Search Documents

By C F. Nichol, L Smith, R D. Beckie

A better understanding of the hydrogeology within mine waste rock and cover systems is essential for the quantification, prediction and prevention of metals loading to the environment surrounding waste rock piles. The effect of surface condition on the internal flow mechanisms within an intermediate-scale constructed waste rock pile is being investigated at the Cluff Lake Mine, Saskatchewan. Changes in the water balance, the outflow distribution and water residence time have been observed in the waste rock pile following successive modifications of the surface condition. The three year old, run of mine, free-dumped surface was ripped to a depth of 30 cm to 40 cm, and levelled in October of 2001. In August 2002, a 10 cm to 15 cm cover of compacted waste rock was placed on the pile. Outflow, precipitation and run-off data collected during natural and artificial rainfall events have been used to quantify the maximum infiltration rate, and the spatial pattern of discharge and cumulative volume of water that infiltrated into the waste rock under each surface condition. Infiltration data together with the outflow data provide a basis to address the residence time of water within waste rock and the dominant flow mechanisms for different surface conditions. With a free dump surface spatially distinct wetting fronts are observed at the base of the pile that vary in flow rate by an order of magnitude (measured at a 2 m by 2 m scale) and in time by up to a week. Following ripping and levelling, similar cumulative outflows were observed, but the magnitude and arrival time of wetting fronts changed across the pile. A decrease in outflow volume, a decrease in infiltration volume, a two-fold increase in the response time of wetting fronts and a more spatially uniform distribution was observed following placement of the compacted surface layer. Based on preliminary data, the internal structure appears to be the dominant factor controlling outflow variability.

Jan 1, 2003

To counter depressed world nickel prices, a continuing effort is being made at Kalgoorlie Nickel Smelter to reduce unit production costs. One major area in which production costs can be reduced is the substitution of coal for fuel oil. Two areas where this has been achieved to bring about a saving are, the addition of coal to flash furnace flux to reduce supplementary fuel oil requirements in flash smelting and the replacement of two oil-fired air preheaters with a coal-fired unit. These actions have resulted in coal replacing 67% of the current fuel oil requirement in flash smelting at the Kalgoorlie .Lckel Smelter.

Jan 1, 1987

By Davis A, Song J

A review of the literature indicated that several studies have been reported on the dissolution of gold using iodide/iodine, bromide/bromine leaching systems. Although the reagent costs are much cheaper for chloride/chlorine (or hypochlorite) this system has not been fully evaluated. This study was conducted to evaluate the fundamental chemistry of the chloride/hypochlorite leaching system. The CHEMIX program was used to model the stability of various gold species existing in the solution. The gold dissolution rate at different conditions was determined using gold strips immersed in various mixtures of chloride/hypochlorite. Leaching experiments were conducted to test the extraction of gold from various ores (oxidised and copper-gold ores), showing a promising prospect for this technique in various applications.

Jan 1, 1992

By L Rattmann, T Katz, J B. Pateiro-Fernßndez

Carbon capture and storage (CCS) is expected to become one of the main technological instruments for mid-term reduction of CO2 emissions into the earthÆs atmosphere. Besides the reduction of CO2 emissions into the atmosphere, the implementation of CCS would have various negative consequences, which are û if at all û only poorly covered in the current socio-political discussion. Taking into account all aspects of CCS, the outcome of a comprehensive and conclusive assessment of CCS against the background of the sustainable development concept is uncertain. When assessing the overall impact of CCS in a holistic approach, a variety of aspects with effects on sustainable development are affected. Besides economic issues, various other effects of implementing CCS should be taken into consideration. These include for example additional costs for CCS facilities and processes and a decrease in powerplant efficiency due to high energy requirements of capture processes, and various ecological and societal aspects, such as higher demand for combustible, resulting in faster depletion of reserves and higher land and water use and the provision of jobs along CCS technology chain. This paper presents an approach for a structured sustainability assessment of CCS based on the multi attribute decision-making (MADM) method analytical hierarchy process (AHP). The functioning of the presented methodology is exemplified at the case study of a German coal fired powerplant.

Jan 1, 2009

Preliminary petrographic investigations of eight Upper Permian coal seams of the Muja sub-basin, Collie Coalfield, reveal that the coal is high in inertinite and relatively low in vitrinite and exinite contents. The exinite content of Collie coal is relatively high when compared to other Australian coal of similar age. In addition the mineral matter content of the coal is very much lower than comparable Permian coal of Eastern Australia. The higher exinite content could be attributed to the type of Glossopteris flora, and the lower mineral matter content to the environment of deposition postulated for the Collie Coal Measures.

