Search Documents

By G J. Jameson, A Agarwal

This paper is concerned with the observation and analysis of bubble clusters in a laboratory flotation cell. A device was used in which bubbles were allowed to rise in clean water containing the same frother and collector concentration as in the cell. Bubble clusters were recorded using a high speed camera and analysed using an image analyser. Dodecyl amine was employed as a collector to float silica. The effect of impeller speed on the cluster behaviour was investigated. The results were interpreted in terms of cluster diameter and shape factor. The sizes of the bubbles forming the clusters were also measured and compared to the sizes of the independent bubbles in the cell. It was found that there was an optimum impeller speed in which the cluster diameter was a maximum. Higher agitation and the consequent higher power inputs resulted in cluster break-up while lower shear rates promoted cluster formation.

Jan 1, 2005

The paper reviews some characteristic features of feasibility studies and discusses the need for a wide scope at the pre-feasibility stage. The performance of recent Australian gold mines against the predictions contained in their respective feasibility studies is examined, resulting in a recommendation that feasibility studies need to be improved The advantages to be gained from having a feasibility study reviewed by an independent authority are discussed, and some of the reasons for using consultants are listed. Two examples of successful optimisations in the early stages of pre-development studies are described briefly and the benefits achieved are presented. The paper concludes that feasibility studies need improvement to enhance the confidence of investors in the mining industry.

Jan 1, 1991

Heavy medium separation is widely used because of the precision of separation achievable and the flexibility of control. Good design is manifest in the eventual achievement of the operational objectives. These objectives which take account of the assessed quality of raw feed, market requirements and production cost levels need to be carefully prepared and realistic.

Jan 1, 1987

The techniques originally developed to process digital images of Mars, later gained widespread acceptance when applied to Landsat data: they are now making a significant impact in fields of geology outside remote sensing. The three ingredients of success are seen to be firstly, the perceptual attributes of image displays and the use of colour; secondly, the absolute ability to register data from a variety of sources; and thirdly, the speed of specialist "interactive" digital image display systems. The future lies in further exploiting these attributes through a Geographic Information Systems (GIS) approach to data handling, integration and display.

Jan 1, 1986

By M W. Chen, I Canbulat, S Saydam, C G. Zhang

The height of fracturing (HoF) measures the propagation distance of continuous fracturing from the mining horizon and is also termed the height of cracking (Hebblewhite, 2020; Khanal et al, 2019) or hydrologically the height of groundwater drainage (Tammetta, 2013). In longwall practice, HoF is an important predictive indicator for assessing the dewatering effect of panel extraction on the shallow aquifer and surface flows. The HoF determination is basically dependent on field measurement works, typically using surface extensometer, borehole televiewer imaging, piezometer monitoring, packer testing, borehole breakout logging, and isotopic tracer monitoring (Brown and Walsh, 2022; Corbett, 2022; Hebblewhite, 2020; Holla and Armstrong, 1986; Mills and O’Grady, 1998; Walsh et al, 2022a, 2022b). These methods or tools have been widely applied to observe rock fracturing and groundwater responses to longwalls at Australian coalmines, for example, Dendrobium Mine (Brown and Walsh, 2022; Walsh et al, 2022b), Appin Mine (Walsh et al, 2022a), and Springvale Mine (Corbett, 2022). In Chinese mines, borehole televiewer imaging and packer testing are more frequently used due to convenient instrumentation, quick testing, and not requiring long-term maintenance of the instrumentation boreholes. The HoF determination also involves further raw data interpretations, for which specialist software for data extraction and quantitative criteria for bounding the fracture transition and termination are necessary. By combining the measured fracture distribution and longwall parameters regarding panel geometry and geological settings, several HoF models have been developed for conceptualising the understanding of strata depressurisation and providing mine engineers fast calculation tools for HoF prediction. The Mackie model considered the height of fracturing as the upper bound of fractured zone and revealed that within the fractured zone there are highly connected fractures and accordingly porosity enhancement and groundwater depressurisation, where the fracture network can be less transmissive from the mining horizon up (Hebblewhite, 2020). The fractured zone shares similar fracturing regime but different heights in varying models: HoF is 30 to 58 times of the mining height (t) based on Australian, Soviet and UK experience (Kendorski, 1993, 2006), and 21 to 33 t according to the field measurements in NSW Central Coast, Australia (Galvin, 2016). Some Australian longwall mines adopt Ditton model (Ditton and Merrick, 2014) (Equations 1.1 and 1.2 in Table 1) sourcing from NSW coalfield experience for HoF prediction, while Liu model (Liu, 1981) (Equations 2.1 to 2.4 in Table 1) developed from 27 coalmines in China is frequently used by Chinese coalmines.

