Search Documents

By Johnstone RD, Rattenbury MS

RACE Quartz-calcite veins containing Au, As, W, Cu, Pb, Zn and Fe cross-cut Alpine Fault- related structures in the Alpine Schist of South Island, New Zealand. These veins, and some other related veins have been deposited by metamorphic fluids at 250¦C to >320¦C at pressures of a few hundred bars. The fluids were very variable in composition, with 0 to 50 mole % CO2 and 2 to 18 wt. % NaCl equivalent. Penetration of hot metamorphic fluids to shallow levels in the crust was facilitated by rapid uplift of hot rocks at a compressive plate margin. Fluid immiscibility at shallow levels caused concentration of salts and metals into the aqueous phase. Gold precipitation was caused by reduction by pelitic country rock and/nr dluILion by other aqueous fluids.

Jan 1, 1987

By J-P Franzidis

The Floatability Characterisation Test Rig (FCTR) is a self-contained, highly instrumented, mobile pilot plant. It was developed as part of the AMIRA P9 project, primarily to determine ore floatability characteristics and to develop and validate flotation plant modelling, scale-up and simulation methodologies. This paper describes the use of the FCTR in validating the AMIRA P9 flotation model and modelling methodology. In 2001 the FCTR was installed and operated in parallel with WMCÆs (now BHP BillitonÆs) Kambalda Nickel Operation. The FCTR was operated using four different circuit configurations of increasing complexity. Metallurgical surveys, cell characterisation measurements and batch flotation tests were performed around each circuit. This allowed the calibration of a number of flotation models using a combination of data from one, two, three or four circuit configurations. The calibrated flotation models were then validated using predictive validation. To do this, data around a further five FCTR circuit configurations were collected (three of which are presented in this paper). The performance of each of the five circuit configurations was predicted using JKSimFloat V6.1 and the parameters from the various calibrated flotation models. The predicted performance was compared to the experimentally determined performance of each circuit. The validation of the AMIRA P9 model was shown to be largely successful except in the case where the reagent addition (depressant) to the validation circuit was different to that in the calibration circuits. The results also provided information regarding the required complexity of the calibration circuit and how many calibration circuits are required to obtain an accurate prediction of circuit performance. These results have increased the confidence in the AMIRA P9 flotation modelling methodology and have provided important information on what data must be collected to allow the accurate prediction of plant performance using the floatability component modelling approach.

Jan 1, 2007

IT is most remarkable and valuable property of mediurn and high carbon steels that they should be so susceptible to heat treatment, the wide range of variability in tenacity, ductility, etc, due to the normal influence of the carbon in the untreated material being enormously inereased thereby.The physical properties of steel and other metals are much more closely related to their structure than to their ultimate analysis.For instance, we may by chemical analysis determine the carbon content of a steel to be 0.5% ; but this information alone is insufficient to enable us to say what are the physical properties of the metal.Such a steel may possess 11 tensile strength of anything from 35 tons per sq. in., with much ductility, up to 80 tons per sq. in., with practically no ductility, according to its heat treatment. A microscopie examination, on the other hand, would show the structural composition of the steel, from which its physical properties could be approximately deduced. From this it will readily be understood that the microscope has played an important part in the development of modern rnetallurgy, and to-day it is in daily use for the examination of metals and alloys in the laboratories of most works dealing with the rnanufaeture and working of metals.THE IRON-IRON CARBIDE EQUILIBRIUMTo understand fully the mode of occurrcnce of the different constituents of a knowledge of the Iron-Iron Carbide equilibrium diagram (Fig. I) is essential to heat-treat steel successfully and to interpret microstructures correctly such a knowledge isabsolutely indispensable.A portion of the Iron-Iron Carbide Diagram, dealing with steels below 1000 and containing up to 1 carbon is given below.It should be noted that the diagram deals entirely with pure carbon steels, and does not indicate the influence of the usual so-ealled "impurities" present in all commereial carbon steels...