Jan 1, 1982

By Terrill JE, Fergusson LJ

In the last decade of precious metal exploration, several important gold discoveries have conclusively demonstrated that epithermal gold deposits formed in what were once active geothermal areas. A significant deposit in this category is the Lihir Island discovery in the Tabar-Ferri volcanic island arc off the coast of New Ireland, Papua New Guinea. Within that arc are the Feni Islands where exploration by Esso PNG Inc. and City Resources Ltd. has been carried out since early 1984. On Ambitle Island in the Feni Group, an epithermal gold prospect located within a young caldera has been tested by diamond drilling. The drillholes intersected a boiling zone at depth beneath acid altered 'cap' rocks. The zone is 30-60 metres thick and comprises hydraulically fractured and mineralised lavas with gold grades of 1-7 g/t. The prospect is still an active geothermal area with current boiling in the zone tested. As on Lihir, the recent epithermal alteration and mineralisation overprints a relict prophyry system. On Ambitle and the adjacent Babase Island several other, cooler exciting gold prospects are currently being tested.

Jan 1, 1987

By S Miller, A Neale

As part of a long-term acid rock drainage (ARD) mitigation study, PT Freeport Indonesia has completed the construction of a highly instrumented, full-scale, experimental, overburden stockpile to further evaluate the behaviour of the waste rock system at Grasberg mine. A total of 24 lysimeters, 30 sets of thermistor strings and 48 oxygen-sampling ports were installed at select locations during stockpile construction. ARD flow rates and chemistry have been recorded since the start of overburden rock placement in April 2000. Measurements of in situ temperatures and oxygen concentrations quantify reaction rates and the oxygen pathways that control oxidation kinetics deep within the waste rock profile. Direct field observations show the significance of advective oxygen flow with respect to the onset of oxidation kinetics. Oxygen measurements show that the rubble zone that forms at the base of a waste rock bench provides a critical pathway for oxygen entry to the waste rock profile. Furthermore, rapid oxidation as evidenced by measured temperature increases deep within the panels of waste rock is observed to occur. The observations presented in this paper provide critical insight for understanding the mechanisms and behaviour of full-scale waste rock stockpiles with respect to ARD generation. The results of this program will assist in the future selection, testing and evaluation of appropriate mitigation measures with respect to surface and face treatments to reduce long-term ARD generation. This project is a work in progress, and at least another two-years will be required to fully understand site-specific ARD generation and ARD mitigation mechanisms. This paper will discuss various design and construction considerations, provide an overview of results achieved to date, and some preliminary interpretation of what is happening within the overburden stockpiles.

Jan 1, 2003

Mining in Guyana dates back into antiquity and a brief history of gold and diamond mining and of the small-scale miner, the pork-knocker, is given. The gold and diamond deposits found on the beds and in the flats of old and present rivers and the current methods of investiga- ting these deposits are briefly described. Methods of mining these deposits including the small-scale hand methods of pitting and diving with or without helmets are also briefly described. 'The small-scale method of dredging using a suction dredge in conjunction with a diver is described in more detail, from its develop- ment to current practice, without giving too much mechanical and technical details. The organisation of the industry and the mining titles, laws and policy relating thereto are reviewed. A brief account is given of the socio- economic role of the industry. Conclusions are made regarding the need for improvements in existing equipment and financing and for incentives to stimulate production. The future outlook of the industry is con- sidered.

Jan 1, 1986

Rajasthan of western India blessed with rich base metal and phosphorite deposits. The biogeochemical and geobotanical methods of mineral exploration are greatly used in parts of Rajasthan Zawar, Khetri and Ambaj multi-metal project Gujarat and Jhamarkotra phosphorite deposit. These principles are exclusively based on certain assumptions about the anomalous chemical composition in plants and distribution and migration of indicator elements. Biogeochemical studies for lead zinc deposit of Zawar group of mines were carried out to locate the probable accumulators which could help in prospecting for these metals. The important roots of Impatiens balsamia plants contain 735 mg. of cadmium and crotolaria linifolia 603 mg., melhania futteyporensis 626 mg. lindenbergia muraria 443, celosiu argentia 360 mg. In the Khetri copper belt the vegetation is scanty and the species includes Acacia arabica, zyzypus jujuba and cactus euphorbia.

Jan 1, 1988

By Larsen E. R

We discuss the concept of optimal cut-off grade policies and their advantages in terms of maximisation of net present value of mining operations. There are indications, however, that such optimal policies are not widely used in the mining industry. In order to explore why this is the case we identify a number of stakeholders who may have diverging interests in the operating policies of a given mine. These various interests are mapped and a number of important relationships are explored in a large qualitative systems dyanmics model.