Nov 29, 2022

This paper describes the effects of physical variables in dewatering of mineral slurries with air as the filtrate displacing medium. Using a mathematical model with material related constants measured in laboratory dewatering curves are simulated for vacuum and pressure filtration. Four different mineral slurries are studied. Basic dewatering curves with variation in air-pressure are shown with iso-energy lines. Variables such as air pressure, feed concentration, cake thickness and cake formation pressure are discussed.

Jan 1, 1989

By E V. Man, O N. Savassi, J-P Franzidis

In flotation, the property that is exploited to effect the separation of a mineral from an ore is referred to as its floatability. Assessment and quantification of ore floatability is of fundamental importance in modelling and simulation of flotation circuits. This paper describes the design, construction and operation of a new laboratory flotation rig that has been developed at the Julius Kruttschnitt Mineral Research Centre (JKMRC) to determine the floatability of different ores on a small-sale. The rig is designed for continuous operation. The major features of the rig are highlighted in this paper. An unique characteristic of the rig is a 9.1 L conditioning vessel. This provides a mixing regime close to plug-flow which avoids complications such as different collector coverages for similarly sized particles (which would considerably increase the complexity of ore floatability determination). The main advantages of this rig when compared to conventional batch flotation cells include better control of the chemical environment and the ability to determine froth recovery, entrainment and water recovery with increased accuracy. Preliminary tests undertaken with a high-grade lead/zinc ore from BHP Cannington are presented demonstrating the good level of reproducibility obtainable in operating the equipment.

Jan 1, 2000

By Barnett LJ

The Kellogg slag fuming model is extended to apply to the Port Pirie plant which uses recuperative heating of secondary air. Exten- sive investigations of plant operations pro- vide parameters for use with the model, and verification that the resulting model provides simulation which is very close to actual plant performance. The model is used to_deter- mine optimum slag fuming operating conditions, and the results of several other investigations with the model are briefly described.

Jan 1, 1975

By Fry P. R

Dragline operations have played a major and successful role in coal mining around the world for more than 30 years. Because of this long history, many of the operating draglines are reaching an age where maintenance and downtime costs are prohibitive, and decisions need to be made to either replace or refurbish them.In the current economic climate, refurbishment is a popular choice and this usually involves major structural repairs above and below the roller circle, together with replacement of the roller circle components. Often, the dragline tub is also replaced by a completely new one.

Jan 1, 1992

By Kasaneva S

The San Cristobal gold district is located 110 km east of the port of Antofagasta, Chile. It contains the San Cristobal gold mine, where Niugini Mining Ltd. commenced a heap leach operation, with initial reserves of 10.1 million tonnes grading 1.34 g/t An, in December, 1990. The San Cristobal district occurs within an upper Cretaceous-lower Tertiary magmatic arc. The main mineralisation occurs within a northwest trending subvertical zone, 1km long and 70-100 m wide, which contains rhyolite porphyry and minor breccia, and is locally termed the "subvolcanic complex". At the San Cristobal mine, most gold mineralisation occurs in subvertical quartz-pyrite veins which were emplaced in dilational sections of an imbricate fault system. The bulk gold resource comprises four ore shoots which formed where the vein system intersects the subvolcanic complex. Gold-bearing quartz-pyrite veins also occur at separate prospects, the Three Sisters and Sol prospects, west and south of the San Cristobal mine. Hydrothermal alteration consists of potassic and propylitic assemblages related to intrusion of the subvolcanic complex. This alteration is overprinted by a phyllic stage which is associated with the emplacement of the quartz-pyrite veins. The oxide zone is 180 m thick, and contains native gold, electrum, limonite, and manganocarbonates. The underlying hypogene zone contains pyrite with minor chalcopyrite, sphalerite, galena, covellite, bornite, chalcocite, and arsenopyrite. Fluid inclusion studies indicate that the deposit formed at approximately 270¦ C, and the mean salinity of the fluid was 4% NaCl equivalent. These observations enable the San Cristobal deposit to be classed as a porphyry-related, mesothermal quartz-vein system of the low sulphidation type.

Jan 1, 1995

By Evans A. F

Arising out of the increasing demands for efficiency in modern ore-dressing operations has grown a requirement for fuller knowledge of the characteristics of the ore treated. In part, this is being met by improved methods of study of the mode of occurrence of the constituent minerals, and of the intricacies of their physical relationships.A typical instance of the need for such a study is the presence of some undesired mineral in a flotation concentrate or tailing, which may be due either to mechanical association through insufficient grinding, or to incomplete separation in the flotation operation.Again, with modern practice in fine grinding, which often requires that from 70% upwards of the ground ore shall pass a 200-mesh screen, it is obviously impossible to obtain data on comparative grinding efficiencies, for instance, unless there is adequate knowledge of the size-composition of the material passing the finest available screen.Studies like these can be made satisfactorily only after size-separation (which may be carried out conveniently by elutriation) and by actual visual examination with the aid of a microscope, and the minute size of the mineral grains to be examined has necessitated the development of a new technique of sizing and microscopic examination.

