energy for the next several decades. It is majorly used at thermal power plants to generate electricity and also to a great extent in steel and cement industry. It has been observed that its consumption is increasing so as to meet the energy requirements of the country. It has been found that in a coal preparation plant; approximately 20-25 percent coal is of the mined coal of the range below minus 0.5 mm (28 meshes). Generally, this fine fraction is discarded due to its high cost of processing and further utilisatisation is very minimal. But with ongoing research and development for advanced clean coal technology, various new techniques have been evolved to maximize the utilization of available coal. In recent time technologies such as column flotation, cleaning of fine size coal to lower the ash content and low pyretic sulfur is feasible at high recovery value. But in various researches it is found that one of the biggest hurdles in utilization of fine coal cleaning technology by the coal industry is the economic dewatering of the fine clean coal product. Thus, until an economical and practical solution to dewatering of fine clean coal is achieved, the efforts devoted to developing fine clean coal technology will be wasted. In this paper an effort toward enhancing and developing the optimum technique of dewatering and filtration of fine coal slurry has been made."

Jan 1, 2016

By B. E. Halbert, K. T. Himbeault, S. L. Fernandes, R. L. J. Phillips, B. J. Topp

The Beaverlodge uranium mining and milling facilities operated from 1952 to 1981 with about 94% of the ore extracted from the main underground mine and 6% from smaller satellite deposits. Decommissioning work occurred from 1982 to 1985 involving periods of shutdown, salvage and reclamation. Transition phase monitoring, leading to eventual delicencing commenced in July 1985. Over the last 15 years, discharge from the tailings management facility (TMF) and a fresh water stream, impacted during the operational phase by tailings spills, has improved in water quality for most parameters of concern. Loadings to the environment of three key contaminants (radium-226, total dissolved solids, and uranium) have consistently been less than during the operational phase with radium-226 having the greatest variability. Outstanding environmental issues associated with the recovering drainage system formerly used for tailings disposal, are being addressed in an enhanced environmental monitoring program to commence in 2000. Changes in water chemistry and the natural re-introduction of aquatic organisms are issues of concern. In the meantime, application for release from selected satellite areas commenced in 1999. This paper reviews the issues which have arisen during the transition phase, outlines how they have and are being addressed, and provides a comparison of original and current predictions of the recovery process under way at the former Beaverlodge mine site.

Jan 1, 2000

By W. P. Campbell

Foreword At the outset, it should be stated that this paper does not pretend to present a panacea for the ills that 'frozen' wells are heir to, but rather is an attempt to bring to the attention of those whose special concern it is, a little theory and some facts, which have been brought to light recently, in connection with the problem of 'freezing' as it applies to naphtha-producing wells in the Turner Valley field, and to draw some conclusions that follow from the facts discovered. It should also be stated that the investigation is not to be regarded as in any sense complete, but in progress. Doubtless new facts will be brought to light from time to time which may modify present ideas on the subject, but whether favourable or contrary, these will be welcomed, as the purpose of the Department is to secure as complete information as possible of the factors contributing to 'freezing', since this must be the first step to an intelligent attempt to remedy or prevent its occurrence, if such can be done. It is possible, too, that the cause or causes of freezing may not be the same in all cases, but whether this be so or not will have to be determined later as new information comes to hand. Introduction One of the worries which must constantly confront the operators of gas-naphtha producing wells in Turner Valley-although all, fortunately, have not met with it-is the possibility of the occurrence of what is commonly called 'freezing' (going off production).