Jan 1, 1995

The cost of production from truck and loader fleets is influenced by management development of the culture of the organisation, work practices, systems and procedures of the production and maintenance teams. Establishing if the cost of production is the best that can be achieved then requires the measurement of results against established standards of performance. This paper provides a series of discussion points of the factors that influence the cost of production from men and machines for large scale open pit mining operation and provides some suggested performance standards in the form of Benchmarks. Most of the references have been drawn from established large scale deep pit mines in USA, Canada and Australia which have had to implement and constantly fine tune cost efficiencies in order to survive. The discussion provides:ò a review of priorities or the relative importance of the various cost elements for a mining system;ò suggestions of systems and procedures for the operation and maintenance of machines which are considered to yield the best overall results;ò examples of operations that have developed and implemented management systems and controls that are achieving good results in specific functions; andò suggested benchmarks of performance.

Jan 1, 1992

By Teague JWS, Jung RF, Kadletz O, Jones DR, Jones CJ

A study of the passive treatment system for Hilton minewater revealed that it consists of four main process steps. The water, which contains soluble and particulate iron and zinc and is supersaturated with CO , is pumped to the surface and then passes throuqh a degassinq unit into settling ponds where larger particles of iron hydroxide, containing some adsorbed zinc, can settle out. The still turbid supernatant is pumped to the top of a hill, from where it is allowed to trickle in a broad sheet, releasing CO , towards an earthen channel in the valley below. Consequently the pArises from around 6 to 7.5. This in turn promotes further decrease in the concentration of soluble zinc by increased adsorption of zinc on to iron hydroxide particles. The channel then transports the water to the third process in the system - a 53 ML pond acting primarily as a flocculation-sedimentation basin. The clarified water overflows into a second channel, downstream of the pond, which constitutes the fourth process in the system. Here, copious quantities of filamentous algae further reduce zinc concentrations to acceptable levels before the water is collected for recycle into mine operations. The work reported here represents a detailed study of this system and describes the optimisation of the operation of each of the individual steps involved.

Jan 1, 1988

By G Senanayake, J Andreazza

The general experience in gold cyanidation research activities and plant practice is that high oxygen and cyanide concentrations improve gold leaching kinetics which in turn reduce residence time and increase throughput. This paper shows how the improved pre-oxidation method for the pyrrhotite rich gold ore of Bounty Gold Mine has increased gold recoveries at lower reagent consumption rates. The installation of a pipe reactor, in conjunction with a Multi Mix Systems oxygen injector, has lowered the amount of oxygen required to achieve a dissolved oxygen level target of 20 mg/L. The improvement of the pre-oxidation stage and lead nitrate solution addition has led to a reduction in the free cyanide concentration required for leaching, resulting in a decrease in cyanide consumption rate by 36 per cent to achieve a one to two per cent improvement in the gold recovery.

Jan 1, 2002

By L Soares, W T. Hennies, F Fujimura

A methodology of environmental performance evaluation in mining developments is proposed, as well as guidelines and procedures for obtaining information to improve their environmental performance. Environmental performance is the results of the mining activities and their relation to environmental issues. If this evaluation is carried out on an on-going basis, it is possible to anticipate or to identify the formation and development of an environmental impact in its early stages. Evidence or trends identified by environmental evaluation provide valuable information to prevent further damage. The proposed methodology is based on the significant environmental aspects of a selected monitored job site by environmental indicators which are then compared with previously defined environmental criteria and targets or goals. The methodology procedures also take into account the environmental accounting of the investments and expenditures.

Jan 1, 2003

By Scherbatsky VB, zon BM, Babushkin NM, Kitaev BI, Shabel&apos

The structure and hydrodynamics of the raceway zone of a blast furnace was studied on a cold model representing a sector containing two tuyeres. The model differed from the usual in that it was prov- ided with continuous flow of the coke layer at pre- determined rates, had provision for changing the tuyere parameters (diameter, protrusion, inclinat- ion) and irrigation of the layer with liquid. A combination probe was developed which per- mitted simultaneous measurement of the pressure field both across the area and through the height of the layer as well as determining the topography of the raceway. The velocity fields in the layer were measured with a specially made impulse thermo- anemometer. The determining criteria of the model were taken as the relationships between the energy of the blast and the particles, the dimensions of the raceway and the cross-section of the tuyere. The model established the effects of the tuy- ere structural parameters, blast parameters and amount of liquid products of smelting on the con- figuration of the raceway, the structure of the layer, pressure and velocity fields in the vicinity of the tuyeres and in the vertical direction through the layer. The properties of the raceway formation and the structure of the layer in motion have been clarified.