Jan 1, 1932

By D W. Airey

Frictional rock bolts are widely used because of their low cost. However, they have a thin wall section that makes them prone to corrosion, and they cannot be relied on to provide long-term ground support. It is difficult to assess the capacity after the bolts have been installed as they can only be pulled out if this has been allowed for during insertion. The questions of how long can the rock bolts function effectively and the effectiveness of various surface coatings, which can have significant cost implications are, investigated in this study.A series of accelerated corrosion tests have been performed on frictional rock bolts. The rock bolts, typically 900 mm long, have been inserted into concrete cylinders produced using a styrofoam insert to create the hole for the bolt insertion. Strata rock bolts with four surface coatings have been tested: uncoated black steel, galvanised, enduro (plastic coated) and coated with a proprietary aluminium/zinc alloy. Tests have been performed on two diameters of bolts. Following insertion of the bolts, the concrete cylinders were placed in a large drum filled with saltwater and current was applied to accelerate the corrosion process. The rock bolts were then extracted at various times after the commencement of corrosion. Comparison of the insertion and extraction resistances shows that corrosion initially increases the bolt resistance and that substantial section loss is required for the bolt resistance to drop significantly.CITATION:Airey, D W, 2014. Laboratory corrosion tests of frictional rock bolts, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 257–262 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

Agglomeration pre-treatment is a new process now being used here and overseas whereby problems arising with the heap leaching of gold and silver from materials containing critical amounts of fines or clay can be simply and cheaply overcome. The technique involves mixing the material with a suitable binder, commonly Portland Cement, and tumbling the moistened material to agglomerate the fines. These agglomerates are placed on the leach pad and cured prior to leaching. Test results, plant and operating cost data are presented. INTRODUCTION Heap leaching is a low capital and operating cost alternative to conven tional processing techniques for gold and silver extraction. A number of commercial-scale operations have recently started in the United States and the method is being considered for further deposits there and elsewhere.

Jan 1, 1982

By Z Zhao

Coal dust is hazardous to underground coal workers and water spray is the most common and economic method for controlling coal dust. Previous studies proved that the addition of surfactants can improve the performance of water spray on coal dust suppression. The evaluation methods for surfactants vary from different studies. The zeta potential test is a common method for evaluating surfactants with ionicity. Generally, the suspension of coal dust with pure water usually showed a negative value of zeta potential. The addition of cationic surfactants can increase the zeta potential to a positive value with a small dosage, while the addition of anionic surfactants can only lower the zeta potential. However, there is a lack of comprehensive study to investigate the relationship between the zeta potential and the suppression performance for coal dust. The aim of this study is to reveal the consistency and discrepancy between the zeta potential and the suppression efficiency of a surfactant. Firstly, the mixture of cationic surfactant solutions and coal dust would be evaluated by the zeta potential test. The wind tunnel tests would then be conducted for the same surfactant solutions to measure and calculate the suppression efficiency. It was found that the addition of surfactant can increase the zeta potential and the suppression efficiency and it reached the greatest efficiency when the zeta potential approached to zero. The equilibrium of zeta potential can benefit the suppression performance of surfactants in the wind tunnel test. The result of this study can achieve a better understanding of the mechanism for coal dust suppression. The selection of surfactants will also be suggested for researchers or industries in terms of coal dust control. It would be more economic if a similar performance could be achieved by less consumption of surfactants.

Oct 12, 2022

By O Aydan, R Ulusay

Blasting is the most commonly used excavation technique in mining and civil engineering applications. Blasting induces strong ground motions and fracturing of rock mass in rock excavations. Particularly, high ground motions may also induce some instability problems of rock mass and structures nearby. Furthermore, it may cause some environmental problems due to noise as well as vibrations of structures near the populated areas. Furthermore, flyrocks is another major issue for the safety of people and damage to machinery and equipments when blasting is employed. In this study, the authors explore the ways how to estimate the ground motions as a function of distance, amount of explosive, number of holes. The ground motions were measured by stand-alone accelerometers developed by the first author and some empirical relations are developed. The effect of ground motions on the instability issues of benches such as sliding, toppling and rockfalls were investigated. Furthermore, the flyrock issue is investigated and some empirical relations to estimate the maximum distance of flyrocks from the blasting relations are compared and discussed. CITATION:Aydan, O and Ulusay, R, 2018. The ground motions induced by blasting in open pit lignite mines and its environmental effects, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 142–151 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

