Search Documents

By Watt KL

Chemical anchors for use in rock bolting have been produced in Australia under licence for several years. These anchors are alternatives to the more normally used mechanical anchors and give improved anchorage strengths under some conditions, although at greater cost. Considerable development during this time has resulted in an improved sausage-type chemical anchor more competitive in price, to such an extent that its use is increasing markedly. Particular-improvements allow load application up to the strength of the bolt within 2 min, reduction in cost, self-extinguishing features in the resin, improvements in manufacturing techniques, and an improved water- insensitive casing. At the same time, smaller bolt sizes have allowed reduction in resin volumes with consequent cost reduction. At this stage several aspects remain to be improved, particularly specialty anchors for specific purposes and Packaging.

Jan 1, 1971

By B Madeja-Struminska

The method of evaluation of the approximate temperature of arising spontaneous fire centre and time of coal self-ignition is presented in this paper. The method uses BystronÆs (1997) model of coal self-heating and measurement of carbon monoxide concentration in the mine air outside the fire centre. Knowledge of the spontaneous fire centre temperature and time of fire beginning allows for more accurate analysis of the fire hazard in the coal mine and allows for adequate time to undertake special fire prevention actions. The method is illustrated by an example from Polish mining practice.

Jan 1, 2005

The Granites Gold Mine has far exceeded the design capacity of 300,000 tonne per annum during its first sixteen months of operation. The presence of considerable free coarse gold has made it imperative that the gravity section operate at maximum efficiency. The inadequacy of acid digest- ing facilities and trying climatic conditions prompted management to initi- ate investigations into the use of Intensive Cyanidation as an alternative method for upgrading gravity concentrates prior to smelting.

Jan 1, 1988

By B D. Sowerby, N G. Cutmore

Improved process control can be achieved through the accurate and reliable on-line measurement of critical process parameters in real time. Over the past few decades on-line analysis techniques have been developed and applied in the mineral and energy industries for the measurement of process stream composition, mineralogy, particle size and flow rates. This has led to increased throughput and product quality while reducing processing costs and minimising emissions. The support of a sustainable mineral processing industry will require the further development of on-line analysis and control technologies. The application of developments in instrumentation combined with improved control strategies will lead to improvements in process efficiency resulting in large economic benefits to the industry, reduced energy usage and lower process emissions. There is a clear convergence of interests in being able to better measure and control minerals processing in terms of the triple bottom line of economic, social and environmental impacts. Technology is increasingly becoming available enabling measurement across the entire spectrum of minerals processing from mining to hydrometallurgy and pyrometallurgy. CSIRO is developing a range of these new technologies. A number of these developments are discussed in the present paper, namely: on-line particle size analysis and acoustic emission methods to enhance the control and optimisation of grinding circuits; on-line mineralogy of dry powders and slurries; on-line bulk elemental analysers for application on conveyor belts and in smelters; and the development of new sensing technologies for sorting base metal ores.

Jan 1, 2002

This paper discusses considerations to be made for the selection of rock tunnelling machines, as opposed to drilling and blasting. A systematic approach is presented in terms of utilizing data frcm site investigations to accurately forecast machine performance for estimating and planning purposes and to help minimise associated risks. Useful rock index properties are identified, and correlations for predicting advance rates for roadheader and full face machines are presented together with a simple method of characteristing rock mass conditions for estimating machine utilization and the savings to be gained in support costs. Finally considerations for tunnelling in adverse ground, for advance probing and for large sized tunnels are outlined.

Jan 1, 1987

New Zealand Steel Limited is nearing completion of the environmental reporting and planning procedures for its proposed fivefold expansion to steelmaking at Glenbrook, and supporting mining operations at Waikato North Head. A report on the proposal to transport concentrate from the mining operations to Glenbrook has also been prepared and is awaiting release. This paper draws from these events, and by discussing some of the problems encountered, gives some guidelines for the preparation of an Environmental Impact Report.

Jan 1, 1981

By Clark IH

Numerical modelling is an effective aid for the planning and design of underground coal mines. With funding from the National Energy Research Development and Demonstration Program, CSIRO Division of Geomechanics has produced a workstation environment which will allow the Australian Coal Mining Industry access to a wide range of numerical design models. The emphasis is on usability and simplicity and the long-term aim is that the techniques should be used routinely at the mine site, so that, in the future, design of a new underground mine will routinely involve modelling of each proposed layout.Each of the five numerical analysis programs, FESOFt, FLAC, MNLAY, FEBLK and UDEC has both strengths and weaknesses. Some analyses with each program demonstrate areas when; observed in situ behaviour in underground coal mines has been successfully modelled, and the results of site monitoring provide a basis for comparison with the predictions of numerical models.