Jan 1, 1930

By L. Voisin, K. Mühlenbrock

A new pyrometallurgical process is proposed for cleaning complex copper matte and for recovering copper from copper scrap containing lead. In the process, a given amount of pig iron is added to the complex material under a reducing condition to produce two or three liquid phases at the equilibrium, depending on the content of sulfur in system, of copper-rich and iron-rich alloys, and matte, respectively. The novel process is proposed based on the experimental results obtained by performing laboratory scale tests in an electrical furnace at 1473 K followed by a quenching method on the final stage. The samples obtained from the experiments were analyzed by using Atomic Absorption Spectroscopy (AAS), Inductively Couple Plasma (ICP) and Carbon Infrared Spectrometry (CIS) techniques. The results were discussed on the basis of the distribution of lead as impurity in the miscibility gap where equilibrated phases coexist. According to the mass balance calculations, the elimination of lead into the iron-rich alloy phase as a harmless and smaller deposit might be feasible and the process proposed for cleaning the complex matte would be promising.

Jan 1, 2014

By W. L. Hunter

The preparation of coal for the commercial market is a study both varied and wide, and can be viewed from many angles and in different ways. This short paper can but touch upon the subject and is intended to discuss briefly preparation plants which in some cases would seem to be quite inadequate. The conditions confronting most operators are similar, inasmuch as the existing plants were not built specifically to prepare a product for the market of today, but rather of yesterday. The tremendous strides made in the field of combustion in recent years require that the product be of the highest grade procurable, and in a glutted and somewhat restricted market the buyer may be more pernickety than otherwise. These would appear to be the conditions of today. Where a mine is operated individually, better all-round results seem more readily procurable than in a consolidated effort where so many different conditions are sure to arise demanding cognizance, and in many cases requiring to be incorporated in the scheme of things. In the case of a number of mines being administered to form a central source, that source not having had anything to do with the bringing into being of the institutions over which it presides, we find some of the mines well equipped with facilities to properly screen and load the coal, while in others the facilities are not so good, but are doing their share towards delivering a product that will pass muster and in such quantities that they can be counted on.

Jan 1, 1930

By G. Danha, D. Glasser, D. Hildebrandt, N. Hlabangana

"In this work, we apply a method known as the attainable region (AR) technique in order to optimize the milling and leaching process of a low grade gold ore. No work on the application of the AR optimization technique has been done yet on a joint milling and leaching process. The advantage of the AR approach lies in its ability to simplify the optimization problem, as searching over a defined set for the maximum of an objective function is a fairly standard procedure. The objective function we selected was that of optimizing a linear function of the value of the recovered material minus the cost of both milling and leaching. Using the three variables (milling time, leaching time and recovery), we constructed a 3D plot and used it to obtain all the possible recoveries from the different milling and leaching times. The optimum for our chosen objective was then found by overlaying a contour plot of the objective function on the 3D plot. Our results show that the optimum was obtained at 90 % recovery with a profit value of 600, milling time of 30 minutes and leaching time of 1750 minutes.INTRODUCTIONAfrican countries are facing a general increase in demand for electrical power. In South Africa, the demand is now surpassing the supply from ESKOM, the main electric power provider of the country. This has resulted in load shedding strategies being implemented in many local communities in an attempt by ESKOM to cope with the high demand. A potentially better approach is to propose use of energy efficient technologies in the country’s largest power consuming industry; the mineral processing sector.In mineral processing, milling is the highest consumer of energy. The objective of carrying out milling is not merely to reduce the particle size of the feed material, but also to liberate the constituent minerals that make up an ore. This is done so that valuable minerals can be separated from the gangue, in downstream processes, such as leaching. However, the milling process is generally performed relatively poorly, and at a considerable expense in terms of electrical power utilization. Tomanec and Milovanovic (1994) estimated that milling accounts for more than 50 % of the total power used in the concentration process, but this can rise to as high as 70 % for hard or finely dispersed and inter-grown ores. Apart from being relatively wasteful of energy, the milling process is also inefficient with regard to mineral liberation because of the indiscriminate nature of the grinding force."