Remote sensing techniques can be used to map joint sets in a rock mass for the estimation of in situ block size distribution and improved optimisation of blasting. This paper reviews remote sensing using photogrammetry and laser mapping for mapping rock masses and presents elements of the analyses applied to data acquired with these mapping technologies. These techniques enable a user to map areas of hundreds of square metres rapidly with high precision. Using this data computer programs such as Sirojoint can provide estimates of joint position and orientation with orientation measurement accuracies better than one degree. The paper describes the use of remote mapping and provides potential users with a description of some of the advantages and limitations of the mapping techniques and the data they produce. Mapping of lithology and structure of rock masses is an important task required in many areas of mining and construction. It is a complex task routinely performed using established techniques developed to provide consistent results under a wide range of conditions. The techniques for data acquisition and analysis described in this paper enable more accurate mapping to be performed rapidly and enable mapping of inaccessible sections of a rock mass. These techniques will provide geologists and geotechnical engineers with more detailed, accurate data than previously available.

Jan 1, 2001

At the Nikkel og Olivin nickel mine near Narvik, Norway, Outokumpu has been the operator since 1993. The mine was opened in 1989 and in 1992 Outokumpu commenced operations to secure concentrate deliveries to Harjavalta's nickel smelter in Finland. Annual production is about 740 000 tonnes of nickel ore grading 0.5 per cent Ni, about 25 000 tonnes of nickel concentrate and about 2800 tonnes of nickel metal. All production comes from underground operations which makes Nikkel og Olivin AS perhaps the lowest grade underground nickel mine in the world today. Production is currently from one of two orebodies, which is known as the Western orebody. The Eastern orebody was worked out by 1995. During Outokumpu's operational period the Western orebody has been delineated and taken to production. The underground exploration and definition drilling involved about 15 000 in of diamond drilling, which was carried out during a nine-month period. Following this a feasibility study was undertaken and production commenced. Improvements were made to the mining methods. Previously the mine utilised open pit equipment underground and this resulted in an enormous amount of additional tunnelling. Grade control and ore delineation were previously based on sparse diamond drilling and all geological information was processed manually. The improvements included the use of underground sludge drilling to increase the amount of geological information, the of a new computer system for grade control and mine planning, new automated underground longhole drilling equipment and the of underground mining equipment which reduced the size of the drives. These changes produced a marked increase in the efficiency of the underground Mine.

Jan 1, 1996

The large, low grade, Kidston Gold Mine in North Queensland has achieved outstanding economies of scale and profitability. The total mineable ore reserve including mined to-date (as at December 1993) was 70.75 million tonnes at 1.54 grams gold per tonne. After nine years of mining, grade control mine production routinely reconciles against mill production and ore reserves to within five per cent of contained gold. The grade control system developed at Kidston is examined in detail, with emphasis on the geological thinking behind the strategies, as well as the development and application of a computerised, graphical production control and reporting system. Reconciliation procedures and results are explained, illustrating the success of geostatistical methods, as a risk management tool, in both ore reserves and production grade control.

Jan 1, 1994

By R Lau

In recently completed road tunnel projects in Queensland, such as the Airport Link and the Clem7 tunnels, there is a smoke duct running along the roof of the carriageways to extract smoke in case of fire. In New South Wales, no road tunnels have a smoke duct. In the Melbourne City Link tunnels, there is a small smoke duct running along the roof. All of the tunnels are safe as claimed by the designers and authorities. However, there is significant cost associated with providing a full size smoke duct compared with no smoke duct. This paper is going to present a comparison of the road tunnel safety with a smoke duct and those without one from a risk perspective. It further discusses the cost-effectiveness of such provisions and whether similar levels of safety could be achieved without a smoke duct.CITATION:Lau, R, 2014. Smoke duct or no smoke duct for road tunnels, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 83–86 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By E R. Ramanaidou

The value of Raman spectroscopy to undertake mineral and chemical characterisation of iron ores was assessed by applying the technique to representative samples of banded iron-formations (BIF) and a BIF-derived, martite-goethite ore. The common iron oxides haematite, magnetite and goethite as well as gangue minerals such as quartz and carbonates all show distinct Raman spectra that enables these phases to be easily detected and mapped in situ for either samples prepared as polished blocks or unprepared material. Raman spectroscopy also offers the potential of in situ chemical characterisation. Shifts in the excitation bands of carbonate detected in BIF were related to the Mg content of Fe-carbonate and confirmed the first world-wide occurrence of a high Mg-bearing siderite (pistomesite) in BIF.The discriminatory power of Raman spectroscopy coupled with the potential of the technique to offer large-scale (volumetric) characterisation of iron ore will be of great value not only to the existing BID and CID ore types, but also to the newly emerging magnetite iron deposits (MID).

Jul 11, 2011