Jan 1, 1991

By P Hartlieb, M Noeger, M Varelija

Rock bolts are important in underground mining as they provide support to the rock mass around the excavation. They are the most common reinforcement method in mining and civil engineering excavations. The length of the bolts, types and spacing between them can be varied, depending on the reinforcement requirements and the use case (Kolapo, Onifade and Praise, 2022). The rock bolt provides safety and stability for the rock mass in the excavation area and they can be mechanically anchored, grouted, or friction anchored. They normally don’t have a measurement option and there is a possibility that it failed without showing visible signs on the surface, especially in grouted rebar bolts where they can still have some residual strength. Therefore, support functionality can be lost without recognising it. To overcome that, sensors can be installed on all three previously mentioned bolt systems. Intelligent bolts with implemented measuring systems have a function of showing changes and indicating if there is some damage on the bolt. So, it can be said that intelligent rock bolts are regular bolts equipped with additional instruments which are helping us detect potential instabilities inside of the rock mass or malfunction of the bolt itself. Changes in rock mass can be tracked, by measuring rock bolt reaction concerning the excavation response. Rock mass damage and instabilities are therefore measured in terms of rock mass deformation. Moreover, other additional information depending on the type of the sensor device could be collected. Based on such measurements, information about rock mass state can be derived. Different rock bolt types work at different reaction principles. Therefore, limitations on sensor application and information that can be extracted must be considered.

Sep 1, 2024

This paper reports on the field results of using electronic detonators to improve blast outcomes. OricaÆs electronic detonator, the i-konTM Digital Energy Control System, allows exact and precise timing in 1 ms increments from 0 to 15 000 ms. This gives the blast engineer and shotfirer the ability to fire a blast using any possible desired sequence. In the three years that have followed the release of the i-konTM System, Orica has been re-exploring ways of initiating blasts using the abilities of electronic detonators to improve fragmentation, diggability and crusher throughput. This study began with revisiting fundamental blast theory, lead to generation of new state of the art computer fragmentation modelling and ended with many iterative field trials of i-konTM blasts across a wide selection of mining methods and rock types. At three sites a detailed measurement process was undertaken to compare the results of pyrotechnic blasts with i-konTM blasts. This paper will detail the significant improvements in fragmentation, diggability and crusher throughput that was found at these sites.

Jan 1, 2003

Methods of measuring the frictional properties of rock surfaces, both by direct sliding and in triaxial apparatus, are described. It was found that for some rocks the coefficient of friction remains reasonably constant as sliding is continued but for others it increases considerably.The effect of fluid pressure in the surface of sliding was found in all cases to be adequately represented by the effective stress criterion. Some observations on sliding on two conjugate planes showed that the motion on the two planes may be very different, depending on small differences in the constraints.The coefficients of friction of natural open joints in bore core were found to lie in the comparatively narrow range 0.32 to O.68 although surface coatings were very diverse.A set of diagrams on the equal area projection is given which enables a rapid determination to be made of those planes on which sliding is possible in a given three-dimensional stress field. The influence of the intermediate principal stress on this is of considerable importance.

Jan 1, 1969

Coal mining in the Illawarra commenced in 1848. By the early twentieth century mining operations were spread over quite a distance along the coast centred on Wollongong. By this time there were already numerous tunnel mines and one shaft mine. Coal was first reported in Illawarra by Lieutenant Flinders on a voyage of exploration, southerly along the coast from Sydney in 1796. Because of the topography, particularly the escarpment and the narrowness of the coastal plain, access from Sydney was not easy by land and the normal access was by sea. It was not until some coastal areas had been developed for agricultural purposes that the mining of the seams on the South Coast commenced for the supp- ly of fuel. The most important mines in the early nineteenth century were Bulli and Osborne Wallsend. In general, coal was won from the tunnel mines and was transported directly, usually by tramway, to the nearest shipping point. Considerable hardship attended the earliest attempts at mining coal in regard to materials for mining and the way of life of the miners in the vicinity of the mines. With the growth of production and the installation of coke ovens at some mines the area, hitherto virgin bush- land, began to take on a more industrialised appearance. The mines were necessarily small,

