Search Documents

By Ellis WK, Greenwood-Smith R

A nuclear technique for the analysis of copper in bulk materials has been developed and successfully field tested at Mount Isa Mines Limited. The technique utilises the gamma-ray resonance scattering process. A bulk analyser based on this technique gives a rapid and accurate measurement of the percentage by weight of copper or nickel aver- aged over a large mass of sample, typically 20 kg. The only sample preparation required for accurate analysis is crushing to -2.5 cm. At Mount Isa over 100 mineral samples covering a wide range of rock types and copper contents were analysed. Bulk analyser assays and chemical laboratory assays agreed closely for underground pillar-extraction and geolog- ical chip samples, conveyor belt samples, and finely ground samples from the ore concentrator. For the concentrator samples, the root mean square deviation between bulk analyser and chem- ical laboratory assays was 0.06 wt.% copper. The chemical assay errors for these samples were about 0.06 wt.%

Jan 1, 1975

By Wilson PH

A research programme sponsored through the Australian Mineral Industries Research Association investigated two aspects of mine aerodynamics on model scale. These were aero- dynamic losses in (a) shaft/airway intersections and (b) losses created by mine cages moving in a combined haulage/ventilation shaft. The shaft/airway intersections studied included base and intermediate levels for both upcast and downcast. shafts, with one to four rectangular airways intersecting a circular shaft. Changes in intersection geometry were limited to the installation of 45¦ conical brow cutoffs of varying size and the addition of simple flow control devices. The relative air- flows between the airways and the downstream shaft were varied over a range employed in Australian mining practice. In general, experiments revealed that a small brow cutoff was significantly better than none at all, and a simple device such as a cone can reduce losses and improve flow stability at an intersection. The mine cage studies determined the effect on aerodynamic loss of cage area blockage, height/length ratio, openings in cage walls and surface roughness due to external structural members. The results show that in a combined haul- age/ventilation shaft, when the relative air

Jan 1, 1978

By A G. L Pratt, G F. Dunstan, A Leonforte

The selection of the material sizing and mine dewatering systems are important elements in the development of a large-scale, high tonnage (greater than 4 Mt/a) underground hard rock mine. The sizing system will influence the size and type of the ore haulage system and therefore how the underground project is developed. With more underground developments considering or implementing caving methods of mining, the selection of the material sizing systems is also influenced by the caving fragmentation. Traditionally, crusher systems are used for material sizing in large hard rock mines, with the crusher installation and its ancillary equipment representing a substantial capital investment. Underground cave mining type operations generally express themselves with large surface subsidence areas, which can lead to large inflows of water from major rain events or purging underground aquifer systems. To minimise disruption to mine production, the dewatering system needs to be sized, with consideration to both storage and pumping capacities. The balance between storage and pumping capacity is assessed to provide the optimal economic solution with the appropriate risk measures. This paper outlines a process for the selection of material sizing and dewatering systems for large-scale caving operations. This process is illustrated with information drawn from NewcrestÆs Ridgeway Deeps Block Cave project. The Ridgeway Deeps Block Cave is located directly beneath the existing Ridgeway Sublevel Cave Mine.

Jan 1, 2008

By C Woodfull, S Munroe

Geological uncertainty is reduced by improved understanding of the relationship between regional-scale geological basement features (structure, composition, depth) and known local structural risk (such as recognised structural hazards at the mine). Coal mining and exploration entities can be more efficient and effective in managing geological risk at a range of scales. A more efficient and effective performance in forward interpreting and managing geological risk will result in a more efficient and effective exploration and also incremental or even significant mining cost improvements. In order to improve the understanding of basement features, a new 4D regional structural/basin framework for the Sydney Basin and the eastern part of the Gunnedah Basin has been constructed to provide primarily coal exploration and mining with a more integrated geological framework for ongoing subregional to mine-scale geological risk based studies. The model has been developed from a range of available regional geophysical and geological datasets, of variable detail and reliability, which have been brought together to generate a more robust structural and tectonic model than could be generated with any one single dataset. An initial regional structural model for the Sydney Basin was constructed in 2003 and an update to the model was released in 2005 (SRK Consulting, 2003; 2005). The development and ongoing refinement of the model was undertaken with financial and data support from a number of coal mining industry, gas exploration and government organisations. Prior to, and following the development of the regional structural/basin model and associated Information Base, a number of more area-specific studies have been completed, using the æbasement upÆ assessment approach. The methodology for developing comprehensive structural models, from the basement up, is outlined. The approach can be applied at a country-wide, regional or lease area scale. Case examples of where this approach has been used as an effective and efficient method in improving geological certainty and as a predictive tool to help manage geological risk are also presented.

