Search Documents

By Happ J. V

Factors affecting the rate of arsenic removal from lead bullion during softening processes were studied. Very high rates of removal could be obtained under conditions of intense agitation and ready availability of oxidant. Reaction mechanisms were proposed to explain the sequences observed. Selective removal of arsenic with minimal loss of antimony from bullion was favoured by a low temperature Harris process and oxidizing via a caustic soda medium.

Jan 1, 1987

By Mur D. M

Metal ferrites are formed by the high temperature reaction of various metal oxides with hematite and are commonly found in the calcines derived from the sulfation roasting of zinc, copper and nickel sulfide concentrates. The Jarosite Process is designed to treat such zinc ferrites by hot acid dissolution but little information is available on the basic reactivity of various ferrites and the effect of Eh. As part of an overall study of the reactivity of calcine products from copper and nickel sulfide concentrates it has been found that Eh plays an important role in the rate of dissolution of magnetite, hematite and nickel oxide by HC1 and H2SO4. Further studies on the reactivity of pure synthetic copper,zinc,and nickel ferrites also show a dependence on Eh. This paper discusses the relative reactivity of iron oxides and metal ferrites in 1 M HC1 and the results of electrochemical studies using cyclic voltammetry. A mechanism for the dissolution reaction is proposed as well as factors which determine their leaching. It is shown that the rate of leaching of metal ferrites with HC1 is enhanced in the presence of reducing agents such as Cu(I) and Sn(II). By contrast the leaching of NiO is enhanced by oxidising agents such as Cu(II).

Jan 1, 1987

A new experimental procedure for determining the solids flux curve is detailed. The procedure is based on measuring the concentration at various heights of a bed of settled solids formed during a semi-continuous sedimentation test. Unlike conventional thickener area calculations, the test procedure demonstrates the dependence of the flux curve on the system feed flux. At a given feed flux, there was good agreement between the solids flux curve determined by the method and continuous sedimentation results. The widely used method of Kynch was found to be restricted to relatively high effective feed fluxes and consequently there was poor agreement with continuous tests at low feed fluxes. The flux curve determined by the method of Coe and Clevenger was invalid for all feed fluxes. A case study shows how the required thickener area would vary for a number of fine coal processing options.

Jan 1, 1989

Sampling criteria and practical implementation of these criteria are discussed with a view of achieving and maintaining a high level of quality for minerals at their various stages of production through to their utilisation. From this it will be shown the advantages that can be gained by producers who undertake stringent quality control programmes for their ores, thus ensuring they have a competitive edge over other producers.

Jan 1, 1985

Reconciliation of the ore reserve has been an integral part of mine planning since Bougainville Copper Ltd. commenced mining operations at Panguna in 1972. Confidence in the ore reserve is considered essential, both for long term planning of the deposit, and for fair and accurate reporting of the mining resource to shareholders. Recoverable, proven reserves are published annually. Although the ore reserve quoted is based only on diamond drill hole (DDH) information on a 122 metre by 122 metre grid, predictions are regularly reviewed against production. Concentrator results are taken to be the best estimate of grade and tonnage. Surveyed mined perimeters and average blasthole grades are reconciled at the end of each month against the concentrator figures. Predictions of the in-pit reserve are made using an orebody model. DDH and blasthole (BH) sample grades are used to make predictions for both long and short term planning. This paper describes how reconciliations are used to validate ore reserves at Panguna. Development of the orebody model is described, and some of the difficulties encountered in doing reconciliations are addressed.

Jan 1, 1987

The, Ore-bodies.-The ore-bodies of the North mine, North Broken Hill Ltd.; consist of two lenses, connected by a narrow neck of mineralized country. They pitch at an angle of 40° in an easterly direction and dip north at 60° to the horizontal. The southern ore-body, on a horizontal plane, has a total maximum length of 800 feet and in one place attains a width of 230 feet, whilst the northern orebody has a maximum'length of 600 feet and a maximum width of 80 feet.

Jan 1, 1940

By Hodges D. A

The manufacture of steel from raw materials which have to be mined, transported and processed must affect the environment. Steelmaking, like almost every other stage of manufacture involves the unwanted production of dust and fume; thus a major part of the steel industry's effort to minimize changes to the environment is the collection, treatment and recycling of dust and fume to avoid pollution of the atmosphere and waterways. The paper describes how this achieved in the various steelmaking processes and shows the diversity of problems-and their solutions in this context. Particular emphasis is, given to basic oxygen steelmaking.