Jan 1, 1976

By Szpindler G

The results of pot-furnace tests with 35 bituminous coals from 20 seams in New South Wales and Queensland were used to establish the relationship between coal properties, as determined by standard laboratory tests, and the combustion process. The rate of combustion is influenced chiefly by the expansion of the fuel bed, but this cannot be accurately predicted from the crucible swelling number of the coal.The effects of various other factors, such as calorific value and ash yield, were investigated and statistical analysis of the results shows that the coals could be classified satisfactorily according to two experimentally derived parameters, namely heat-release rate at an air flow rate of 260 lb/sq.ft/hr and air flow rate giving stoichiometric combustion. The grouping obtained is shown to be related to ash yield and swelling number.INTRODUCTIQNThe rate of heat release from the fuel bed of a travelling grate stoker and the efficiency with which the heat is used depend upon the design and method of operation of the furnace as well as upon the properties of the fuel. It is difficult to draw general conclusions concerning the influence of fuel properties from tests on a single stoker installation. In the pot-furnace test, on the other hand, a part of the same combustion process as occurs on a travelling grate is carried out in isolation, uninfluenced by furnace design variables, and consequently the effects of coal properties and of the method of pretreatment can readily be demonstrated.While the combustion pot provides a rapid method of assessing the combustion characteristics of a fuel during the ignition and burn-out stages under standard conditions, and of predicting changes in performance with changes in fuel or in air flow rate, it is unable to simulate certain features of furnace design and operation. Data from combustion pot...

Jan 1, 1962

SINCE writing the above-mentioned paper, some further indicator cards have been taken from the No. 1 machine, and the writers believe that a reproduction of these cards will be interesting as illustrating the performance of the machine after fifteen month steady running, night and day, seven days per week and twenty-four hours per day, at the average speed of fifty-seven revolutions per minute (see Fig. 1, page 60). For the past twelve months no adjustment have been made in the valve setting, and the only repairs have been in connection with the springs of the poppet valves, and these but slight, the springs latterly having been removed. The cards illustrated were taken with one indicator, and, therefore, are not simultaneous, andmay show to some extent the yariations of individual strokes, and with that qualification may be taken as typical of the machine's average performance.In connection with some feed-water measurements of the winding engines a rough test was run with the two compressors, the Riedler and the Corliss, coupled to the condenser, and running at fifteen and fifty-seven revolutions per minute respectively, with the result of 15.9 pounds of steam per indicated horse power per hour. This result, though only approximate, seems to indicate that the No. 1 machine is running under the guaranteed consumption, and that it is capable of maintaining this under the severe conditions of everyday practice.

Jan 1, 1909

By D Kent, J Kirkpatrick

The mining industry has long wanted a single communication back bone to cover the majority of their requirements underground. The convergence of communication technologies in the office/surface environment has been identified by the mining industry as a means to achieve their long-standing goal. In particular use of Internet Protocol (IP) systems are seen as proving a basis for a mineÆs communication infrastructure. This paper presents the development philosophy and work undertaken by Inco Limited in Canada, as well as the implications of this on suppliers to enable the technology to be mine worthy and readily available.

Jan 1, 2005

By i, A Shirbazo, S Saydam, S Ata, H L. Ram, B Li

The integration of internet technology into industrial sectors has significantly accelerated the adoption of Internet of Things (IoT) devices, transforming communication, data aggregation, and information distribution. The mining industry has embraced this evolution by deploying IoT devices and advanced technologies like autonomous robots and sensors to enhance operational safety. These sensors enable real-time data transmission and continuous monitoring of key parameters, providing decision-makers with timely insights. However, the interconnected nature of these devices has introduced complexities, resulting in inconsistencies across operations. Addressing these challenges, this research explores the application of modern digital principles to the mining industry through the Reference Architecture Model Industry 4.0 (RAMI 4.0). RAMI 4.0 offers a robust framework that integrates digital and physical systems, promoting data transparency, interoperability, and decentralised decision-making. This study aims to briefly introduced framework designed for the unique challenges of mining operations, leveraging the latest digital technologies. The lack of standardisation in the mining sector highlights the need for a comprehensive approach to tackle issues such as interoperability, scalability, security, safety, and repeatability. Establishing standard procedures can ensure smooth interaction between connected devices, ultimately enhancing operational efficiency in the growing IoT ecosystem within the mining industry. Introducing a well-defined reference architecture like RAMI 4.0 can streamline management processes and improve operational efficiency in mining. By adopting this framework, the mining industry can effectively navigate the challenges of digital transformation, leading to a more connected and resilient future. The study concludes that RAMI 4.0, with its structured approach, can significantly enhance the efficiency and productivity of mineral processing operations, fostering sustainable growth in a digitally driven industrial landscape.