Jan 1, 2016

By W R. Honeywell

Two series of laboratory flotation tests were carried out to study the treatment of Faraday ore by two-stage flotation. First the acid-consumers and then the uranium minerals were floated. On ore ground in the Faraday mill grinding circuit, and using Faraday mill water in the flotation step, a recovery in the flotation concentrate of from 91 to 93 percent of the uranium was obtained in 45 to 50 per cent of the weight at a grade of 0.24 per cent U30s. The saving of acid in leaching the uranium-bearing flotation concentrate, as compared to leaching the whole ore, ranged from 30 to 46 per cent. The average over-all extraction resulting from flotation and leaching of the flotation concentrate was 88.1 per cent. The best collector for the acid-consumers was sodium oleate. Acintol F A-1 emulsion was the best collector for the uranium minerals, and, in the uranium flotation step, an acid pH in the slurry was found to be necessary. The reagent costs were estimated to be 22 to 26 cents per ton of ore.

Jan 1, 1963

By Mathieu Dubé

Good mechanical strength of green iron ore pellets is required to avoid breakage and excessive deformation during their handling and further processing. However, green balls with good resistance to handling are often too plastic, which impacts the bed permeability in induration furnaces. Measurements of plasticity, bed void fraction and green ball sphericity as well as bed permeability were carried out on various samples of green iron ore pellets having different mechanical strength. Results show that bed void fraction, sphericity and permeability all depend, to some extent, upon green ball mechanical strength (plasticity). Understanding and controlling the mechanical strength of green iron ore pellets would then help to maximize both the productivity of the induration process as well as the quality of fired pellets through a more stable firing process. Results of research work carried out at COREM, with the objective of improving green ball characterization methods, are presented in this paper.

May 1, 2007

By W. Curlook, L. M. Pidgeon

THE PURPOSE of this investigation was to study part of the ternary system Co-Fe-S. Jensen ( 1) established the solubility limits of sulphur in pyrrhotite. The compound with 61.7 per cent Fe, corresponding to a formula Fe12S13, was found to melt congruently at l,192°C. Hulsmann and Weibke(2) determined the Co-S phase diagram from O to 35.2 per cent S. The solubility limits of sulphur in the com-pound Co(l-x)S were not determined. The initial object of the present in-vestigation was to determine the composition at which the compound Coci-xiS melted congruently. Once this was ascertained, it was decided to investigate the ternary system Co-Fe-S from the region of 100 per cent Co(1-x) S to the region of 100 per cent Fe12S13.

Jan 1, 1953

By G. Herget

"A brief visit to European longwall mining operations in potash showed that retreating longwall mining provides a very attractive alternative to room-and pillar mining, especially in areas with bad roof, narrow seams and areas with high ground pressures. Mines de Potasse d'Alsace, France converted all potash operations to longwall mining in 1980. Recovery rates per panel vary between 75o/~ to 85% which compares very favourably with Saskatchewan values. Ground pressure in Saskatchewan are comparable to those of some of the deposits in Europe, but the presence of water in the hanging wall of Saskatchewan orebodies has to be given serious consideration. However, given the mining experience in Saskatchewan and the improved technology f or laboratory and field investigations, a review of present mining practice in Saskatchewan is desirable. IntroductionLongwall mining is practiced widely in coal mining and allows complete mechanization. It is applicable at great mining depth, in thin seams, weak roof and has been applied recently even to coal bed s dipping more than 65 degrees. Ideally this system allows complete extraction of an orebody. However, with high mechanization and emphasis on obtaining high outputs per man shift, extraction ratios rarely reach more than 80010 per panel.France, Spain and the U.S.S.R. have had longwall operations in potash for some time and a brief description is given below. Two of the operations were visited and the Russian operation is described based on German literature"