Jan 1, 1926

By D V. Boger

The use of chemical additives to initiate such processes as particulate separation through flotation or dewatering through flocculation, is common in the mining industry. The dosing of additives is none the less poorly controlled from a process control viewpoint and it is perhaps fortuitous that over-dosing or misuse of chemicals is rarely catastrophic to the production cycle. In many cases, such events would go undetected if it were not for economic considerations. Recently, the advent of orebodies with finer mineral disseminations and the push for greater efficiencies in both production and tailing disposal have resulted in the need for greater control of the dosing and utilisation of chemical additives. The need to grind at higher pulp densities and to finer sizes and to dewater to higher solid contents are but two examples that require a more stringent understanding of the true role of additives in controlling the rheology of suspensions and the influence of additives on the surface chemistry of particles. The inter-relationship between the surface chemistry of particles and the role of additives in controlling suspension rheology is now well understood for systems in which the average particle shape in the mixture is spherical or close to spherical. Luckily, this is the case for a large number of systems in the mining industry and the true role of typical additives in these systems will be explored. Difficulties arise for suspensions containing clays or other platey or needle shaped minerals and in many cases, quite small quantities of platey minerals dominate the rheology of suspensions. The role of additives in controlling the rheology of asymmetric particle systems is more complex but the effect of the additive in changing particle alignment in solution is the key to understanding suspension behaviour. The manipulation of the rheology of asymmetric particle systems will also be explored.

Jan 1, 1998

By M Noy, P Hawkes

Improvements in the drill and blast process can impact on loader performance in a number of ways. The main effects being improved loading cycle times, less non-productive cycles such as oversize removal, clean-up and face raking and better bucket fill factors. The impact of improved loading cycle times on the overall cost and productivity of the load and haul cycle is very much dependent on the loader truck match and the management of the haul fleet. Previous work has shown that a 20 per cent improvement in dig cycle times may only lead to three per cent or less improvement in the overall productivity of the load and haul process. However, improving the mass loaded per pass by five per cent will lead to a five per cent improvement in productivity for any given haul fleet situation, assuming sufficient truck capacity. Work by Orica Explosives at Lab ChrysotileÆs Thetford Mine, Quebec, Canada showed a relationship between muckpile fragmentation and truck payload. With this in mind, work was carried out to determine the effect differing muckpile fragmentation distributions can have on excavator bucket fill factors. This work was performed in the laboratory to a 1:100 scale. Nine different distributions were used. These were characterised by the Rosin Rammler parameters, xc the characteristic size, and n, the uniformity index. The values of xc and n used were modelled on those previously measured at a Sydney quarry. For the range of distributions measured, it was found that the fill factors were lowest at a low characteristic size and a high uniformity index and highest at a high characteristic size and a low uniformity index. In other words the best fill factors were achieved with a more dispersed muckpile distribution with a larger characteristic size. The difference in fill factors was 16 per cent indicating that controlling the drill and blast process to produce a specific muckpile distribution can have a significant impact on the overall cost-efficiency and productivity of the load and haul process. Field measurement by Orica Explosives at a quarry in Canada supports this conclusion showing improvements of up to seven per cent in average bucket load by either increasing the characteristic size or decreasing the uniformity index of the muckpile.

Jan 1, 1999

By Masszi D

INTRODUCTION The association of methane with coal has been known almost since coal was first mined and in general it has been considered the curse of underground coal mining. Historically, most of the effort to handle this methane has been directed at diluting it to a safe level and preventing an explosive mixture of methane and oxygen from forming in any part of the mine. This is generally achieved by in-mine activites. This approach has two principal drawbacks, the severity of which are dependent on local conditions. The first is that the activity associated with the handling of the methane is undertaken in the mine and there- fore competes with the mining activity for the limited space available. The second drawback is that the whole methane handling activity is generally a cost to the coal because methane is so diluted that it cannot be used. With the value of energy increasing thi; second drawback is gaining importance so th.u several mines in Europe and North America ;it,, now installing systems to recover the methane in a useful form. Two approaches are

Jan 1, 1982

By Monette J. C, Nulty J. H

High temperatures and pressures are required to obtain acceptable stripping rates. Higher chemically induced stripping rates could reduce the need for higher temperatures which lead to cyanide losses. The higher rates could lead to lower carbon inventories and higher gold production. This paper reports laboratory and continuous test unit data which strongly suggest that the preceding can be achieved. New stripping agents demonstrate efficient stripping under conditions of cyanide depletion such as after carbon acid washing. Stripping times for gold and silver can be reduced by at least half compared to caustic cyanide through the use of these novel substances.