Jan 1, 1981

The provision of electrical power is an important consideration in project develop- ment. The first step to be taken in this area is to assess the power requirements of the project. The alternatives of taking a supply from a power authority or providing local generation can then be considered. This requires additional definition of the prob- able characteristics of the supply. The availability of authority power in Australia is limited by the extent of the state power grids. Recent developments now allow these grids to be extended and their load capacity increased to meet major load increases at less cost than was possible pre- viously. The options for local generation include diesel, gas turbine, steam, hydro, solar and wind, each having its particular performance characteristics and costs. The choice of fuel for diesel, gas turbine, and steam plant likewise involves consideration of a range of factors. The arrangements adopted for a number of development projects illustrate some of the aspects which influence the decisions on power supply.

Jan 1, 1986

Nickel ores from three different mines, Digger Rocks, Cosmic Boy and Flying Fox, are treated at the Forrestania concentration plant. The ore types vary from oxidised supergene ores to primary pyrrhotite+pentlandite ores. Mineralogical investigations on the ore and process samples have been carried out in different stages of process development. One of the studies was done with the samples collected from the flotation circuit in 19 June 1994 when the Cosmic Boy ore was processed. The process products were screened, and the size fractions were analysed for the main elements by appropriate analytical methods. Mineralogy of the products was studied microscopically and composition of the sulphides was analysed with an electron microprobe. Liberation of the main sulphides in the flotation feed was determined with the point-counting method, and weight percentages of the minerals were calculated using chemical and mineralogical data. The typical sulphide assemblage of the Cosmic Boy ore is violarite, pentlandite, pyrite, pyrrhotite and chalcopyrite. Violarite dominates over pentlandite (ratio being 70 per cent to 30 per cent), and pyrrhotite is strongly replaced with pyrite and magnetite. One of the most common mineralogical features of this ore type is secondary magnetite, which occurs as narrow rims in porous violarite or in association with secondary pyrite. Serpentine, talc and chlorite are the main gangue minerals. In the milled feed (76 per cent -74 ¦m) locked particles between nickel and iron sulphides are common. About 41 per cent of total pentlandite occurs as pure liberated particles, and 33 per cent as locked grains with violarite. Liberation degree of violarite is 55 per cent, and the most common type of locked particles is violarite+magnetite, carrying about 20 per cent of total violarite. To achieve a recovery of 80 per cent for pentlandite, all the particles containing at least 50 vol-% pentlandite should be floated into the nickel concentrate. Correspondingly recovery of 80 per cent can be reached for violarite if all the particles containing at least 65 vol-% violarite are floated.

Jan 1, 1996

The patterns of flow of reaction gases through the flash furnace at the Kalgoorlie Nickel Smelter were simulated in a 1:20 scale model using a flow of water. Particular features of the flow down the reaction shaft, through the settling chamber and into the uptake leading to the waste-heat boiler were examined. Inferences were made concerning the effects of the patterns of flow on the efficiency of the smelting reaction, on the entrainment of dust by the gas stream and on the erosion of the refractory lining of the furnace. In addition, the effects of geometrical modifications to the arrangement of the concentrate burners and to the profile of the settling chamber were explored by making these changes to the model and observing the resulting variations in the patterns of flow.

Jan 1, 1991

By Hunter T. C

The wirebar furnacing and casting facility commissioned in 1970 at Copper Refineries Pty. Ltd. (CRL), Townsville, comprising a 70 tonne/ hour ASARCO shaft furnace and a Walker type casting wheel, contained several unique design features. Since commissioning, effort has been directed at improving metallurgical control of the casting process. This has resulted in the identification of optimum mould lubricant properties and the use of continuous on-line measurement of molten metal oxygen content. Casting defects such as cracks and surface porosity are readily explained and controlled using these techniques.

Jan 1, 1977

By Kepplinger W

The COREX process is a technology for production of liquid hot metal on the basis of coal (without the use of a coking plant) developing by VOEST- ALPINE AG, Austria and its subsidiary company Korf Engineering GmbH, Federal Republic of Germany. CORED is a registered trademark of VOEST-ALPINE AG and Korf Engineering GmbH. The COREXW process is based on the idea of separating the process steps realized in the blast furnace (gene- ration of reduction gas, reduction of iron oxide and melting of the reduced iron) and including partial coking of the coal.

Jan 1, 1987