Jan 1, 1986

By J. R. Goode

"Canada developed pioneering rare earth solvent extraction methods to recover the rare earths and thorium as by-products of uranium recovery operations in Elliot Lake, Ontario, and was a major supplier of these key elements from about 1960 until 1990. At one stage, Elliot Lake was supplying perhaps one third of the world’s yttrium as well as much of its thorium. This paper reviews the development of Canada’s early rare earth and thorium production facilities. INTRODUCTIONThe rare earths and thorium were first identified in the early 19th century but were little more than curiosities for the next century. However, in the mid-1960s the invention of rare earth-based phosphors for the cathode ray picture tube used in colour television sets launched a major demand for certain rare earths.The use of thorium as an alloying agent in aircraft and missiles grew rapidly in the late 1950s. In the same period, demand for uranium for both weapons and power production soared. Also in the late 1950s, the Elliot Lake uranium-thorium-rare earth deposits (also known as the Blind River deposits) were discovered. This conjugation of events led to uranium production in the Elliot Lake camp, quickly followed by the co-production of thorium and, later, the rare earths.Uranium production in the Elliot Lake camp continued from 1955 to 1996. Thorium was produced continuously from 1959 to 1969. Rare earths were produced, intermittently, from 1965 to 1990. Complete production records are not readily available but unquestionably Elliot Lake made a significant contribution to world thorium and the rare earth production. This paper, presented earlier in an abbreviated form (Goode, 2012), is intended to present as much of the information that is available."

Jan 1, 2012

By B. S. Ignasiak, Dennis Carson

"Laboratory study of the behaviour• of binary coal blends shows that coke strength is more closely dependent on the distribution of ""reactive"" oxygen in the parent coals than on their proximate, elemental or petrographic compositions, and it also appears possible to qualitatively predict coke strength from information about reactive oxygen. Proceeding from this recognition, experiments were carried out to test the possibility of preparing metallurgical cokes from binary blends in which non-caking hvb coal was substantially freed of reactive oxygen by prior heat t1•eatment under controlled conditions. The results indicate that such blends can yield surprisingly strong cokes and that coke strength may be amenable to further improvements by modifying the size distribution of the pre-heated component and the rate at which it is charred."

Jan 1, 1976

By Jose R. Hernandez-Aguilar

"This paper revisits data from previous studies (Hernandez-Aguilar, 2010, 2011) to better understand the link between metallurgical performance and bubble size (Db) in the collection (pulp) zone of full-scale flotation systems. To obtain conclusive evidence exclusively related to the collection zone, the experiments were designed in those studies to control both the bubble generation method and the influence of the froth zone on the overall metallurgical performance in industrial and pilot-scale flotation columns. The results showed that generating small (1 mm) bubbles had a significantly higher beneficial effect on the recovery of coarse (> 75 µm) particles compared to the effect on fine (< 16 µm) particles. It was observed that, under certain practical conditions, the recovery of liberated coarse particles was close to zero, but could be recovered almost completely by reducing bubble size. The evidence revealed an apparent inconsistency of the so-called “k–PSb” model: at constant froth recovery, increasing Sb did not always result in higher recovery, as the model predicts. Overall, the evidence showed that it was not the Sb but the bubble size that proved to be a more reliable link to metallurgical performance. Only under highly suboptimal bubble size conditions (Db = 3 mm) did the froth zone seem to play a role, possibly reflecting an effect of pulp-zone bubble size on froth stability. However, for the most part, both the bubble generation method and the froth zone played inconsequential roles. An empirical model that better describes the kinetics of particle collection is proposed.INTRODUCTIONStudies showing the link between metallurgical performance and the interactions of bubbles and particles in the collection (pulp) zone of industrial flotation systems are scarce. A common belief among a number of mineral processing practitioners considers that “small” bubbles are favourable to recover “small” particles and that, conversely, “larger” bubbles are more efficient at floating “coarse” particles. However, perceptions like this are often substantiated by anecdotal evidence rather than by rigorous data analysis. What is the optimum bubble size for a particular case, how operating conditions can be adjusted to control a target bubble size, and whether the bubble size needs to be changed in the first place to optimize the operation of a flotation plant are questions that usually remain without solid answers.The studies reported by Hernandez-Aguilar (2010, 2011) were, in part, performed to test the effect of bubble size on flotation response and, thus, help address some of the above questions. The focus of the studies was to optimize the metallurgical grade-recovery performance of the Cu-Mo separation plant at Teck’s Highland Valley Copper mine (HVC). The outcome was compelling and significantly valuable: consolidated production data showed that in 2008 – the year when the recommendations from the studies started to be implemented – the Mo plant recovery was 89%, and gradually increased to 92% and 94% in 2009 and 2010, respectively, along with an increase in Mo concentrate grade. (Note: these production figures were not included in the publications quoted above; however, they were shown during an oral presentation at the 43rd Annual Meeting of the Canadian Mineral Processors in 2011.)"