Jan 1, 1976

The Myally Beds, Surprise Creek Beds and Mount Isa Group form the upper part of the Proterozoic Western succession of rocks in northwest Queensland. The latter two units are partly equivalent, and are important for their base metal content at Mount Isa and elsewhere. The arenaceous Myally Beds lie unconform- ably or disconformably below the Mount Isa Group and Surprise Creek Beds; they contain four mappable units which were deposited on a broad, shallow shelf washed by east-trending currents. Emergence of the Myally shelf initiated a series of parallel, possibly intra- cratonic, troughs to the east and west. In the east, the Surprise Creek Beds were deposited between the emergent shelf and base- ment rocks, and consist of a shelf and trough facies divisible into 7 and 10 units, respectively. Trough sediments are continuous north-south, and show turbidite character- istics; algal dolomite characterizes the shelf facies. To the west in the Mount Isa trough, an orthoquartzite facies, the Warrina Park Quartzite, defines the base of the Mount Isa Group. Hinge zones between the shelf and trough environments are marked by east-west facies changes, and provide a focus for later major north-south faulting. However, some penecon- temporaneous faulting near Mount Isa is best explained as complex post-depositional faulting of a disconformable sequence. Subsidence and deposition in the Mount Isa trough continued for a longer period than in the Surprise Creek trough, allowing accumulation of lead and zinc deposits in the upper half of the sequence. The Surprise Creek Beds appear equivalent to the lower half of the Mount Isa Group, and are probably not prospective for lead and zinc. Turquoise and possible other secondary copper minerals are widespread in the Warrina Park Quartzite and equivalents in the Surprise Creek Beds, and further investigation of these formations seems warranted.

Jan 1, 1974

Effective pre-splitting is a key feature of wall control blasting. Most mining operations use historical designs or rules-of-thumb for designing pre-split blasts. If productivity and safety benefits are to be gained, these methods need to be improved in order to accurately predict pre-split performance. This will become more pertinent as overburden depths increase, placing more demands on the pre-split operation. A classical qualitative quasi-static description of pre-splitting (Kutter and Fairhurst, 1968) is presented and it is shown to give some useful insights into the pre-splitting process. In particular, it is clear that the time interval between the initiation of adjacent pre-split holes is a very important factor. In terms of this analysis, it is shown that current techniques which employ detonating cord as the surface initiation system are not optimal. A static quantitative model for pre-split design which has been widely reported is then discussed and its simplifying assumptions and their implications are examined. It is shown that several of the assumptions may be reasonably justified in the light of real pre-split results. It is concluded that the model should yield conservative designs. For this model, the key calculation of the blasthole pressure that is needed to determine the required explosive charge is highlighted. Popular methods employed in the literature for describing the expansion of real detonation products are shown to be inappropriate and an alternative method using the non-ideal detonation code, CPeX, is proposed.

Jan 1, 1995

Over a four year period from 1984 to 1987, a broad range of ground conditions were experienced in recovering old workings at the Walhalla mine in central-eastern Victoria. Access to the ore zone was gained via old workings and new development. The work included: Recovery of vertical and inclined shafts. Recovery of collapsed winzes. Recovery of level drives and crosscuts. Spiling through broken ground and old mullock. Pre-grouting of caved zones. New development using small-scale rail equipment and "bobcat" Loaders.

Jan 1, 1988

There are many factors influencing the way in which a mining company disposes of tailings. Some of the more important factors include physical and chemical properties of tailings, cost, availability of dam wall construction materials, type of mining operation, topography and environmental constraints. As a result, the mining industry has seen a diverse and innovative range of disposal methods developed to satisfy the many conditions imposed at tailings disposal sites. This paper discusses a range of tailings disposal methods currently practiced in the mining industries in North America. These methods include various inpit disposal techniques, upstream, downstream and centreline dam construction and zoned earthfill or rockfill embankment construction. The thickened tailings disposal method and the disposal of fine clays are discussed. The importance of improving the depositional properties of tailings to enhance storage capacity, water reclaim, dam wall stability and final reclamation is stressed. It is important that mining companies are made aware of the full range of disposal methods and dam construction techniques available today. Such an awareness will help improve the planning, design and construction of safer and more efficient tailings disposal facilities in the future.

Jan 1, 1989

In the 100 years since the formation of The Australasian Institute of Mining and Metallurgy there have been significant changes in all aspects of the mining industry.A number of the changes have been driven by technical evolution or necessity, others have been driven by developments in the application of the products produced from the mining of minerals. Other changes have been driven by shifts in community values.

Jan 1, 1993

By Shining Z

The strength and deformation of more than two hundred coal samples have been tested in the condition of triaxial compression. The regression equation showing the relationship between coal strength and pressure in the pores, as well as confining pressure, was obtained. The appropriate calculation for stress-strain curve was carried out. Further, an analysis shows the variation of coal strength and its modulus of elasticity in methane medium.

Jan 1, 1992

The economics of gold differs from that for base metals mainly because a large component of gold demand is investment or stock demand whereby the metal is purchased and stored for monetary or anxiety motives rather than fabricated into industrial products.The second major component of gold demand is fabrication, principally into jewellery but also, to some extent, into industrial products.Supply to the Western private- gold market comprises non-Communist mine production, Communist sales (chiefly from the USSR), and, finally, net sales by the Western Central Banks, which have total stocks of about 35,000 tonnes and which are sometimes net buyers as well as sellers.The different components of demand and supply fluctuate from year to year.