Jan 1, 2006

By Tucker A. J

An overburden blast utilising horizontal blast holes was successfully attempted at the Ulan Coal Mines during December 1991. The blast reduced operational problems and costs and improved dragline productivity in an area of that contains poorly consolidated sands and clays overlying very hard Permian strata.The fan shaped shot consisted of seven 250 mm diameter holes between 80 and 95 metres long drilled into the highwall face. The holes were loaded with ICI Powergel Gold 25606 bulk Emulsion explosive. The design powder factor was 0.15 kg/bcm for the total shot of 180 000 bcros and 0.44 kg/bcm for the competent Permian strata into which the holes were drilled. Fragmentation from the horizontal blast was comparable to areas conventual blasted. Following the success of this shot further shots are planned for this area.

Jan 1, 1992

Amongst the Pacific Rim countries, Papua New Guinea (PNG) is the leader in new gold discoveries and developments leading to new production. PNG has shown a dramatic increase in gold production when taken from a base of about 600 000 ounces in 1984 to 1 160 000 ounces in 1986. 1987 is expected to produce about 1 500 000 ounces and new planned developments will give further large increases. PNG's leading position when compared with neighboring Pacific Rim countries is only partly due to its favorable geological setting along the "Rim of Fire" epithermal zone. More important have been well-thought-out mining development legislation and good administration as well as consistent taxation and royalty policies. A stable political environment and a track record of new mining developments over the last 15 years, both pre and post Independence in 1975, have also been important factors in encouraging the new developments. Early Portuguese explorers associated the New Guinea mainland with gold as early as 1525 but it was not un,11 1R77 that a small ill-fated gold rush gave the first recorded production at Laloki near Port Moresby. Modest but commercial discoveries were made in the outer islands and coastal mainland regions from 1888 to 1926. In 1922 William "Sharkeye" Park found gold at Edie Creek and this led to major discoveries at Wau and Bulolo which were the first large scale commercial gold Operations.

Jan 1, 1987

By Cresswell G. M

The international coal industry is becoming increasingly aware of the economic impact of coal dewatering in terms of plant yield limitations, attainment of product specifications and freight costs. This paper examines the current position of dewatering within coal process plant design and reviews equipment developments over the past decade.

Jan 1, 1993

The current drill-and-blast method of tunnelling is cyclic and, for this reason above all others, has a future application potential which is lower than that of continuous methods. There is scope for progress in several facets of today's drill-and-blast tunnelling. But even if each of its unit operations and the synthesis of these were to be optimised, this conventional method will, in the long term, fail to be a serious competitor for tunnelboring machines (TBMs), roadheaders and the like. If its role in tunnelling is not to decline at an increasing rate, drill-and-blast will need to be transformed into a continuous system. Boring and cutting machines consume considerable energy (and expenditure) in creating rock fragments which are smaller than those required by muck-handling equipment. In this respect, blasting is more efficient. Mechanical methods are also less versatile and flexible and, when planning proceeds on a basis of meagre or inadequate geological data, cannot be costed as accurately. Currently, research gains for TBMs and roadheaders are greater than those for conventional tunnelling. If (as is likely) the disadvantages of mechanical methods continue to be reduced at a greater rate, the swing away from drilling and blasting will gain momentum.

Jan 1, 1987

This paper deals briefly with the geology and mineralisation of the Ediacara Mineral Field, which is located about 300 miles north of Adelaide in the Mount James Range.The field was discovered sane time prior to 1872. Total recorded production for the field amounts to a few hundred tons of lead and 36 tons of copper. Re-listing of the field during 1961-62 led to its classification as a Mississippi Valley type deposit. Diamond drilling has partly outlined the spread of mineralisation and confirmed its stratiform distribution,Sources for the metals are suggested and various possible mechanisms. of deposition are described.