Jan 1, 2016

By Horst Konig

This paper illustrates that, with the application of new processes, smaller steel plants using local raw materials can be economical and advisable. It also introduces the problems connected with the direct reduction processes, which use non-coking coal or gas as reducing agents, and which are employed in connection with conventional reduction to produce excellent results. Electric smelting is also discussed, and some practical examples of operating plants are given.

Jan 1, 1970

By B. Tiryaki, M. Ayhan, O. Z. Hekimoglu

Coal shearers are one of the major sources of dust and fines in underground coal mines. Despite considerable research investigations, no comprehensive in situ investigations coupled with extensive laboratory studies on the effects of drum design on generation of dust and fines have been found. It may be for this reason that many major shearer drum manufacturers persistently employ a certain drum-lacing pattern on current coal shearers, which is believed to cause excessive dust and fines in coal mines. This paper shows how respirable dust and fines are minimized under near-identical conditions when the drum lacing pattern was changed from a triple-tracking to a single tracking arrangement. A series of laboratory trials simulating in full scale the practical cutting action of tools was followed by extensive long-term underground trials during production operations in OAL (Cayirhan) Lignite mine in Turkey. The results are presented and discussed, and recommendations for proper drum-lacing in terms of respirable dust and fines are made.

Jan 1, 2002

By Adam Chrzanowski, Eugene E. Derenyi, Peter Wilson

"The rapid growth of the mining industry in Canada necessitates a reevaluation of existing mining surveying techniques and the development of new methods. In this connection, the Department of Surveying Engineering at the University of New Brunswick initiated a research program, and the major points of investigation conducted to date are as follows: 1. Based on practical experience and theoretical studies, all factors influencing classical shaft-plumbing procedures were analyzed. Refined methods were developed to increase accuracy. 2. The performance of electronic and optical distance-measuring instruments in underground conditions were investigated. In this connection, test measurements were made in various mines, employing four types of Tellurometers, two models of Geodimeters and a proto-type optical range-finder. 3. Tests were conducted and methods developed for the mapping of large underground chambers by photo-grammetric means. The aforementioned points are discussed at some length in the paper. The authors have also indicated areas where further research is needed and suggested ways and means to improve and modernize mining surveying as a whole throughout Canada."

Jan 1, 1967

By W. D. Watson

"Early in mine development at Quintette Coal Limited major problems were encountered with the fleets of primary equipment which seriously hampered production. These major fleets (cable shovels, hydraulic shovels, hydraulic drills and electric trucks) have consequently been the focal point of maintenance efforts. Some were prototypes in the Canadian mining scene and brought with them new concerns to test their skills. The problems were studied and the category and areas which were having the greatest impact on the reliability of the equipment were determined. Once defined, priorities were established and a program was initiated which was designed to accomplish a resolution. Resulting from implementation of this systematic approach, over the past three and one-half years, the fleets are now giving good reliability and industry standard availabilities. Along with these significant achievements, cost per operating hour on some of the equipment fleets has decreased substantially and continue a downtrend through 1987. This paper identifies the problems and describes the resolutions. IntroductionIn the early years of the mine development, Quintette Coal Limited (QCL) experienced production shortfalls due to problems with the major excavator and haulage fleets. A large fleet of hydraulic excavators had been purchased, and QCL was among the first northern users of all hydraulic blasthole drills. They were also using some prototype equipment and encountered problems which were not common on other types of equipment or were unknown.Because of these unique problems and lack of experience from other mines to draw on, an analytical approach was taken to areas and associated causes of the delays affecting the availability and reliability of equipment. This was done by dividing the equipment downtime into seven classifications of delays, i.e. maintenance, electrical, hydraulic, mechanical, damage, service and preventative maintenance, and tires; and then each was expressed as a percentage of total downtime. Subsequently each of the delay classification was divided into categories e.g. electrical to six categories - wheel motors, main alternator, relays, cards, no propel, lighting and 24 V system. Then, the basis for further study had been established.From this preliminary analysis of historic records, it was possible to determine the areas which were causing the majority of the downtime. These areas were then analyzed to evaluate causes and to determine possible solutions to the problem s. This paper addresses the major fleets, their problems and eventual solutions. Plea se bear in mind that the over-all objectives were to increase physical availability and reliability."