Jan 1, 1984

By Martins V, Dunne R

A re-evaluation of the Hampton Boulder prospect in the early eighties resulted in a decision to proceed with mine development in December 1985. A 500 000 tpa gold treatment plant was commissioned in December 1986. The treatment facility was expanded to 1 600 000 tpa in July 1988. A tailings treatment plant to improve recoveries from harder gold bearing sulphide ores was built in December 1990. The development of an underground mine in 1991 meant that a source of sand for backfill was required. A sands plant to fulfil this requirement was commissioned during November 1991.As of June 1992 a total of 7 710 487 tonnes of ore have been treated through the New Celebration gold plant. Total gold production from inception of the new mine until June 1992 is 545 470 ounces obtained at an average recovery of 90.1 per cent from an average gold head grade of 2.4 g/t. The combined quoted ore reserves at the end of December 1991 was 14Mt grading 1.8 g/t gold

Jan 1, 1992

Cerro Matoso (CMSA) in Colombia produces ferro-nickel from lateritic ore containing approximately three per cent nickel, using a Rotary Kiln - Electric Furnace (RKEF) process, in which the calcining of the mineral within the kiln is second in importance only to the smelting of the mineral in the Electrical Furnace. This article discusses the installation and operation of an expert system to control the kiln of CMSA. In the CMSA process, the run-of-mine ore is crushed, homogenised, dried and mixed with a small percentage of coal, before being heated up to 900¦C in a rotary kiln in the presence of natural gas mixed with air in a controlled proportion (air/gas constant ratio). The final objectives of the process are the following: ò To reduce to a minimum the iron and nickel oxides in order to convert these into metallic ions; this is a reduction process to facilitate largely the smelting in the electric furnace. Since the reduction is made with natural gas, it is much more economical than the subsequent complete reduction in the electric furnace, since electrical energy is much more expensive by unit of processed mineral. ò To heat the mineral as much as possible to facilitate the subsequent smelting. ò To eliminate totally the moisture content of the ore. An expert system with fuzzy logic was commissioned in 1994 for the control of the kiln and it has operated with good results ever since.

Jan 1, 1996

By Lumley G. I, Hayes H

Non-intrusive methods for the reliable determination of dragline bucket and rigging performance have been achieved using physical modelling. Modelling offers a logical first step towards developing mathematical simulation models. The process of physical modelling has been applied successfully to predict dragline bucket performance and capacity as well as to demonstrate the effect of varying dump rope length on performance. ACIRL's Surface Miming Group has used physical modelling to carry out dragline bucket sizing for a new high productivity bucket and compared performance with Throng Coal's existing dragline bucket. The predicted bucket performance has since been confirmed in the field using dragline monitoring techniques.

Jan 1, 1992

The accuracy of an ore reserve is only as good as the geologist's understanding of the deposit. The methods that are applied to resource and reserve estimation reflect that understanding. At the Olympic Dam copper-uranium-gold deposit in South Australia, evolution in the understanding of the controls on mineralisation coupled with the changing demands of the project have led to changes in the approach to reserve estimation. The project has moved into a phase where detailed stope mining reserves are now required as distinct from global ore reserves. The complex nature of the mineralisation and the large amount of data demand that all available information be readily accessible in a flexible format. To enable the selective manipulation of geological and assay information and its characterisation, a relational database has been developed. For reserve calculations themselves, initial computations were based on a system derived from that used for the Kambalda nickel orebodies. The Olympic Dam system differed mainly in the use of statistical analyses in the estimation of grade instead of the previous polygonal area of influence weighting method, Three dimensional weighting techniques are now being used for local reserve estimates. Flexible facilities for raw data handling combined with grade estimation techniques which are commensurate with the mine geologist's understanding, produce detailed gridded and contoured ore zone models suitable for reserve calculations and stope designs.

Jan 1, 1987

Development of a New Dry Density Separator for Fine-Grained Materials

Sep 13, 2010

By Anderson KG

Multi-seam mining under the western portion of Lake Macquarie NSW commenced in 1982. Up to three seams separated by partings ranging from 10 to 30 metres are mined simultaneously by Newcom Collieries. A feature of these workings is the minimal bedrock cover, which ranges from 130 metres down to only 40 metres. "Surface" subsidence control has an over-riding influence on the design of the workings. Subsidence considerations govern both the selection of the mining method and the dimensioning of the workings. To date, workings have been designed in accordance with the "Wardell Guidelines for Mining Under Tidal Waters". These guidelines are tabulated and evaluated in the light of advances in rock mechanics knowledge and local subsidence data collected since the Guidelines were formulated in 1974. The local and regional stability of shallow workings designed according to the Guidelines is evaluated.

Jan 1, 1986