Jan 1, 1963

By Veloso L, Alvarez O, David D

Cerro Colorado operations The Cerro Colorado Mine is located 150 km east of Iquique in the Atacama desert of northern Chile. The mine is wholly owned by Rio Algom Limited of Canada and produces copper metal using a bio leaching process. Tw

Jan 1, 1998

By Ault A. R

The recent modernisation program at the Risdon electrolytic zinc smelter of Pasminco Metals - EZ (PMEZ) inyolved significant changes to the composition of cell electrolytes. The most significant were increased acidity and sulphate level, a reduction in Co level, and the replacement of 2-naphthol in the additive mixture with licorice. In determining acceptable operating ranges, a relatively large number of industrial deposition tests under controlled conditions was required. The cathode zinc deposits so produced were examined in terms of overall appearance, crystal structure according to X-ray diffraction, and a micro-roughness parameter. Beginning with typical deposits produced in the presence of an excess of one of the addition agents glue or antimony or a mist suppressant (licorice or 2-naphthol), a simple classification system was developed. In this system, the deposits are divided into the following types: Doughy, Pinholed, Compact and Stressed. There was a weak correlation between deposit type and crystal orientation. In terms of ease of stripping, observations in plant operations showed that only Compact and Pinholed were consistently acceptable. Current efficiency was normally maximised by producing a Compact deposit. Process variables such as zinc concentration, temperature and the use of strontium carbonate were found to cause changes in deposit type if the reagent mixture used was unchanged. From the knowledge gained, guidelines were developed to allow glue and antimony additions to be altered to fit new circumstances. The simple classification system was first used to expedite recovery from undesirable morphologies and then to optimise individual cell units operated under substantially different conditions. It is believed that finer control could be exercised by determining the micro-roughness of Compact deposits. However, difficulties can arise if sudden, large deviations occur and go undetected. Suggestions are given for an improved additive control system. The classification system developed has been compared with published information in the literature, and good correspondence was noted suggesting a predictable relationship between short-term, laboratory deposition tests and observable phenomena in industrial electrowinning cells run under steady conditions.

Jan 1, 1993

By Albano C, Antila A, Flykt B

A method for relating operating variables and dewatering parameters of Thunes disc filters in the LKAB pelletizing plant at Malmberget in Sweden, via empirical mathematical models is described. Near orthogonal experimental design was used, where all independentvariables were allowed to span over their domain of variation and pseudo-randomly distributed among the experiments. The dewatering parameters are dependent on many variables and instead of using a traditional mechanistic model, an empirical model based on multivariate data analysis was chosen. The way of expressing the relation is by regression coefficients obtained from partial least square regression (PLS). Two empirical models were generated. The models were validated using an extra set of 56 experiments. The dewatering parameters were related to the design variables with few experiments, and user-friendly response surface methodology was used to determine the optimal conditions.

Jan 1, 1989

By Robinson WB

An accurate and rapid assessment of coal resources, such as that provided by computer modelling, forms an intergral role in evaluating CSR's coal deposits for future development. An in-house system utilising a number of geological, engineering, costing and financial evaluation routines has been developed for DEC VAX computers. The system is currently being upgraded and enhanced to meet the demands at the various mine sites. Computer modelling of the geology is performed on encoded drillhole information and coal core chemical and physical analyses. A conceptual mine plan is formulated then digitized and superimposed on the geological model. Insitu and product coal reserves and qualities as well as overburden and parting quantities are then calculated for each strip or block. These strip parameters are then transferred to the mine scheduling routines to determine the most efficient mining sequence for the mine plan. Cost factors and scheduling data for equipment specified in the conceptual mine plan are used in the mine costing subsystem. The financial subsystem then evaluates the likely return on investment. Future enhancements to the system include improvements in the response time through the introduction of interactive graphics, the direct interfacing of geophysical and analytical data, and further development of a geotechnical'database.

Jan 1, 1983

By A M. Wala, H W. Wu

A research project incorporating a number of mine site exercises to reduce the effects of fire incidents and possible consequent health and safety hazards has been undertaken focused on the application of mine fire simulation software packages for contaminate tracing and fire modelling in coal and metalliferous mines. This paper examines aspects of introduction of inert gases to underground workings to aid recovery of a mine following a fire. Broad conclusions from work undertaken at individual Australian coal mines are discussed as examples. The effort is built around the introduction of the fire simulation computer program æVentgraphÆ to the Australian mining industry and the consequent modelling of fire scenarios in selected different mine layouts. Case studies have been developed to examine usage of inertisation units and particularly application of the GAG jet engine unit. One example has focused on selection of the best surface portal location for placement of the GAG for most efficient suppression of a fire. A second has examined a situation with significant seam gas being emitted on the face. This has shown that under certain face dip angles stopping the mine surface fan to reduce dilution of GAG exhaust gases will cause reversal of face air and consequent mine explosion as gas laden air is drawn across a fire. A third examines inertisation and dilution issues in mains headings. mains headings present a complex ventilation network with often numerous parallel headings, hundreds of cut-throughs and a variety of ventilation control devices. In such a complex system (with additional interference from a fire), maintaining control of the movement of inert gas is more difficult than elsewhere in the mine. Some illustrations of this issue are given.