Jan 1, 1988

By Bob Butler

Brunswick Mine has been involved in a comprehensive research program investigating site specific aspects of thiosalt management to eliminate its adverse environmental effects. Minimum annual reagent cost estimates for thiosalt treatment using hydrogen peroxide and sodium hypochlorite are $400K and $1.5 million respectively. Also, minimum costs for the use of bicarbonate to buffer the pH depression associated with thiosalt oxidation in the receiving environment is in the order of $400K annually. A design of experiment (DOE) research program identified that natural UV radiation, temperature, DO and water chemistry are key factors influencing the natural oxidation rate of thiosalts within Brunswick?s water management system. A DOE surface response model was used to describe the thiosalt oxidation kinetics, which were then used to develop a predictive oxidation model for thiosalt and pH control of the mill?s reclaim water system.

Nov 1, 2002

By C. O. Aksoy, P. M. Ozfirat, M. K. Ozfirat, C. Tatar, C. Pamukcu

"Temporal and other factors contributing to the occurrence of occupational accidents at an underground coal mine in Turkey between 1992 and 2000 have been analyzed. The time period of the study spanned the transition from hand-worked mining methods (1992 to 1996) to hand-worked mining methods and mechanized mining methods (1997 to 2000).The mine selected for the study employed an average of 5,835 men per year on three separate eight-hour production shifts for 302 d/y (Sundays are not worked, and there are 11 holiday days per year). Production on an annual basis averaged 190,000 tons per year between 1992 and 1996, and 300,000 tons per year between 1997 and 2000.The purpose of the study was to determine which, if any, of the factors studied contributed to the occurrence of accidents so that the mine could take the necessary steps to reduce the risk to the workforce. Regression analysis was used to determine the strength of the relationship between each factor studied and the number of occupational accidents.The strongest relationships observed were between the age of the employee, the day of the week, and the total yearly labour."

Jan 1, 2006

By Y. Q. Li, Z. C. Shen, C. H. Zhao

The dynamic properties of the KYF-320 flotation machine which is one of the biggest flotation machines in the world were tested and then verified by the computational fluid dynamics (CFD) simulation. Aeration rate testing results suggest that he effect of circulation holes on the fluid state in the flotation cell becomes gradually smaller when the impeller speed is greater than 107 r/min. The dispersion degree of air increases with the increasing impeller speed and decreases with the increasing aeration rate, and it increases slightly when the impeller speed is greater than 107 r/min. The air holdup increases and then decreases with the increasing impeller speeds and aeration rates, and a maximum value of air holdup is shown at impeller speed of 107 r/min with a value of 12.28%. CFD simulation results are in good agreement with these testing results. Industrial-scale test was carried out using this 320 m3 flotation machine for the flotation of Cu ores. The results show that Cu content increases from 0.06% of crude ore to 1.26% of concentrate, and the S content increases from 0.39% of crude ore to 24.83% of concentrate. Moreover, using this flotation machine 5.88% of power is saved compared to other type of large flotation machine.

Jan 1, 2015