Jan 1, 1991

East Nelson and Marlborough, in the northeast of the South Island, contain a wide variety of metallic minerals, including gold, silver, copper, chromite, antimony and scheelite, but no sustained metallic mining industry has evolved. Gold was the most sought-after mineral during the first century of European settlement and numerous discoveries were made but these failed to live up to expectations. While traces of gold are widespread in east Nelson, including in quartz veins in Nelson City, no payable deposits were found. In Marlborough the probability of a gold discovery had initially seemed remote but all this changed with the finding of rich deposits in the bed of the Wakamarina River in 1864, which provided a much-needed boost to the provincial economy. However, the decline of gold mining in Marlborough began virtually as soon as it had commenced. Extensive floods in 1865 hastened the exodus of miners to the profitable new fields of the West Coast.

Jan 1, 1993

By Carthew SJ

The early period of South Australia's mining history was dominated by Cornishmen as large numbers of miners and their families migrated to escape closure of the Cornish copper mines. Records show that Carthew families migrated from Kent and Cornwall to South Australia. Those from Redruth, Cornwall, were miners and their family history provides an insight into the condi- tions under which early miners lived and worked. Carthews are one of the oldest surviving mining families in South Australia and their movement pattern has been typical of many other early Cor- nish mining families.

Jan 1, 1987

Solid Energy New Zealand Limited (æSolid EnergyÆ) is a state-owned coal mining company, producing 4.0 Mtpa from a number of opencast and underground mines in the Huntly, West Coast and Southland regions in New Zealand. The company currently exports 2.1 Mtpa of coking coal. Exports are expected to grow strongly over the next five year as the company expands production into new semi-soft and thermal coal reserves. Domestic coal demand is also expected to grow strongly, particularly in the North Island, as the Maui gas field reserves diminish, and thermal coal becomes more important for electricity generation and meeting the energy needs of forest processing and other industries. Solid Energy is expanding and developing its risk management practices across all areas of the business: strategic planning û extensive use of scenario analysis and probabilistic modelling over a 20 year period; investment decisions û development and application of a rigorous six stage æProject Assessment GuidelineÆ process for all new mine developments; geological and geotechnical risk assessment techniques û use of best practice techniques including seismic surveys; financial risk management û a dynamic approach to hedging based on effects based analysis of Cash Flow at Risk analysis against preset risk tolerances; risk financing û the use of a captive insurance subsidiary, and the experiences of a small coal company seeking to obtain insurance cover on a æhardÆ international insurance market; and integrated risk management û the challenges of trying to implement a broad integrated risk management approach across the company, that supports implementation of strategic objectives as well as meeting æcompliance or legislative basedÆ risk management requirements.

Jan 1, 2003

By Madgwick J, Pracejus B

The microbial, microaerobic, biodegradation of cryptomelane-rich and pyrolusite-rich samples of manganese oxides was studied in repeated five-day static batch cultures over II weeks. Manganous ion was leached/reduced faster from the cryptomelane-rich samples (average 510 mg Mn2+/1/d) than from the pyrolusite samples (average 442 mg Mn2+/1/d).Cultures contained 20 per cent (w/vl) manganese mude, five per cent (w/v) molasses nutrient and the end-of-batch bacterial cell numbers were approximately 1010 cells/ml. The cryplomelane-rich sample incubates became more acid with time than the pyrolusite-rich incubates. The breakdown of pyrolusite proceeds in a relatively uniform way, while cryplomelane indicates a stepwise destabilisation.

Jan 1, 1992

By D Burgess

Since the days of mandatory high cost pilot plant testing in 6 ft + 2 ft SAG mills autogenous griding/semi-autogenous grinding (AG/SAG), mill specific energy is now calculated by various empirical formulae and pilot testing carried out in small laboratory mills. Barratt (1989) described a method using Bond Indices than adding a single factor of 1.25 to arrive at the AG/SAG specific energy. In 1991 the Canadians developed the SAGPower Index (SPI), test using 2 kg of material in a 300 mm diameter mill. This test has been further developed by Starkey, Hindstrom and Orser (2006). This test now includes a Bond Ball mill work index test.The Macpherson test is still being offered by some testing facilities. This dry test requires at least 180 kg of material.Morrell (2004) formulated an AG/SAG specific energy generator based on a drop weight index Value (DWi). This DWi value is related to the Ab parameter and the material specific gravity. Morrell reconfigured the BondÆs Third Theory formula to cause extra power requirements to be inputed. This technique incorporates the material specific gravity (SG). The AG/SAG specific energy values produced using this method are susceptible to higher values of crushing and rod mill work indices.This paper offered describes a more simple method to generate AG/SAG specific energies. This programme incorporates Bond work indices, the JKMRC parameter Ab measuring impact breakage and the parameter ta measuring the abrasion rate, then employs a series of efficiency values nominated for each transition size (AG/SAG T80). These efficiency values have been compiled over the years from actual operating plants and documented reports.CITATION:Burgess, D, 2012. A method of calculating autogenous/semi-autogenous grinding mill specific energies using a combination of bond work indices and Julius Kruttschnitt parameters, then applying efficiency factors, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 37-44 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

My purpose here today is to introduce an element of democracy into this seminar. In my experience, the mines of Australia can be divided into two categories; those that pay and those that don't. As far as I can ascertain, every other paper being delivered at this seminar concerns mines which come into the first category, or at any rate are close enough to it for the promoters to be able to afford an expert's valuation.