Sep 1, 2024

By N Tuffs, R Peace, S Xue

Mine gas control is a major issue in most of the gassy underground coal mines, due to its direct impact on safety, production delays and cost of production. Analysis of the gas data, from different collieries in Australia showed that longwall gas emissions have increased substantially over the years. Simply increasing the number of goaf holes in the panel or decreasing goaf hole spacing seems not to be effective, in controlling high goaf gas emissions. A major research project has been undertaken by CSIRO in collaboration with mine sites to address this goaf gas control issue with the aim of developing effective and optimum goaf gas drainage strategies. The project has combined extensive field studies with computational fluid dynamics (CFD) models, to characterise goaf gas flow patterns and develop effective gas control strategies. The research work specifically involved review of gas control issues at field sites, goaf gas monitoring, tracer gas tests, CFD simulations and extensive field trials. Field demonstration studies of the new optimum strategies have been conducted at two collieries in Australia. The project results have shown that the optimum strategies were highly successful, in improving the overall efficiency of goaf gas drainage systems, at both the field sites. Results of the goaf gas flow characterisation studies and field demonstration studies are summarised in this paper.

Jan 1, 2005

Magnetic Separators have a wide application in dry separation processes, frequently in conjunction with High Tension Separation. Dry processes can frequently be superior to established processes in more commonplace mineral associations. A system of dynamics is postulated and the forces operating ar'e examined, together with a method of evaluating the effect of operating variables. Practical applications of these theories to obtain optimum results on an individual separator, and various separations using a laboratoryroll type separator are described.Practical Flowsheets are of two main types, the first consisting of a series of scalping operations, the second for rougher, cleaner, and scavenger operations with middling recirculation. Some common separation problems with certain mineral associations illustrate the need for different approaches for different mineral associations. A table of mineral separation characteristics is appended, from which amenability may be tentatively estimated.INTRODUCTIONMagnetic separators are widely used, either alone or in conjunction with other wet and dry concentration devices, for the upgrading of a variety of minerals. The high standards of efficiency attainable in dry mills, together with reduced operating and labour costs, are slowly becoming apparent in a wide variety of plants. The combination of wet and dry concentration plant familiar in beach sand mining is finding application for such processes as upgrading a crushed chromite product, and production of clean scheelite,cassiterite, and other concentrates. Other dry beneficiation processes (such as the high tension beneficiation of iron ore, and the benefiGiation of asbestos) avoid the use of wet processes completely.Dry separation processes are likely to be applied more widely as their possibilities become more generally known.

Jan 1, 1958

A nuclear technique utilising the gamma-ray resonance scattering process is used at Isa Mine for the determination of copper in drill core and bulk mineral samples. The Copper Bulk Analyser (CBA) provides quick and accurate non-destructive copper analysis of drill core at costs two to three times cheaper than conventional chemical techniques.The almost immediate availability of sample results enhances the efficiency of the mine geologist in the duties of grade control, design of diamond drilling programmes, and input to planning. The unit has proven to be a reliable and accurate production tool requiring a minimum of technical support.

Jan 1, 1990

In 1985 a 2.5-tonne top blown rotary converter was installed in the silver refinery at Cominco's Trail Operation to carry out the final cupellation of burndown metal to Dore metal. The furnace is fired with an oxygen-natural gas lance which is capable of achieving a variety of furnace conditions, varying from reducing to highly oxidizing. Reaction rates are about 4 times greater than using conventional cupel furnaces. The faster reaction rates improve productivity and reduce in-process precious metal tie-up. The furnace is also used to reduce litharge slag for bismuth recovery.

Jan 1, 1989

This is the second of a series of papers dealing with Geology in Exploration. The first, published by the Australasian Institute of Mining and Metallurgy, Proceedings Nos. 143-144, 1946, was written as an introduction to the subject and employed the exploration geology of the Cobar field to illustrate the prospect thinking. This paper will be concerned with the problem of ore repetition in depth and borrow its- example from the Mount Lyell copper field. The writing will be taken up altogether by the example. Nevertheless the intention remains to develop the subject in terms of its wide interest and application.The Mount Lyell field possesses large actual and prospective resources within, and in the vicinity of, the known deposits. This paper does not bear at all on these accessible ore reserves and tangible prospects. There is also in this area evidence of deep ore. The possibility is of little practical interest at present. But the picture of ore repetition, exemplified by the Mount Lyell field, does matter now to the outlook on exploration in this country. For once this essential feature of ore occurrence is widely understood there may develop, on the scale warranted, the search for major deposits which do not outcrop but which are still at shallow depths because of the part erosion plays in this story of concealment and exposure of ore. Also there is the chance in some fields (including Mount Lyell) of a second harvest of orebodies within mineable depths. This exploration goal, introduced in the first paper, will appear more clearly as the Geology in Exploration series is written up. Here the concern is to show the character of the geological evidence which points to the occurrence and recurrence of ore in the earth's crust, the picture at the foundation of this exploration scheme. There is considerable information in the Mount Lyell area of the structures...

Jan 1, 1947