Jan 1, 2005

By Simpson D, Skopakow J

This paper is one of the series of papers relating to the Melbourne Underground Rail Loop and specifically describes the structural and architectural design of Museum Station. Structural arrangement, loads and design methods of the major temporary and permanent works are briefly described for the main station and entrance works. Planning of the station concourse area, booking halls and entrances are described together with the selection of finishes for all above and below ground areas.

Jan 1, 1981

By Marshall T, Nicholson DS

Reserves of high-grade quartz gravel, lignite and timber suitable for the production of silicon metal and ferrosilicon on large scale occur within 40 miles of Bluff Harbour. Undeveloped hydroelectric power resources on the Clutha River are located within 50 miles of the most promising quartz gravel deposits while ooencastable lignite, potentially suitable for electric power production, occurs in the same locality as the quartz gravels. A preliminary study of production economics indicates that the commercial feasibility of silicon/ferro-silicon production would depend mainly on the cost of electric power, total capital cost of plant, and the market value of the products. The proximity of Bluff Harbour is advantageous for the export of products.

Jan 1, 1971

By P Waters

BHP Billiton Iron Ore initiated a program in January 1995 at the Mt Whaleback operation in Newman, Western Australia to develop a closure plan for the overburden storage areas (OSA), which have the potential to generate acid rock drainage. The primary research program includes the development of technology for the long-term performance of OSAs with respect to slope stability, surface run-off, erosion, water infiltration and vegetation. The objective is to control acid rock drainage by preventing moisture movement into and through the OSA material. Infiltration to the underlying OSA material and closure costs are minimised due to the presence of the run-of-mine (ROM) cover material. A summary of the field data is presented to illustrate low percolation rates to the underlying OSA and key performance characteristics of the moisture store and release cover system design. Field data collected to date demonstrates that a moisture store and release cover system constructed with suitable ROM material has good potential as a final cover system at the Mt Whaleback site. The performance of the cover system on a sloped surface was significantly different as compared to placing the cover system on a horizontal surface.

Jan 1, 2003

By R Valenta, J Owen, D Kemp, E Lebre, G Corder

Copper plays an essential role in our society. It is one of the key materials supporting economic growth and human development in emerging economies, for its common use in construction, power generation and transmission. It is also a critical metal for the transition to a low carbon future, particularly for its uses in renewable energy and electric vehicles. As a result, global demand for copper has been increasing steadily and is predicted to continue in the future. The demand-supply gap is currently growing, and new mines will be needed to fill it. This project observes the current pipeline of copper mining projects, which are characterised by technical complexity (lower grades, deeper deposits, complex mineralogy etc.) but also environmental, social and governance (ESG) complexities. A common assumption in the mining industry is that a rise in copper prices will unlock these deposits. However, while most technical complexities are price sensitive and are likely to be overcome in favourable economic conditions, the influence of ESG complexities is more difficult to evaluate. CITATION: Lebre, E, Valenta, R, Kemp, D, Owen, J and Corder, G, 2018. Accounting for social and environmental complexities in mining project developments: the case of copper, in Proceedings Complex Orebodies Conference 2018, pp 39–40 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

The excavator selection process is quite complex due to the large number of influencing factors, many of these are variable and difficult to accurately define. The majority of mining companies prepare a tender of general specifications and suppliers will then match a product to those specifications. The mining company will then evaluate the tenders on the basis of the best available deal. In this paper, the importance of open pit excavator selection in terms of its impact on operating costs is analysed and discussed. A rigorous process for selection is then outlined.

Jan 1, 2003

By Hongzhen Yu, Xiaoping Ma, Jiansheng Qian

The paper introduces the design of an Intelligent Managerial Attendance Machine (IMAM) for coal mines. In the system, data communication is carried by Optical fiber communication, including industrial control computer on the ground and the car

Jan 1, 1998