Jan 1, 1989

By L Huang

"Successful rehabilitation of tailings landforms of tens to thousands of hectares in size at base metal mines is critical to mining companies’ ‘social licence to operate’. Rehabilitation technology used is closely related to both the economic sustainability of the mining company and the ecological sustainability of the mined environment. Conventional technology to rehabilitate mine waste landforms is costly and constrained by the availability of soil (to reconstruct root zones) and clay materials (to reconstruct compressed layer). Depending on mine waste properties and site-specific resource availability, it is not uncommon to cost A$0.1–0.5 M/ha for the establishment of conventional cover systems over mine waste domains, which often accounts for large proportion of the total closure costs. This can lead to costs approaching several hundred millions dollars for rehabilitating larger tailings and acidic waste rock using conventional cover systems.The present extended abstract proposes a suite of new technologies to tackle the problems outlined above and discusses critical factors in successful rehabilitation from substrate levels to the whole landform performance, in two key aspects:in situ engineering of tailings soil to offset/reduce materials requiredin situ chemical engineering of massive hardpan layer through alkali-activation and mineral gel cross-linking network mechanisms to encapsulate reactive tailings and achieving sustainable hydro-geochemical stability in root zones.This aims at functionally replacing the roles of the compressed clay layer and capillary breaks in conventional covers. These technologies would improve both the economic and ecological sustainability of mine waste rehabilitation, thus addressing the triple-bottom line of mining and mineral processing industries not only in Australia but other countries.CITATION:Huang, L, 2016. Emerging technology for economic and ecological sustainability in the rehabilitation of metal mine tailings, in Proceedings Life-of-Mine 2016 Conference, pp 128–131 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 28, 2016

AND INTRODUCTION The Lochiel coal deposit, a large Tertiary soft brown coal deposit in the mid north of South Australia, is currently being investigated by the Electricity Trust of South Australia (ETSA) as a potential source of fuel for a base load power station. Feasibility studies indicated that the proposed dragline method of overburden removal was viable but economically sensitive to both highwail and dump batter angles. The unusual properties of the unconsolidated overburden sediments and the groundwater regime posed a number of intimately related hydrogeological and geotechnical questions which were addressed before and during the excavation of a trial pit. All strata at Lochiel are of soil strength, and artesian aquifers occur above and below the coal. From the initial evaluation of the deposit a number of hydrogeological questions were defined. These related to the rate at which the pore pressure in the silts is reduced by dewatering, the extent of the reduction in pore pressure due to prestripping, and the feasibility of dewatering and depressurising carbonaceous silty sand sequences. The site of the trial pit was selected to answer these and other questions from the basis of a detailed geological, hydrogeological and geotechnical understanding. The trial pit dewatering system simulated a full scale mine dewatering system and included ten pumped wells, twenty drainage wells, and nearly 400 monitoring instruments. It operated from September 1986 to June 1987. The excavation was carried out between February and May 1987.

Jan 1, 1988

By Ross J. F

A pillar 'is a block of coal left in the first working of a coal seam for the purpose of supporting the superincumbent strata in such a manner that the winning out roadways will be safe to traverse by men and by the coal transport system.PRINCIPLES OF PILLAR EXTRACTION.The size of a pillar is chiefly dependent on the depth of cover, and in a lesser degree on the nature of the coal, or the condition in which the seam has been laid down. In a seam at 1,100ft. depth of cover, and assuming a spec'ific gravity of 2.5 overall for the cover strata, a pressure of 1,200lb. per sq. in. is the loading on the top surface of the coal seam before mining begins.When mining commences, and as the pillars are formed, an increased load is imposed on the coal left in the pillars, according to the percentage of coal extracted in the first working. Thus, if 25% extraction is taken in the first working, the load on the pillars is theoretically increased from 1,200lb. per sq. in. to 1,600lb. per sq. in. over the area mined. If this state of things went on indefinitely it would not be possible wholly to extract a pillar because of the extreme pressure tliat would be thrown on the diminishing portion; but, fortunately, another element, that of time, enters into and assists the process of extraction.If the superimposed strata were of an entirely plastic nature, this time factor could not operate, as the cover weight would settle instantly on the remaining portion of the p'illar and finally overwhelm it. The cover strata above a pillar generally have a certain rigidity which does not allow the superimposed weight to settle instantly on the pillar fraction, and it requires a period of time to elapse before the extra weight is felt by the pillar.The time factor varies widely, and is governed entirely by local conditions; it can only be determined by experience gained on the spot or in close proximity to the area of operations. It is dependent on the strength of the strata and its characteristics under bridging conditions.It is, therefore, logical to assume that the more rapidly a pillar can be extracted the greater will be the safety factor and also the percentage of recovery of coal.Up to the present time, the operation of the extraction of pillars in this country has been, with a few exceptions, a manual one, and before mechanization of Collieries can be fully accomplished, the process will have to be performed mecharrically.

Jan 1, 1947

By M Coleman

Information is a key ingredient for successful mineral exploration and development. Whether identifying potential exploration localities from a map, interpreting technical reports or searching a register for operators past and present, the common aim is a parcel of information from which the enquirer can make a decision. Traditional information gathering often requires days or weeks of manual research, studying maps, files, reports etc, before consolidating the results into an investment proposal. In recent times, such methods have largely been replaced by Information Technology, making the process much faster, easier and more centralised. However, notwithstanding some very successful technology implementations, the general rush to computerise everything in sight has left many organisations struggling to cope with the management of large volumes of diverse information. Information management is now recognised as the most important factor in determining the success of information technology implementation. The Northern Territory Department of Mines and Energy (DME) has established a detailed information management strategy to underpin the rapid advance of computer technology within the organisation. A broad base of timely and reliable information is gradually becoming more accessible. It is envisaged that the availability of combined spatial, textual and scientific information will provide a sound basis for decision-making within the Department and the mining industry at large. Although information held by DME will be available at all times (24 hours on-line), its security and confidentiality will be guaranteed. The production of the DME system is aimed at satisfying the corporate objective to facilitate and promote mineral exploration and development. This paper outlines some current developments in the system.

Jan 1, 1994

In considering the architectural design of the group of buildings which make the surface workings of a mine, the variety of function of the buildings is the most outstanding feature. It falls to the architect to unify the group in a manner which still expresses the function of the individual buildings. In achieving this, many perspective studies were made at an early stage and as the area was developed, a scale model was produced initially for design study purposes and later completed as a model of the final development.

Jan 1, 1957

Computer programs for the storage, retrieval and use of basic thermodynamic and physical property data for chemical substances are described. Methods are presented for the collection, critical assessment and pre- processing of source data for files containing enthalpy, entropy and heat capacity data for 3000 compounds, enthalpy and excess entropy for 200 dilute solutions and critical propert- ies and vapour pressure for 600 compounds. Retrieval programs are discussed which allow the tabulation or plotting of many basic and derived thermodynamic properties for chemical substances or balanced reactions. Examples are given of the use of such data to infer the stability or corrosion resistance of materials and the feasibility, yield and heat release of reactions. A general purpose calculation program is discussed which allows the equilibrium compos- ition to be found for complex systems with many species and phases, using the method of Gibbs energy minimization. Methods of correction for non-ideal behaviour in these systems are discussed, as well as methods for fixing, maximizing or minimizing any desired property of the system. Examples are given of the simulation of various laboratory Experiments and industrial processes by this method.

Jan 1, 1977

During conventional eddy current separation, a repulsive force is applied to metallic particles by placing them in a rapidly changing magnetic field generated by a spinning magnetic rotor carrying an arrangement of alternate magnetic poles. This method works effectively for larger non-ferrous metallic objects, such as aluminium cans, but as the metallic particles become smaller, the bulk repulsive force on the particles is increasingly replaced by a rotational torque. Therefore, for small metallic particles it makes sense to use particle rotation, rather than particle repulsion, to effect a separation. Eddy current separators using particle rotation are similar in construction to present separators, but are designed to produce a rotating field of essentially constant angular velocity and field strength. Practical and economic particle rotation eddy current separations are possible down to particle sizes of about 200 ¦m, but separations, at probably uneconomic rates, can be carried out on particles as small as 50 ¦m.

Jan 1, 2000